Signed-off-by: Josua Mayer <josua@solid-run.com>

Add the necessary setup code to dpaa2-eth driver for controlling
link-status leds from the mac driver.
Signed-off-by: Josua Mayer <josua@solid-run.com>

To allow reliable link-status indication when exporting native
interfaces to dpdk, add support for controlling an LED to dpmac driver
link up- and down- functions.

Note that this is a hack and not a proper solution - with its own
particular shortcomings. Most notable is the lack of status indication
while Linux is controlling the interface through the dpaa2 ethernet
driver!
Signed-off-by: Josua Mayer <josua@solid-run.com>

LX2162A Clearfog support only covers 8x 1G rj45 + 2x 10G fixed-link sfp.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Note: To utilize this configuration DPL and DPC must be changed
accordingly to enable dpmac 13+14 for sgmii.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

make modules_install will not generate the module dependencies file if
the depmod command is missing from the running system.
Add it as a requirement to runme.sh and include in Dockerfile.
Signed-off-by: Josua Mayer <josua@solid-run.com>

The -E flag for sudo has previously been removed to work around some
strange issues.
Re-add the safer --preserve-envs flag listing all the settings currently
available.

This allows in particular to override the serdes configuration again
without editing the runme.sh file - e.g.:
docker run -i -t -v "$PWD":/work -e SERDES=8S_9_2 lx2160a_build -u 0 -g 0
Signed-off-by: Josua Mayer <josua@solid-run.com>

The hack for configuring MAC XIF_MODE register pending mc firmware
support differentiates between some 10gbps and some 1gbps modes.
Add rgmii modes to avoid fall-through when using the wired phy.
Signed-off-by: Josua Mayer <josua@solid-run.com>

i2c muxes are reset with cpu reset and will default back to channel 0,
while any other channel may still be blocked by a slave.
Detect known muxes and flush all their channels if detected.

Further disable detection logic because it missed rare cases.
Reset unconditionally instead.
Signed-off-by: Josua Mayer <josua@solid-run.com>

The i2c bus may be blocked by anz slave device if the system was reset
during a transaction, leading to ddr initialisation failures.
Implement a workaround releasing the bus by toggling scl 9 times.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Disable high-speed modes in Linux to ensure the microSD operates in the
same mode as it does during rcw and u-boot.

This is a work-around for when the system gets stuck after reset failing
to read from the microSD card.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Directly connect the sfp drivers's (sfp.c) link up and down events to an
LED node in device-tree. This solution is a workaround to the
shortcomings of the generic led triggers framework in combination with
multiple dynamic network interfaces, hot-pluggable phys (inside sfp
modules) and the dpaa2 driver in particular.
Signed-off-by: Josua Mayer <josua@solid-run.com>

The issue is that dpmac.16 to dpmac.18 links up, but unable to
communicate thru those ports.
This patch series does -
1. Fix dpmac.17 phy-handle type since by default the dpmac is RGMII, and
in half-twins case it is thru SGMII.
2. Add to the build script the usage of MC firmware 10.28.100; which is
based on 10.28.1 that fixes the tx/rx thru dpmac.16, dpmac.17 and
dpmac.18. This firmware is only for LSDK-21.08 and will be fixed in
later LSDK releases with newer MC firmwares.
3. Limit recycle queues in the half twins DPC to 1G; this makes it
possible for dpmac.18 to be able to transmit
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Half twins is 8xSFP+ and 8xSFP with OCPv3 NIC support board
2. Using SD1=8S (PLLF=100MHz, PLLS=161.132825MHz) runtime downgrade from
10G to 1G, according to SFP module inserted is not supported
3. Reverted default DDR speed to 3200
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Also fix buildroot compile error when running as root, and allow using a
local mirror.
Signed-off-by: Josua Mayer <josua@solid-run.com>

lx2160acex7: add support for SERDES1 mode 21, wich support 6x 25GB [Lanes 1-4 & Lane 7-8].
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>

- can work with podman
- added required packages
- allow using an apt proxy
Signed-off-by: Josua Mayer <josua@solid-run.com>

- Enabled CONFIG_SFP in the kernel build
- Pulled SFP device tree patch from mainline - this enables
dpmac7,8,9,10 that are the 4 SFP+ connectors on HoneyComb / ClearFog-CX
- Pulled AR8035 phy device tree patch
- Remove RTC interrupt from device tree
- Added power button support to device tree
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

This patch debootstraps debian bullseye under arm64 emulated buildroot
To build debian; run -

DISTRO=debian ./runme.sh
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

runme: check DDR speed before doing build

This patch adds most of the fixes to enable secure boot on the LX2160A
COM express -

1. The atf patches fixes the efuse fip fuse loading, and setting of ppwm
register and then gpio handling
2. The u-boot patches adds the secureboot defconfig, and then SVR_WO_E
mask fix
3. Patches for runme.sh script; for building the secure image run with
'SECURE=true ./runme.sh'

The missing piece is u-boot esbc validate code that completes the chain
of trust boot (COT).
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>