Added new option 'type' to 'ip link show'
command which allows to filter devices by type:

    ip link show type bridge
    ip link show type vlan
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Sometimes it's needed to have "ip address show" list only addresses
with certain flags not being set, e.g. in network scripts.
As an example one might want to exclude addresses in "tentative"
or "deprecated" state.

Support listing addresses with flags tentative, deprecated, dadfailed
not being set by prefixing the respective flag with a minus.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

Added another timestamp format to look like more logging info:

[2014-12-22T22:36:50.489 ] 2: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default
    link/ether 3c:97:0e:a3:86:2e brd ff:ff:ff:ff:ff:ff
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Remove all trailing whitespace and space before tabs.

Checking by SS_CLOSE state was remowed in:

    (45a4770b) ss: Remove checking SS_CLOSE state for packet and netlink

which is not really correct because now by default all sockets are seen
when do 'ss'.

Here is most correct fix which considers specified family.

To see netlink sockets:
    ss -A netlink

To see packet sockets:
    ss -A packet

And ss by default will show only connected/established sockets as it
was before all the time.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Replaced handling netlink messages by rtnl_dump_filter
from lib/libnetlink.c, also:

    - removed unused dump_fp arg;
    - added MAGIC_SEQ #define for 123456 seq id;
    - silently exit if ENOENT errno is caused for NETLINK_SOCK_DIAG proto
        in lib/libnetlink.c: rtnl_duml_filter_l(...) function. This fix
        was added in a3fd8e58 by Eric
        for misc/ss.c
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Go back to kernel version of if_bridge.h and use patched
version of linux/in6.h and libc-compat.h

Needs to be built at runtime.

Now it is posible to filter by existing Netlink protos:

    ss -A netlink src uevent
    ss -A netlink src nft
    ss -A netlink src genl
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

This patch makes CAN_CTRLMODE_PRESUME_ACK netlink feature configurable.
When enabled, the feature sets CAN controller in mode in which
acknowledgement absence is ignored.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>

On Fri, 2014-12-05 at 17:13 -0800, Eric Dumazet wrote:

> I guess we could count number of spaces/fields in both lines,
> and disable the iproute2 trick if counts match.

Something like that maybe ?

 misc/nstat.c |   18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)
Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com>

This patch fixes the following issues which was introduced by me in commits:

    #1 (2dc85485) ss: Fixed broken output for Netlink 'Peer Address:Port' column
    ISSUE: Broken layout when all sockets are printed out

    #2 (eef43b50) ss: Identify more netlink protocol names
    ISSUE: Protocol id is not printed if 'numbers only' output was specified (-n)

Also aligned the width of the local/peer ports to be more wider.

I tested with a lot of option combinations (I may miss some test cases),
but layout seems to me better than the previous released version of iproute2/ss.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Adding in6.h breaks build with redefined values.

The issue was observed when IPv6 router broadcasted NDUSEROPT
messages which are not handled by monitor and caused printing
'Timestamps' w/o message because such kind of rtnl messages is not
handled by monitor.

As 'ip monitor' by default subscribes to the all mcast rtnl groups except
RTGRP_TC then all messages of these rtnl groups which are not handled by
monitor may cause such issues.

Fixed by subscribing by default to rtnl mcast groups which are
supported by 'ip monitor'.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

This option was used only for 'ip link', but it can be useful to have it for
'ip address'. Thus it is possible to display link details and addresses with one
command.

Example:
$ ip -d a ls dev gre1
9: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1468 qdisc noqueue state UNKNOWN group default
    link/gre 10.16.0.249 peer 10.16.0.121 promiscuity 0
    gre remote 10.16.0.121 local 10.16.0.249 ttl inherit ikey 0.0.0.10 okey 0.0.0.10 icsum ocsum
    inet 192.168.0.249 peer 192.168.0.121/32 scope global gre1
       valid_lft forever preferred_lft forever
    inet6 fe80::5efe:a10:f9/64 scope link
       valid_lft forever preferred_lft forever
Suggested-by: Christophe Gouault <christophe.gouault@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>

The header wars continue...

Need this header file to avoid build issues on older systems
like Debian 7

Missing "

Add ESP to decode switch.

RFC 2598 defines Expedited Forwarding in section 2.3
   Codepoint 101110 is recommended for the EF PHB.
which translates to B8 as encoded in rt_dsfield

BEFORE:
              The show command has additional formatting options:

       -s, -stats, -statistics
              output more statistics about packet usage.

       -d, -details
              output more detailed information.

       -h, -human, -human-readble
              output statistics with human readable values number followed by suffix

       -iec   print human readable rates in IEC units (ie. 1K = 1024).
AFTER:
       The show command has additional formatting options:

              -s, -stats, -statistics
                     output more statistics about packet usage.

              -d, -details
                     output more detailed information.

              -h, -human, -human-readble
                     output statistics with human readable values number followed by suffix

              -iec   print human readable rates in IEC units (ie. 1K = 1024).
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Just print the help when "ip route del" is called without any other
arguments.

Resolves:

 * https://bugzilla.redhat.com/show_bug.cgi?id=997965Signed-off-by: Pavel Šimerda <psimerda@redhat.com>

Added checking existence of the doc files converters.
If the XXX tool exists then HAVE_XXX:=y will be written
to the Config file. Example of the configure script output:

TC schedulers
 ATM	no
 IPT	using xtables
 IPSET  yes

iptables modules directory: /usr/lib/iptables
libc has setns: yes
SELinux support: no

Docs
 latex: no
 WARNING: no docs can be built from LaTeX files
 sgml2html: yes
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Use current upstream header.

Get rid of self-handling and creating of Netlink socket for show packet
socket stats.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Added 'master' option to 'ip link show' command
to filter devices by master dev.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

When output the netlink sockets:

    ss -A netlink state close

the layout is a little broken with a shifted 'Peer Address:Port'
stars and empty new lines. Fixed by making the port field to be
wider for 'Local Address:Port' column.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

I dont see a reason that packet and netlink states will be
printed only if SS_CLOSE state is set in filter, in that case
to print states of netlink or packet sockets it is needed to run:

    ss -A netlink state close

instead of:

    ss -A netlink
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

As 'ip' util will share the same netns from the caller
process then we can just look at /proc/self/.. to show
the netns of the current process by:

    ip netns id
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

With this change the results of tc tests will be recorded under:

    testsuite/results/tc/

The ip related tests can be added under:

    testsuite/tests/ip
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Added 'dev' option to allow filtering events by device.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

There were only few Netlink protocol names
which were printed on the screen:

    rtnl, fw, tcpdiag

So added the ability to identify Netlink proto name
from /etc/iproute/nl_protos or from static table.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>

Add udpcsum option to enable transmitting UDP checksums when doing
VXLAN/IPv4. Add udp6zerocsumtx, and udp6zerocsumrx options to enable
sending zero checksums and receiving zero checksums in VXLAN/IPv6.
Signed-off-by: Tom Herbert <therbert@google.com>