- 20 May, 2011 40 commits
-
-
Jarod Wilson authored
Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jarod Wilson authored
Signed-off-by:
-
Antonio Ospite authored
The Kinect sensor is a device used by Microsoft for its Kinect project, which is a system for controller-less Human-Computer interaction targeted for Xbox 360. In the Kinect device, RGBD data is captured from two distinct sensors: a regular RGB sensor and a monochrome sensor which, with the aid of a IR structured light, captures what is finally exposed as a depth map; so what we have is basically a Structured-light 3D scanner. The Kinect gspca subdriver just supports the video stream for now, exposing the output from the RGB sensor or the unprocessed output from the monochrome sensor; it does not deal with the processed depth stream yet, but it allows using the sensor as a Webcam or as an IR camera (an external source of IR light might be needed for this use). The low level implementation is based on code from the OpenKinect project (http://openkinect.org). Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
Jean-François Moine <moinejf@free.fr> Signed-off-by:
-
Antonio Ospite authored
Add a 10 bits per pixel greyscale format in a bit-packed array representation, naming it Y10B. Such pixel format is supplied for instance by the Kinect sensor device. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Patrice Chotard authored
Signed-off-by:
Patrice CHOTARD <patricechotard@free.fr> Signed-off-by:
-
Patrice Chotard authored
Signed-off-by:
-
Patrice Chotard authored
Signed-off-by:
-
Patrice Chotard authored
Signed-off-by:
-
Patrice Chotard authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Antti Palosaari authored
Add some comments about known GPIO settings of supported board versions. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
After that Anysee I2C adapter is capable of one and two byte long I2C addresses in case of read from I2C bus. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Use correct I2C address for ZL10353 DVB-T demod. Signed-off-by:
-
Antti Palosaari authored
Looks like it is IF route switch on IOE[0]. Set it correctly to route signal from tuner to demod. Now it works for DVB-C too. Signed-off-by:
-
Antti Palosaari authored
It is ZL10353, TDA10023 and TDA18212. Tuner is inside of Samsung DNOD44CDH086A tuner module. Signed-off-by:
-
Antti Palosaari authored
New models have new NXP TDA18212 silicon tuner. Not tested yet due to lack of HW... Signed-off-by:
-
Antti Palosaari authored
Use board ID as base value when selecting correct hardware configuration. Signed-off-by:
-
Antti Palosaari authored
Print firmware version as two digit long (change from 3 to 2). Windows app have changed that too. First byte was hard coded as 0. Change email list address to report non-working device to current one. Signed-off-by:
-
Antti Palosaari authored
It can read more than one byte from I2C bus. Allow that. Signed-off-by:
-
Antti Palosaari authored
Switch from 8 bit notation to real 7 bit. Signed-off-by:
-
Antti Palosaari authored
New silicon tuner driver. Signed-off-by:
-
Andy Walls authored
Make a user visible driver version change, for the inevitable user support questions about why newer model HVR-1600's do not work with (older versions of) the cx18 driver. Signed-off-by:
Andy Walls <awalls@md.metrocast.net> Signed-off-by:
-
Andy Walls authored
A previous changes which added the newer model HVR-1600's and DTV support for them, neglected to add RF analog TV for them. Fix RF analog TV for the newer HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner and TDA8295 demodulator. Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and also to Mike Bradley for doing a lot of the legwork to figure out the tuner reset GPIO line, the demodulator I2C address, and that the GPIOs have to be reinitialized after a cardtype switch. Reported-by:
Jeff Campbell <jac1dlists@gmail.com> Tested-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
This was replaced by Micronas drxd driver Signed-off-by: -
Mauro Carvalho Chehab authored
There are still lots of 80-columns warnings and a few errors at some tables, but changing them would require more work and with probably not much gain. Signed-off-by: -
Mauro Carvalho Chehab authored
The macro is defined as: #define CHK_ERROR(s) if( (status = s)<0 ) break This sucks, as makes harder to debug if something got wrong and there are more than one level of loops. Also, violates CodingStyle. Fixed by this simple perl script: while (<>) { $f.=$_; }; $f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,; $f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g; $f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g; $f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g; $f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g; $f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g; $f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g; $f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g; print $f; Plus a few manual adjustments Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
This file is big. It has 12000+ lines! Most of the defined stuff aren't used anyware inside the driver, so we can just remove most of the lines and still keep everything that have any interest for the driver. If anyone ever need the other devices, it will be stored at git logs, so it is easy to recover. The diff result is impressive: 1 files changed, 1013 insertions(+), 12694 deletions(-) rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%) As a sideback effect, drxd driver will likely compile faster, and checkpatch.pl can run on this file without taking (literally) hours. The code cleanup was done using this small script: $ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols $ grep -f used_symbols drxd_map_firm.h >defines And then deleting the old #define lines, replacing by "defines" file content. Signed-off-by: -
Mauro Carvalho Chehab authored
s/(define\s+[^\s]+)\s........../\1/ Signed-off-by: -
Devin Heitmueller authored
Take a first cleanup pass over the sources to bring them closer to the Linux coding style. Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
Add support for the PCTV 330e remote control Signed-off-by:
-
Devin Heitmueller authored
Remove the flag indicating the 330e board is not validated, based on the half dozen users who have reported today that everything is working. Signed-off-by:
-
Devin Heitmueller authored
Abstract out the firmware for the drx-d so that it can be loaded by the request_firmware() interface. The firmware licensing permits free redistribution, and can be found here: http://kernellabs.com/firmware/drxdSigned-off-by:
-
Devin Heitmueller authored
Add the calls necessary to use the new drx-d driver for the PCTV 330e Signed-off-by:
-
Devin Heitmueller authored
Given how PCTV has multiple products with the same model name, include the model number in the description and #define to make it a little more clear. Signed-off-by:
-
