There's a bug in today's driver where VF requests to add/remove MAC filters
always reach the Hypervisor as add requests.
This prevents the VF from changing its MAC address, as it cannot remove the
previously configured MAC and runs out of MAC credits.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.

Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.

This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each time a flow finishes reads from the classification shadow
configuration in the driver, that flow would check for pending commands
and pass them to FW if possible.
In case there's already a completion pending command, I.e., a ramrod
that has been sent to the FW and is yet to be completed while said flow
tries to configure the pending command we would get a false error message
in logs [and panic if SOE was used for driver compilation] since the
command could not have been completed.

This prevents said print [and panic]; The pending command will be sent by
the time the completion of the current sent command would arrive.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes several issues relating to asymmetric configuration:
 1. When user requests to disable TX, the local-device needs to
    advertise both PAUSE and ASM_DIR, but to avoid transmitting pause
    frames. In the 578xx, it would ignore the TX disable.

 2. When user advertises RX-only, ASM_DIR was advertised instead of
    PAUSE/ASM_DIR.

 3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared
    before setting new one, so disabling RX or TX had no impact on the
    'advertised' as appeared in the 'ethtool -a' output.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix typo in the validation rules for flower's attributes
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).

In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vitesse VSC8641 is compatible with Vitesse 82xx
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CONFIG_GIANFAR is not depended on FSL_SOC, it
can be built on non-PPC platforms.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was a missing assignment so the "if (ret)" on the next line is
never true.

Fixes: f21fb3ed ('Add support of Cavium Liquidio ethernet adapters')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to unlock before returning here.

Fixes: a0d2f206 ('Renesas Ethernet AVB PTP clock driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver fixes, June 24, 2015

Some fixes that we made recently, all need to go into stable.

patch #1 "net/mlx4_en: Release TX QP when destroying TX ring" and patch #3
"Fix wrong csum complete report when rxvlan offload is disabled" to >= 3.19

patch #2 "Wake TX queues only when there's enough room" addressing a bug
which is there from day one... should go to whatever kernels it's still applicable

patch #4 "mlx4: Disable HA for SRIOV PF RoCE devices" to >= 4.0

The patches are marked with net but are made against net-next,
as the net tree still doesn't contain all the net-next bits.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When in HA mode, the driver exposes an IB (RoCE) device instance with only
one port. Under SRIOV, the existing implementation doesn't go well with
the PF RoCE driver's role of Special QPs Para-Virtualization, etc.

As such, disable HA for the mlx4 PF RoCE device in SRIOV mode.

Fixes: a5750090 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check_csum() function relied on hwtstamp_rx_filter to know if rxvlan
offload is disabled. This is wrong since rxvlan offload can be switched
on/off regardless of hwtstamp_rx_filter.

Also moved check_csum to query CQE information to identify VLAN packets
and removed the check of IP packets, since it has been validated before.

Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Indication of a single completed packet, marked by txbbs_skipped
being bigger then zero, in not enough in order to wake up a
stopped TX queue. The completed packet may contain a single TXBB,
while next packet to be sent (after the wake up) may have multiple
TXBBs (LSO/TSO packets for example), causing overflow in queue followed
by WQE corruption and TX queue timeout.
Instead, wake the stopped queue only when there's enough room for the
worst case (maximum sized WQE) packet that we should need to handle after
the queue is opened again.

Also created an helper routine - mlx4_en_is_tx_ring_full, which checks
if the current TX ring is full or not. It provides better code readability
and removes code duplication.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX ring QP wasn't released at mlx4_en_destroy_tx_ring. Instead, the code
used the deprecated base_tx_qpn field. Move TX QP release to
mlx4_en_destroy_tx_ring and remove the base_tx_qpn field.

Fixes: ddae0349 ('net/mlx4: Change QP allocation scheme')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge first patchbomb from Andrew Morton:

 - a few misc things

 - ocfs2 udpates

 - kernel/watchdog.c feature work (took ages to get right)

 - most of MM.  A few tricky bits are held up and probably won't make 4.2.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (91 commits)
  mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc()
  mm, thp: respect MPOL_PREFERRED policy with non-local node
  tmpfs: truncate prealloc blocks past i_size
  mm/memory hotplug: print the last vmemmap region at the end of hot add memory
  mm/mmap.c: optimization of do_mmap_pgoff function
  mm: kmemleak: optimise kmemleak_lock acquiring during kmemleak_scan
  mm: kmemleak: avoid deadlock on the kmemleak object insertion error path
  mm: kmemleak: do not acquire scan_mutex in kmemleak_do_cleanup()
  mm: kmemleak: fix delete_object_*() race when called on the same memory block
  mm: kmemleak: allow safe memory scanning during kmemleak disabling
  memcg: convert mem_cgroup->under_oom from atomic_t to int
  memcg: remove unused mem_cgroup->oom_wakeups
  frontswap: allow multiple backends
  x86, mirror: x86 enabling - find mirrored memory ranges
  mm/memblock: allocate boot time data structures from mirrored memory
  mm/memblock: add extra "flags" to memblock to allow selection of memory based on attribute
  mm: do not ignore mapping_gfp_mask in page cache allocation paths
  mm/cma.c: fix typos in comments
  mm/oom_kill.c: print points as unsigned int
  mm/hugetlb: handle races in alloc_huge_page and hugetlb_reserve_pages
  ...

Pull pstore updates from Tony Luck:
 "Miscellaneous pstore improvements"

* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  ramoops: make it possible to change mem_type param.
  pstore/ram: verify ramoops header before saving record
  fs/pstore: Optimization function ramoops_init_przs
  fs/pstore: update the backend parameter in pstore module
  pstore: do not use message compression without lock

Pull f2fs updates from Jaegeuk Kim:
 "New features:
   - per-file encryption (e.g., ext4)
   - FALLOC_FL_ZERO_RANGE
   - FALLOC_FL_COLLAPSE_RANGE
   - RENAME_WHITEOUT

  Major enhancement/fixes:
   - recovery broken superblocks
   - enhance f2fs_trim_fs with a discard_map
   - fix a race condition on dentry block allocation
   - fix a deadlock during summary operation
   - fix a missing fiemap result

  .. and many minor bug fixes and clean-ups were done"

* tag 'for-f2fs-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (83 commits)
  f2fs: do not trim preallocated blocks when truncating after i_size
  f2fs crypto: add alloc_bounce_page
  f2fs crypto: fix to handle errors likewise ext4
  f2fs: drop the volatile_write flag only
  f2fs: skip committing valid superblock
  f2fs: setting discard option in parse_options()
  f2fs: fix to return exact trimmed size
  f2fs: support FALLOC_FL_INSERT_RANGE
  f2fs: hide common code in f2fs_replace_block
  f2fs: disable the discard option when device doesn't support
  f2fs crypto: remove alloc_page for bounce_page
  f2fs: fix a deadlock for summary page lock vs. sentry_lock
  f2fs crypto: clean up error handling in f2fs_fname_setup_filename
  f2fs crypto: avoid f2fs_inherit_context for symlink
  f2fs crypto: do not set encryption policy for non-directory by ioctl
  f2fs crypto: allow setting encryption policy once
  f2fs crypto: check context consistent for rename2
  f2fs: avoid duplicated code by reusing f2fs_read_end_io
  f2fs crypto: use per-inode tfm structure
  f2fs: recovering broken superblock during mount
  ...

Pull UDF fixes and cleanups from Jan Kara:
 "The contains some small fixes and improvements in error handling for
  UDF.

  Bundled is also one ext3 coding style fix and a fix in quota
  documentation"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: fix udf_load_pvoldesc()
  udf: remove double err declaration in udf_file_write_iter()
  UDF: support NFSv2 export
  fs: ext3: super: fixed a space coding style issue
  quota: Update documentation
  udf: Return error from udf_find_entry()
  udf: Make udf_get_filename() return error instead of 0 length file name
  udf: bug on exotic flag in udf_get_filename()
  udf: improve error management in udf_CS0toNLS()
  udf: improve error management in udf_CS0toUTF8()
  udf: unicode: update function name in comments
  udf: remove unnecessary test in udf_build_ustr_exact()
  udf: Return -ENOMEM when allocation fails in udf_get_filename()

Pull documentation updates from Jonathan Corbet:
 "The main thing here is Ingo's big subdirectory documenting feature
  support for each architecture.  Beyond that, it's the usual pile of
  fixes, tweaks, and small additions"

* tag 'docs-for-linus' of git://git.lwn.net/linux-2.6: (79 commits)
  doc:md: fix typo in md.txt.
  Documentation/mic/mpssd: don't build x86 userspace when cross compiling
  Documentation/prctl: don't build tsc tests when cross compiling
  Documentation/vDSO: don't build tests when cross compiling
  Doc:ABI/testing: Fix typo in sysfs-bus-fcoe
  Doc: Docbook: Change wikipedia's URL from http to https in scsi.tmpl
  Doc: Change wikipedia's URL from http to https
  Documentation/kernel-parameters: add missing pciserial to the earlyprintk
  Doc:pps: Fix typo in pps.txt
  kbuild : Fix documentation of INSTALL_HDR_PATH
  Documentation: filesystems: updated struct file_operations documentation in vfs.txt
  kbuild: edit explanation of clean-files variable
  Doc: ja_JP: Fix typo in HOWTO
  Move freefall program from Documentation/ to tools/
  Documentation: ARM: EXYNOS: Describe boot loaders interface
  Doc:nfc: Fix typo in nfc-hci.txt
  vfs: Minor documentation fix
  Doc: networking: txtimestamp: fix printf format warning
  Documentation, intel_pstate: Improve legacy mode internal governors description
  Documentation: extend use case for EXPORT_SYMBOL_GPL()
  ...

Pull input subsystem updates from Dmitry Torokhov:
 "Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
  hardwired within the input core but use LED subsystem and so allow use
  of different triggers; Hans de Goede did a large update for the ALPS
  touchpad driver; we have new TI drv2665 haptics driver and DA9063
  OnKey driver, and host of other drivers got various fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
  Input: pixcir_i2c_ts - fix receive error
  MAINTAINERS: remove non existent input mt git tree
  Input: improve usage of gpiod API
  tty/vt/keyboard: define LED triggers for VT keyboard lock states
  tty/vt/keyboard: define LED triggers for VT LED states
  Input: export LEDs as class devices in sysfs
  Input: cyttsp4 - use swap() in cyttsp4_get_touch()
  Input: goodix - do not explicitly set evbits in input device
  Input: goodix - export id and version read from device
  Input: goodix - fix variable length array warning
  Input: goodix - fix alignment issues
  Input: add OnKey driver for DA9063 MFD part
  Input: elan_i2c - add product IDs FW names
  Input: elan_i2c - add support for multi IC type and iap format
  Input: focaltech - report finger width to userspace
  tty: remove platform_sysrq_reset_seq
  Input: synaptics_i2c - use proper boolean values
  Input: psmouse - use true instead of 1 for boolean values
  Input: cyapa - fix a few typos in comments
  Input: stmpe-ts - enforce device tree only mode
  ...

Pull EDAC updates from Borislav Petkov:

 - New APM X-Gene SoC EDAC driver (Loc Ho)

 - AMD error injection module improvements (Aravind Gopalakrishnan)

 - Altera Arria 10 support (Thor Thayer)

 - misc fixes and cleanups all over the place

* tag 'edac_for_4.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (28 commits)
  EDAC: Update Documentation/edac.txt
  EDAC: Fix typos in Documentation/edac.txt
  EDAC, mce_amd_inj: Set MISCV on injection
  EDAC, mce_amd_inj: Move bit preparations before the injection
  EDAC, mce_amd_inj: Cleanup and simplify README
  EDAC, altera: Do not allow suspend when EDAC is enabled
  EDAC, mce_amd_inj: Make inj_type static
  arm: socfpga: dts: Add Arria10 SDRAM EDAC DTS support
  EDAC, altera: Add Arria10 EDAC support
  EDAC, altera: Refactor for Altera CycloneV SoC
  EDAC, altera: Generalize driver to use DT Memory size
  EDAC, mce_amd_inj: Add README file
  EDAC, mce_amd_inj: Add individual permissions field to dfs_node
  EDAC, mce_amd_inj: Modify flags attribute to use string arguments
  EDAC, mce_amd_inj: Read out number of MCE banks from the hardware
  EDAC, mce_amd_inj: Use MCE_INJECT_GET macro for bank node too
  EDAC, xgene: Fix cpuid abuse
  EDAC, mpc85xx: Extend error address to 64 bit
  EDAC, mpc8xxx: Adapt for FSL SoC
  EDAC, edac_stub: Drop arch-specific include
  ...

Pull pin control updates from Linus Walleij:
 "Here is the bulk of pin control changes for the v4.2 series: Quite a
  lot of new SoC subdrivers and two new main drivers this time, apart
  from that business as usual.

  Details:

  Core functionality:
   - Enable exclusive pin ownership: it is possible to flag a pin
     controller so that GPIO and other functions cannot use a single pin
     simultaneously.

  New drivers:
   - NXP LPC18xx System Control Unit pin controller
   - Imagination Pistachio SoC pin controller

  New subdrivers:
   - Freescale i.MX7d SoC
   - Intel Sunrisepoint-H PCH
   - Renesas PFC R8A7793
   - Renesas PFC R8A7794
   - Mediatek MT6397, MT8127
   - SiRF Atlas 7
   - Allwinner A33
   - Qualcomm MSM8660
   - Marvell Armada 395
   - Rockchip RK3368

  Cleanups:
   - A big cleanup of the Marvell MVEBU driver rectifying it to
     correspond to reality
   - Drop platform device probing from the SH PFC driver, we are now a
     DT only shop for SuperH
   - Drop obsolte multi-platform check for SH PFC
   - Various janitorial: constification, grammar etc

  Improvements:
   - The AT91 GPIO portions now supports the set_multiple() feature
   - Split out SPI pins on the Xilinx Zynq
   - Support DTs without specific function nodes in the i.MX driver"

* tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
  pinctrl: rockchip: add support for the rk3368
  pinctrl: rockchip: generalize perpin driver-strength setting
  pinctrl: sh-pfc: r8a7794: add SDHI pin groups
  pinctrl: sh-pfc: r8a7794: add MMCIF pin groups
  pinctrl: sh-pfc: add R8A7794 PFC support
  pinctrl: make pinctrl_register() return proper error code
  pinctrl: mvebu: armada-39x: add support for Armada 395 variant
  pinctrl: mvebu: armada-39x: add missing SATA functions
  pinctrl: mvebu: armada-39x: add missing PCIe functions
  pinctrl: mvebu: armada-38x: add ptp functions
  pinctrl: mvebu: armada-38x: add ua1 functions
  pinctrl: mvebu: armada-38x: add nand functions
  pinctrl: mvebu: armada-38x: add sata functions
  pinctrl: mvebu: armada-xp: add dram functions
  pinctrl: mvebu: armada-xp: add nand rb function
  pinctrl: mvebu: armada-xp: add spi1 function
  pinctrl: mvebu: armada-39x: normalize ref clock naming
  pinctrl: mvebu: armada-xp: rename spi to spi0
  pinctrl: mvebu: armada-370: align spi1 clock pin naming
  pinctrl: mvebu: armada-370: align VDD cpu-pd pin naming with datasheet
  ...

Pull backlight updates from Lee Jones:
 "Changes to existing drivers:

   - supply MODULE_DEVICE_TABLE() to ensure probing
   - constify struct; da9052_bl
   - enable compile test; lcd_l4f00242t03, lcd_lms283fg05, backlight_gpio
   - suspend/resume bugfix; lp855x_bl
   - devm_gpiod_get_optional() API fixup; pwm_bl
   - error handling fixup; backlight"

* tag 'backlight-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: Change the return type of backlight_update_status() to int
  backlight: pwm_bl: Simplify usage of devm_gpiod_get_optional
  backlight: lp855x: Don't clear level on suspend/blank
  backlight: Allow compile test of GPIO consumers if !GPIOLIB
  video: backlight: da9052: Constify platform_device_id
  gpio-backlight: Discover driver during boot time

Beginning at commit d52d3997 ("ipv6: Create percpu rt6_info"), the
following INFO splat is logged:

  ===============================
  [ INFO: suspicious RCU usage. ]
  4.1.0-rc7-next-20150612 #1 Not tainted
  -------------------------------
  kernel/sched/core.c:7318 Illegal context switch in RCU-bh read-side critical section!
  other info that might help us debug this:
  rcu_scheduler_active = 1, debug_locks = 0
   3 locks held by systemd/1:
   #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff815f0c8f>] rtnetlink_rcv+0x1f/0x40
   #1:  (rcu_read_lock_bh){......}, at: [<ffffffff816a34e2>] ipv6_add_addr+0x62/0x540
   #2:  (addrconf_hash_lock){+...+.}, at: [<ffffffff816a3604>] ipv6_add_addr+0x184/0x540
  stack backtrace:
  CPU: 0 PID: 1 Comm: systemd Not tainted 4.1.0-rc7-next-20150612 #1
  Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20   04/17/2014
  Call Trace:
    dump_stack+0x4c/0x6e
    lockdep_rcu_suspicious+0xe7/0x120
    ___might_sleep+0x1d5/0x1f0
    __might_sleep+0x4d/0x90
    kmem_cache_alloc+0x47/0x250
    create_object+0x39/0x2e0
    kmemleak_alloc_percpu+0x61/0xe0
    pcpu_alloc+0x370/0x630

Additional backtrace lines are truncated.  In addition, the above splat
is followed by several "BUG: sleeping function called from invalid
context at mm/slub.c:1268" outputs.  As suggested by Martin KaFai Lau,
these are the clue to the fix.  Routine kmemleak_alloc_percpu() always
uses GFP_KERNEL for its allocations, whereas it should follow the gfp
from its callers.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@vger.kernel.org>	[3.18+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit 077fcf11 ("mm/thp: allocate transparent hugepages on
local node"), we handle THP allocations on page fault in a special way -
for non-interleave memory policies, the allocation is only attempted on
the node local to the current CPU, if the policy's nodemask allows the
node.

This is motivated by the assumption that THP benefits cannot offset the
cost of remote accesses, so it's better to fallback to base pages on the
local node (which might still be available, while huge pages are not due
to fragmentation) than to allocate huge pages on a remote node.

The nodemask check prevents us from violating e.g.  MPOL_BIND policies
where the local node is not among the allowed nodes.  However, the
current implementation can still give surprising results for the
MPOL_PREFERRED policy when the preferred node is different than the
current CPU's local node.

In such case we should honor the preferred node and not use the local
node, which is what this patch does.  If hugepage allocation on the
preferred node fails, we fall back to base pages and don't try other
nodes, with the same motivation as is done for the local node hugepage
allocations.  The patch also moves the MPOL_INTERLEAVE check around to
simplify the hugepage specific test.

The difference can be demonstrated using in-tree transhuge-stress test
on the following 2-node machine where half memory on one node was
occupied to show the difference.

> numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 24 25 26 27 28 29 30 31 32 33 34 35
node 0 size: 7878 MB
node 0 free: 3623 MB
node 1 cpus: 12 13 14 15 16 17 18 19 20 21 22 23 36 37 38 39 40 41 42 43 44 45 46 47
node 1 size: 8045 MB
node 1 free: 7818 MB
node distances:
node   0   1
  0:  10  21
  1:  21  10

Before the patch:
> numactl -p0 -C0 ./transhuge-stress
transhuge-stress: 2.197 s/loop, 0.276 ms/page,   7249.168 MiB/s 7962 succeed,    0 failed, 1786 different pages

> numactl -p0 -C12 ./transhuge-stress
transhuge-stress: 2.962 s/loop, 0.372 ms/page,   5376.172 MiB/s 7962 succeed,    0 failed, 3873 different pages

Number of successful THP allocations corresponds to free memory on node 0 in
the first case and node 1 in the second case, i.e. -p parameter is ignored and
cpu binding "wins".

After the patch:
> numactl -p0 -C0 ./transhuge-stress
transhuge-stress: 2.183 s/loop, 0.274 ms/page,   7295.516 MiB/s 7962 succeed,    0 failed, 1760 different pages

> numactl -p0 -C12 ./transhuge-stress
transhuge-stress: 2.878 s/loop, 0.361 ms/page,   5533.638 MiB/s 7962 succeed,    0 failed, 1750 different pages

> numactl -p1 -C0 ./transhuge-stress
transhuge-stress: 4.628 s/loop, 0.581 ms/page,   3440.893 MiB/s 7962 succeed,    0 failed, 3918 different pages

The -p parameter is respected regardless of cpu binding.

> numactl -C0 ./transhuge-stress
transhuge-stress: 2.202 s/loop, 0.277 ms/page,   7230.003 MiB/s 7962 succeed,    0 failed, 1750 different pages

> numactl -C12 ./transhuge-stress
transhuge-stress: 3.020 s/loop, 0.379 ms/page,   5273.324 MiB/s 7962 succeed,    0 failed, 3916 different pages

Without -p parameter, hugepage restriction to CPU-local node works as before.

Fixes: 077fcf11 ("mm/thp: allocate transparent hugepages on local node")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org>	[4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

One of the rocksdb people noticed that when you do something like this

    fallocate(fd, FALLOC_FL_KEEP_SIZE, 0, 10M)
    pwrite(fd, buf, 5M, 0)
    ftruncate(5M)

on tmpfs, the file would still take up 10M: which led to super fun
issues because we were getting ENOSPC before we thought we should be
getting ENOSPC.  This patch fixes the problem, and mirrors what all the
other fs'es do (and was agreed to be the correct behaviour at LSF).

I tested it locally to make sure it worked properly with the following

    xfs_io -f -c "falloc -k 0 10M" -c "pwrite 0 5M" -c "truncate 5M" file

Without the patch we have "Blocks: 20480", with the patch we have the
correct value of "Blocks: 10240".
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When hot add two nodes continuously, we found the vmemmap region info is
a bit messed.  The last region of node 2 is printed when node 3 hot
added, like the following:

  Initmem setup node 2 [mem 0x0000000000000000-0xffffffffffffffff]
   On node 2 totalpages: 0
   Built 2 zonelists in Node order, mobility grouping on.  Total pages: 16090539
   Policy zone: Normal
   init_memory_mapping: [mem 0x40000000000-0x407ffffffff]
    [mem 0x40000000000-0x407ffffffff] page 1G
    [ffffea1000000000-ffffea10001fffff] PMD -> [ffff8a077d800000-ffff8a077d9fffff] on node 2
    [ffffea1000200000-ffffea10003fffff] PMD -> [ffff8a077de00000-ffff8a077dffffff] on node 2
  ...
    [ffffea101f600000-ffffea101f9fffff] PMD -> [ffff8a074ac00000-ffff8a074affffff] on node 2
    [ffffea101fa00000-ffffea101fdfffff] PMD -> [ffff8a074a800000-ffff8a074abfffff] on node 2
  Initmem setup node 3 [mem 0x0000000000000000-0xffffffffffffffff]
   On node 3 totalpages: 0
   Built 3 zonelists in Node order, mobility grouping on.  Total pages: 16090539
   Policy zone: Normal
   init_memory_mapping: [mem 0x60000000000-0x607ffffffff]
    [mem 0x60000000000-0x607ffffffff] page 1G
    [ffffea101fe00000-ffffea101fffffff] PMD -> [ffff8a074a400000-ffff8a074a5fffff] on node 2 <=== node 2 ???
    [ffffea1800000000-ffffea18001fffff] PMD -> [ffff8a074a600000-ffff8a074a7fffff] on node 3
    [ffffea1800200000-ffffea18005fffff] PMD -> [ffff8a074a000000-ffff8a074a3fffff] on node 3
    [ffffea1800600000-ffffea18009fffff] PMD -> [ffff8a0749c00000-ffff8a0749ffffff] on node 3
  ...

The cause is the last region was missed at the and of hot add memory,
and p_start, p_end, node_start were not reset, so when hot add memory to
a new node, it will consider they are not contiguous blocks and print
the previous one.  So we print the last vmemmap region at the end of hot
add memory to avoid the confusion.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The simple check for zero length memory mapping may be performed
earlier.  So that in case of zero length memory mapping some unnecessary
code is not executed at all.  It does not make the code less readable
and saves some CPU cycles.
Signed-off-by: Piotr Kwapulinski <kwapulinski.piotr@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kmemleak memory scanning uses finer grained object->lock spinlocks
primarily to avoid races with the memory block freeing.  However, the
pointer lookup in the rb tree requires the kmemleak_lock to be held.
This is currently done in the find_and_get_object() function for each
pointer-like location read during scanning.  While this allows a low
latency on kmemleak_*() callbacks on other CPUs, the memory scanning is
slower.

This patch moves the kmemleak_lock outside the scan_block() loop,
acquiring/releasing it only once per scanned memory block.  The
allow_resched logic is moved outside scan_block() and a new
scan_large_block() function is implemented which splits large blocks in
MAX_SCAN_SIZE chunks with cond_resched() calls in-between.  A redundant
(object->flags & OBJECT_NO_SCAN) check is also removed from
scan_object().

With this patch, the kmemleak scanning performance is significantly
improved: at least 50% with lock debugging disabled and over an order of
magnitude with lock proving enabled (on an arm64 system).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

While very unlikely (usually kmemleak or sl*b bug), the create_object()
function in mm/kmemleak.c may fail to insert a newly allocated object into
the rb tree.  When this happens, kmemleak disables itself and prints
additional information about the object already found in the rb tree.
Such printing is done with the parent->lock acquired, however the
kmemleak_lock is already held.  This is a potential race with the scanning
thread which acquires object->lock and kmemleak_lock in a

This patch removes the locking around the 'parent' object information
printing.  Such object cannot be freed or removed from object_tree_root
and object_list since kmemleak_lock is already held.  There is a very
small risk that some of the object data is being modified on another CPU
but the only downside is inconsistent information printing.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kmemleak_do_cleanup() work thread already waits for the kmemleak_scan
thread to finish via kthread_stop().  Waiting in kthread_stop() while
scan_mutex is held may lead to deadlock if kmemleak_scan_thread() also
waits to acquire for scan_mutex.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Calling delete_object_*() on the same pointer is not a standard use case
(unless there is a bug in the code calling kmemleak_free()).  However,
during kmemleak disabling (error or user triggered via /sys), there is a
potential race between kmemleak_free() calls on a CPU and
__kmemleak_do_cleanup() on a different CPU.

The current delete_object_*() implementation first performs a look-up
holding kmemleak_lock, increments the object->use_count and then
re-acquires kmemleak_lock to remove the object from object_tree_root and
object_list.

This patch simplifies the delete_object_*() mechanism to both look up
and remove an object from the object_tree_root and object_list
atomically (guarded by kmemleak_lock).  This allows safe concurrent
calls to delete_object_*() on the same pointer without additional
locking for synchronising the kmemleak_free_enabled flag.

A side effect is a slight improvement in the delete_object_*() performance
by avoiding acquiring kmemleak_lock twice and incrementing/decrementing
object->use_count.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kmemleak scanning thread can run for minutes.  Callbacks like
kmemleak_free() are allowed during this time, the race being taken care
of by the object->lock spinlock.  Such lock also prevents a memory block
from being freed or unmapped while it is being scanned by blocking the
kmemleak_free() -> ...  -> __delete_object() function until the lock is
released in scan_object().

When a kmemleak error occurs (e.g.  it fails to allocate its metadata),
kmemleak_enabled is set and __delete_object() is no longer called on
freed objects.  If kmemleak_scan is running at the same time,
kmemleak_free() no longer waits for the object scanning to complete,
allowing the corresponding memory block to be freed or unmapped (in the
case of vfree()).  This leads to kmemleak_scan potentially triggering a
page fault.

This patch separates the kmemleak_free() enabling/disabling from the
overall kmemleak_enabled nob so that we can defer the disabling of the
object freeing tracking until the scanning thread completed.  The
kmemleak_free_part() is deliberately ignored by this patch since this is
only called during boot before the scanning thread started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Tested-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg->under_oom tracks whether the memcg is under OOM conditions and is
an atomic_t counter managed with mem_cgroup_[un]mark_under_oom().  While
atomic_t appears to be simple synchronization-wise, when used as a
synchronization construct like here, it's trickier and more error-prone
due to weak memory ordering rules, especially around atomic_read(), and
false sense of security.

For example, both non-trivial read sites of memcg->under_oom are a bit
problematic although not being actually broken.

* mem_cgroup_oom_register_event()

  It isn't explicit what guarantees the memory ordering between event
  addition and memcg->under_oom check.  This isn't broken only because
  memcg_oom_lock is used for both event list and memcg->oom_lock.

* memcg_oom_recover()

  The lockless test doesn't have any explanation why this would be
  safe.

mem_cgroup_[un]mark_under_oom() are very cold paths and there's no point
in avoiding locking memcg_oom_lock there.  This patch converts
memcg->under_oom from atomic_t to int, puts their modifications under
memcg_oom_lock and documents why the lockless test in
memcg_oom_recover() is safe.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit 49426420 ("mm: memcg: handle non-error OOM situations
more gracefully"), nobody uses mem_cgroup->oom_wakeups.  Remove it.

While at it, also fold memcg_wakeup_oom() into memcg_oom_recover() which
is its only user.  This cleanup was suggested by Michal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Change frontswap single pointer to a singly linked list of frontswap
implementations.  Update Xen tmem implementation as register no longer
returns anything.

Frontswap only keeps track of a single implementation; any
implementation that registers second (or later) will replace the
previously registered implementation, and gets a pointer to the previous
implementation that the new implementation is expected to pass all
frontswap functions to if it can't handle the function itself.  However
that method doesn't really make much sense, as passing that work on to
every implementation adds unnecessary work to implementations; instead,
frontswap should simply keep a list of all registered implementations
and try each implementation for any function.  Most importantly, neither
of the two currently existing frontswap implementations in the kernel
actually do anything with any previous frontswap implementation that
they replace when registering.

This allows frontswap to successfully manage multiple implementations by
keeping a list of them all.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

UEFI GetMemoryMap() uses a new attribute bit to mark mirrored memory
address ranges.  See UEFI 2.5 spec pages 157-158:

  http://www.uefi.org/sites/default/files/resources/UEFI%202_5.pdf

On EFI enabled systems scan the memory map and tell memblock about any
mirrored ranges.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Xiexiuqi <xiexiuqi@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Try to allocate all boot time kernel data structures from mirrored
memory.

If we run out of mirrored memory print warnings, but fall back to using
non-mirrored memory to make sure that we still boot.

By number of bytes, most of what we allocate at boot time is the page
structures.  64 bytes per 4K page on x86_64 ...  or about 1.5% of total
system memory.  For workloads where the bulk of memory is allocated to
applications this may represent a useful improvement to system
availability since 1.5% of total memory might be a third of the memory
allocated to the kernel.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Xiexiuqi <xiexiuqi@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>