Merge branch 'for_3.7/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into devel-dt

Support the blue LED connected to the LEDB pin of the TWL4030
on the Gumstix Overo.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add the Tobi/Overo board to the list of supported platforms.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

The Gumstix Overo is a computer on module using an OMAP3 processor.
This module must be plugged into an expansion board.

This patch adds a first device tree support for the Overo, using the
Tobi expansion board. The current support is able to boot and mount
the rootfs from MMC.

This patche also updates the omap3 dtb build target.

Currently working:
- mmc0 (on board microSD)
- i2c0 and i2c2 (i2c1 not used)
- led on GPIO
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Thanks to Vaibhav <hvaibhav@ti.com> omap_device fix
(ARM: OMAP: omap_device: Fix up resource names when booted with devicetre),
we can now specify reg and interrupts using standard device tree
attributes.

Update the OMAP4 dtsi file with missing reg and interrupts attributes.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

The device/node resources (like, IORESOURCE_MEM and IORESOURCE_IRQ)
are overwritten by hwmod resources, due to all known reasons but
that should not be the reason for not providing all the information
in the DTS blob. Ideally we should use DTS resource and use HWMOD
framework wherever required and for only specific things.

Newer platforms like, OMAP5 and AM33XX, we only support DT boot mode,
so this patch is preparation for the future where we supposed to get
rid of hwmod dependency anyway.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

To make it consistent, convert all hex number presentation
to lower-case from all am33xx specific nodes.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add the needed sections to enable audio support on BeagleBoard when booted
with DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

To be able to load the McPDM and DMIC driver when booted with device tree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Create the sections describing the McBSP ports to be able to use them via
DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

In order to get the memory areas by name when booted with DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Create the sections describing the McBSP ports to be able to use them via
DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Create the needed sections to be able to probe McBSP ports via DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Since the board is based on OMAP2420 we should include the dedicated dtsi
file (which includes the common omap2 dtsi).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

The McBSP IP within OMAP2420 and 2430 is different we need to create separate
dtsi files for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add the support for D6 and D7 LEDs on Beagle board.
- D6 will be used for heartbeat
- D7 will be used for mmc0
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add device tree properties for twl4030/gpio, according to the
platform data of corresponding boards. This enables the led
connected to LEDB output for both boards, as well as
pullups/pulldowns on GPIO for the BeagleBoard.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>

Adds a number of missing device tree properties for
twl4030/gpio, and update bindings:
- "ti,use-leds"  -> .use_leds
- "ti,debounce"  -> .debounce
- "ti,mmc-cd"    -> .mmc_cd
- "ti,pullups"   -> .pullups
- "ti,pulldowns" -> .pulldowns
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
[b-cousson@ti.com: Fix some checkpatch CHECK issues]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Remove some useless comment and move GIC controller outside
of the OCP node since it does use the MPU internal bus and
not the OCP.
This will not change the functionality but will reflect the
reality more accurately.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add cortex-a9 local timer support for all OMAP4 based
SOCs using DT.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Provide PL310 Level 2 Cache Controller Device Tree
support for OMAP4 based devices.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Device tree data for the EMIF sdram controllers in OMAP4
and LPDDR2 memory devices attached to OMAP4 boards.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[b-cousson@ti.com: Use label in board to access EMIF nodes]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

EMIF - External Memory Interface - is an SDRAM controller used in
TI SoCs. EMIF supports, based on the IP revision, one or more of
DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
of the EMIF IP and memory parts attached to it.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

device tree bindings for LPDDR2 SDRAM memories compliant
to JESD209-2 standard.

The 'lpddr2' binding in-turn uses another binding 'lpddr2-timings'
for specifying the AC timing parameters of the memory device at
different speed-bins.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add Description for tmp102 temperature sensor.

Cc: Felipe Balbi <balbi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add keypad data node in omap4 device tree file.
Also fill the device tree binding parameters
with the required value in "omap4-sdp" dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[b-cousson@ti.com: Re-align the entries and the comments]

Add bmp085 pressure sensor data in omap5 evm dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add keypad data node in omap5 device tree file.
Also fill the device tree binding parameters
with the required value in "omap5-evm" dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[b-cousson@ti.com: Fix merge issue with MMC patches,
put node at the proper place, align entries and comments]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add tmp102 temperature sensor data in omap5 evm dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add I2C data nodes in omap5 device tree file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

With the new devices (like, AM33XX and OMAP5) we now only support
DT boot mode of operation and now it is the time to start killing
slowly the dependency on hwmod, so with this patch, we are starting
with device resources.
The idea here is implemented considering to both boot modes -
  - DT boot mode
    OF framework will construct the resource structure (currently
    does for MEM & IRQ resource) and we should respect/use these
    resources, killing hwmod dependency.
    If pdev->num_resources > 0, we assume that MEM & IRQ resources
    have been allocated by OF layer already (through DTB).

    Once DMA resource is available from OF layer, we should
    kill filling any resources from hwmod.

  - Non-DT boot mode
    Here, pdev->num_resources = 0, and we should get all the
    resources from hwmod (following existing steps)
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
[b-cousson@ti.com: Fix some checkpatch CHECK issues]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

When booted with some resource will have their name set to NULL. This can
cause later kernel crash since this is not expected by the platform code.

When we boot without DT the devices are created with platform_device_add()
which itself fixes up the missing resource names:
if (r->name == NULL)
	r->name = dev_name(&pdev->dev);

The of core also fixes up the resource names when taking the information
from DT data - in __of_address_to_resource():
r->name = name ? name : dev->full_name;

When we boot OMAP with devicetree: of will create the devices based on the
DT data so the resource names are guarantied to be not NULL. Since we have
the 'ti,hwmod' tag, we remove the of created resources from the device and
re-create them based on hwmod data. If the hwmod data does not specify a
name for a resource it will be NULL.
This can cause kernel crash if the driver uses
platform_get_resource_byname() to get any resource.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[b-cousson@ti.com: Change omap_hwmod to omap_device in subject]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>

Add tps65217 regulator device tree data to AM335x-Bone by adding
regulator consumers with tightened constraints and regulator-name.
TPS65217 regulator handle can be obtained by using this regulator
name.

This patch also add I2C node with I2C frequency and tps65217 PMIC
I2C slave address.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add tps65910 regulator device tree data to AM335x-EVM by adding
regulator consumers with tightened constraints and regulator-name.
TPS65910 regulator handle can be obtained by using this regulator
name.

This patch also add I2C node with I2C frequency and tps65910 PMIC
I2C slave address.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add device tree data for tps65217 regulator by adding all tps65217
regulator nodes. Regulator is initialized based on compatiable
name provided in tps65217 DT file.

All tps65910 PMIC regulator device tree nodes are placed in a
seperate device tree include file (tps65217.dtsi). This patch
was tested on AM335x-Bone.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add device tree data for tps65910 regulator by adding all tps65910
regulator nodes. Regulator is initialized based on compatiable
name provided in tps65910 DT file.

All tps65910 PMIC regulator device tree nodes are placed in a
seperate device tree include file (tps65910.dtsi). This patch
was tested on AM335x-EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

regulators do not have a 'reg' property, hence the regulator@0,
regulator@1 do not make sense. get rid of it.
Reported-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Makes it easier to just do 'make dtbs' for whatever the kernel was
configured for, just like some other platforms.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Ideally in common SoC dtsi file should set all modules
to "disabled" state and it should get enabled in respective
EVM/Board dts file as per usage.

This patch sets default status of all modules to "disabled"
state in am33xx.dtsi file. Currently there are no modules
supported as part of Bone and EVM dts support, so care
to add entry "status = "okay"" while adding support for any
module.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>