If cxgb3 calls the iw_cxgb3 t3cclient remove function due to a device
removal event, then the iwch device must be marked with CXIO_ERROR_FATAL
since the device below us is going away.  Otherwise, we can get stuck in
a deadlock as RDMA ULPs try and deallocate objects (like MRs, QPs, etc).
So always mark the device with CXIO_ERROR_FATAL when removing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Only kernel mode CQs need the SW queue memory allocated.  The SW queue
for user mode CQs is allocated in userspace by libcxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

T3 hardware doorbell FIFO overflows can cause application stalls due
to lost doorbell ring events.  This has been seen when running large
NP IMB alltoall MPI jobs.  The T3 hardware supports an xon/xoff-type
flow control mechanism to help avoid overflowing the HW doorbell FIFO.

This patch uses these interrupts to disable RDMA QP doorbell rings
when we near an overflow condition, and then turn them back on (and
ring all the active QP doorbells) when when the doorbell FIFO empties
out.  In addition if an doorbell ring is dropped by the hardware, the
code will now recover.

Design:

cxgb3:
- enable these DB interrupts
- in the interrupt handler, schedule work tasks to call the ULPs event
  handlers with the new events.
- ring all the qset txqs when an overflow is detected.

iw_cxgb3:
- disable db ringing on all active qps when we get the DB_FULL event
- enable db ringing on all active qps and ring all active dbs when we get
  the DB_EMPTY event
- On DB_DROP event:
       - disable db rings in the event handler
       - delay-schedule a work task which rings and enables the dbs on
         all active qps.
- in post_send and post_recv logic, don't ring the db if it's disabled.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Failure to rearm a CQ means the cxgb3 device is wedged, but we shouldn't
kill the whole system with a BUG_ON() if this happens.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: Do not falsely trigger kerneloops

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cciss: Make cciss_seq_show handle holes in the h->drv[] array
  cfq-iosched: split seeky coop queues after one slice

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Fix the mapping of the NFSERR_SERVERFAULT error
  NFS: Remove a redundant check for PageFsCache in nfs_migrate_page()
  NFS: Fix a bug in nfs_fscache_release_page()

* git://git.infradead.org/users/cbou/battery-2.6.33:
  wm97xx_battery: Handle missing platform data gracefully

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] qla2xxx: Obtain proper host structure during response-queue processing.
  [SCSI] compat_ioct: fix bsg SG_IO
  [SCSI] qla2xxx: make msix interrupt handler safe for irq
  [SCSI] zfcp: Report FC BSG errors in correct field
  [SCSI] mptfusion : mptscsih_abort return value should be SUCCESS instead of value 0.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - make sure we don't schedule reconnects after cleanup

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (30 commits)
  vgaarb: fix incorrect dereference of userspace pointer.
  drm/radeon/kms: retry auxch on 0x20 timeout value.
  drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
  drm/vmwgfx: Fix a circular locking dependency bug.
  drm/vmwgfx: Drop scanout flag compat and add execbuf ioctl parameter members. Bumps major.
  drm/vmwgfx: Report propper framebuffer_{max|min}_{width|height}
  drm/vmwgfx: Update the user-space interface.
  drm/radeon/kms: fix screen clearing before fbcon.
  nouveau: fix state detection with switchable graphics
  drm/nouveau: move dereferences after null checks
  drm/nv50: make the pgraph irq handler loop like the pre-nv50 version
  drm/nv50: delete ramfc object after disabling fifo, not before
  drm/nv50: avoid unloading pgraph context when ctxprog is running
  drm/nv50: align size of buffer object to the right boundaries.
  drm/nv50: disregard dac outputs in nv50_sor_dpms()
  drm/nv50: prevent multiple init tables being parsed at the same time
  drm/nouveau: make dp auxch xfer len check for reads only
  drm/nv40: make INIT_COMPUTE_MEM a NOP, just like nv50
  drm/nouveau: Add proper vgaarb support.
  drm/nouveau: Fix fbcon on mixed pre-NV50 + NV50 multicard.
  ...

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  drivers/dma: Correct NULL test
  async-tx: fix buffer submission error handling in ipu_idma.c
  dmaengine: correct onstack wait_queue_head declaration
  ioat: fix infinite timeout checking in ioat2_quiesce
  dmaengine: fix memleak in dma_async_device_unregister

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Don't probe reserved EntryHi bits.
  MIPS: SNI: Correct NULL test
  MIPS: Fix __devinit __cpuinit confusion in cpu_cache_init
  MIPS: IP27: Make defconfig useful again.
  MIPS: Fixup of the r4k timer

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cm: Revert association of an RDMA device when binding to loopback

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, apic: Don't use logical-flat mode when CPU hotplug may exceed 8 CPUs
  x86-32: Make AT_VECTOR_SIZE_ARCH=2
  x86/agp: Fix amd64-agp module initialization regression
  x86, doc: Fix minor spelling error in arch/x86/mm/gup.c

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc32: Fix thinko in previous change.
  sparc: Align clone and signal stacks to 16 bytes.

When reserving stack space for a new process, make sure we're not
attempting to expand the stack by more than rlimit allows.

This fixes a bug caused by b6a2fea3 ("mm:
variable length argument support") and unmasked by
fc63cf23 ("exec: setup_arg_pages() fails
to return errors").

This bug means that when limiting the stack to less the 20*PAGE_SIZE (eg.
80K on 4K pages or 'ulimit -s 79') all processes will be killed before
they start.  This is particularly bad with 64K pages, where a ulimit below
1280K will kill every process.

To test, do:

  'ulimit -s 15; ls'

before and after the patch is applied.  Before it's applied, 'ls' should
be killed.  After the patch is applied, 'ls' should no longer be killed.

A stack limit of 15KB since it's small enough to trigger 20*PAGE_SIZE.
Also 15KB not a multiple of PAGE_SIZE, which is a trickier case to handle
correctly with this code.

4K pages should be fine to test with.

[kosaki.motohiro@jp.fujitsu.com: cleanup]
[akpm@linux-foundation.org: cleanup cleanup]
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is used by tcgetsid(3).
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Change the LTP maintainer responsibities from 2010.

Ref: http://marc.info/?l=ltp-list&m=126502242912536&w=2

Signed-off-by : Rishikesh K Rajak <risrajak@linux.vnet.ibm.com>
Cc: Subrata Modak <subrata@linux.vnet.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Garrett Cooper <yanegomi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some unused, unsupported debug code existed in the mpc85xx EDAC driver
that resulted in a build failure when CONFIG_EDAC_DEBUG was defined:

  drivers/edac/mpc85xx_edac.c: In function 'mpc85xx_mc_err_probe':
  drivers/edac/mpc85xx_edac.c:1031: error: implicit declaration of function 'edac_mc_register_mcidev_debug'
  drivers/edac/mpc85xx_edac.c:1031: error: 'debug_attr' undeclared (first use in this function)
  drivers/edac/mpc85xx_edac.c:1031: error: (Each undeclared identifier is reported only once
  drivers/edac/mpc85xx_edac.c:1031: error: for each function it appears in.)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit b4846251 ("edac: mpc85xx add
mpc83xx support") accidentally broke how a chip select's first and last
page addresses are calculated.  The page addresses are being shifted too
far right by PAGE_SHIFT.  This results in errors such as:

  EDAC MPC85xx MC1: Err addr: 0x003075c0
  EDAC MPC85xx MC1: PFN: 0x00000307
  EDAC MPC85xx MC1: PFN out of range!
  EDAC MC1: INTERNAL ERROR: row out of range (4 >= 4)
  EDAC MC1: CE - no information available: INTERNAL ERROR

The vaule of PAGE_SHIFT is already being taken into consideration during
the calculation of the 'start' and 'end' variables, thus it is not
necessary to account for it again when setting a chip select's first and
last page address.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes a bug in the multiblock write tests where the written
data is read back for verifying one block at a time.  The tests in
mmc_test assumes that all cards are byte addressable.

This will cause the multi block write tests to fail, leading the user of
the mmc_test driver thinking there is something wrong with the sdhci
driver they are testing.

The start address for the block is calculated as: blocknum * 512. For
block addressable cards the blocknum alone should be used.
Signed-off-by: Johan Kristell <johan.kristell@axis.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When suspending, tpm_infineon calls the generic suspend function of the
TPM framework.  However, the TPM framework does not return and the system
hangs upon suspend.  When sending the necessary command "TPM_SaveState"
directly within the driver, suspending and resuming works fine.
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: <stable@kernel.org>		[2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Should mask stack with 0xf not "0x15".

Noticed by Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An unfortunate "WARNING" in the message amd64_edac dumps when the system
doesn't support DRAM ECC or ECC checking is not enabled in the BIOS
used to trigger kerneloops which qualified the message as an OOPS thus
misleading the users. See, e.g.

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/422536
http://bugzilla.kernel.org/show_bug.cgi?id=15238

Downgrade the message level to KERN_NOTICE and fix the formulation.

Cc: stable@kernel.org # .32.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>

This patch corrects a userspace pointer dereference in the VGA arbiter
in 2.6.32.1.

copy_from_user() is used at line 822 to copy the contents of buf into
kbuf, but a call to strncmp() on line 964 uses buf rather than kbuf.  This
problem led to a GPF in strncmp() when X was started on my x86_32 systems.
 X triggered the behavior with a write of "target PCI:0000:01:00.0" to
/dev/vga_arbiter.

The patch has been tested against 2.6.32.1 and observed to correct the GPF
observed when starting X or manually writing the string "target
PCI:0000:01:00.0" to /dev/vga_arbiter.
Signed-off-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* 'drm-radeon-linus' of ../drm-next:
  drm/radeon/kms: retry auxch on 0x20 timeout value.
  drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
  drm/radeon/kms: fix screen clearing before fbcon.
  drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
  drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
  drm/radeon/kms: change Kconfig text to reflect the new option.
  drm/radeon/kms: suspend and resume audio stuff

ATOM appears to return 0x20 which seems to mean some sort of timeout.

retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>

radeon_copy_dma is only available for r200 or newer cards.
Call to radeon_copy_dma would result to NULL pointer
dereference if benchmarking asic without dma engine.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* 'nouveau/for-airlied' of /home/airlied/kernel/drm-next:
  nouveau: fix state detection with switchable graphics
  drm/nouveau: move dereferences after null checks
  drm/nv50: make the pgraph irq handler loop like the pre-nv50 version
  drm/nv50: delete ramfc object after disabling fifo, not before
  drm/nv50: avoid unloading pgraph context when ctxprog is running
  drm/nv50: align size of buffer object to the right boundaries.
  drm/nv50: disregard dac outputs in nv50_sor_dpms()
  drm/nv50: prevent multiple init tables being parsed at the same time
  drm/nouveau: make dp auxch xfer len check for reads only
  drm/nv40: make INIT_COMPUTE_MEM a NOP, just like nv50
  drm/nouveau: Add proper vgaarb support.
  drm/nouveau: Fix fbcon on mixed pre-NV50 + NV50 multicard.
  drivers/gpu/drm/nouveau/nouveau_grctx.c: correct NULL test
  drm/nouveau: call ttm_bo_wait with the bo lock held to prevent hang
  drm/nouveau: Fixup semaphores on pre-nv50 cards.
  drm/nouveau: Add getparam to get available PGRAPH units.
  drm/nouveau: Add module options to disable acceleration.
  drm/nouveau: fix non-vram notifier blocks

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Even if this bumps the version to 1 it does not mean the driver is
out of staging. From what we know this is the last backwards
incompatible change to the driver.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

When time-based throttling is implemented, we need to bump minor.
When the old way of detecting scanout is removed, we need to bump major.
In the meantime, this change should not break existing user-space.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This memset_io was added to debug something way back and got
left behind, memset the fb to black so the borders don't be all white.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The patch that adds cpu_probe_vmbits is erroneously writing to reserved
bit 12.  Since we are really only probing high bits, don't write this bit
with a one.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Patchwork: http://patchwork.linux-mips.org/patch/949/Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Test the value that was just allocated rather than the previously tested one.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@

if (x == NULL || ...) {
    ... when forall
    return ...; }
... when != goto l;
    when != x = e
    when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
To: kernel-janitors@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/945/Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>