A single Ri mismatch doesn't automatically mean that the link integrity
is broken. Update and check of Ri and Ri' are done asynchronously. In
case an update happens just between the read of Ri' and the check against
Ri there will be a mismatch even if the link integrity is fine otherwise.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504123524.7731-1-oliver.barta@aptiv.com

The linetime watermark is a 9 bit value, which gives us
a maximum linetime of just below 64 usec. If the linetime
exceeds that value we currently just discard the high bits
and program the rest into the register, which angers the
state checker.

To avoid that let's just clamp the value to the max. I believe
it should be perfectly fine to program a smaller linetime wm
than strictly required, just means the hardware may fetch data
sooner than strictly needed. We are further reassured by the
fact that with DRRS the spec tells us to program the smaller
of the two linetimes corresponding to the two refresh rates.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625200003.12436-1-ville.syrjala@linux.intel.comReviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Update code to reflect recent bspec changes

Bspec: 52890
Bspec: 53508
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200624215723.2316-1-matthew.s.atwood@intel.com

This workaround now also applies to TGL and RKL, so extend the PCH test
to just capture everthing ICP and beyond.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617180006.4130501-1-matthew.d.roper@intel.comReviewed-by: Matt Atwood <matthew.s.atwood@intel.com>

The DP spec says:
"The transmitter shall support at least three levels of voltage
 swing (Levels 0, 1, and 2).

 If only three levels of voltage swing are supported (VOLTAGE
 SWING SET field (bits 1:0) are programmed to 10 (Level 2)),
 this bit shall be set to 1, and cleared in all other cases.

 If all four levels of voltage swing are supported (VOLTAGE
 SWING SET field (bits 1:0) are programmed to 11 (Level 3)),
 this bit shall be set to 1,and cleared in all other cases."

Let's follow that exactly instead of the current apporach
where we can set those also for vswing/preemph levels 0 or 1
(or 2 when the platform max is 3).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-7-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>

Catch up with upstream, in particular to get c1e8d7c6 ("mmap locking
API: convert mmap_sem comments").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com

drm-misc-next for v5.9:

UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.

Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.

Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
  - Remove gem_free_object()
  - Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.

Driver Changes:
 Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE  Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com

During encoder enabling we clear the flag before starting the ACT
sequence and wait for the flag, but the clearing is missing during
encoder disabling, add it there too. Since nothing cleared the flag
automatically we could've run subsequent disabling steps too early.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-5-imre.deak@intel.com

It's not clear if the DP_TP_STATUS flags other than the ACT sent flag
have some side-effect, so don't clear those; we don't depend on the
state of these flags anyway.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-4-imre.deak@intel.com

During transcoder enabling we'll configure the transcoder in MST mode
and enable the VC payload allocation, which will start the ACT sequence.
Before waiting for the ACT sequence completion, we need to clear the ACT
sent flag, but based on the above we can do this right before enabling
the transcoder.

For clarity, move the flag clearing closer to where we wait for it.

While at it also factor out some common code.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-3-imre.deak@intel.com

During the initial probing of an MST sink, MST core will determine the
sink's link bandwidth based on its own version of the sink link
rate/lane count caps it reads from the DPCD. At a later point (after
probing and 1 or more modesets) i915 may limit the link parameters wrt.
the original source/sink common caps above due to link training failures
during a modeset and the resulting link training fallback logic.

Based on the above a modeset following another modeset with a link
training error will compute the i915 HW specific and DP protocol timing
parameters (data/link M/N and MST TU values) taking into account only
the unlimited source/sink common caps, but not taking into account the
fallback limits. This will also let DRM core oversubscribe the actual
link bandwidth during the MST payload allocation.

Prevent the above problem by disabling the link training fallback on MST
links for now, until the MST probe time initialization and the MST
compute config logic can deal with changing link parameters.

The misconfigured timings lead at least to a
'Timed out waiting for DP idle patterns'
error.

v2: (Ville)
- Print link training error message on the MST path too.
- Clarify the problem in the commit log.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-2-imre.deak@intel.com

MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.

One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a

'Timed out waiting for ACT sent when disabling'

error, due to reading from the incorrect DP_TP_STATUS register.

This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.

v2:
- Correct the failure scenario in the commit log. (José)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com

Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.

The stragglers are:

* i915.force_probe and i915.modeset. Needed before dev_priv is
  available. This is fine because the parameters are read-only and never
  modified.

* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
  I915_STATE_WARN_ON would result in massive and ugly churn. This is
  handled by not exposing the parameter via debugfs, and leaving the
  parameter writable in sysfs. This may be fixed up in follow-up work.

* i915.inject_probe_failure. Only makes sense in terms of the module,
  not the device. This is handled by not exposing the parameter via
  debugfs.

v2: Fix uc i915 lookup code (Michał Winiarski)

Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com

Pull SELinux fixes from Paul Moore:
 "Three small patches to fix problems in the SELinux code, all found via
  clang.

  Two patches fix potential double-free conditions and one fixes an
  undefined return value"

* tag 'selinux-pr-20200621' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: fix undefined return of cond_evaluate_expr
  selinux: fix a double free in cond_read_node()/cond_read_list()
  selinux: fix double free

Pull pin control fixes from Linus Walleij:
 "Some early fixes collected during the first week after the merge
  window, all pretty self-evident, with the details below. The revert is
  the crucial thing.

   - Fix a warning on the Qualcomm SPMI GPIO chip being instatiated
     twice without a unique irqchip struct

   - Use the noirq variants of the suspend and resume callbacks in the
     Tegra driver

   - Clean up the errorpath on the MCP23s08 driver

   - Revert the use of devm_of_iomap() in the Freescale driver as it was
     regressing the platform

   - Add some missing pins in the Qualcomm IPQ6018 driver

   - Fix a simple documentation bug in the pinctrl-single driver"

* tag 'pinctrl-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: single: fix function name in documentation
  pinctrl: qcom: ipq6018 Add missing pins in qpic pin group
  Revert "pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'"
  pinctrl: mcp23s08: Split to three parts: fix ptr_ret.cocci warnings
  pinctrl: tegra: Use noirq suspend/resume callbacks
  pinctrl: qcom: spmi-gpio: fix warning about irq chip reusage

Merge tag 'kbuild-fixes-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix -gz=zlib compiler option test for CONFIG_DEBUG_INFO_COMPRESSED

 - improve cc-option in scripts/Kbuild.include to clean up temp files

 - improve cc-option in scripts/Kconfig.include for more reliable
   compile option test

 - do not copy modules.builtin by 'make install' because it would break
   existing systems

 - use 'userprogs' syntax for watch_queue sample

* tag 'kbuild-fixes-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  samples: watch_queue: build sample program for target architecture
  Revert "Makefile: install modules.builtin even if CONFIG_MODULES=n"
  scripts: Fix typo in headers_install.sh
  kconfig: unify cc-option and as-option
  kbuild: improve cc-option to clean up all temporary files
  Makefile: Improve compressed debug info support detection

Pull powerpc fixes from Michael Ellerman:

 - One fix for the interrupt rework we did last release which broke
   KVM-PR

 - Three commits fixing some fallout from the READ_ONCE() changes
   interacting badly with our 8xx 16K pages support, which uses a pte_t
   that is a structure of 4 actual PTEs

 - A cleanup of the 8xx pte_update() to use the newly added pmd_off()

 - A fix for a crash when handling an oops if CONFIG_DEBUG_VIRTUAL is
   enabled

 - A minor fix for the SPU syscall generation

Thanks to Aneesh Kumar K.V, Christian Zigotzky, Christophe Leroy, Mike
Rapoport, Nicholas Piggin.

* tag 'powerpc-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/8xx: Provide ptep_get() with 16k pages
  mm: Allow arches to provide ptep_get()
  mm/gup: Use huge_ptep_get() in gup_hugepte()
  powerpc/syscalls: Use the number when building SPU syscall table
  powerpc/8xx: use pmd_off() to access a PMD entry in pte_update()
  powerpc/64s: Fix KVM interrupt using wrong save area
  powerpc: Fix kernel crash in show_instructions() w/DEBUG_VIRTUAL

Pull crypto fixes from Herbert Xu:

 - NULL dereference in octeontx

 - PM reference imbalance in ks-sa

 - deadlock in crypto manager

 - memory leak in drbg

 - missing socket limit check on receive SG list size in algif_skcipher

 - typos in caam

 - warnings in ccp and hisilicon

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: drbg - always try to free Jitter RNG instance
  crypto: marvell/octeontx - Fix a potential NULL dereference
  crypto: algboss - don't wait during notifier callback
  crypto: caam - fix typos
  crypto: ccp - Fix sparse warnings in sev-dev
  crypto: hisilicon - Cap block size at 2^31
  crypto: algif_skcipher - Cap recv SG list at ctx->used
  hwrng: ks-sa - Fix runtime PM imbalance on error

This userspace program includes UAPI headers exported to usr/include/.
'make headers' always works for the target architecture (i.e. the same
architecture as the kernel), so the sample program should be built for
the target as well. Kbuild now supports 'userprogs' for that.

I also guarded the CONFIG option by 'depends on CC_CAN_LINK' because
$(CC) may not provide libc.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

This reverts commit e0b250b5,
which broke build systems that need to install files to a certain
path, but do not set INSTALL_MOD_PATH when invoking 'make install'.

  $ make INSTALL_PATH=/tmp/destdir install
  mkdir: cannot create directory ‘/lib/modules/5.8.0-rc1+/’: Permission denied
  Makefile:1342: recipe for target '_builtin_inst_' failed
  make: *** [_builtin_inst_] Error 1

While modules.builtin is useful also for CONFIG_MODULES=n, this change
in the behavior is quite unexpected. Maybe "make modules_install"
can install modules.builtin irrespective of CONFIG_MODULES as Jonas
originally suggested.

Anyway, that commit should be reverted ASAP.
Reported-by: Douglas Anderson <dianders@chromium.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>

Pull SCSI fixes from James Bottomley:
 "One minor fix and two patches reworking the ata dma drain for the
  !CONFIG_LIBATA case. The latter is a 5.7 regression fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Wire up ata_scsi_dma_need_drain for SAS HBA drivers
  scsi: libata: Provide an ata_scsi_dma_need_drain stub for !CONFIG_ATA
  scsi: ufs-bsg: Fix runtime PM imbalance on error

Pull i2c fixes from Wolfram Sang:

 - a small collection of remaining API conversion patches (all acked)
   which allow to finally remove the deprecated API

 - some documentation fixes and a MAINTAINERS addition

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Add robert and myself as qcom i2c cci maintainers
  i2c: smbus: Fix spelling mistake in the comments
  Documentation/i2c: SMBus start signal is S not A
  i2c: remove deprecated i2c_new_device API
  Documentation: media: convert to use i2c_new_client_device()
  video: backlight: tosa_lcd: convert to use i2c_new_client_device()
  x86/platform/intel-mid: convert to use i2c_new_client_device()
  drm: encoder_slave: use new I2C API
  drm: encoder_slave: fix refcouting error for modules

Use the correct the function name in the documentation for
"pcs_parse_one_pinctrl_entry()".

"smux_parse_one_pinctrl_entry()" appears to be an artifact from the
development of a prior patch series ("simple pinmux driver") which
transformed into pinctrl-single.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20200612112758.GA3407886@x1Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull tracing fixes from Steven Rostedt:

 - Have recordmcount work with > 64K sections (to support LTO)

 - kprobe RCU fixes

 - Correct a kprobe critical section with missing mutex

 - Remove redundant arch_disarm_kprobe() call

 - Fix lockup when kretprobe triggers within kprobe_flush_task()

 - Fix memory leak in fetch_op_data operations

 - Fix sleep in atomic in ftrace trace array sample code

 - Free up memory on failure in sample trace array code

 - Fix incorrect reporting of function_graph fields in format file

 - Fix quote within quote parsing in bootconfig

 - Fix return value of bootconfig tool

 - Add testcases for bootconfig tool

 - Fix maybe uninitialized warning in ftrace pid file code

 - Remove unused variable in tracing_iter_reset()

 - Fix some typos

* tag 'trace-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix maybe-uninitialized compiler warning
  tools/bootconfig: Add testcase for show-command and quotes test
  tools/bootconfig: Fix to return 0 if succeeded to show the bootconfig
  tools/bootconfig: Fix to use correct quotes for value
  proc/bootconfig: Fix to use correct quotes for value
  tracing: Remove unused event variable in tracing_iter_reset
  tracing/probe: Fix memleak in fetch_op_data operations
  trace: Fix typo in allocate_ftrace_ops()'s comment
  tracing: Make ftrace packed events have align of 1
  sample-trace-array: Remove trace_array 'sample-instance'
  sample-trace-array: Fix sleeping function called from invalid context
  kretprobe: Prevent triggering kretprobe from within kprobe_flush_task
  kprobes: Remove redundant arch_disarm_kprobe() call
  kprobes: Fix to protect kick_kprobe_optimizer() by kprobe_mutex
  kprobes: Use non RCU traversal APIs on kprobe_tables if possible
  kprobes: Suppress the suspicious RCU warning on kprobes
  recordmcount: support >64k sections

Pull libnvdimm updates from Dan Williams:
 "A feature (papr_scm health retrieval) and a fix (sysfs attribute
  visibility) for v5.8.

  Vaibhav explains in the merge commit below why missing v5.8 would be
  painful and I agreed to try a -rc2 pull because only cosmetics kept
  this out of -rc1 and his initial versions were posted in more than
  enough time for v5.8 consideration:

   'These patches are tied to specific features that were committed to
    customers in upcoming distros releases (RHEL and SLES) whose
    time-lines are tied to 5.8 kernel release.

    Being able to track the health of an nvdimm is critical for our
    customers that are running workloads leveraging papr-scm nvdimms.
    Missing the 5.8 kernel would mean missing the distro timelines and
    shifting forward the availability of this feature in distro kernels
    by at least 6 months'

  Summary:

   - Fix the visibility of the region 'align' attribute.

     The new unit tests for region alignment handling caught a corner
     case where the alignment cannot be specified if the region is
     converted from static to dynamic provisioning at runtime.

   - Add support for device health retrieval for the persistent memory
     supported by the papr_scm driver.

     This includes both the standard sysfs "health flags" that the nfit
     persistent memory driver publishes and a mechanism for the ndctl
     tool to retrieve a health-command payload"

* tag 'libnvdimm-for-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nvdimm/region: always show the 'align' attribute
  powerpc/papr_scm: Implement support for PAPR_PDSM_HEALTH
  ndctl/papr_scm,uapi: Add support for PAPR nvdimm specific methods
  powerpc/papr_scm: Improve error logging and handling papr_scm_ndctl()
  powerpc/papr_scm: Fetch nvdimm health information from PHYP
  seq_buf: Export seq_buf_printf
  powerpc: Document details on H_SCM_HEALTH hcall

The patch adds missing qpic data pins to qpic pingroup. These pins are
necessary for the qpic nand to work.

Fixes: ef1ea54e ("pinctrl: qcom: Add ipq6018 pinctrl driver")
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1592541089-17700-1-git-send-email-sivaprak@codeaurora.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Revert "pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'"

This reverts commit ba403242.

After commit 26d8cde5 ("pinctrl: freescale: imx: add shared
input select reg support"). i.MX7D has two iomux controllers
iomuxc and iomuxc-lpsr which share select_input register for
daisy chain settings.
If use 'devm_of_iomap()', when probe the iomuxc-lpsr, will call
devm_request_mem_region() for the region <0x30330000-0x3033ffff>
for the first time. Then, next time when probe the iomuxc, API
devm_platform_ioremap_resource() will also use the API
devm_request_mem_region() for the share region <0x30330000-0x3033ffff>
again, then cause issue, log like below:

[    0.179561] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
[    0.191742] imx7d-pinctrl 30330000.pinctrl: can't request region for resource [mem 0x30330000-0x3033ffff]
[    0.191842] imx7d-pinctrl: probe of 30330000.pinctrl failed with error -16

Fixes: ba403242 ("pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1591673223-1680-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull s390 fixes from Vasily Gorbik:

 - a few ptrace fixes mostly for strace and seccomp_bpf kernel tests
   findings

 - cleanup unused pm callbacks in virtio ccw

 - replace kmalloc + memset with kzalloc in crypto

 - use $(LD) for vDSO linkage to make clang happy

 - fix vDSO clock_getres() to preserve the same behaviour as
   posix_get_hrtimer_res()

 - fix workqueue cpumask warning when NUMA=n and nr_node_ids=2

 - reduce SLSB writes during input processing, improve warnings and
   cleanup qdio_data usage in qdio

 - a few fixes to use scnprintf() instead of snprintf()

* tag 's390-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: fix syscall_get_error for compat processes
  s390/qdio: warn about unexpected SLSB states
  s390/qdio: clean up usage of qdio_data
  s390/numa: let NODES_SHIFT depend on NEED_MULTIPLE_NODES
  s390/vdso: fix vDSO clock_getres()
  s390/vdso: Use $(LD) instead of $(CC) to link vDSO
  s390/protvirt: use scnprintf() instead of snprintf()
  s390: use scnprintf() in sys_##_prefix##_##_name##_show
  s390/crypto: use scnprintf() instead of snprintf()
  s390/zcrypt: use kzalloc
  s390/virtio: remove unused pm callbacks
  s390/qdio: reduce SLSB writes during Input Queue processing
  selftests/seccomp: s390 shares the syscall and return value register
  s390/ptrace: fix setting syscall number
  s390/ptrace: pass invalid syscall numbers to tracing
  s390/ptrace: return -ENOSYS when invalid syscall is supplied
  s390/seccomp: pass syscall arguments via seccomp_data
  s390/qdio: fine-tune SLSB update

Pull RISC-V fixes from Palmer Dabbelt:

 - a workaround for a compiler surprise related to the "r" inline
   assembly that allows LLVM to boot.

 - a fix to avoid WX-only mappings, which the ISA does not allow. While
   this probably manifests in many ways, the bug was found in stress-ng.

 - a missing lock in set_direct_map_*(), which due to a recent lockdep
   change started asserting.

* tag 'riscv-for-linus-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Acquire mmap lock before invoking walk_page_range
  RISC-V: Don't allow write+exec only page mapping request in mmap
  riscv/atomic: Fix sign extension for RV64I

Merge tag 'linux-kselftest-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest cleanups from Shuah Khan:

 - ftrace "requires:" list for simplifying and unifying requirement
   checks for each test case, adding "requires:" line instead of
   checking required ftrace interfaces in each test case.

 - a minor spelling correction patch

* tag 'linux-kselftest-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/ftrace: Support ":README" suffix for requires
  selftests/ftrace: Support ":tracer" suffix for requires
  selftests/ftrace: Convert check_filter_file() with requires list
  selftests/ftrace: Convert required interface checks into requires list
  selftests/ftrace: Add "requires:" list support
  selftests/ftrace: Return unsupported for the unconfigured features
  selftests/ftrace: Allow ":" in description
  tools: testing: ftrace: trigger: fix spelling mistake

The fileserver probe timer, net->fs_probe_timer, isn't cancelled when
the kafs module is being removed and so the count it holds on
net->servers_outstanding doesn't get dropped..

This causes rmmod to wait forever.  The hung process shows a stack like:

	afs_purge_servers+0x1b5/0x23c [kafs]
	afs_net_exit+0x44/0x6e [kafs]
	ops_exit_list+0x72/0x93
	unregister_pernet_operations+0x14c/0x1ba
	unregister_pernet_subsys+0x1d/0x2a
	afs_exit+0x29/0x6f [kafs]
	__do_sys_delete_module.isra.0+0x1a2/0x24b
	do_syscall_64+0x51/0x95
	entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fix this by:

 (1) Attempting to cancel the probe timer and, if successful, drop the
     count that the timer was holding.

 (2) Make the timer function just drop the count and not schedule the
     prober if the afs portion of net namespace is being destroyed.

Also, whilst we're at it, make the following changes:

 (3) Initialise net->servers_outstanding to 1 and decrement it before
     waiting on it so that it doesn't generate wake up events by being
     decremented to 0 until we're cleaning up.

 (4) Switch the atomic_dec() on ->servers_outstanding for ->fs_timer in
     afs_purge_servers() to use the helper function for that.

Fixes: f6cbb368 ("afs: Actively poll fileservers to maintain NAT or firewall openings")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix afs_do_lookup()'s fallback case for when FS.InlineBulkStatus isn't
supported by the server.

In the fallback, it calls FS.FetchStatus for the specific vnode it's
meant to be looking up.  Commit b6489a49 broke this by renaming one
of the two identically-named afs_fetch_status_operation descriptors to
something else so that one of them could be made non-static.  The site
that used the renamed one, however, wasn't renamed and didn't produce
any warning because the other was declared in a header.

Fix this by making afs_do_lookup() use the renamed variant.

Note that there are two variants of the success method because one is
called from ->lookup() where we may or may not have an inode, but can't
call iget until after we've talked to the server - whereas the other is
called from within iget where we have an inode, but it may or may not be
initialised.

The latter variant expects there to be an inode, but because it's being
called from there former case, there might not be - resulting in an oops
like the following:

  BUG: kernel NULL pointer dereference, address: 00000000000000b0
  ...
  RIP: 0010:afs_fetch_status_success+0x27/0x7e
  ...
  Call Trace:
    afs_wait_for_operation+0xda/0x234
    afs_do_lookup+0x2fe/0x3c1
    afs_lookup+0x3c5/0x4bd
    __lookup_slow+0xcd/0x10f
    walk_component+0xa2/0x10c
    path_lookupat.isra.0+0x80/0x110
    filename_lookup+0x81/0x104
    vfs_statx+0x76/0x109
    __do_sys_newlstat+0x39/0x6b
    do_syscall_64+0x4c/0x78
    entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: b6489a49 ("afs: Fix silly rename")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

READ_ONCE() now enforces atomic read, which leads to:

  CC      mm/gup.o
In file included from ./include/linux/kernel.h:11:0,
                 from mm/gup.c:2:
In function 'gup_hugepte.constprop',
    inlined from 'gup_huge_pd.isra.79' at mm/gup.c:2465:8:
./include/linux/compiler.h:392:38: error: call to '__compiletime_assert_222' declared with attribute error: Unsupported access size for {READ,WRITE}_ONCE().
  _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
                                      ^
./include/linux/compiler.h:373:4: note: in definition of macro '__compiletime_assert'
    prefix ## suffix();    \
    ^
./include/linux/compiler.h:392:2: note: in expansion of macro '_compiletime_assert'
  _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
  ^
./include/linux/compiler.h:405:2: note: in expansion of macro 'compiletime_assert'
  compiletime_assert(__native_word(t) || sizeof(t) == sizeof(long long), \
  ^
./include/linux/compiler.h:291:2: note: in expansion of macro 'compiletime_assert_rwonce_type'
  compiletime_assert_rwonce_type(x);    \
  ^
mm/gup.c:2428:8: note: in expansion of macro 'READ_ONCE'
  pte = READ_ONCE(*ptep);
        ^
In function 'gup_get_pte',
    inlined from 'gup_pte_range' at mm/gup.c:2228:9,
    inlined from 'gup_pmd_range' at mm/gup.c:2613:15,
    inlined from 'gup_pud_range' at mm/gup.c:2641:15,
    inlined from 'gup_p4d_range' at mm/gup.c:2666:15,
    inlined from 'gup_pgd_range' at mm/gup.c:2694:15,
    inlined from 'internal_get_user_pages_fast' at mm/gup.c:2795:3:
./include/linux/compiler.h:392:38: error: call to '__compiletime_assert_219' declared with attribute error: Unsupported access size for {READ,WRITE}_ONCE().
  _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
                                      ^
./include/linux/compiler.h:373:4: note: in definition of macro '__compiletime_assert'
    prefix ## suffix();    \
    ^
./include/linux/compiler.h:392:2: note: in expansion of macro '_compiletime_assert'
  _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
  ^
./include/linux/compiler.h:405:2: note: in expansion of macro 'compiletime_assert'
  compiletime_assert(__native_word(t) || sizeof(t) == sizeof(long long), \
  ^
./include/linux/compiler.h:291:2: note: in expansion of macro 'compiletime_assert_rwonce_type'
  compiletime_assert_rwonce_type(x);    \
  ^
mm/gup.c:2199:9: note: in expansion of macro 'READ_ONCE'
  return READ_ONCE(*ptep);
         ^
make[2]: *** [mm/gup.o] Error 1

Define ptep_get() on 8xx when using 16k pages.

Fixes: 9e343b46 ("READ_ONCE: Enforce atomicity for {READ,WRITE}_ONCE() memory accesses")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/341688399c1b102756046d19ea6ce39db1ae4742.1592225558.git.christophe.leroy@csgroup.eu

Since commit 9e343b46 ("READ_ONCE: Enforce atomicity for
{READ,WRITE}_ONCE() memory accesses") it is not possible anymore to
use READ_ONCE() to access complex page table entries like the one
defined for powerpc 8xx with 16k size pages.

Define a ptep_get() helper that architectures can override instead
of performing a READ_ONCE() on the page table entry pointer.

Fixes: 9e343b46 ("READ_ONCE: Enforce atomicity for {READ,WRITE}_ONCE() memory accesses")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/087fa12b6e920e32315136b998aa834f99242695.1592225558.git.christophe.leroy@csgroup.eu

gup_hugepte() reads hugepage table entries, it can't read
them directly, huge_ptep_get() must be used.

Fixes: 9e343b46 ("READ_ONCE: Enforce atomicity for {READ,WRITE}_ONCE() memory accesses")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ffc3714334c3bfaca6f13788ad039e8759ae413f.1592225558.git.christophe.leroy@csgroup.eu

We only emit the renderstate once now during module load, it is no
longer a concern that we are delaying context creation and so do not
need to so eagerly optimise. Since the last time we have looked at the
renderstate, we have a pin_map / flush_map facility that supports simple
single mappings, replacing the open-coded kmap_atomic() and
prepare_write. As it should be a single page, of which we only write a
small portion, we stick to a simple WB [kmap] and use clflush on !llc
platforms, rather than creating a temporary WC vmapping for the single
page.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619234543.17499-2-chris@chris-wilson.co.uk

Since gvt calls pin_map for the shadow batch buffer, this makes the
action of prepare_write [+pin_pages] redundant. We can write into the
obj->mm.mapping directory and the flush_map routine knows when it has to
flush the cpu cache afterwards.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619234543.17499-1-chris@chris-wilson.co.uk

Include the papr_scm health retrieval feature for v5.8-rc2. The
functionality was initially posted well in advance of the merge window,
but review comments and a late build-bot warning kept them out of the
v5.8-rc1 libnvdimm pull request.

Vaibhav notes:
These patches are tied to specific features that were committed to
customers in upcoming distros releases (RHEL and SLES) whose time-lines
are tied to 5.8 kernel release.

Being able to track the health of an nvdimm is critical for our
customers that are running workloads leveraging papr-scm nvdimms.
Missing the 5.8 kernel would mean missing the distro timelines and
shifting forward the availability of this feature in distro kernels by
at least 6 months.