Generate log when receive tx reply with bt_kill count > 0 and
in advance bt coex mode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bt config command need to send before the init calibration command,
driver need to let uCode know that calibrations are being performed now
in order to assure antenna is not being taken to BT use during radio/dsp
reads/writes

Also, bt_coex_priorty_table command need to be send right after the
bt_config_command during init sequence. Followed by bt coex envelope
command to initialize and prepare uCode bt state machine
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adding the bluetooth full concurrency support for WiFi/BT combo devices.

Driver should configure uCode to operate in "full concurrency" mode (via
LUT) if both conditions are met:
 - Antenna Coupling is more than 35dB
 - WiFi Channel Inhibition Request is hornored by BT Core

Currently, there is no antenna coupling information provided by uCode;
use module parameter to specified the antenna coupling in dB.

When in "full concurrency" mode, driver need to download different LUT
to uCode while sending bt configuration command; also, driver need to
configure the device operate in 1x1 while in full concurrency mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When bluetooth indicated high load, we should use
only antenna A in 2.4 GHz for management frames.
Add this condition to iwl_toggle_tx_ant() to make
sure it'll always be met. Note that scanning has
a separate way of forcing the antenna, because we
should scan on antenna A only regardless of BT
traffic load.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Disable plcp error checking for 6000g2b devices, with wifi/bt coex;
this got trigger too often, disable for now until finding better
trigger point.

Also extend the firmware reload timer much longer for BT coex to make sure
there are will be no mistake to reload firmware too fast and too often.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BT SCO needs to be re-applied to the device,
while the traffic load just needs to be correct
in software.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IBSS doesn't allow for coexistence, so it
should be disabled.

Additionally, disable reacting to the BT
profile notification when in IBSS mode,
it likely won't be sent by the device to
start with though.

Also, in IBSS mode, BT coexistence isn't as fully-featured
and we must use a single antenna only. So instead of
peppering the code with new checks, simply pretend
we are in high BT traffic load, which has the needed
effect of disabling antenna B use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we turn off the device, reset BT
data so that we don't have outdated
information when we come up again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Depending on the amount of bluetooth traffic,
using the shared antenna (antenna B) will have
adverse impact on both bluetooth and wireless
traffic. Add controls to improve the situation
by making rate scaling depend on the BT load.

When there's high bluetooth traffic load, there's
little point in trying to aggregate as BT traffic
would disrupt the aggregated frames all the time,
so simply don't start sessions then.

When BT traffic returns to lower levels, the rate
scaling will come here again automatically when
wifi traffic is high enough, and then it will be
able to successfully enable aggregation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When advanced bt coex enabled, uCode will send bt status
notification to driver, here add support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BT ignore bit should be set when transmitting
auth, assoc response and eap frames.

Also, scanning should set the BT ignore bit for the
probe request transmission; Note that we only use
the non-shared antenna.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

6000g2b hardware implements advance bluetooth coexist command,
implement base on the new API command strucutre.

Also increment the API 5 to support the advance BT/WIfi coex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new 6000g2b hardware requires a different
bluetooth coexist implementation on the host,
this adds the command/notification definitions
for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No code or function changes, just some cleanup work for
out-of-date comments
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No functional changes, update comments to match current file structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Unlike most other workqueue-tasks, the restart_work is
not scheduled onto mac80211's private per-interface
workqueue, but onto one of the system-wide workqueues.

Therefore the mac80211-stack has to cancel any pending
restarts, before destroying the shared device context
and handing back the memory. Otherwise - under very
unlucky circumstances - there could be a stale work-
item left, because some other kernel component might
have delayed the execution of ieee80211_restart_work
for too long.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ISL3887 chip needs a USB reset, whenever the
usb-frontend module "p54usb" is reloaded.

This patch fixes an off-by-one bug, if the user
is running a kernel without the CONFIG_PM option
set and for some reason (e.g.: compat-wireless)
wants to switch between different p54usb modules.

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As my nokia address doesn't work anymore, it's better just to remove the
copyright contact altogether. We have MODULE_AUTHOR() scripts for these
anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Luciano should be the contact person for the include/linux/spi/wl12xx.h file.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I use now my adurom.com address.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds an Kconfig option, which allows the user
to select, whenever he/she wants to include a 4k blob for
generic calibration and interface values into the driver,
or cut the module size by about 15 to 20%.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Descriptors are currently logged with ATH5K_DEBUG_RESET,
which isn't really apt, and also means we can't see just
the descriptor setup or just the resets.  Add a new
debug level just for that.
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix some comments:
    s/transmition/transmission/
    s/puting/putting/
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix spelling and readability of a few lines of kernel doc:

    s/issueing/issuing/g
    s/approriate/appropriate/g
    s/supported by simply/supported simply by/
    s/IEEE80211_HW_BEACON_FILTERING/IEEE80211_HW_BEACON_FILTER/g
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mesh_hdr only used when CONFIG_MAC80211_MESH is defined
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix walking past the end of the bitrate_table array
in the case when the loop counter == BITRATE_TABLE_SIZE.

Reported by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Standardize logging messages from
	printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
	wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To make del_timer_sync() works we have to assure that timer function
does not rearm the timer. To achieve that we cancel timer with
STATUS_EXIT_PENDING bit set in __iwl{3945,}_down function.

Patch also fix priv->txq memory usage after free for iwl3945, because
it move timer cancellation before iwl3945_hw_txq_ctx_free(priv) is called.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-core.c
	drivers/net/wireless/iwlwifi/iwl-core.h

Add some documentation for cfg80211. I'm hoping some of
the regulatory documentation will be filled by somebody
more familiar with it, hint hint! :)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a scan is aborted because the corresponding
virtual interface is removed, we may still later
attempt to tell mac80211 that the scan completed.
This is obviously wrong, since we already told it
that it was aborted, so don't do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Even when we configure WEP keys in AP mode
ones without a station pointer are default
keys, so don't check for AP mode here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The nl80211 documentation is currently never
generated, so problems have accumulated. Fix
most of the trivial ones.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix a small problem in the documentation for
ieee80211_request_smps, and a now erroneous
inclusion of enum ieee80211_key_alg, which no
longer exists after the change to ciphers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>