As Jamal pointed out, there are two different approaches to bandwidth
measurement. Try to make this clear by separating them in synopsis and
also documenting the way to fine-tune avrate.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

As Jamal suggested, BRANCH is the wrong name, as these keywords go
beyond simple branch control - e.g. loops are possible, too. Therefore
rename the non-terminal to CONTROL instead which should be more
appropriate.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

This is not a full test, since kernel functionality is not actually
tested. It only compares that the kernel returned values when listing
the action are what one expects them to be.

Since this test succeeded on both a little-endian and a big-endian
system, it shows that any endianness issues have been resolved in
tc/p_ip.c at least.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

The retain value was wrong for u16 and u8 types.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

This was tricky to get right:
- The 'stride' value used for 8 and 16 bit values must behave inverse to
  the value's intra word offset to work correctly with big-endian data
  act_pedit is editing.
- The 'm' array's values are in host byte order, so they have to be
  converted as well (and the ordering was just inverse, for some
  reason).
- The only sane way of getting this right is to manipulate value/mask in
  host byte order and convert the output.
- TIPV4 (i.e. 'munge ip src/dst') had it's own pitfall: the address
  parser converts to network byte order automatically. This patch fixes
  this by converting it back before calling pack_key32, which is a hack
  but at least does not require to implement a completely separate code
  flow.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

Break overlong function definitions and remove one extraneous
whitespace.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>

Add support for ignore route attribute, and refine the code to use
rta_getattr_* function to get attribute value.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>

Update this manual to add attributes proxy_neigh and
ignore_routes_with_linkdown.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>

The number of casts in macro was excessive.

More checkpatch spring cleaning

Use checkpatch auto fix to cleanup lingering style issues

Run all the ip code through checkpatch and have it fix the obvious stuff.

Use checkpatch to fix whitespace and other style issues.

Signed-off-by: Luca Lemmo <luca@linux.com>

Signed-off-by: Luca Lemmo <luca@linux.com>

Signed-off-by: Luca Lemmo <luca@linux.com>

Recently a new temp router port mode was added and with it the dumped
information was extended similar to how mdb entries were done. This
patch adds support to dump the new information by using the "-s" switch.
Example:
$ bridge -d -s mdb show
dev br0 port eth1 grp ff02::1:ffbf:5716 temp 234.39
dev br0 port eth1 grp 239.0.0.2 temp  97.17
dev br0 port eth1 grp 239.0.0.3 temp 105.36
router ports on br0: eth1    0.00 permanent
router ports on br0: eth2  254.87 temp

It also updates the bridge man page.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>

Since the IP Header Length field is just half a byte, adjust retain to
only match these bits so the Version field is not overwritten by
accident.

The whole concept is actually broken due to dependency on endianness
which pedit ignores.
Signed-off-by: Phil Sutter <phil@nwl.cc>

This was horribly broken:
* pack_key8() and pack_key16() ...
  * missed to invert retain value when applying it to the mask,
  * did not sanitize val by ANDing it with retain,
  * and ignored the mask which is necessary for 'invert' command.
* pack_key16() did not convert mask to network byte order.
* Changing the retain value for 'invert' or 'retain' operation seems
  just plain wrong.
* While here, also got rid of unnecessary offset sanitization in
  pack_key32().
* Simplify code a bit by always assigning the local mask variable to
  tkey->mask before calling any of the pack_key*() variants.
Signed-off-by: Phil Sutter <phil@nwl.cc>

After lookup of the layered op submodule, pedit would pass argv and argc
including the layered op identifier at first position which confused the
submodule parser. Fix this by calling NEXT_ARG() before calling the
parse_peopt() callback.
Signed-off-by: Phil Sutter <phil@nwl.cc>

There have been reports about 'ip addr' printing "Message truncated" on
systems with large numbers of VFs. Although I haven't been able to get
my hands on hardware suitable to reproduce this, increasing the dump
buffer has been reported to resolve the issue. For want of a better
idea, just double the buffer size to 32k.

Feels like this opportunistic buffer size selection is rather
workarounding a design flaw in libnetlink or maybe even the netlink
protocol itself.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Since the relevant code (and it's bugs) is identical in both files, fix
them in one go. This patch fixes multiple issues:

* Using 'int' for the 'tdiff' variable does not suffice on 64bit
  systems, the assigned initial time difference makes it wrap and
  contain a negative value afterwards. Instead use the more appropriate
  'time_t' type.

* As far as I understood the code, poll() is supposed to time out just
  at the right time to trigger update_db() in the configured interval.
  Therefore it's timeout must be set to the desired interval *minus* the
  time that has already passed since then.

* With the last change to the algorithm in place, it does not make sense
  to call update_db() before returning data to the connected client.
  Actually, it never does otherwise we could skip the periodic updates
  in the first place.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Mark MDB entries which are offloaded to HW with "offload" flag
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>

Signed-off-by: Phil Sutter <phil@nwl.cc>

To not make the output overly confusing, list them in a definition of
the STATE placeholder which is already used in the show/flush syntax but
wasn't explained before.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Not sure how useful they are in practice, but as 'ip neigh' supports
setting them all, they deserve to be described as well.

While at it, also add a missing layer of indentation to the subordinate
nud state list.
Signed-off-by: Phil Sutter <phil@nwl.cc>

The documentation is wrong here: it is indeed possible to remove policy
rule 0 and recreate it afterwards. Therefore remove these statements.
Signed-off-by: Phil Sutter <phil@nwl.cc>

While the synopsis section contains 'ip route list', it is later
described as 'ip route show'. Make this consistent by replacing 'list'
with 'show' in synopsis.
Signed-off-by: Phil Sutter <phil@nwl.cc>

This seems to have been a hidden feature, though it's very useful and
necessary at least when combining multiple pedit actions.
Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>

Signed-off-by: Phil Sutter <phil@nwl.cc>