The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.

Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

iMX50 pin mux options for pads KEY_COL2 and KEY_COL3 allow muxing the same
KEY_COL instances as the pad name. Fix typos shifting KEY_COL instances.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently when trying to use the 'devmem' tool to read/write
registers the following bus error is observed:

[   82.689185] Unhandled fault: external abort on non-linefetch (0x1018) at 0xb6ff10c4
[   82.697071] pgd = (ptrval)
[   82.699920] [b6ff10c4] *pgd=a87c5831, *pte=73fa8383, *ppte=73fa8a33
Bus error

Add the aipstz nodes, so that the following function from
imx51_dt_init() can work properly:

	imx_aips_allow_unprivileged_access("fsl,imx51-aipstz");

After adding these nodes, 'devmem' tool can work correctly,
which is very useful for debugging purposes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This was removed in commit 5eaeaccd ("ARM: dts: imx7d-sdb: Pass
'enable-gpios' and 'power-supply' properties") with a note claiming that
GPIO1_IO01 is connected to a pin labeled as "PWREN" on the connector.

Despite that label this pin does actually work as a PWM controlling
brightness. So restore pwm functionality.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6SLL uses same SRC module as i.MX51, add "fsl,imx51-src"
compatible string to enable SRC driver to support setting
CPU resume address for cpu-idle and suspend/resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The RIoTboard debug uart is connected to serial1.
Add a chosen property in the DTS so OS knows what serial port to use for
the console.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add #cooling-cells for i.MX6/7 SoCs for cpufreq cooling device usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the CodaHx4 VPU to the i.MX51 device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Two different regulators are defined with the same name and label but
distinct properties.

The first definition was added with the first board dts and the second
was added when upstream added flexcan support.

Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.

The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer

Added under i2cmux/i2c@1 because they're not otherwise accessible.

These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452

Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.

This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.

notable features:
CPU                 NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory              Up to 2 GB DDR3-1066
Video Interfaces    Up to 1 Parallel Up to 2 LVDS HDMI 1.4
                    port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

USB OTG power is switched on when the GPIO is pulled low.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

To match the convention, move regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

To match the convention, move all regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure that MX51_PAD_GPIO1_1 does not remain configure as
ALT0/SD1_WP (it is out of reset). This is needed because of external
pull-up resistor attached to that pad that, when left unchanged, will
drive SD1_WP high preventing eSDHC1/eMMC from working correctly.

To fix that add a pinmux configuration line configureing the pad to
function as a GPIO. While we are at it, add a corresponding
output-high GPIO hog in an effort to minimize current consumption.

Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds rave-sp powerbutton and backlight devices to RDU1 device tree.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit provides support for HSC and DDC boards from
Kieback&Peter GmbH vendor.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add dts file support for imx6sll EVK board.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add dtsi file for imx6sll.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull block fixes from Jens Axboe:
 "A collection of fixes that should go into -rc1. This contains:

   - bsg_open vs bsg_unregister race fix (Anatoliy)

   - NVMe pull request from Christoph, with fixes for regressions in
     this window, FC connect/reconnect path code unification, and a
     trace point addition.

   - timeout fix (Christoph)

   - remove a few unused functions (Christoph)

   - blk-mq tag_set reinit fix (Roman)"

* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
  bsg: fix race of bsg_open and bsg_unregister
  block: remov blk_queue_invalidate_tags
  nvme-fabrics: fix and refine state checks in __nvmf_check_ready
  nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
  nvme-fabrics: refactor queue ready check
  blk-mq: remove blk_mq_tagset_iter
  nvme: remove nvme_reinit_tagset
  nvme-fc: fix nulling of queue data on reconnect
  nvme-fc: remove reinit_request routine
  blk-mq: don't time out requests again that are in the timeout handler
  nvme-fc: change controllers first connect to use reconnect path
  nvme: don't rely on the changed namespace list log
  nvmet: free smart-log buffer after use
  nvme-rdma: fix error flow during mapping request data
  nvme: add bio remapping tracepoint
  nvme: fix NULL pointer dereference in nvme_init_subsystem
  blk-mq: reinit q->tag_set_list entry only after grace period

Pull documentation fixes from Mauro Carvalho Chehab:
 "This solves a series of broken links for files under Documentation,
  and improves a script meant to detect such broken links (see
  scripts/documentation-file-ref-check).

  The changes on this series are:

   - can.rst: fix a footnote reference;

   - crypto_engine.rst: Fix two parsing warnings;

   - Fix a lot of broken references to Documentation/*;

   - improve the scripts/documentation-file-ref-check script, in order
     to help detecting/fixing broken references, preventing
     false-positives.

  After this patch series, only 33 broken references to doc files are
  detected by scripts/documentation-file-ref-check"

* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
  fix a series of Documentation/ broken file name references
  Documentation: rstFlatTable.py: fix a broken reference
  ABI: sysfs-devices-system-cpu: remove a broken reference
  devicetree: fix a series of wrong file references
  devicetree: fix name of pinctrl-bindings.txt
  devicetree: fix some bindings file names
  MAINTAINERS: fix location of DT npcm files
  MAINTAINERS: fix location of some display DT bindings
  kernel-parameters.txt: fix pointers to sound parameters
  bindings: nvmem/zii: Fix location of nvmem.txt
  docs: Fix more broken references
  scripts/documentation-file-ref-check: check tools/*/Documentation
  scripts/documentation-file-ref-check: get rid of false-positives
  scripts/documentation-file-ref-check: hint: dash or underline
  scripts/documentation-file-ref-check: add a fix logic for DT
  scripts/documentation-file-ref-check: accept more wildcards at filenames
  scripts/documentation-file-ref-check: fix help message
  media: max2175: fix location of driver's companion documentation
  media: v4l: fix broken video4linux docs locations
  media: dvb: point to the location of the old README.dvb-usb file
  ...

Pull fsnotify updates from Jan Kara:
 "fsnotify cleanups unifying handling of different watch types.

  This is the shortened fsnotify series from Amir with the last five
  patches pulled out. Amir has modified those patches to not change
  struct inode but obviously it's too late for those to go into this
  merge window"

* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: add fsnotify_add_inode_mark() wrappers
  fanotify: generalize fanotify_should_send_event()
  fsnotify: generalize send_to_group()
  fsnotify: generalize iteration of marks by object type
  fsnotify: introduce marks iteration helpers
  fsnotify: remove redundant arguments to handle_event()
  fsnotify: use type id to identify connector object type

Pull fbdev updates from Bartlomiej Zolnierkiewicz:
 "There is nothing really major here, few small fixes, some cleanups and
  dead drivers removal:

   - mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen)

   - add missing module license tags to omap/omapfb driver (Arnd
     Bergmann)

   - add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd
     Bergmann)

   - convert savagefb, aty128fb & radeonfb drivers to use msleep & co.
     (Jia-Ju Bai)

   - allow COMPILE_TEST build for viafb driver (media part was reviewed
     by media subsystem Maintainer)

   - remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm
     drivers (drm parts were acked by shmob-drm driver Maintainer)

   - remove unused auo_k190xfb drivers

   - misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy
     Shevchenko, Colin Ian King)"

* tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits)
  fb_omap2: add gpiolib dependency
  video/omap: add module license tags
  MAINTAINERS: make omapfb orphan
  video: fbdev: pxafb: match_string() conversion fixup
  video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling"
  video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer"
  video: fbdev: pxafb: Convert to use match_string() helper
  video: fbdev: via: allow COMPILE_TEST build
  video: fbdev: remove unused sh_mobile_meram driver
  drm: shmobile: remove unused MERAM support
  video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support
  video: fbdev: remove unused auo_k190xfb drivers
  video: omap: Improve a size determination in omapfb_do_probe()
  video: sm501fb: Improve a size determination in sm501fb_probe()
  video: fbdev-MMP: Improve a size determination in path_init()
  video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions
  video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe()
  video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions
  video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe()
  video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency
  ...

Pull AFS updates from Al Viro:
 "Assorted AFS stuff - ended up in vfs.git since most of that consists
  of David's AFS-related followups to Christoph's procfs series"

* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs: Optimise callback breaking by not repeating volume lookup
  afs: Display manually added cells in dynamic root mount
  afs: Enable IPv6 DNS lookups
  afs: Show all of a server's addresses in /proc/fs/afs/servers
  afs: Handle CONFIG_PROC_FS=n
  proc: Make inline name size calculation automatic
  afs: Implement network namespacing
  afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
  afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
  proc: Add a way to make network proc files writable
  afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
  afs: Rearrange fs/afs/proc.c to move the show routines up
  afs: Rearrange fs/afs/proc.c by moving fops and open functions down
  afs: Move /proc management functions to the end of the file

Pull compat updates from Al Viro:
 "Some biarch patches - getting rid of assorted (mis)uses of
  compat_alloc_user_space().

  Not much in that area this cycle..."

* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  orangefs: simplify compat ioctl handling
  signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
  vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart

Pull aio fixes from Al Viro:
 "Assorted AIO followups and fixes"

* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  eventpoll: switch to ->poll_mask
  aio: only return events requested in poll_mask() for IOCB_CMD_POLL
  eventfd: only return events requested in poll_mask()
  aio: mark __aio_sigset::sigmask const

Pull networking fixes from David Miller:

 1) Various netfilter fixlets from Pablo and the netfilter team.

 2) Fix regression in IPVS caused by lack of PMTU exceptions on local
    routes in ipv6, from Julian Anastasov.

 3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.

 4) Don't crash on poll in TLS, from Daniel Borkmann.

 5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
    including Avahi mDNS. From Bart Van Assche.

 6) Missing of_node_put in qcom/emac driver, from Yue Haibing.

 7) We lack checking of the TCP checking in one special case during SYN
    receive, from Frank van der Linden.

 8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.

 9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.

10) Must grab HW caps before doing quirk checks in stmmac driver, from
    Jose Abreu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
  net: stmmac: Run HWIF Quirks after getting HW caps
  neighbour: skip NTF_EXT_LEARNED entries during forced gc
  net: cxgb3: add error handling for sysfs_create_group
  tls: fix waitall behavior in tls_sw_recvmsg
  tls: fix use-after-free in tls_push_record
  l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
  l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
  mlxsw: spectrum_switchdev: Fix port_vlan refcounting
  mlxsw: spectrum_router: Align with new route replace logic
  mlxsw: spectrum_router: Allow appending to dev-only routes
  ipv6: Only emit append events for appended routes
  stmmac: added support for 802.1ad vlan stripping
  cfg80211: fix rcu in cfg80211_unregister_wdev
  mac80211: Move up init of TXQs
  mac80211_hwsim: fix module init error paths
  cfg80211: initialize sinfo in cfg80211_get_station
  nl80211: fix some kernel doc tag mistakes
  hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
  rds: avoid unenecessary cong_update in loop transport
  l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
  ...

Pull module updates from Jessica Yu:
 "Minor code cleanup and also allow sig_enforce param to be shown in
  sysfs with CONFIG_MODULE_SIG_FORCE"

* tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: Allow to always show the status of modsign
  module: Do not access sig_enforce directly

Pull uml updates from Richard Weinberger:
 "Minor updates for UML:

   - fixes for our new vector network driver by Anton

   - initcall cleanup by Alexander

   - We have a new mailinglist, sourceforge.net sucks"

* 'for-linus-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Fix raw interface options
  um: Fix initialization of vector queues
  um: remove uml initcalls
  um: Update mailing list address