The U300 IRQs were bumped once to offset to 1 (in order to avoid
using IRQ 0 which is now NO_IRQ). This was OK as we were still
passing the number of irqs in the .nr_irqs field of the machine,
with descriptors allocated at boot time.

However .nr_irqs should be 0, leading the system to reserve the
first 16 IRQs. Then the VIC driver will complain that IRQs 1
thru 15 are pre-allocated, so to avoid this and use free
descriptors, move all IRQs up to offset 32.

This will all be done away with as we migrate to device tree,
so it is an interim solution.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Most of SPEAr SoCs, which support pinctrl, can configure & use
pads as gpio. This patch adds plgpio driver for configuring
these pads as gpio.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl subsystem needs gpio chip base to prepare set of gpio
pin ranges, which a given pinctrl driver can handle. This is
important to handle pinctrl gpio request calls in order to
program a given pin properly for gpio operation.

As gpio base is allocated dynamically during gpiochip
registration, presently there exists no clean way to pass this
information to the pinctrl subsystem.

After few discussions from [1], it was concluded that may be
gpio controller reporting the pin range it supports, is a
better way than pinctrl subsystem directly registering it.

[1] http://comments.gmane.org/gmane.linux.ports.arm.kernel/184816

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
[Edited documentation a bit]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts earlier commit which removed
pinctrl_remove_gpio_range(), because at that time there
weren't any more users of that routine. It was removed as the
removal of ranges was done in unregister of pinctrl.

But as we are now registering stuff from gpiolib, we may
remove and insert a gpio module multiple times. So, we
need this routine again.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The driver supports old up SiRFprimaII SoCs, this patch makes it support
the new SiRFmarco as well.
SiRFmarco, as a SMP SoC, adds new SIRFSOC_GPIO_PAD_EN_CLR registers, to
disable GPIO pad, we should write 1 to the corresponding bit in the new
CLEAR register instead of writing 0 to SIRFSOC_GPIO_PAD_EN.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Like the spear platform, the mvebu platform has multiple files: one
core file, and then one file per SoC family. More files will be added
later, as support for mach-orion5x and mach-mv78xx0 SoCs is added to
pinctrl-mvebu. For those reasons, having a separate subdirectory,
drivers/pinctrl/mvebu/ makes sense, and it had already been suggested
by Linus Wallej when the driver was originally submitted.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Including the core.h header for the pinctrl subsystem is not
necessary, and it is actually causing problems when moving the
pinctrl-mvebu drivers into a separate subdirectory.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mach-kirkwood and mach-dove architectures have not yet been
integrated into the mach-mvebu directory, which should ultimately
contain the support for all Marvell SoCs from the Engineering Business
Unit.

However, before this can happen, we need to let mach-kirkwood and
mach-dove use the pinctrl-mvebu driver, which supports the kirkwood
and dove SoC families. In order to do that, we make this driver
available as soon as PLAT_ORION is selected, instead of using
ARCH_MVEBU as a condition. In the long term, PLAT_ORION should
disappear and be fully replaced by ARCH_MVEBU, but the plan is to make
the migration step by step, by first having the existing mach-*
directories for Marvell SoCs converge on several infrastructures,
including the pinctrl one.

Also, like the spear pinctrl driver, we put all pinctrl-mvebu Kconfig
options under a if, in order to avoid having certain options
(PINCTRL_DOVE, PINCTRL_KIRKWOOD, etc.) selecting an option
(PINCTLR_MVEBU) which itself has a dependency (on ARCH_MVEBU). In this
a construct, the dependency is in fact ignored due to the selects.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This switches the way that pins are reserved for multiplexing:

We used to do this when the map was parsed, at the creation of
the settings inside the pinctrl handle, in pinmux_map_to_setting().

However this does not work for us, because we want to use the
same set of pins with different devices at different times: the
current code assumes that the pin groups in a pinmux state will
only be used with one single device, albeit different groups can
be active at different times. For example if a single I2C driver
block is used to drive two different busses located on two
pin groups A and B, then the pins for all possible states of a
function are reserved when fetching the pinctrl handle: the
I2C bus can choose either set A or set B by a mux state at
runtime, but all pins in both group A and B (the superset) are
effectively reserved for that I2C function and mapped to the
device. Another device can never get in and use the pins in
group A, even if the device/function is using group B at the
moment.

Instead: let use reserve the pins when the state is activated
and drop them when the state is disabled, i.e. when we move to
another state. This way different devices/functions can use the
same pins at different times.

We know that this is an odd way of doing things, but we really
need to switch e.g. an SD-card slot to become a tracing output
sink at runtime: we plug in a special "tracing card" then mux
the pins that used to be an SD slot around to the tracing
unit and push out tracing data there instead of SD-card
traffic.

As a side effect pinmux_free_setting() is unused but the stubs
are kept for future additions of code.

Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Jean Nicolas Graux <jean-nicolas.graux@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull networking fixes from David Miller:
 "Bug fixes galore, mostly in drivers as is often the case:

  1) USB gadget and cdc_eem drivers need adjustments to their frame size
     lengths in order to handle VLANs correctly.  From Ian Coolidge.

  2) TIPC and several network drivers erroneously call tasklet_disable
     before tasklet_kill, fix from Xiaotian Feng.

  3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
     fix from Cyril Brulebois.

  4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
     Nathan Walp.

  5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
     zero.  From John Fastabend.

  6) Fix smsc95xx tx checksum offload on big-endian, from Steve
     Glendinning.

  7) __inet_diag_dump() needs to repsect and report the error value
     returned from inet_diag_lock_handler() rather than ignore it.
     Otherwise if an inet diag handler is not available for a particular
     protocol, we essentially report success instead of giving an error
     indication.  Fix from Cyrill Gorcunov.

  8) When the QFQ packet scheduler sees TSO/GSO packets it does not
     handle things properly, and in fact ends up corrupting it's
     datastructures as well as mis-schedule packets.  Fix from Paolo
     Valente.

  9) Fix oopser in skb_loop_sk(), from Eric Leblond.

  10) CXGB4 passes partially uninitialized datastructures in to FW
      commands, fix from Vipul Pandya.

  11) When we send unsolicited ipv6 neighbour advertisements, we should
      send them to the link-local allnodes multicast address, as per
      RFC4861.  Fix from Hannes Frederic Sowa.

  12) There is some kind of bug in the usbnet's kevent deferral
      mechanism, but more immediately when it triggers an uncontrolled
      stream of kernel messages spam the log.  Rate limit the error log
      message triggered when this problem occurs, as sending thousands
      of error messages into the kernel log doesn't help matters at all,
      and in fact makes further diagnosis more difficult.

      From Steve Glendinning.

  13) Fix gianfar restore from hibernation, from Wang Dongsheng.

  14) The netlink message attribute sizes are wrong in the ipv6 GRE
      driver, it was using the size of ipv4 addresses instead of ipv6
      ones :-) Fix from Nicolas Dichtel."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  gre6: fix rtnl dump messages
  gianfar: ethernet vanishes after restoring from hibernation
  usbnet: ratelimit kevent may have been dropped warnings
  ipv6: send unsolicited neighbour advertisements to all-nodes
  net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
  usb: gadget: g_ether: fix frame size check for 802.1Q
  cxgb4: Fix initialization of SGE_CONTROL register
  isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
  cxgb4: Initialize data structures before using.
  af-packet: fix oops when socket is not present
  pkt_sched: enable QFQ to support TSO/GSO
  net: inet_diag -- Return error code if protocol handler is missed
  net: bnx2x: Fix typo in bnx2x driver
  smsc95xx: fix tx checksum offload for big endian
  rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
  ptp: update adjfreq callback description
  r8169: allow multicast packets on sub-8168f chipset.
  r8169: Fix WoL on RTL8168d/8111d.
  drivers/net: use tasklet_kill in device remove/close process
  tipc: do not use tasklet_disable before tasklet_kill

Pull sparc fixes from David Miller:
 "Several build/bug fixes for sparc, including:

  1) Configuring a mix of static vs.  modular sparc64 crypto modules
     didn't work, remove an ill-conceived attempt to only have to build
     the device match table for these drivers once to fix the problem.

     Reported by Meelis Roos.

  2) Make the montgomery multiple/square and mpmul instructions actually
     usable in 32-bit tasks.  Essentially this involves providing 32-bit
     userspace with a way to use a 64-bit stack when it needs to.

  3) Our sparc64 atomic backoffs don't yield cpu strands properly on
     Niagara chips.  Use pause instruction when available to achieve
     this, otherwise use a benign instruction we know blocks the strand
     for some time.

  4) Wire up kcmp

  5) Fix the build of various drivers by removing the unnecessary
     blocking of OF_GPIO when SPARC.

  6) Fix unintended regression wherein of_address_to_resource stopped
     being provided.  Fix from Andreas Larsson.

  7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
     Larsson."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
  sparc: Support atomic64_dec_if_positive properly.
  of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
  sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
  sparc: Add sparc support for platform_get_irq()
  sparc: Allow OF_GPIO on sparc.
  qlogicpti: Fix build warning.
  sparc: Wire up sys_kcmp.
  sparc64: Improvde documentation and readability of atomic backoff code.
  sparc64: Use pause instruction when available.
  sparc64: Fix cpu strand yielding.
  sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.

Pull cifs fixes from Jeff Layton.

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not lookup hashed negative dentry in cifs_atomic_open
  cifs: fix potential buffer overrun in cifs.idmap handling code

Pull arm64 fixes from Catalin Marinas:
 - correct argument type (pgprot_t) when calling __ioremap()
 - PCI_IOBASE virtual address change
 - use architected event for CPU cycle counter
 - fix ELF core dumping
 - select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
 - missing completion for secondary CPU boot
 - booting on systems with all memory beyond 4GB

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: mm: fix booting on systems with no memory below 4GB
  arm64: smp: add missing completion for secondary boot
  arm64: compat: select CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION
  arm64: elf: fix core dumping definitions for GP and FP registers
  arm64: perf: use architected event for CPU cycle counter
  arm64: Move PCI_IOBASE closer to MODULES_VADDR
  arm64: Use pgprot_t as the last argument when invoking __ioremap()

Merge tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fixes from Konrad Rzeszutek Wilk:
 "There are three ARM compile fixes (we forgot to export certain
  functions and if the drivers are built as an module - we go belly-up).

  There is also an mismatch of irq_enter() / exit_idle() calls sequence
  which were fixed some time ago in other piece of codes, but failed to
  appear in the Xen code.

  Lastly a fix for to help in the field with troubleshooting in case we
  cannot get the appropriate parameter and also fallback code when
  working with very old hypervisors."

Bug-fixes:
 - Fix compile issues on ARM.
 - Fix hypercall fallback code for old hypervisors.
 - Print out which HVM parameter failed if it fails.
 - Fix idle notifier call after irq_enter.

* tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/arm: Fix compile errors when drivers are compiled as modules (export more).
  xen/arm: Fix compile errors when drivers are compiled as modules.
  xen/generic: Disable fallback build on ARM.
  xen/events: fix RCU warning, or Call idle notifier after irq_enter()
  xen/hvm: If we fail to fetch an HVM parameter print out which flag it is.
  xen/hypercall: fix hypercall fallback code for very old hypervisors

We tried linking in a single built object to hold the device table,
but only works if all of the sparc64 crypto modules get built the same
way (modular vs. non-modular).

Just include the device ID stub into each driver source file so that
the table gets compiled into the correct result in all cases.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparc32 already supported it, as a consequence of using the
generic atomic64 implementation.  And the sparc64 implementation
is rather trivial.

This allows us to set ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE for all
of sparc, and avoid the annoying warning from lib/atomic64_test.c
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug-fix makes sure that of_address_to_resource is defined extern for sparc
so that the sparc-specific implementation of of_address_to_resource() is once
again used when including include/linux/of_address.h in a sparc context. A
number of drivers in mainline relies on this function working for sparc.

The bug was introduced in a850a755, "of/address:
add empty static inlines for !CONFIG_OF". Contrary to that commit title, the
static inlines are added for !CONFIG_OF_ADDRESS, and CONFIG_OF_ADDRESS is never
defined for sparc. This is good behavior for the other functions in
include/linux/of_address.h, as the extern functions defined in
drivers/of/address.c only gets linked when OF_ADDRESS is configured. However,
for of_address_to_resource there exists a sparc-specific implementation in
arch/sparc/arch/sparc/kernel/of_device_common.c

Solution suggested by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an irq is being unlinked concurrently with leon_handle_ext_irq,
irq_map[eirq] might be null in leon_handle_ext_irq. Make sure that
this is not dereferenced.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds sparc support for platform_get_irq that in the normal case use
platform_get_resource() to get an irq. This standard approach fails for sparc as
there are no resources of type IORESOURCE_IRQ for irqs for sparc.

Cross platform drivers can then use this standard platform function and work on
sparc instead of having to have a special case for sparc.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spotted after a code review.
Introduced by c12b395a (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.

For example:

	~# ifconfig eth0 down
	~# echo disk > /sys/power/state

	  <trigger a restore from hibernation>

	~# ifconfig eth0 up
	SIOCSIFFLAGS: No such device

This happens because the restore function bails out early upon
finding devices that were not up at hibernation.  In doing so,
it never gets to the netif_device_attach call at the end of
the restore function.  Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.

Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when something goes wrong, a flood of these messages can be
generated by usbnet (thousands per second).  This doesn't
generally *help* the condition so this patch ratelimits the
rate of their generation.

There's an underlying problem in usbnet's kevent deferral
mechanism which needs fixing, specifically that events *can*
get dropped and not handled.  This patch doesn't address this,
but just mitigates fallout caused by the current implemention.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

As documented in RFC4861 (Neighbor Discovery for IP version 6) 7.2.6.,
unsolicited neighbour advertisements should be sent to the all-nodes
multicast address.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes (again) from Dave Airlie:
 "dropped the ball on a vmware patch, so two more fixes for vmwgfx are
  here, one for hibernate issue, one for a BUG trigger."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix a case where the code would BUG when trying to pin GMR memory
  drm/vmwgfx: Fix hibernation device reset

Pull PCI fixes from Bjorn Helgaas:
 "Power management:
    - PCI/PM: Fix proc config reg access for D3cold and bridge
      suspending
    - PCI/PM: Resume device before shutdown
    - PCI/PM: Fix deadlock when unbinding device if parent in D3cold
  Hotplug:
    -  PCI/portdrv: Don't create hotplug slots unless port supports
       hotplug"

* tag '3.7-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/portdrv: Don't create hotplug slots unless port supports hotplug
  PCI/PM: Fix proc config reg access for D3cold and bridge suspending
  PCI/PM: Resume device before shutdown
  PCI/PM: Fix deadlock when unbinding device if parent in D3cold

Pull MMC fixes from Chris Ball:
 - sdhci: fix a NULL dereference at resume-time, seen on OLPC XO-4
 - sdhci: fix against 3.7-rc1 for UHS modes without a vqmmc regulator
 - sdhci-of-esdhc: disable CMD23 on boards where it's broken
 - sdhci-s3c: fix against 3.7-rc1 for card detection with runtime PM
 - dw_mmc, omap_hsmmc: fix potential NULL derefs, compiler warnings

* tag 'mmc-fixes-for-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: sdhci-s3c: fix the card detection in runtime-pm
  mmc: sdhci-s3c: use clk_prepare_enable and clk_disable_unprepare
  mmc: dw_mmc: constify dw_mci_idmac_ops in exynos back-end
  mmc: dw_mmc: fix modular build for exynos back-end
  mmc: sdhci: fix NULL dereference in sdhci_request() tuning
  mmc: sdhci: fix IS_ERR() checking of regulator_get()
  mmc: fix sdhci-dove probe/removal
  mmc: sh_mmcif: fix use after free
  mmc: sdhci-pci: fix 'Invalid iomem size' error message condition
  mmc: mxcmmc: Fix MODULE_ALIAS
  mmc: omap_hsmmc: fix NULL pointer dereference for dt boot
  mmc: omap_hsmmc: fix host reference after mmc_free_host
  mmc: dw_mmc: fix multiple drv_data NULL dereferences
  mmc: dw_mmc: enable controller interrupt before calling mmc_start_host
  mmc: sdhci-of-esdhc: disable CMD23 for some Freescale SoCs
  mmc: dw_mmc: remove _dev_info compile warning
  mmc: dw_mmc: convert the variable type of irq

Pull crypto fix from Herbert Xu:
 "This push fixes a potential panic in cryptd which may occur with
  crypto drivers such as aesni-intel."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: cryptd - disable softirqs in cryptd_queue_worker to prevent data corruption

Pull sound fixes from Takashi Iwai:
 "Most of commits are for stable and regression fixes.  Except for one
  fix for a regression in 3.7-rc4, there are all driver local changes,
  so nothing too much to worry."

* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: Fix card refcount unbalance
  ALSA: hda - Add new codec ALC668 and ALC900 (default name ALC1150)
  ALSA: hda - Improve HP depop when system enter to S3
  ALSA: usb-audio: Fix crash at re-preparing the PCM stream
  ALSA: hdspm - Fix sync check reporting on RME RayDAT
  ALSA: hda - Add pin fixups for ASUS G75
  ALSA: hda - Fix invalid connections in VT1802 codec
  ALSA: hda - Fix empty DAC filling in patch_via.c
  ALSA: hda - Force to reset IEC958 status bits for AD codecs
  ALSA: es1968: Add ESS vendor ID to pm_whitelist
  ALSA: HDA: Mark CS260x immutable structures const
  ALSA: HDA: Fix digital microphone on CS420x
  ALSA: hda: Cirrus: Fix coefficient index for beep configuration
  ALSA: hda - support Teradici 2200 host card audio
  ALSA: Fix typo in drivers sound

The commit 911dec0d
"xen/arm: Fix compile errors when drivers are compiled as modules." exports
the neccessary functions. But to guard ourselves against out-of-tree modules
and future drivers hitting this, lets export all of the relevant
hypercalls.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable@vger.kernel.org
Cc: linux-graphics-maintainer@vmware.com
Signed-off-by: Dave Airlie <airlied@redhat.com>

The device would not reset properly when resuming from hibernation.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable@vger.kernel.org
Cc: linux-graphics-maintainer@vmware.com
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'pinctrl-for-v3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl fixes from Linus Walleij:

 - A set of SPEAr pinctrl fixes that recently arrived

 - A fixup for the Samsung/Exynos Kconfig deps

* tag 'pinctrl-for-v3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: samsung and exynos need to depend on OF && GPIOLIB
  pinctrl: SPEAr1340: Add clcd sleep mode pin configuration
  pinctrl: SPEAr1340: Make DDR reset & clock pads as gpio
  pinctrl: SPEAr1310: add register entries for enabling pad direction
  pinctrl: SPEAr1310: Separate out pci pins from pcie_sata pin group
  pinctrl: SPEAr1310: Fix value of PERIP_CFG reigster and MCIF_SEL_SHIFT
  pinctrl: SPEAr1310: fix clcd high resolution pin group name
  pinctrl: SPEAr320: Correct pad mux entries for rmii/smii
  pinctrl: SPEAr3xx: correct register space to configure pwm
  pinctrl: SPEAr: Don't update all non muxreg bits on pinctrl_disable

Pull s390 fixes from Martin Schwidefsky:
 "A couple of bug fixes.  I keep the fingers crossed that we now got
  transparent huge pages ready for prime time."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/cio: fix length calculation in idset.c
  s390/sclp: fix addressing mode clobber
  s390: Move css limits from drivers/s390/cio/ to include/asm/.
  s390/thp: respect page protection in pmd_none() and pmd_present()
  s390/mm: use pmd_large() instead of pmd_huge()
  s390/cio: suppress 2nd path verification during resume

Pull HID fix from Jiri Kosina:
 "This reverts a patch that causes regression in binding between HID
  devices and drivers during device unplug/replug cycle."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hidraw: put old deallocation mechanism in place

Merge misc fixes from Andrew Morton:
 "Five fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (5 patches)
  h8300: add missing L1_CACHE_SHIFT
  mm: bugfix: set current->reclaim_state to NULL while returning from kswapd()
  fanotify: fix missing break
  revert "epoll: support for disabling items, and a self-test app"
  checkpatch: improve network block comment style checking

Pull drm fixes from Dave Airlie:
 "Just radeon and nouveau, mostly regressions fixers, and a couple of
  radeon register checker fixes."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: fix acpi edid retrieval
  drm/nvc0/disp: fix regression in vblank semaphore release
  drm/nv40/mpeg: fix context handling
  drm/nv40/graph: fix typo in type names
  drm/nv41/vm: fix typo in type name
  drm/radeon/si: add some missing regs to the VM reg checker
  drm/radeon/cayman: add some missing regs to the VM reg checker
  drm/radeon/dce3: switch back to old pll allocation order for discrete

Pull virtio and module fixes from Rusty Russell:
 "YA module signing build tweak, and two cc'd to stable."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  virtio: Don't access index after unregister.
  modules: don't break modules_install on external modules with no key.
  module: fix out-by-one error in kallsyms

Pull xfs bugfixes from Ben Myers:

 - fix for large transactions spanning multiple iclog buffers

 - zero the allocation_args structure on the stack before using it to
   determine whether to use a worker for allocation
 - move allocation stack switch to xfs_bmapi_allocate in order to
   prevent deadlock on AGF buffers

 - growfs no longer reads in garbage for new secondary superblocks

 - silence a build warning

 - ensure that invalid buffers never get written to disk while on free
   list

 - don't vmap inode cluster buffers during free

 - fix buffer shutdown reference count mismatch

 - fix reading of wrapped log data

* tag 'for-linus-v3.7-rc5' of git://oss.sgi.com/xfs/xfs:
  xfs: fix reading of wrapped log data
  xfs: fix buffer shudown reference count mismatch
  xfs: don't vmap inode cluster buffers during free
  xfs: invalidate allocbt blocks moved to the free list
  xfs: silence uninitialised f.file warning.
  xfs: growfs: don't read garbage for new secondary superblocks
  xfs: move allocation stack switch up to xfs_bmapi_allocate
  xfs: introduce XFS_BMAPI_STACK_SWITCH
  xfs: zero allocation_args on the kernel stack
  xfs: only update the last_sync_lsn when a transaction completes