Allow gpio-fan to be used as thermal cooling device for platforms that
use GPIO maps to control fans.

As part of this change, we make the shutdown and remove logic the same
as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The PWM FAN device can now be used as a thermal cooling device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch provides code for reading PWM FAN configuration data via
device tree. The pwm-fan can work with full speed when configuration
is not provided. However, errors are propagated when wrong DT bindings
are found.
Additionally the struct pwm_fan_ctx has been extended.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

It was necessary to decouple code handling writing to sysfs from the one
responsible for setting PWM of the fan.
Due to that, new __set_pwm() method was extracted, which is responsible for
only setting new PWM duty cycle.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

On some boards, such as the LaCie 2Big Network v2 or 2Big NAS (based on
Marvell Kirkwood SoCs), an I2C fan controller is used but the alarm
signal is wired to a separate GPIO. Unfortunately, the gpio-fan driver
can't be used to handle GPIO alarm alone from DT: an error is returned
if the "gpios" DT property is missing.

This patch allows to use the gpio-fan driver even if the "alarm-gpios"
DT property is defined alone.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The bank register has five unused bits. Verify that those bits are zero
to strengthen the detect function.

Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>

The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

IT8603 only supports three fans, so it is not necessary to skip fan4.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Newer chips don't typically support VID inputs or control.
Add a feature flag for VID support to simplify adding support for
new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Fans 4-5 are not supported on all chips and revisions. Also, 16-bit fan
counters are always enabled on some chips. Provide feature flags to
simplify adding support for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

On IT8728F, IT8771E, and IT8772E, fans counters are always 16 bit
and don't need to be configured for it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.

Also add support for TS3001 and TSE2004.

Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The only difference between the three power_sensor_name_templates is
whether there is a suffix of "", "_lowest" or "_highest". We might as
well pull those into an array and use a literal format string,
allowing gcc to do type checking of the arguments to
sprintf. Incidentially, the same three suffixes are used in the
temp_sensor_name_templates case, so we end up eliminating one static
array.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: Fixed line length over 80 characters]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

By extracting the only part that differs we can allow static checking
of the format string, and possibly save a little .rodata.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull USB fixes from Greg KH:
 "Here's a round of USB fixes for 4.0-rc3.

  Nothing major, the usual gadget, xhci and usb-serial fixes and a few
  new device ids as well.

  All have been in linux-next successfully"

* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
  xhci: Workaround for PME stuck issues in Intel xhci
  xhci: fix reporting of 0-sized URBs in control endpoint
  usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
  USB: ch341: set tty baud speed according to tty struct
  USB: serial: cp210x: Adding Seletek device id's
  USB: pl2303: disable break on shutdown
  USB: mxuport: fix null deref when used as a console
  USB: serial: clean up bus probe error handling
  USB: serial: fix port attribute-creation race
  USB: serial: fix tty-device error handling at probe
  USB: serial: fix potential use-after-free after failed probe
  USB: console: add dummy __module_get
  USB: ftdi_sio: add PIDs for Actisense USB devices
  Revert "USB: serial: make bulk_out_size a lower limit"
  cdc-acm: Add support for Denso cradle CU-321
  usb-storage: support for more than 8 LUNs
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
  USB: usbfs: don't leak kernel data in siginfo
  xhci: Clear the host side toggle manually when endpoint is 'soft reset'
  xhci: Allocate correct amount of scratchpad buffers
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.0-rc3.

  Along with the atime fix that you know about, here are some other
  serial driver bugfixes as well.  Most notable is a wait_until_sent
  bugfix that was traced back to being around since before 2.6.12 that
  Johan has fixed up.

  All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  TTY: fix tty_wait_until_sent maximum timeout
  TTY: fix tty_wait_until_sent on 64-bit machines
  USB: serial: fix infinite wait_until_sent timeout
  TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
  net: irda: fix wait_until_sent poll timeout
  serial: uapi: Declare all userspace-visible io types
  serial: core: Fix iotype userspace breakage
  serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
  console: Fix console name size mismatch
  tty: fix up atime/mtime mess, take four
  serial: 8250_dw: Fix get_mctrl behaviour
  serial:8250:8250_pci: delete unneeded quirk entries
  serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
  Change email address for 8250_pci
  serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
  Revert "tty/serial: of_serial: add DT alias ID handling"

Pull staging driver fixes from Greg KH:
 "Here are some IIO and staging driver fixes for 4.0-rc3.

  Details are in the shortlog, nothing major, mostly IIO fixes for
  reported issues.

  All have been in linux-next successfully"

* tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel
  staging: comedi: vmk80xx: remove "firmware version" kernel messages
  staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample()
  iio: ak8975: fix AK09911 dependencies
  iio: common: ssp_sensors: Protect PM-only functions to kill warning
  IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc
  Revert "iio:humidity:si7020: fix pointer to i2c client"
  iio: light: gp2ap020a00f: Select REGMAP_I2C
  iio: light: jsa1212: Select REGMAP_I2C
  iio: ad5686: fix optional reference voltage declaration
  iio:adc:mcp3422 Fix incorrect scales table
  iio: mxs-lradc: fix iio channel map regression
  iio: imu: adis16400: Fix sign extension
  staging: iio: ad2s1200: Fix sign extension
  iio: mxs-lradc: only update the buffer when its conversions have finished
  iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions
  iio: mxs-lradc: make ADC reads not disable touchscreen interrupts
  iio: mxs-lradc: separate touchscreen and buffer virtual channels
  iio: imu: inv_mpu6050: Prevent dereferencing NULL
  iio: iadc: wait_for_completion_timeout time in jiffies
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are two char/misc fixes for 4.0-rc3.

  One is a reported binder driver fix needed due to a change in the mm
  core that happened in 4.0-rc1.  Another is a mei driver fix that
  resolves a reported issue in that driver.

  Both have been in linux-next for a while"

* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: make device disabled on stop unconditionally
  android: binder: fix binder mmap failures

Pull "code of conflict" from Greg KH:
 "This file tries to set the rational basis for our code reviews, gives
  some advice on how to conduct them, and provides an excalation channel
  for any kernel developers if they so desire it"

[ Let's see how this works ]

* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Code of Conflict

Pull i2c fixes from Wolfram Sang:
 "A set of updates and bugfixes for the new designware-baytrail driver.

  And a documentation bugfix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: add required clocks property to binding
  i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
  i2c: designware-baytrail: cross-check lock functions
  i2c: designware-baytrail: fix sparse warnings
  i2c: designware-baytrail: fix typo in error path
  i2c: designware-baytrail: describe magic numbers

Pull slave-dmaengine fixes from Vinod Koul:
 "This contains small fixes spread across the drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mmp_pdma: fix warning about slave caps
  dmaengine: qcom_bam_dma: fix wrong register offsets
  dmaengine: bam-dma: fix a warning about missing capabilities
  dmaengine: ioatdma: workaround for incorrect DMACAP register
  dmaengine: at_xdmac: fix for chan conf simplification
  dmaengine: dw: don't handle interrupt when dmaengine is not used
  dma: mmp-tdma: refine dma disable and dma-pos update
  dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks
  dmaenegine: mmp-pdma: fix irq handler overwrite physical chan issue

Pull arm64 fixes from Catalin Marinas:
 "arm64 and generic kernel/module.c (acked by Rusty) fixes for
  CONFIG_DEBUG_SET_MODULE_RONX"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kernel/module.c: Update debug alignment after symtable generation
  arm64: Don't use is_module_addr in setting page attributes

Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.

Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.

Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.

This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.

The first symptom  was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.

Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.

Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to handle an infinite timeout (0).

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: dcf01050 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org>	# v3.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In case an infinite timeout (0) is requested, the irda wait_until_sent
implementation would use a zero poll timeout rather than the default
200ms.

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.

Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3ffb1a81 ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.

Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6ae9200f ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.

Cc: <stable@vger.kernel.org> # 2.6.22+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This problem was taken care of three times already in
* b0de59b5 (TTY: do not update
  atime/mtime on read/write),
* 37b7f3c7 (TTY: fix atime/mtime
  regression), and
* b0b88565 (tty: fix up atime/mtime
  mess, take three)

But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.

So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.

Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com>
Cc: <stable@vger.kernel.org> # all, as b0b88565 was backported
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver

Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.

It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These quirk entries have the same effect as default
quirk entry, so we can just delete them.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 8b5c913f
("serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection")
trigger one redundant entry report message.

This patch fix it.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.

Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>