This patch adds support to remote checksum checksum offload
to VXLAN. This patch adds remcsumtx and remcsumrx to ip vxlan
configuration to enable remote checksum offload for transmit
and receive on the VXLAN tunnel.

https://tools.ietf.org/html/draft-herbert-vxlan-rco-00

Example:

ip link add name vxlan0 type vxlan id 42 group 239.1.1.1 dev eth0 \
    udpcsum remcsumtx remcsumrx

Testing:

Ran single netperf over mlnx4 to illustrate the effest:

- Without RCO (UDP csum set to zero)
  4335.99 Mbps
- With RCO enabled
  7661.81 Mbps
Signed-off-by: Tom Herbert <tom@herbertland.com>

fgets() will read at most size-1 bytes into the buffer and add a
terminating null-char at the end. Therefore it is not necessary to pass
a reduced buffer size when calling it.

This change was generated using the following semantic patch:

@@
identifier buf, fp;
@@
- fgets(buf, sizeof(buf) - 1, fp)
+ fgets(buf, sizeof(buf), fp)
Signed-off-by: Phil Sutter <phil@nwl.cc>

Although not fundamentally necessary to check return codes in these
spots, preventing the warnings will put new ones into focus.
Signed-off-by: Phil Sutter <phil@nwl.cc>

No need to keep static port boundaries global, they are not used
directly. Keeping them local also allows to safely reduce their names to
the minimum. Assign hardcoded fallback values also if fscanf() fails.
Get rid of unnecessary braces around return parameter.

Instead of more or less duplicating is_ephemeral() in run_ssfilter(),
simply call the function instead.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Exit early or continue on error instead of putting conditional into
conditional to make reading the code a bit easier.

Also, the call to memcpy() can be skipped by initialising prog with the
desired prefix.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Instead of calling rewind() and fgets() before every call to
scan_lines(), move them into scan_lines() itself.

This should also fix compat mode, as before the second call to
scan_lines() the first line was skipped unconditionally.
Signed-off-by: Phil Sutter <phil@nwl.cc>

- Replace commas at end of subsection with dots.
- Replace double whitespace by single one.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Technically, the range of possible hoplimit values are defined by IPv4
and IPv6 header formats. Both define the field to be eight bits in size,
which leads to a value range of [0;255]. Setting a packet's hoplimit
field to 0 though makes not much sense, as the next hop would
immediately drop the packet. Therefore Linux uses 0 as a special value
indicating to use the system's default hoplimit (configurable via
sysctl). In iproute, setting the hoplimit of a route to 0 is equivalent
to omitting the hoplimit parameter alltogether, so it is actually not
necessary to allow that value to be specified, but keep it anyway for
backwards compatibility.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Since it uses only a single filter, rtnl_dump_filter() can be used.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Right after ipaddr_reset_filter(), filter.family is always AF_UNSPEC.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Linux version 3.1 introduced a consistency check for netlink dumps in
commit 670dc28 ("netlink: advertise incomplete dumps"). This bites
iproute2 when flushing more addresses than can fit into a single
RTM_GETADDR response. To silence the spurious error message "Dump was
interrupted and may be inconsistent.", advise rtnl_dump_filter_l() to
not care about NLM_F_DUMP_INTR.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Allow for a filter to ignore certain nlmsg_flags.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Since it's no longer relevant whether an IP address is primary or
secondary when flushing, ipaddr_flush() can be simplified a bit.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Cleanup all checkpatch complaints about whitespace in rt_names.

Add support for reading table id/name mappings from rt_tables.d
directory.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

I found recently that, if I disabled address promotion in the kernel, that
ip addr flush dev <dev>

would fail with an EADDRNOTAVAIL errno (though the flush operation would in fact
flush all addresses from an interface properly)

Whats happening is that, if I add a primary and multiple secondary addresses to
an interface, the flush operation first ennumerates them all with a GETADDR |
DUMP operation, then sends a delete request for each address.  But the kernel,
having promotion disabled, deletes all secondary addresses when the primary is
removed.  That means, that several delete requests may still be pending in the
netlink request for addresses that have been removed on our behalf, resulting in
EADDRNOTAVAIL return codes.

It seems the simplest thing to do is to understand that EADDRUNAVAIL isn't a
fatal outcome on a flush operation, as it just indicates that an address which
you want to remove is already removed, so it can safely be ignored.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>

Despite commit 45a82e5 ("iproute vxlan add support for fdb replace
command"), the 'fdb replace' command was not mentioned in bridge.8.
Signed-off-by: Phil Sutter <phil@nwl.cc>

The algorithm depends on the loop counter ('i') to increment by one in
each iteration. Though if running endlessly (count==0), the counter was
not incremented at all.

Also change formatting of the header printing conditional a bit so it's
hopefully easier to read.

Fixes: e7e2913f ("lnstat: run indefinitely by default")
Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>

Post merge window changes

- Drop 'extern' keyword from all function prototypes.
- Make line breaking of print_* functions consistent.
- Make print_ntable() and ipntable_reset_filter() static and remove
  their declaration.
- Drop declaration of non-existent ipaddr_list() and iproute_monitor().
Signed-off-by: Phil Sutter <phil@nwl.cc>

Remove extraneous whitespace

Signed-off-by: Ville Skyttä <ville.skytta@iki.fi>

Fix syntax issues and warnings highlighted by `man --warnings=w' from
man-db 2.7.1.
Signed-off-by: Ville Skyttä <ville.skytta@iki.fi>

Signed-off-by: Phil Sutter <phil@nwl.cc>

Since p->name is only IFNAMSIZ bytes, do not copy more than IFNAMSIZ - 1
bytes into it so there remains at least a single null byte in the end.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>

Instead of parsing an unsigned integer and checking boundaries, simply
parse u8. This and the added ttl alias 'hlim' provide consistency with
ip6tunnel.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>

This makes output consistent with iptunnel, also supporting reverse DNS
lookup for remote address if requested.
Signed-off-by: Phil Sutter <phil@nwl.cc>

In iptunnel, declare loop variables inside the loop as done in
ip6tunnel.

Fix and simplify goto logic in ip6tunnel:
- Failure to read over header lines would have left fp opened.
- By returning directly upon fopen() failure, fp can be closed
  unconditionally in the end.

Use the same goto logic in iptunnel, as well.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Although the cache is only initialized in do_show(), this way it is at
least consistent with ip6tunnel.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Make ip6tunnel print an error message as well. While there, get rid of
unnecessary line breaking.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Instead of duplicating the same code six times (key, ikey and okey in
iptunnel and ip6tunnel), have a common parsing routine. This has the
added benefit of having the same verbose error message in ip6tunnel as
well as iptunnel.

I'm not sure if parsing an IPv4 address as key makes sense for
ip6tunnel, but the code was there before so this patch at least doesn't
make it worse.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Put whitespace in the beginning of optional parts, not as suffix
anywhere. Also drop double whitespaces in between words.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Use PKG_CONFIG from Config - it works better when cross-compiling.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>