Go to existing error handling code at the end of the function that calls
clk_put.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, user-space cannot determine if a 0 tcp_vlan_tci
means there is no VLAN tag or the VLAN ID was zero.

Add flag to make this explicit.  User-space can check for
TP_STATUS_VLAN_VALID || tp_vlan_tci > 0, which will be backwards
compatible. Older could would have just checked for tp_vlan_tci,
so it will work no worse than before.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take the RTNL lock unconditionally when calling dev_close.
Taking the lock conditionally may cause race conditions.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This avoids messages like this after suspend:

   cdc_ncm 2-1.4:1.6: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.7: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.6: usb0: unregister 'cdc_ncm' usb-0000:00:1d.0-1.4, CDC NCM

This is important for the Ericsson F5521gw GSM/UMTS modem.
Otherwise modemmanager looses the fact that the cdc_ncm and cdc_acm devices
belong together.

The cdc_ether module does the same.
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 4af429d2 (vlan: lockless
transmit path) have a typo in vlan_dev_hard_start_xmit(), using
u64_stats_update_begin() to end the stat update, it should be
u64_stats_update_end().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check against mistakenly passing in IPv6 addresses (which would result
in an INADDR_ANY bind) or similar incompatible sockaddrs.
Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit e5cb966c.

It causes new build regressions with gcc-4.2 which is
pretty common on non-x86 platforms.
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

catc_ctrl_run() calls usb_submit_urb() with GFP_KERNEL, while it is called from
catc_ctrl_async() and catc_ctrl_done() with catc->ctrl_lock spinlock held.

The patch replaces GFP_KERNEL with GFP_ATOMIC.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the peer restart the asoc, we should not only fail any unsent/unacked
data, but also stop the T3-rtx, SACK, T4-rto timers, and teardown ASCONF
queues.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a driver crash during packet reception due to not enough
bytes allocated in the skb. Since the loop reads out 4 bytes at a time, we
need to allow for up to 3 bytes of slack space.
Signed-off-by: Dennis Aberilla <denzzzhome@yahoo.com>
Signed-off-by: David S. Miller <davem@zippy.davemloft.net>

The current code takes an unaligned pointer and does htonl() on it to
make it big-endian, then does a memcpy().  The problem is that the
compiler decides that since the pointer is to a __be32, it is legal
to optimize the copy into a processor word store.  However, on an
architecture that does not handled unaligned writes in kernel space,
this produces an unaligned exception fault.

The solution is to track the pointer as a "char *" (which removes a bunch
of unpleasant casts in any case), and then just use put_unaligned_be32()
to write the value to memory.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@zippy.davemloft.net>

Ingo Molnar noticed that we have this unnecessary ratelimit.h
dependency in linux/net.h, which hid compilation problems from
people doing builds only with CONFIG_NET enabled.

Move this stuff out to a seperate net/net_ratelimit.h file and
include that in the only two places where this thing is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>

Several networking headers were depending upon the implicit
linux/sysctl.h include they get when including linux/net.h

Add explicit includes.
Signed-off-by: David S. Miller <davem@davemloft.net>

This got missed back in 2006 when Jes Sorensen deleted
net/ethernet/sysctl_net_ether.c
Signed-off-by: David S. Miller <davem@davemloft.net>

Several crashes in cleanup_once() were reported in recent kernels.

Commit d6cc1d64 (inetpeer: various changes) added a race in
unlink_from_unused().

One way to avoid taking unused_peers.lock before doing the list_empty()
test is to catch 0->1 refcnt transitions, using full barrier atomic
operations variants (atomic_cmpxchg() and atomic_inc_return()) instead
of previous atomic_inc() and atomic_add_unless() variants.

We then call unlink_from_unused() only for the owner of the 0->1
transition.

Add a new atomic_add_unless_return() static helper

With help from Arun Sharma.

Refs: https://bugzilla.kernel.org/show_bug.cgi?id=32772Reported-by: Arun Sharma <asharma@fb.com>
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reported-by: Yann Dupont <Yann.Dupont@univ-nantes.fr>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's currently exposed only through /proc which, besides requiring
screen-scraping, doesn't allow userspace to distinguish between two
identical ATM adapters with different ATM indexes.  The ATM device index
is required when using PPPoATM on a system with multiple ATM adapters.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: David Woodhouse <dwmw2@infradead.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

The AR9287 calibration code was not being called because of an
incorrect MAC revision check.
This forced the AR9287 to use the AR9285 initial calibration code and
bypass the AR9287 code entirely.
Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 79f460ca add a duplicate
linux/slab.h include to net/mac80211/scan.c - remove it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

local->ps_data wasn't cleared on disassociation, which
(in some corner cases) caused reconnections to enter
psm before association completed.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.

Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rx_status.band is used uninitialized, what disallow to work on 5GHz .

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When ip_vs was adapted to netns the ftp application was not adapted
in a correct way.
However this is a fix to avoid kernel errors. In the long term another solution
might be chosen.  I.e the ports that the ftp appl, uses should be per netns.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Stop tx queues before updating rate control to ensure
proper rate selection. Otherwise packets can be transmitted
in 40 Mhz whereas hw is configured in HT20.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Whenever there is a channel width change from 40 Mhz to 20 Mhz,
the hardware is reconfigured to ht20. Meantime before doing
the rate control updation, the packets are being transmitted are
selected rate with IEEE80211_TX_RC_40_MHZ_WIDTH.

While transmitting ht40 rate packets in ht20 mode is causing
baseband panic with AR9003 based chips.

==== BB update: BB status=0x02001109 ====
ath: ** BB state: wd=1 det=1 rdar=0 rOFDM=1 rCCK=1 tOFDM=0 tCCK=0 agc=2
src=0 **
ath: ** BB WD cntl: cntl1=0xffff0085 cntl2=0x00000004 **
ath: ** BB mode: BB_gen_controls=0x000033c0 **
ath: ** BB busy times: rx_clear=99%, rx_frame=0%, tx_frame=0% **
ath: ==== BB update: done ====

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Resetting hardware helps to recover from baseband
hang/panic for AR9003 based chips.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Although a previous fix handles the kernel panics that result from
failure to allocate a new RX buffer, memory fragmentation can be
reduced if the amsdu_8k capability is disabled as new buffers need only
be of O(0), not O(2).
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To handle amsdu_8k capability, the PCI routine of this driver must
allocate receive buffers of order 2. Under heavy load, this causes
fragmentation of memory. The present code releases the current buffer
before checking to see if a new one is availble. Recovery from
allocation failures is not possible, which results in kernel panics.

The fix is to reorder the code to check that a new buffer can be
allocated before the old one is released. If not possible, the
received frame is dropped and the old one is reused. Without this
change, it is impossible to transfer a 2 GB file without a kernel panic.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>              [2.6.{37,38,39}]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In both trigger_scan and sched_scan operations, we were checking for
the SSID length before assigning the value correctly.  Since the
memory was just kzalloc'ed, the check was always failing and SSID with
over 32 characters were allowed to go through.

This was causing a buffer overflow when copying the actual SSID to the
proper place.

This bug has been there since 2.6.29-rc4.

Cc: stable@kernel.org
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While decoding received event packet from firmware, 4 bytes
of interface header are already removed unconditionally.
So for handling event only 4 more bytes needs to be pulled.
This is achieved by changing event header length to 4.

Almost all the events, except BA stream related and AMSDU
aggregation control events, do not have the payload in their
event skb. Such events handling depends only on the event ID.
This event ID is the first four bytes of the event skb, which
is copied to a separate variable before pulling the skb header.
Hence event handling worked only for those events that didn't
have payload in event skb.

This patch fixes the broken event path of the events with
payload in their event skb without harming existing working
event path for the events without payload.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As reported by Ingo Molnar, we still have configuration combinations
where use of the WARN_RATELIMIT interfaces break the build because
dependencies don't get met.

Instead of going down the long road of trying to make it so that
ratelimit.h can get included by kernel.h or asm-generic/bug.h,
just move the interface into ratelimit.h and make users have
to include that.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>

Weiping Pan noticed that the module option description for
xmit_hash_policy was incorrect and was nice enough to post a patch to
fix it.  The text was correct, but created a line over 80 characters and
I would rather not add those.  I realized I could take a few minutes and
clean up all the descriptions and things would look much better.  This
is the result.

Based on patch from Weiping Pan <panweiping3@gmail.com>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The below patch removes vlan_buggyright and vlan_copyright from vlan_proto_init,
so that it prints out just the fullname of vlan and the version number.

before:

[   30.438203] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[   30.441542] All bugs added by David S. Miller <davem@redhat.com>

after:

[   31.513910] 802.1Q VLAN Support v1.8
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: Joe Perches <joe@perches.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use platform device rather than net device in dev_err calls before net
device has been registered to avoid messages such as

	(null): DaVinci EMAC: Failed to get EMAC clock

Also replace remaining printks in probe with dev_{err,warn}.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As these pointers have been printed without using %p they were missed in the
big network kptr_restrict conversion patch %p -> %pK from Dan Rosenberg.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current code squashes flags to bool - this makes set_flags fail whenever
some ETH_FLAG_* equivalent features are set. Fix this.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kill set but not used 'entry_offset'.

Add a default case to the switch statement so the compiler
can see that we always initialize off and size_kern before
using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>