Commits · bea69c47f5b93b3142f8833f8a34b666d5d7d6a7 · nexedi / linux

21 Dec, 2013 6 commits

b44: activate PHY when MAC is off · bea69c47

Hauke Mehrtens authored Dec 20, 2013

Without this patch we can not access the PHY when the MAC is switched
off. This PHY access is needed to configure the switch, which is done
through PHY registers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

bea69c47

b44: add phylib support · 86f4ea63

Hauke Mehrtens authored Dec 20, 2013

Most of the older home routers based on the Broadcom BCM47XX SoC series
are using a MAC that is supported by b44. On most of these routers not
the internal PHY of this MAC core is used, but a switch sometimes on an
external chip or integrated into the same SoC as the Ethernet core.
For this switch a special PHY driver is needed which should not be
integrated into b44 as the same switches are also used by other
Broadcom home networking SoCs which are using different Ethernet MAC
drivers. This was tested with the b53 switch driver which is currently
on its way to mainline.

If the internal PHY is not used, b44 will now search on the MDIO bus
for a phy and use the Linux phylib subsystem to register a driver.
Support for the internal PHY must stay here, because there are some
device which are suing the internal phy.

With this patch we scan the mdio bus when the sprom or nvram says that
the PHY address is 30, if a PHY was found at this address b44 uses it.

This was tested with a BCM4704, BCM4712 and BCM5354.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

86f4ea63

b44: rename b44_mii_{read, write} to b44_mdio_{read, write}_mii · 348baa6c

Hauke Mehrtens authored Dec 20, 2013

The next patch will add these functions for phylib, and we should
rename the old ones before. This now indicates that these functions are
used for the mdio registers and on the mii interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

348baa6c

b44: abort when no PHY is available at all · 7befa6ab

Hauke Mehrtens authored Dec 20, 2013

When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

7befa6ab

b44: rename B44_PHY_ADDR_NO_PHY to B44_PHY_ADDR_NO_LOCAL_PHY · 5ab6329c

Hauke Mehrtens authored Dec 20, 2013

The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

5ab6329c

b44: check register instead of PHY address to detect external PHY · d6194195

Hauke Mehrtens authored Dec 20, 2013

The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.

This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

d6194195

20 Dec, 2013 26 commits

tcp: autocork should not hold first packet in write queue · a181ceb5

Eric Dumazet authored Dec 17, 2013

Willem noticed a TCP_RR regression caused by TCP autocorking
on a Mellanox test bed. MLX4_EN_TX_COAL_TIME is 16 us, which can be
right above RTT between hosts.

We can receive a ACK for a packet still in NIC TX ring buffer or in a
softnet completion queue.

Fix this by always pushing the skb if it is at the head of write queue.

Also, as TX completion is lockless, it's safer to perform sk_wmem_alloc
test after setting TSQ_THROTTLED.

erd:~# MIB="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
erd:~#  ./netperf -H remote -t TCP_RR -- -o $MIB | tail -n 1
(repeat 3 times)

Before patch :

18,1049.87,41004,39631,6295.47
17,239.52,40804,48,2912.79
18,348.40,40877,54,3573.39

After patch :

18,22.84,4606,38,16.39
17,21.56,2871,36,13.51
17,22.46,2705,37,11.83
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f54b3111 ("tcp: auto corking")
Signed-off-by: David S. Miller <davem@davemloft.net>

a181ceb5

net_sched: fix regression in tc_action_ops · a792866a

Eric Dumazet authored Dec 20, 2013

list_for_each_entry(a, &act_base, head) doesn't
exit with a = NULL if we reached the end of the list.

tcf_unregister_action(), tc_lookup_action_n() and tc_lookup_action()
need fixes.

Remove tc_lookup_action_id() as its unused and not worth 'fixing'
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f747c26 ("net_sched: convert tc_action_ops to use struct list_head")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

a792866a

net_sched: fix a regression in tcf_proto_lookup_ops() · dcd76081

Eric Dumazet authored Dec 20, 2013

list_for_each_entry(t, &tcf_proto_base, head) doesn't
exit with t = NULL if we reached the end of the list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 36272874 ("net_sched: convert tcf_proto_ops to use struct
list_head")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dcd76081

net_sched: fix a regression in tc actions · 568a153a

WANG Cong authored Dec 20, 2013

This patch fixes:
1) pass mask rather than size to tcf_hashinfo_init()
2) the cleanup should be in reversed order in mirred_cleanup_module()
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 369ba567 ("net_sched: init struct tcf_hashinfo at register time")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

568a153a

Merge branch 'bridge_cleanups' · 852ad5e6

David S. Miller authored Dec 19, 2013

Tan Xiaojun says:

====================
bridge: cleanup and fix checkpatch errors

Clean up and fix some checkpatch errors in bridge driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>