Lookup function get_index() compares argument with table entries
only up to the length of the table entry so that if an entry
with lower index is a substring of a later one, earlier entry is
used even if the argument is equal to the other. For example,

  ip link set bond0 type bond xmit_hash_policy layer2+3

sets xmit_hash_policy to 0 (layer2) as this is found before
"layer2+3" can be checked.

Use strcmp() to compare whole strings instead.

v2: look for an exact match only
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>

Name of arp_all_targets parameter in output of "ip -d link show"
is missing trailing "s".

Fixes: 63d127b0 ("iproute2: finish support for bonding attributes")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>

This change enable the ss command to display the interface name as zone index
for local addresses when needed.

For this enhanced display *_diag stuff is needed.

It is based on a first version by Bernd Eckenfels.

example:
Netid  State   Recv-Q Send-Q                 Local Address:Port    Peer Address:Port
udp    UNCONN  0      0      fe80::20c:29ff:fe1f:7406%eth1:9999              :::*
udp    UNCONN  0      0                                 :::domain            :::*
tcp    LISTEN  0      3                                 :::domain            :::*
tcp    LISTEN  0      5      fe80::20c:29ff:fe1f:7410%eth2:99                :::*
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>

When requesting simultaneous output of TCP and UDP sockets
the netid field shows "tcp" always.

[root@xemvm1 iproute2]# ./misc/ss -a -tu
Netid State      Recv-Q Send-Q                            Local Address:Port                                Peer Address:Port
tcp   UNCONN     0      0                                             *:32713                                          *:*
tcp   UNCONN     0      0                                             *:bootpc                                         *:*
tcp   UNCONN     0      0                                            :::57879                                         :::*
tcp   LISTEN     0      128                                           *:ssh                                            *:*
tcp   ESTAB      0      48                                      1.2.3.5:ssh                                      1.2.3.4:45826
tcp   ESTAB      0      0                                       1.2.3.5:ssh                                      1.2.3.4:45814
tcp   LISTEN     0      128                                          :::ssh                                           :::*

While the 1st 3 sockets are UDP ones:

[root@xemvm1 iproute2]# ./misc/ss -a -u
State       Recv-Q Send-Q                              Local Address:Port                                  Peer Address:Port
UNCONN      0      0                                               *:32713                                            *:*
UNCONN      0      0                                               *:bootpc                                           *:*
UNCONN      0      0                                              :::57879                                           :::*
Reported-by: François-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Tested-by: François-Xavier Le Bail <fx.lebail@yahoo.com>

This patch allows adding the source-IP attribute to the netlink-command.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>

This patch allows to display the source-IP.
stype will be used in the next patch that allows to remove based on the
source-IP.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>

Renaming addr to daddr, because we will introduce saddr later.

The local variable is necessary to store RTA_PAYLOAD(a) temporarily.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>

Signed-off-by: Masatake YAMATO <yamato@redhat.com>

This adds the manpage for  PIE: Proportional Integral controller Enhanced AQM
scheme.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Vijay Subramanian <vijaynsu@cisco.com>
CC: Dave Taht <dave.taht@bufferbloat.net>

netem support 64bit rates start from linux-3.13.
Add 64bit rates support in tc tools.

tc qdisc show dev eth0
qdisc netem 1: dev eth4 root refcnt 2 limit 1000 rate 35Gbit

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Eric Dumazet <edumazet@google.com>

To avoid loss when transforming burst to buffer in userspace, send
burst/mtu to kernel directly.

Kernel commit 2e04ad424b("sch_tbf: add TBF_BURST/TBF_PBURST attribute")
make it can handle burst/mtu.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>

Signed-off-by: Thomas Haller <thaller@redhat.com>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>

This reverts commit 92deabcf.

Conflicts:
	ip/iplink_vxlan.c

Allow setting dst_port in 3.12

Add support for bonding attributes just added to net-next.
On set, allow string or number value for enumerated attributes.
On show, use always use string value for attribute.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>

Signed-off-by: Masatake YAMATO <yamato@redhat.com>

This patch enables -A unix_stream, -A unix_dgram and
-A unix_seqpacket option even if ss gets socket information
via netlink.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>

ss didn't distignish seqpacket type from dgram type.
With this patch ss can distignish it.

 $ misc/ss -x -a | grep seq
 u_seq  LISTEN     0      128    /run/udev/control 10966                 * 0
 u_seq  ESTAB      0      0                    * 115103                * 115104
 u_seq  ESTAB      0      0                    * 115104                * 115103
Signed-off-by: Masatake YAMATO <yamato@redhat.com>

Proportional Integral controller Enhanced (PIE) is a scheduler to address the
bufferbloat problem.

We present here a lightweight design, PIE(Proportional Integral controller
Enhanced) that can effectively control the average queueing latency to a target
value. Simulation results, theoretical analysis and Linux testbed results have
shown that PIE can ensure low latency and achieve high link utilization under
various congestion situations. The design does not require per-packet
timestamp, so it incurs very small overhead and is simple enough to implement
in both hardware and software.  "

For more information, please see technical paper about PIE in the IEEE
Conference on High Performance Switching and Routing 2013. A copy of the paper
can be found at ftp://ftpeng.cisco.com/pie/.

Please also refer to the IETF draft submission at
http://tools.ietf.org/html/draft-pan-tsvwg-pie-00

All relevant code, documents and test scripts and results can be found at
ftp://ftpeng.cisco.com/pie/.

For problems with the iproute2/tc or Linux kernel code, please contact Vijay
Subramanian (vijaynsu@cisco.com or subramanian.vijay@gmail.com) Mythili Prabhu
(mysuryan@cisco.com)
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Mythili Prabhu <mysuryan@cisco.com>
CC: Dave Taht <dave.taht@bufferbloat.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>

Signed-off-by: Pavel Emelyanov <xemul@paralles.com>

The vti interface will use GRE_KEY to match the right policy in kernel. So we
can not return fail when the tunnel is vti.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>

The RTM_NEWLINK message accepts ifi_index non-zero value and lets
creation of links with given index (if it's free, or course). This
functionality is available since linux-v3.5.

This patch makes this API available via ip tool.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>

attached.

cheers,
jamal
commit 58d78f9f6447df324cdeb99262442c5e3f1f924b
Author: Jamal Hadi Salim <jhs@mojatatu.com>
Date:   Sun Dec 22 10:34:18 2013 -0500

    dont skip displaying of action chains or lists by TCA_ACT_MAX_PRIO
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>

Attached.

cheers,
jamal
commit c5f30cabef14c951596210b96bc9b423b0d39592
Author: Jamal Hadi Salim <hadi@mojatatu.com>
Date:   Sun Dec 22 10:24:17 2013 -0500

    Allow batching of action gets
    Example:
    ----
    tc actions get \
    action gact index 100 \
    action gact index 4
    ----
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>

attached.

cheers,
jamal
commit d7869e6167c3553e93e254940b0647032b40fed8
Author: Jamal Hadi Salim <jhs@mojatatu.com>
Date:   Sun Dec 22 07:46:28 2013 -0500

    print new line at the end for aesthetics
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>

attached.

cheers,
jamal
commit b82057d9ec851a8aba8a295b959190ef5098f330
Author: Jamal Hadi Salim <jhs@mojatatu.com>
Date:   Sat Dec 21 17:00:11 2013 -0500

    After a decade of trying to deprecate the old policer syntax,
    I believe it is time to kill it. The kernel build option for old
    policer is gone for at least 5 years now (although backward
    compatibility is still there). Being backward compatible meant
    hijacking the keyword "action" and was obstructing policies like:

    tc filter add dev eth0 parent ffff: protocol ip pref 10 \
    u32 match ip protocol 1 0xff flowid 1:10 \
    action skbedit mark 1 \
    action police rate 10kbit burst 10k pipe \
    action skbedit mark 2 \
    action police rate 20kbit burst 20k pipe \
    action action mirred egress mirror dev dummy0
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>

skbedit should print the index and other generic metadata info
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>