Add the mdio bus and the phy to the fec-node.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7 ("pinctrl: imx: Allow parsing DT without
function nodes").
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Specify 'vdd' and 'vddio' supplies for accelerometer to avoid warnings
during boot.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/iio/accel/mma8452.txt,
the correct interrupt-names are "INT1" and "INT2", so fix them
accordingly.

While at it, modify the node to only specify "INT2" since providing
two interrupts is not necessary or useful (the driver will only use
one).
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[andrew.smirnov@gmail.com modified the patch to drop INT1]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch enables the recovery mode now available.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds missing i2c recovery modes and corrects wrongly named
ones.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6dl-yapp4 Draco and Ursa boards use the I2C3 bus to control some
external devices through the /dev files.

So enable the I2C3 bus on all board variants, not just on Hydra.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The second UART is needed for 3D or MFD printer control.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The pca9535 gpio expander is present on the Rex baseboard, but missing
from the dtsi.
The pca9535 is on i2c2 bus which is common to the three SOM
variants (Basic/Pro/Ultra), thus it is activated by default.

Add also the new gpio controller and the associated interrupt line
MX6QDL_PAD_NANDF_CS3__GPIO6_IO16.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Without configuring this pinctrl, the ID value can't be got correctly,
then, the dual-role switch can't work well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.

Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.

Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:

arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property

Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the touch keyboard present on Hydra board. The controller
is connected only using I2C lines. The interrupt line is not
available hence we use the polling mode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The device node name should reflect generic class of a device so rename
the "iram" node to "sram".  This will be also in sync with upcoming DT
schema.  No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

"internal_j8" and "internal_j9" are network interfaces that are not
exposed outside the board and were only ever used for debugging purposes.

Get rid of them as they are not needed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Wandboard devicetrees lack the ethernet PHY description, add it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the CAN enablement from SoM DTSi to board DTS, as each board might need
different CAN configuration. Moreover, disable CAN2 on the PDK2 as it is not
available on any connector. This also fixes on-SoM SD slot operation, as it
shares pins with the CAN2.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add "opp-suspend" property for i.MX7D to make sure system
suspend with max available opp.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 800MHz opp speed grading fuse mask should be 0xd instead
of 0xf according to fuse map definition:

SPEED_GRADING[1:0]	MHz
	00		800
	01		500
	10		1000
	11		1200
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.

Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:

arch/arm/boot/dts/imx6qdl-gw551x.dtsi:109.32-121.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property

Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass the memory unit name in order to fix the following build warning
with W=1:

arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi:23.9-26.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name

Cc: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Replace "simple-bus" with "simple-mfd" for anatop node in order
to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6sx.dtsi:603.31-616.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-1p1: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:618.31-631.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-3p0: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:633.31-646.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-2p5: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:648.32-663.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:665.33-679.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpcie: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:681.31-696.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc: missing or empty reg/ranges property

Based on a patch from Marco Felsch for the imx6qdl.dtsi.

Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add wdog1 node to support watchdog driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Pincfgs to enable the i.MX6's OTG feature for UDOO
Signed-off-by: Markus Kueffner <kueffner.markus@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the possibility to wake the module with an external signal
as defined in the Colibri standard
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.

Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.

This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Do not change the clock as the power for this phy is switched
with that clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds some missing pinmuxing that is in the colibri
standard to the dts.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit adds the touchscreen from Toradex so one can enable it.
It is disabled by default because the pins are also used for PWM<B>,
PWM<C>, aka pwm2, pwm3 which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch prepares the devicetree for the new Ixora V1.2 where we are
able to turn off the supply of the can transceiver. This implies to use
a sleep state on transmission pins in order to prevent backfeeding.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the muxing for the optional pins usb-oc (overcurrent) and
usb-id.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add touch controller that is connected over an I2C bus.
It is disabled by default because the pins are also used for PWM,
which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add pinmuxing and do not specify voltage restrictions for the usdhc
instance available on the modules edge connector. This allows to use
SD-cards with higher transfer modes if supported by the carrier board.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add wakeup GPIO key which is able to wake the system from sleep
modes (e.g. Suspend-to-Memory).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the IMX7ULP reference manual, the mipi pll
clock comes from the MIPI PHY PLL output. So it should
not be defined as a fixed clock. So remove this clock
node and all the references to it.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LPUART driver does not support specifying "rs485-rts-delay"
property. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>