- 11 Dec, 2017 31 commits
-
-
Mauro Carvalho Chehab authored
The current code doesn't report tuner lock properly if the tuner get_status callback is not available, as reported by smatch: drivers/media/dvb-frontends/stv090x.c:2220 stv090x_get_coldlock() error: uninitialized symbol 'reg'. Signed-off-by:Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Mauro Carvalho Chehab authored
If, for some reason, reading the hwmodel register on xc4000 fails, it will cause the following logig to use a random value, as reported by smatch: drivers/media/tuners/xc4000.c:1047 check_firmware() error: uninitialized symbol 'hwmodel'. drivers/media/tuners/xc4000.c:1060 check_firmware() error: uninitialized symbol 'hwmodel'. drivers/media/tuners/xc4000.c:1064 check_firmware() error: uninitialized symbol 'hwmodel'. Signed-off-by: -
Mauro Carvalho Chehab authored
The logic at si476x_radio_s_hw_freq_seek() checks if the frequency range that will be used to handle hardware seek has the minimal frequency under rangelow. That works fine if userspace zeros both fields. However, if userspace fills either seek->rangelow or seek-rangehigh, it won't read the corresponding range from the device, causing the values to be unitialized, as warned by smatch: drivers/media/radio/radio-si476x.c:789 si476x_radio_s_hw_freq_seek() error: uninitialized symbol 'rangelow'. drivers/media/radio/radio-si476x.c:789 si476x_radio_s_hw_freq_seek() error: uninitialized symbol 'rangehigh'. Fix it by initializing those vars from the values present at the struct v4l2_hw_freq_seek. While here, simplify the logic which reads such values from the hardware limits. Signed-off-by: -
Mauro Carvalho Chehab authored
The logic at qt1010_init_meas1() and qt1010_init_meas2() are too complex for static analizers to identify that some vars are always be initialized. That causes smatch to produce the following warnings: drivers/media/tuners/qt1010.c:248 qt1010_init_meas1() error: uninitialized symbol 'val2'. drivers/media/tuners/qt1010.c:282 qt1010_init_meas2() error: uninitialized symbol 'val'. So, add annotations to prevent those bogus warnings. Signed-off-by: -
Mauro Carvalho Chehab authored
The tuning logic at tda8290 relies on agc_stat and adc_sat to be initialized. However, as warned by smatch: drivers/media/tuners/tda8290.c:261 tda8290_set_params() error: uninitialized symbol 'agc_stat'. drivers/media/tuners/tda8290.c:261 tda8290_set_params() error: uninitialized symbol 'adc_sat'. drivers/media/tuners/tda8290.c:262 tda8290_set_params() error: uninitialized symbol 'adc_sat'. That could cause an erratic behavior if PLL is not locked, as the code will only work if !(pll_stat & 0x80) && (adc_sat < 20) So, initialize it to zero, in order to let the code below to be called, with should give more chances to adjust the tuner gain, in order to get a PLL lock. Signed-off-by: -
Mauro Carvalho Chehab authored
As warned by smatch: drivers/media/platform/atmel/atmel-isc.c:2097 isc_parse_dt() error: uninitialized symbol 'ret'. The problem here is that of_graph_get_next_endpoint() can potentially return NULL on its first pass, with would make it return a random value, as ret is not initialized. While here, use while(1) instead of for(; ;), as while is the preferred syntax for such kind of loops. Signed-off-by: -
Matthias Schwarzott authored
Fix bug by moving the i2c_unregister_device calls after deregistration of dvb frontend. The new style i2c drivers already destroys the frontend object at i2c_unregister_device time. When the dvb frontend is unregistered afterwards it leads to this oops: [ 6058.866459] BUG: unable to handle kernel NULL pointer dereference at 00000000000001f8 [ 6058.866578] IP: dvb_frontend_stop+0x30/0xd0 [dvb_core] [ 6058.866644] PGD 0 [ 6058.866646] P4D 0 [ 6058.866726] Oops: 0000 [#1] SMP [ 6058.866768] Modules linked in: rc_pinnacle_pctv_hd(O) em28xx_rc(O) si2157(O) si2168(O) em28xx_dvb(O) em28xx(O) si2165(O) a8293(O) tda10071(O) tea5767(O) tuner(O) cx23885(O) tda18271(O) videobuf2_dvb(O) videobuf2_dma_sg(O) m88ds3103(O) tveeprom(O) cx2341x(O) v4l2_common(O) dvb_core(O) rc_core(O) videobuf2_memops(O) videobuf2_v4l2(O) videobuf2_core(O) videodev(O) media(O) bluetooth ecdh_generic ums_realtek uas rtl8192cu rtl_usb rtl8192c_common rtlwifi usb_storage snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic i2c_mux snd_hda_intel snd_hda_codec snd_hwdep x86_pkg_temp_thermal snd_hda_core kvm_intel kvm irqbypass [last unloaded: videobuf2_memops] [ 6058.867497] CPU: 2 PID: 7349 Comm: kworker/2:0 Tainted: G W O 4.13.9-gentoo #1 [ 6058.867595] Hardware name: MEDION E2050 2391/H81H3-EM2, BIOS H81EM2W08.308 08/25/2014 [ 6058.867692] Workqueue: usb_hub_wq hub_event [ 6058.867746] task: ffff88011a15e040 task.stack: ffffc90003074000 [ 6058.867825] RIP: 0010:dvb_frontend_stop+0x30/0xd0 [dvb_core] [ 6058.867896] RSP: 0018:ffffc90003077b58 EFLAGS: 00010293 [ 6058.867964] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000010040001f [ 6058.868056] RDX: ffff88011a15e040 RSI: ffffea000464e400 RDI: ffff88001cbe3028 [ 6058.868150] RBP: ffffc90003077b68 R08: ffff880119390380 R09: 000000010040001f [ 6058.868241] R10: ffffc90003077b18 R11: 000000000001e200 R12: ffff88001cbe3028 [ 6058.868330] R13: ffff88001cbe68d0 R14: ffff8800cf734000 R15: ffff8800cf734098 [ 6058.868419] FS: 0000000000000000(0000) GS:ffff88011fb00000(0000) knlGS:0000000000000000 [ 6058.868511] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6058.868578] CR2: 00000000000001f8 CR3: 00000001113c5000 CR4: 00000000001406e0 [ 6058.868662] Call Trace: [ 6058.868705] dvb_unregister_frontend+0x2a/0x80 [dvb_core] [ 6058.868774] em28xx_dvb_fini+0x132/0x220 [em28xx_dvb] [ 6058.868840] em28xx_close_extension+0x34/0x90 [em28xx] [ 6058.868902] em28xx_usb_disconnect+0x4e/0x70 [em28xx] [ 6058.868968] usb_unbind_interface+0x6d/0x260 [ 6058.869025] device_release_driver_internal+0x150/0x210 [ 6058.869094] device_release_driver+0xd/0x10 [ 6058.869150] bus_remove_device+0xe4/0x160 [ 6058.869204] device_del+0x1ce/0x2f0 [ 6058.869253] usb_disable_device+0x99/0x270 [ 6058.869306] usb_disconnect+0x8d/0x260 [ 6058.869359] hub_event+0x93d/0x1520 [ 6058.869408] ? dequeue_task_fair+0xae5/0xd20 [ 6058.869467] process_one_work+0x1d9/0x3e0 [ 6058.869522] worker_thread+0x43/0x3e0 [ 6058.869576] kthread+0x104/0x140 [ 6058.869602] ? trace_event_raw_event_workqueue_work+0x80/0x80 [ 6058.869640] ? kthread_create_on_node+0x40/0x40 [ 6058.869673] ret_from_fork+0x22/0x30 [ 6058.869698] Code: 54 49 89 fc 53 48 8b 9f 18 03 00 00 0f 1f 44 00 00 41 83 bc 24 04 05 00 00 02 74 0c 41 c7 84 24 04 05 00 00 01 00 00 00 0f ae f0 <48> 8b bb f8 01 00 00 48 85 ff 74 5c e8 df 40 f0 e0 48 8b 93 f8 [ 6058.869850] RIP: dvb_frontend_stop+0x30/0xd0 [dvb_core] RSP: ffffc90003077b58 [ 6058.869894] CR2: 00000000000001f8 [ 6058.875880] ---[ end trace 717eecf7193b3fc6 ]--- Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
Krzysztof Hałasa authored
Bitmask for the MIPI CSI-2 data PHY status doesn't seem to be correct. Fix it. Signed-off-by:
Krzysztof Ha?asa <khalasa@piap.pl> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
drivers/media/pci/ddbridge/ddbridge-ci.c:321:5: warning: no previous prototype for 'ddb_ci_attach' [-Wmissing-prototypes] int ddb_ci_attach(struct ddb_port *port, u32 bitrate) ^~~~~~~~~~~~~ Signed-off-by: -
Daniel Scheller authored
Update the driver version number/string to 0.9.32-integrated. Signed-off-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
-
Daniel Scheller authored
Add missing state->modcod update from upstream driver which needs to be done when manage_matype_info() sets is_vcm on certain S2 transponders. Signed-off-by:
-
Daniel Scheller authored
Add a ddb_ prefix to the two functions to better avoid conflicts in the global namespace, ie. when building everything into the kernel image. Signed-off-by:
-
Daniel Scheller authored
Rename the MaxS4/8 support files following upstream. References to these files and descriptions have been updated aswell. Signed-off-by:
-
Daniel Scheller authored
slot_ts_enable_xo2() logged debug output to info instead of debug, so fix this up. Signed-off-by:
-
Daniel Scheller authored
Move all CI device support related code from ddbridge-core to ddbridge-ci, following the previously split off MaxS4/8 support. Signed-off-by:
-
Daniel Scheller authored
Fixes several alignment, braces, space-before-cast, camelcase et al issues reported by checkpatch --strict, plus a few more checkpatch didn't report. Three checks are left after this though: - one CamelCase in ddbridge-core, related to defines/vars/enums referenced from the stv090x demod driver - one macro argument reuse in ddbridge-core aswell - one unbalanced braces around else in ddbridge-main, which is due to #ifdefs related to CONFIG_PCI_MSI, which preferrably should be kept as-is for readability. Signed-off-by:
-
Daniel Scheller authored
These are only used in C/T demod attach functions, don't add any real benefit (ie. line length savings) and in case of cxd28xx_attach aren't even used consequently. Remove them. Signed-off-by:
-
Mauro Carvalho Chehab authored
The tuning logic is broken with regards to status report: it relies on a previously-cached value that may not be valid if re-tuned. Change the logic to always read the status. Acked-by:
-
Akinobu Mita authored
Fix typo s/:/;/ Cc: Rob Herring <robh+dt@kernel.org> Cc: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Maciej S. Szmigiero authored
If set_fmt callback is called with format->width or format->height set to zero and HACTIVE_CNT or VACTIVE_CNT bits (respectively) in chip are zero we will divide by zero later in this callback when we try to calculate HSC or VSC values. Fix this by explicitly rejecting these values. Signed-off-by:
Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by:
-
Maciej S. Szmigiero authored
A 0b1100 value in 4 LSBs of "General Status 1" register (AFD_FMT_STAT) has known meaning for CX2584x-series chips - it means that a SECAM signal is currently detected by the chip. Use this opportunity to also fix wrong binary values that were present as comments attached to some entries in an array where chip register -> V4L2 standard mappings are stored. Signed-off-by:
-
Russell King authored
Setting a burst size of "8" doesn't work for IMX219 with 8-bit bayer, but a burst size of "16" does. Fix this. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Acked-by:
-
Russell King authored
The complete handler walks all entities, expecting to find an imx subdevice for each and every entity. However, camera drivers such as smiapp can themselves contain multiple entities, for which there will not be an imx subdevice. This causes imx_media_find_subdev_by_sd() to fail, making the imx capture system unusable with such cameras. Work around this by killing the error entirely, thereby allowing the imx capture to be used with such cameras. Signed-off-by:
-
Malcolm Priestley authored
When the tuner was split from m88rs2000 the attach function is in wrong place. Move to dm04_lme2510_tuner to trap errors on failure and removing a call to lme_coldreset. Prevents driver starting up without any tuner connected. Fixes to trap for ts2020 fail. LME2510(C): FE Found M88RS2000 ts2020: probe of 0-0060 failed with error -11 ... LME2510(C): TUN Found RS2000 tuner kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Tested-by:
-
Malcolm Priestley authored
Warm start has no check as whether a genuine device has connected and proceeds to next execution path. Check device should read 0x47 at offset of 2 on USB descriptor read and it is the amount requested of 6 bytes. Fix for kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access as Reported-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, add the proper SPDX, better identifying the licenses whith apply to the source code. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2 at the Siano's common driver. Some codes there are licensed on GPL v2 or latter, while others are GPL v2 only. So, in order to reflect the common license that applies to everything, the module itself should be GPLv2 only. While here, use the Kernel's coding style for the comments with copyright info. Signed-off-by: -
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several RC keymap files I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to identify GPL v2, as this is the minimal license requirement for those modles. Signed-off-by: -
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
Philippe Ombredanne <pombredanne@nexb.com> Acked-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
-
- 08 Dec, 2017 9 commits
-
-
Laurent Pinchart authored
According to the UVC specification, stream error events carry no data. Fix a buffer overflow (that should be harmless given data alignment) when reporting the stream error event by removing the data byte from the message. Signed-off-by:
-
Baoyou Xie authored
Some cameras post inaccurate frame where next frame data overlap it. this results in screen flicker, and it need to be prevented. So this patch marks the buffer error to discard the frame where buffer overflow. Signed-off-by:
Baoyou Xie <baoyou.xie@linaro.org> Reviewed-by:
-
Jaejoong Kim authored
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0] by & operation with 0x7ff. So, we can remove the duplicate & operation with 0x7ff. Signed-off-by:
Jaejoong Kim <climbbb.kim@gmail.com> Reviewed-by:
-
Nicolas Dufresne authored
Microsoft HoloLense UVC sensor uses D3DFMT instead of FOURCC when exposing formats. This adds support for D3DFMT_L8 as exposed from the Acer Windows Mixed Reality Headset. Signed-off-by:
Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by:
-
Vasyl Gomonovych authored
Fix ptr_ret.cocci warnings: drivers/media/platform/exynos4-is/fimc-lite.c:1465:1-3: WARNING: PTR_ERR_OR_ZERO can be used Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR Generated by: scripts/coccinelle/api/ptr_ret.cocci Signed-off-by:
Vasyl Gomonovych <gomonovych@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Stanimir Varbanov authored
Move ptype (property type) initialization out of switch case and save few lines of code. Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
-
Geert Uytterhoeven authored
As of_node_full_name() now returns only the basename, the endpoint information printed became useless: adv748x 4-0070: Endpoint endpoint on port 7 adv748x 4-0070: Endpoint endpoint on port 8 adv748x 4-0070: Endpoint endpoint on port 10 adv748x 4-0070: Endpoint endpoint on port 11 Restore the old behavior by using "%pOF" instead: adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7 adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8 adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10 adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11 Fixes: a7e4cfb0 ("of/fdt: only store the device node basename in full_name") Signed-off-by:Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Arnd Bergmann authored
timespec is generally deprecated because of the y2038 overflow. In vivid, the usage is fine, since we are dealing with monotonic timestamps, but we can also simplify the code by going to ktime_t. Using ktime_divns() should be roughly as efficient as the old code, since the constant 64-bit division gets turned into a multiplication on modern platforms, and we save multiple 32-bit divisions that can be expensive e.g. on ARMv7. Tested-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
The imx media driver passes around monotonic timestamps in the deprecated 'timespec' format. This is not a problem for the driver, as they won't overflow, but moving to either timespec64 or ktime_t is preferred. I'm picking ktime_t for simplicity here. frame_interval_monitor() is the main function that changes, as it tries to compare a time interval in microseconds. The algorithm slightly changes here, to avoid 64-bit division. The code previously assumed that the error was at most 32-bit worth of microseconds here, so I'm making the same assumption but add an explicit test for it. Signed-off-by:
-
