Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some features currently not supported by the driver (e.g. RSS) require the
use of extended descriptors, but the driver is setup to only use legacy
descriptors in all modes except for when jumbo frames are enabled on some
parts.  Convert the driver to always use extended descriptors in order to
enable the forthcoming support of these other features.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Inspect the payload of PPPOE session messages for the 4 tuples to generate
skb->rxhash.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the 802.1Q packets, if the NIC doesn't support hw-accel-vlan-rx, RPS
won't inspect the internal 4 tuples to generate skb->rxhash, so this kind
of traffic can't get any benefit from RPS.

This patch adds the support for 802.1Q to RPS.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are valid configurations where Max BW is configured to zero for
some VNs.
Print the message only if debugging is enabled and do not call the
configuration "illegal".

[v2: use DP(), not BNX2X_DBG_ERR(); recommended by Eilon Greenstein.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 9aa32835 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*

The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors).  In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.

We do not explicitly select the Kconfig dependencies, as this would force
EMAC on.  Doing it in the defconfig allows more flexibility.

Tested on a canyondlands board.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Korina.c is a MIPS-specific SOC driver and <asm/segment> is empty on
MIPS since 2.1.7 ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I will no longer maintain netxen_nic driver.
Sony Chacko and Rajesh Borundia are taking over.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the p1010 processor to select the flexcan network driver.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If our CAN device's device tree node has a clock-frequency property,
then use that value for the can devices clock frequency.  If not, fall
back to asking the platform/mach code for the clock frequency associated
with the flexcan device.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

On powerpc, the OpenFirmware devices are not matched without specifying
an of_match array.  Introduce that array as that is used for matching
on the Freescale P1010 processor.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Make flexcan driver handle register reads in the appropriate endianess.
This was a basic search and replace and then define some inlines.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

powerpc does not have a mach-####/clock.h.  When testing, I found neither
arm nor powerpc needed the mach/clock.h at all so I removed it.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove no longer used operation.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.

Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
	ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
	ndo_set_rx_mode but do not support uc filtering
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Benefit from use of ndo_change_rx_flags in handling change of promisc
and allmulti. No need to store previous state locally.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Crack open GRE packets in __skb_get_rxhash to compute 4-tuple hash on
in encapsulated packet.  Note that this is used only when the
__skb_get_rxhash is taken, in particular only when the device does
not compute provide the rxhash (ie. feature is disabled).

This was tested by creating a single GRE tunnel between two 16 core
AMD machines.  200 netperf TCP_RR streams were ran with 1 byte
request and response size.

Without patch: 157497 tps, 50/90/99% latencies 1250/1292/1364 usecs
With patch: 325896 tps, 50/90/99% latencies 603/848/1169
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Basics for looking for ports in encapsulated packets in tunnels.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The l4_rxhash flag was added to the skb structure to indicate
that the rxhash value was computed over the 4 tuple for the
packet which includes the port information in the encapsulated
transport packet.  This is used by the stack to preserve the
rxhash value in __skb_rx_tunnel.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use some variables for clarity and extensibility.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add pr_fmt(fmt) KBUILD_MODNAME ": " to prefix messages with "bnx2x: ".
Remove #define DP_LEVEL and use pr_notice.
Repeating KERN_<LEVEL> isn't necessary in multi-line printks.
printk macro neatening, use fmt and ##__VA_ARGS__.
Coalesce long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Uses of pr_cont should be avoided where reasonably possible
because they can be interleaved by other threads and processes.

Coalesce pr_cont uses.

Fix typos, duplicated words and spacing in DP uses caused
by split multi-line formats.  Coalesce some of these
split formats.  Add missing terminating newlines to DP uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use %pM and mac address directly instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many implementations ignore the value of max_frames and do not
treat usecs == 0 as special.  Document this as deprecated.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also explicitly state how to disable interrupt coalescing.

Remove the now-redundant text from field descriptions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current descriptions state that these fields specify 'How many
packets to delay ... after a packet ...' which implies that the
hardware should wait for (max_coalesced_frames + 1) completions before
generating an interrupt.  It is also stated that setting both this
field and the corresponding 'coalesce_usecs' field to 0 is invalid.
Together, this implies that the hardware must always be configured
to delay a completion IRQ for at least 1 usec or 1 more completion.

I believe that the addition of 1 is not intended, and David Miller
confirms that the original implementation (in tg3) does not do this.
Clarify the descriptions of these fields to avoid this interpretation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reorders and duplicates some wording, but should make no
substantive changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since sungem_phy is used by multiple, unrelated, drivers make it
build as a real module under drivers/net.

depmod will pick up the symbol dependency and make sure sungem_phy.ko
gets loaded any time sungem.ko or spider_net.ko is loaded.
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the following sparse warning by adding the missing
__iomem annotation.

drivers/net/can/mscan/mscan.c:73:32: warning: incorrect type in argument 1 (different address spaces)
drivers/net/can/mscan/mscan.c:73:32:    expected unsigned char volatile [noderef] [usertype] <asn:2>*addr
drivers/net/can/mscan/mscan.c:73:32:    got unsigned char *<noident>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fixes build failures of the spider_net driver because it tries
to use a convoluted path to include this header.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch extends the HiperSockets device driver to send and receive
af_iucv traffic over HiperSockets transport.
TX: Driver uses new asynchronous delivery of storage blocks to pass
    flow control/congestion information from the HiperSockets microcode
    to the af_iucv socket.
RX: Memory for incoming traffic is preallocated and passed to
    HiperSockets layer. If receiver is not capable to clean its buffers
    shared with HiperSockets and pass new memory to the HiperSockets
    layer this will cause flow control/congestion events on the
    sender.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch exploits the QDIO support for asynchronous delivery of storage
blocks for Hipersockets. The exploitation is not configured per default and
may be enabled via the function qeth_configure_cq.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch ensures that signal adapter commands are issued if they are
indicated to be required.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>