Add support for this new phy ID.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for this new phy ID.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel in general does not use &func referencing format.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: mark device as detached in PCI D3 and improve locking

Mark the netdevice as detached whenever parent is in PCI D3hot and not
accessible. This mainly applies to runtime-suspend state.
In addition take RTNL lock in suspend calls, this allows to remove
the driver-specific mutex and improve PM callbacks in general.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify rtl8169_runtime_resume() by calling rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the critical sections are protected with RTNL lock, we don't
need a separate mutex any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most relevant ops (open, close, ethtool ops) are protected with RTNL
lock by net core. Make sure that such ops can't be interrupted by
e.g. (runtime-)suspending by taking the RTNL lock in suspend ops
and the PCI error handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out bringing device up to a new function rtl8169_up(), similar
to rtl8169_down() for bringing the device down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the netdevice is marked as detached now when parent is not
accessible we can remove quite some checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark the netdevice as detached whenever we go into PCI D3hot.
This allows to remove some checks e.g. from ethtool ops because
dev_ethtool() checks for netif_device_present() in the beginning.

In this context move waking up the queue out of rtl_reset_work()
because in cases where netif_device_attach() is called afterwards
the queue should be woken up by the latter function only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A netdevice may be marked as detached because the parent is
runtime-suspended and not accessible whilst interface or link is down.
An example are PCI network devices that go into PCI D3hot, see e.g.
__igc_shutdown() or rtl8169_net_suspend().
If netdevice is down and marked as detached we can only open it if
we runtime-resume it before __dev_open() calls netif_device_present().

Therefore, if netdevice is detached, try to runtime-resume the parent
and only return with an error if it's still detached.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin Blumenstingl says:

====================
prepare dwmac-meson8b for G12A specific initialization

Some users are reporting that RGMII (and sometimes also RMII) Ethernet
is not working for them on G12A/G12B/SM1 boards. Upon closer inspection
of the vendor code for these SoCs new register bits are found.

It's not clear yet how these registers work. Add a new compatible string
as the first preparation step to improve Ethernet support on these SoCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Amlogic Meson G12A, G12B and SM1 have the same (at least as far as we
know at the time of writing) PRG_ETHERNET glue register implementation.
This implementation however is slightly different from AXG as it now has
an undocument "auto cali idx val" register in PRG_ETH1[17:16] which
seems to be related to RGMII Ethernet.

Add a new compatible string for G12A SoCs so the logic for this new
register can be implemented in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amlogic Meson G12A, G12B and SM1 have the same (at least as far as we
know at the time of writing) PRG_ETHERNET glue register implementation.
This implementation however is slightly different from AXG as it now has
an undocument "auto cali idx val" register in PRG_ETH1[17:16] which
seems to be related to RGMII Ethernet.

Add a compatible string for G12A and newer so the new registers can be
used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vasundhara Volam says:

====================
devlink: Add board.serial_number field to info_get cb.

This patchset adds support for board.serial_number to devlink info_get
cb and also use it in bnxt_en driver.

Sample output:

$ devlink dev info pci/0000:af:00.1
pci/0000:af:00.1:
  driver bnxt_en
  serial_number 00-10-18-FF-FE-AD-1A-00
  board.serial_number 433551F+172300000
  versions:
      fixed:
        board.id 7339763 Rev 0.
        asic.id 16D7
        asic.rev 1
      running:
        fw 216.1.216.0
        fw.psid 0.0.0
        fw.mgmt 216.1.192.0
        fw.mgmt.api 1.10.1
        fw.ncsi 0.0.0.0
        fw.roce 216.1.16.0

v2:
- Modify board_serial_number to board.serial_number for maintaining
consistency.
- Combine 2 lines in second patchset as column limit is 100 now
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add board.serial_number field info to info_get cb via devlink,
if driver can fetch the information from the device.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Board serial number is a serial number, often available in PCI
*Vital Product Data*.

Also, update devlink-info.rst documentation file.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Cosmetic cleanup in SJA1105 DSA driver

This removes the sparse warnings from the sja1105 driver and makes some
structures constant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since struct sja1105_private only holds a const pointer to one of these
structures based on device tree compatible string, the structures
themselves can be made const.

Also add an empty line between each structure definition, to appease
checkpatch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The per-chip instantiations of struct sja1105_table_ops and struct
sja1105_dynamic_table_ops can be made constant, so do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse is complaining and giving the following warning message:
'Using plain integer as NULL pointer'.

This is not what's going on, instead {0} is used as a zero initializer
for the structure members, to indicate that the particular chip revision
does not support those particular config tables.

But since the config tables are declared globally, the unpopulated
elements are zero-initialized anyway. So, to make sparse shut up, let's
remove the zero initializers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jonathan McDowell says:

====================
net: dsa: qca8k: Improve SGMII interface handling

This 3 patch series migrates the qca8k switch driver over to PHYLINK,
and then adds the SGMII clean-ups (i.e. the missing initialisation) on
top of that as a second patch. The final patch is a simple spelling fix
in a comment.

As before, tested with a device where the CPU connection is RGMII (i.e.
the common current use case) + one where the CPU connection is SGMII. I
don't have any devices where the SGMII interface is brought out to
something other than the CPU.

v5:
- Move spelling fix to separate patch
- Use ds directly rather than ds->priv
v4:
- Enable pcs_poll so we keep phylink updated when doing in-band
  negotiation
- Explicitly check for PHY_INTERFACE_MODE_1000BASEX when setting SGMII
  port mode.
- Address Vladimir's review comments
v3:
- Move phylink changes to separate patch
- Address rmk review comments
v2:
- Switch to phylink
- Avoid need for device tree configuration options
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch improves the handling of the SGMII interface on the QCA8K
devices. Previously the driver did no configuration of the port, even if
it was selected. We now configure it up in the appropriate
PHY/MAC/Base-X mode depending on what phylink tells us we are connected
to and ensure it is enabled.

Tested with a device where the CPU connection is RGMII (i.e. the common
current use case) + one where the CPU connection is SGMII. I don't have
any devices where the SGMII interface is brought out to something other
than the CPU.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the driver to use the new PHYLINK callbacks, removing the
legacy adjust_link callback.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jarod Wilson says:

====================
bonding: initial support for hardware crypto offload

This is an initial functional implementation for doing pass-through of
hardware encryption from bonding device to capable slaves, in active-backup
bond setups. This was developed and tested using ixgbe-driven Intel x520
interfaces with libreswan and a transport mode connection, primarily using
netperf, with assorted connection failures forced during transmission. The
failover works quite well in my testing, and overall performance is right
on par with offload when running on a bare interface, no bond involved.

Caveats: this is ONLY enabled for active-backup, because I'm not sure
how one would manage multiple offload handles for different devices all
running at the same time in the same xfrm, and it relies on some minor
changes to both the xfrm code and slave device driver code to get things
to behave, and I don't have immediate access to any other hardware that
could function similarly, but the NIC driver changes are minimal and
straight-forward enough that I've included what I think ought to be
enough for mlx5 devices too.

v2: reordered patches, switched (back) to using CONFIG_XFRM_OFFLOAD
to wrap the code additions and wrapped overlooked additions.
v3: rebase w/net-next open, add proper cc list to cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, this support is limited to active-backup mode, as I'm not sure
about the feasilibity of mapping an xfrm_state's offload handle to
multiple hardware devices simultaneously, and we rely on being able to
pass some hints to both the xfrm and NIC driver about whether or not
they're operating on a slave device.

I've tested this atop an Intel x520 device (ixgbe) using libreswan in
transport mode, succesfully achieving ~4.3Gbps throughput with netperf
(more or less identical to throughput on a bare NIC in this system),
as well as successful failover and recovery mid-netperf.

v2: just use CONFIG_XFRM_OFFLOAD for wrapping, isolate more code with it

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've been unable to get my hands on suitable supported hardware to date,
but I believe this ought to be all that is needed to enable the mlx5
driver to also work with bonding active-backup crypto offload passthru.

CC: Boris Pismenny <borisp@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Slave devices in a bond doing hardware encryption also need to be aware
that they're slaves, so we operate on the slave instead of the bonding
master to do the actual hardware encryption offload bits.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Acked-by: Jeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is prep work for initial support of bonding hardware encryption
pass-through support. The bonding driver will fill in the slave_dev
pointer, and we use that to know not to skb_push() again on a given
skb that was already processed on the bond device.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parav Pandit says:

====================
devlink: Support get,set mac address of a port function

Currently, ip link set dev <pfndev> vf <vf_num> <param> <value> has
below few limitations.

1. Command is limited to set VF parameters only.
It cannot set the default MAC address for the PCI PF.

2. It can be set only on system where PCI SR-IOV capability exists.
In smartnic based system, eswitch of a NIC resides on a different
embedded cpu which has the VF and PF representors for the SR-IOV
functions of a host system in which this smartnic is plugged-in.

3. It cannot setup the function attributes of sub-function described
in detail in comprehensive RFC [1] and [2].

This series covers the first small part to let user query and set MAC
address (hardware address) of a PCI PF/VF which is represented by
devlink port pcipf, pcivf port flavours respectively.

Whenever a devlink port manages a function connected to a devlink port,
it allows to query and set its hardware address.

Driver implements necessary get/set callback functions if it supports
port function for a given port type.

Patch summary:
Patch-1 Prepares devlink port fill routines for extack
Patch-2 and 3 extended devlink interface to get/set port function
attributes, mainly hardware address to start with.

Patch-2 Extended port dump command to query port function hardware
address
Patch-3 Introduces a command to set the hardware address of a port
function

Patch-4 to 9 refactors and implement devlink callbacks in mlx5_core
driver.
Patch-4 Constify the mac address pointer in set routines
Patch-5 Introduces eswich check helper to use in devlink facing
callbacks
Patch-6 Moves port index, port number conversion routine to eswitch
header file
Patch-7 Implements port function query devlink callback
Patch-8 Refactors mac address setting routine to uniformly use
state_lock
Patch-9 Implements port function set devlink callback

[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable user to set mac address of the PCI PF and VF port function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor mac address setting function to let caller hold the necessary
state_lock mutex, so that subsequent patch and use this helper routine.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support querying mac address of the eswitch devlink port function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To use port number to port index conversion at eswitch level, move it to
eswitch header.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce an helper routine to get esw from a devlink device and use it
at eswitch callbacks and in subsequent patch.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since none of the functions need to modify the input mac address,
constify them.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI PF and VF devlink port can manage the function represented by a
devlink port.

Allow users to set port function's hardware address.

Example of a PCI VF port which supports a port function:
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
  function:
    hw_addr 00:00:00:00:00:00

$ devlink port function set pci/0000:06:00.0/2 hw_addr 00:11:22:33:44:55

$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
  function:
    hw_addr 00:11:22:33:44:55
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI PF and VF devlink port can manage the function represented by
a devlink port.

Enable users to query port function's hardware address.

Example of a PCI VF port which supports a port function:
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
  function:
    hw_addr 00:11:22:33:44:66

$ devlink port show pci/0000:06:00.0/2 -jp
{
    "port": {
        "pci/0000:06:00.0/2": {
            "type": "eth",
            "netdev": "enp6s0pf0vf1",
            "flavour": "pcivf",
            "pfnum": 0,
            "vfnum": 1,
            "function": {
                "hw_addr": "00:11:22:33:44:66"
            }
        }
    }
}
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare devlink port related functions to optionally fill up
the extack information which will be used in subsequent patch by port
function attribute(s).
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>