Commit 03dcb90d authored by Jakub Kicinski's avatar Jakub Kicinski Committed by David S. Miller

net: appletalk: remove Apple/Farallon LocalTalk PC support

Looks like all the changes to this driver had been tree-wide
refactoring since git era begun. The driver is using virt_to_bus()
we should make it use more modern DMA APIs but since it's unlikely
to be getting any use these days delete it instead. We can always
revert to bring it back.
Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
Acked-by: default avatarArnd Bergmann <arnd@arndb.de>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e508af8a
......@@ -9,7 +9,6 @@ Contents:
:maxdepth: 2
cops
ltpc
.. only:: subproject and html
......
.. SPDX-License-Identifier: GPL-2.0
===========
LTPC Driver
===========
This is the ALPHA version of the ltpc driver.
In order to use it, you will need at least version 1.3.3 of the
netatalk package, and the Apple or Farallon LocalTalk PC card.
There are a number of different LocalTalk cards for the PC; this
driver applies only to the one with the 65c02 processor chip on it.
To include it in the kernel, select the CONFIG_LTPC switch in the
configuration dialog. You can also compile it as a module.
While the driver will attempt to autoprobe the I/O port address, IRQ
line, and DMA channel of the card, this does not always work. For
this reason, you should be prepared to supply these parameters
yourself. (see "Card Configuration" below for how to determine or
change the settings on your card)
When the driver is compiled into the kernel, you can add a line such
as the following to your /etc/lilo.conf::
append="ltpc=0x240,9,1"
where the parameters (in order) are the port address, IRQ, and DMA
channel. The second and third values can be omitted, in which case
the driver will try to determine them itself.
If you load the driver as a module, you can pass the parameters "io=",
"irq=", and "dma=" on the command line with insmod or modprobe, or add
them as options in a configuration file in /etc/modprobe.d/ directory::
alias lt0 ltpc # autoload the module when the interface is configured
options ltpc io=0x240 irq=9 dma=1
Before starting up the netatalk demons (perhaps in rc.local), you
need to add a line such as::
/sbin/ifconfig lt0 127.0.0.42
The address is unimportant - however, the card needs to be configured
with ifconfig so that Netatalk can find it.
The appropriate netatalk configuration depends on whether you are
attached to a network that includes AppleTalk routers or not. If,
like me, you are simply connecting to your home Macintoshes and
printers, you need to set up netatalk to "seed". The way I do this
is to have the lines::
dummy -seed -phase 2 -net 2000 -addr 2000.26 -zone "1033"
lt0 -seed -phase 1 -net 1033 -addr 1033.27 -zone "1033"
in my atalkd.conf. What is going on here is that I need to fool
netatalk into thinking that there are two AppleTalk interfaces
present; otherwise, it refuses to seed. This is a hack, and a more
permanent solution would be to alter the netatalk code. Also, make
sure you have the correct name for the dummy interface - If it's
compiled as a module, you will need to refer to it as "dummy0" or some
such.
If you are attached to an extended AppleTalk network, with routers on
it, then you don't need to fool around with this -- the appropriate
line in atalkd.conf is::
lt0 -phase 1
Card Configuration
==================
The interrupts and so forth are configured via the dipswitch on the
board. Set the switches so as not to conflict with other hardware.
Interrupts -- set at most one. If none are set, the driver uses
polled mode. Because the card was developed in the XT era, the
original documentation refers to IRQ2. Since you'll be running
this on an AT (or later) class machine, that really means IRQ9.
=== ===========================================================
SW1 IRQ 4
SW2 IRQ 3
SW3 IRQ 9 (2 in original card documentation only applies to XT)
=== ===========================================================
DMA -- choose DMA 1 or 3, and set both corresponding switches.
=== =====
SW4 DMA 3
SW5 DMA 1
SW6 DMA 3
SW7 DMA 1
=== =====
I/O address -- choose one.
=== =========
SW8 220 / 240
=== =========
IP
==
Yes, it is possible to do IP over LocalTalk. However, you can't just
treat the LocalTalk device like an ordinary Ethernet device, even if
that's what it looks like to Netatalk.
Instead, you follow the same procedure as for doing IP in EtherTalk.
See Documentation/networking/ipddp.rst for more information about the
kernel driver and userspace tools needed.
Bugs
====
IRQ autoprobing often doesn't work on a cold boot. To get around
this, either compile the driver as a module, or pass the parameters
for the card to the kernel as described above.
Also, as usual, autoprobing is not recommended when you use the driver
as a module. (though it usually works at boot time, at least)
Polled mode is *really* slow sometimes, but this seems to depend on
the configuration of the network.
It may theoretically be possible to use two LTPC cards in the same
machine, but this is unsupported, so if you really want to do this,
you'll probably have to hack the initialization code a bit.
Thanks
======
Thanks to Alan Cox for helpful discussions early on in this
work, and to Denis Hainsworth for doing the bleeding-edge testing.
Bradford Johnson <bradford@math.umn.edu>
Updated 11/09/1998 by David Huggins-Daines <dhd@debian.org>
......@@ -39,17 +39,6 @@ config DEV_APPLETALK
connect to the AppleTalk network, say Y.
config LTPC
tristate "Apple/Farallon LocalTalk PC support"
depends on DEV_APPLETALK && (ISA || EISA) && ISA_DMA_API && VIRT_TO_BUS
help
This allows you to use the AppleTalk PC card to connect to LocalTalk
networks. The card is also known as the Farallon PhoneNet PC card.
If you are in doubt, this card is the one with the 65C02 chip on it.
You also need version 1.3.3 or later of the netatalk package.
This driver is experimental, which means that it may not work.
See the file <file:Documentation/networking/device_drivers/appletalk/ltpc.rst>.
config COPS
tristate "COPS LocalTalk PC support"
depends on DEV_APPLETALK && ISA
......
......@@ -5,4 +5,3 @@
obj-$(CONFIG_IPDDP) += ipddp.o
obj-$(CONFIG_COPS) += cops.o
obj-$(CONFIG_LTPC) += ltpc.o
/*** ltpc.c -- a driver for the LocalTalk PC card.
*
* Copyright (c) 1995,1996 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
*
* This software may be used and distributed according to the terms
* of the GNU General Public License, incorporated herein by reference.
*
* This is ALPHA code at best. It may not work for you. It may
* damage your equipment. It may damage your relations with other
* users of your network. Use it at your own risk!
*
* Based in part on:
* skeleton.c by Donald Becker
* dummy.c by Nick Holloway and Alan Cox
* loopback.c by Ross Biro, Fred van Kampen, Donald Becker
* the netatalk source code (UMICH)
* lots of work on the card...
*
* I do not have access to the (proprietary) SDK that goes with the card.
* If you do, I don't want to know about it, and you can probably write
* a better driver yourself anyway. This does mean that the pieces that
* talk to the card are guesswork on my part, so use at your own risk!
*
* This is my first try at writing Linux networking code, and is also
* guesswork. Again, use at your own risk! (Although on this part, I'd
* welcome suggestions)
*
* This is a loadable kernel module which seems to work at my site
* consisting of a 1.2.13 linux box running netatalk 1.3.3, and with
* the kernel support from 1.3.3b2 including patches routing.patch
* and ddp.disappears.from.chooser. In order to run it, you will need
* to patch ddp.c and aarp.c in the kernel, but only a little...
*
* I'm fairly confident that while this is arguably badly written, the
* problems that people experience will be "higher level", that is, with
* complications in the netatalk code. The driver itself doesn't do
* anything terribly complicated -- it pretends to be an ether device
* as far as netatalk is concerned, strips the DDP data out of the ether
* frame and builds a LLAP packet to send out the card. In the other
* direction, it receives LLAP frames from the card and builds a fake
* ether packet that it then tosses up to the networking code. You can
* argue (correctly) that this is an ugly way to do things, but it
* requires a minimal amount of fooling with the code in ddp.c and aarp.c.
*
* The card will do a lot more than is used here -- I *think* it has the
* layers up through ATP. Even if you knew how that part works (which I
* don't) it would be a big job to carve up the kernel ddp code to insert
* things at a higher level, and probably a bad idea...
*
* There are a number of other cards that do LocalTalk on the PC. If
* nobody finds any insurmountable (at the netatalk level) problems
* here, this driver should encourage people to put some work into the
* other cards (some of which I gather are still commercially available)
* and also to put hooks for LocalTalk into the official ddp code.
*
* I welcome comments and suggestions. This is my first try at Linux
* networking stuff, and there are probably lots of things that I did
* suboptimally.
*
***/
/***
*
* $Log: ltpc.c,v $
* Revision 1.1.2.1 2000/03/01 05:35:07 jgarzik
* at and tr cleanup
*
* Revision 1.8 1997/01/28 05:44:54 bradford
* Clean up for non-module a little.
* Hacked about a bit to clean things up - Alan Cox
* Probably broken it from the origina 1.8
*
* 1998/11/09: David Huggins-Daines <dhd@debian.org>
* Cleaned up the initialization code to use the standard autoirq methods,
and to probe for things in the standard order of i/o, irq, dma. This
removes the "reset the reset" hack, because I couldn't figure out an
easy way to get the card to trigger an interrupt after it.
* Added support for passing configuration parameters on the kernel command
line and through insmod
* Changed the device name from "ltalk0" to "lt0", both to conform with the
other localtalk driver, and to clear up the inconsistency between the
module and the non-module versions of the driver :-)
* Added a bunch of comments (I was going to make some enums for the state
codes and the register offsets, but I'm still not sure exactly what their
semantics are)
* Don't poll anymore in interrupt-driven mode
* It seems to work as a module now (as of 2.1.127), but I don't think
I'm responsible for that...
*
* Revision 1.7 1996/12/12 03:42:33 bradford
* DMA alloc cribbed from 3c505.c.
*
* Revision 1.6 1996/12/12 03:18:58 bradford
* Added virt_to_bus; works in 2.1.13.
*
* Revision 1.5 1996/12/12 03:13:22 root
* xmitQel initialization -- think through better though.
*
* Revision 1.4 1996/06/18 14:55:55 root
* Change names to ltpc. Tabs. Took a shot at dma alloc,
* although more needs to be done eventually.
*
* Revision 1.3 1996/05/22 14:59:39 root
* Change dev->open, dev->close to track dummy.c in 1.99.(around 7)
*
* Revision 1.2 1996/05/22 14:58:24 root
* Change tabs mostly.
*
* Revision 1.1 1996/04/23 04:45:09 root
* Initial revision
*
* Revision 0.16 1996/03/05 15:59:56 root
* Change ARPHRD_LOCALTLK definition to the "real" one.
*
* Revision 0.15 1996/03/05 06:28:30 root
* Changes for kernel 1.3.70. Still need a few patches to kernel, but
* it's getting closer.
*
* Revision 0.14 1996/02/25 17:38:32 root
* More cleanups. Removed query to card on get_stats.
*
* Revision 0.13 1996/02/21 16:27:40 root
* Refix debug_print_skb. Fix mac.raw gotcha that appeared in 1.3.65.
* Clean up receive code a little.
*
* Revision 0.12 1996/02/19 16:34:53 root
* Fix debug_print_skb. Kludge outgoing snet to 0 when using startup
* range. Change debug to mask: 1 for verbose, 2 for higher level stuff
* including packet printing, 4 for lower level (card i/o) stuff.
*
* Revision 0.11 1996/02/12 15:53:38 root
* Added router sends (requires new aarp.c patch)
*
* Revision 0.10 1996/02/11 00:19:35 root
* Change source LTALK_LOGGING debug switch to insmod ... debug=2.
*
* Revision 0.9 1996/02/10 23:59:35 root
* Fixed those fixes for 1.2 -- DANGER! The at.h that comes with netatalk
* has a *different* definition of struct sockaddr_at than the Linux kernel
* does. This is an "insidious and invidious" bug...
* (Actually the preceding comment is false -- it's the atalk.h in the
* ancient atalk-0.06 that's the problem)
*
* Revision 0.8 1996/02/10 19:09:00 root
* Merge 1.3 changes. Tested OK under 1.3.60.
*
* Revision 0.7 1996/02/10 17:56:56 root
* Added debug=1 parameter on insmod for debugging prints. Tried
* to fix timer unload on rmmod, but I don't think that's the problem.
*
* Revision 0.6 1995/12/31 19:01:09 root
* Clean up rmmod, irq comments per feedback from Corin Anderson (Thanks Corey!)
* Clean up initial probing -- sometimes the card wakes up latched in reset.
*
* Revision 0.5 1995/12/22 06:03:44 root
* Added comments in front and cleaned up a bit.
* This version sent out to people.
*
* Revision 0.4 1995/12/18 03:46:44 root
* Return shortDDP to longDDP fake to 0/0. Added command structs.
*
***/
/* ltpc jumpers are:
*
* Interrupts -- set at most one. If none are set, the driver uses
* polled mode. Because the card was developed in the XT era, the
* original documentation refers to IRQ2. Since you'll be running
* this on an AT (or later) class machine, that really means IRQ9.
*
* SW1 IRQ 4
* SW2 IRQ 3
* SW3 IRQ 9 (2 in original card documentation only applies to XT)
*
*
* DMA -- choose DMA 1 or 3, and set both corresponding switches.
*
* SW4 DMA 3
* SW5 DMA 1
* SW6 DMA 3
* SW7 DMA 1
*
*
* I/O address -- choose one.
*
* SW8 220 / 240
*/
/* To have some stuff logged, do
* insmod ltpc.o debug=1
*
* For a whole bunch of stuff, use higher numbers.
*
* The default is 0, i.e. no messages except for the probe results.
*/
/* insmod-tweakable variables */
static int debug;
#define DEBUG_VERBOSE 1
#define DEBUG_UPPER 2
#define DEBUG_LOWER 4
static int io;
static int irq;
static int dma;
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/fcntl.h>
#include <linux/interrupt.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/spinlock.h>
#include <linux/in.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/if_arp.h>
#include <linux/if_ltalk.h>
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/atalk.h>
#include <linux/bitops.h>
#include <linux/gfp.h>
#include <net/Space.h>
#include <asm/dma.h>
#include <asm/io.h>
/* our stuff */
#include "ltpc.h"
static DEFINE_SPINLOCK(txqueue_lock);
static DEFINE_SPINLOCK(mbox_lock);
/* function prototypes */
static int do_read(struct net_device *dev, void *cbuf, int cbuflen,
void *dbuf, int dbuflen);
static int sendup_buffer (struct net_device *dev);
/* Dma Memory related stuff, cribbed directly from 3c505.c */
static unsigned long dma_mem_alloc(int size)
{
int order = get_order(size);
return __get_dma_pages(GFP_KERNEL, order);
}
/* DMA data buffer, DMA command buffer */
static unsigned char *ltdmabuf;
static unsigned char *ltdmacbuf;
/* private struct, holds our appletalk address */
struct ltpc_private
{
struct atalk_addr my_addr;
};
/* transmit queue element struct */
struct xmitQel {
struct xmitQel *next;
/* command buffer */
unsigned char *cbuf;
short cbuflen;
/* data buffer */
unsigned char *dbuf;
short dbuflen;
unsigned char QWrite; /* read or write data */
unsigned char mailbox;
};
/* the transmit queue itself */
static struct xmitQel *xmQhd, *xmQtl;
static void enQ(struct xmitQel *qel)
{
unsigned long flags;
qel->next = NULL;
spin_lock_irqsave(&txqueue_lock, flags);
if (xmQtl) {
xmQtl->next = qel;
} else {
xmQhd = qel;
}
xmQtl = qel;
spin_unlock_irqrestore(&txqueue_lock, flags);
if (debug & DEBUG_LOWER)
printk("enqueued a 0x%02x command\n",qel->cbuf[0]);
}
static struct xmitQel *deQ(void)
{
unsigned long flags;
int i;
struct xmitQel *qel=NULL;
spin_lock_irqsave(&txqueue_lock, flags);
if (xmQhd) {
qel = xmQhd;
xmQhd = qel->next;
if(!xmQhd) xmQtl = NULL;
}
spin_unlock_irqrestore(&txqueue_lock, flags);
if ((debug & DEBUG_LOWER) && qel) {
int n;
printk(KERN_DEBUG "ltpc: dequeued command ");
n = qel->cbuflen;
if (n>100) n=100;
for(i=0;i<n;i++) printk("%02x ",qel->cbuf[i]);
printk("\n");
}
return qel;
}
/* and... the queue elements we'll be using */
static struct xmitQel qels[16];
/* and their corresponding mailboxes */
static unsigned char mailbox[16];
static unsigned char mboxinuse[16] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
static int wait_timeout(struct net_device *dev, int c)
{
/* returns true if it stayed c */
/* this uses base+6, but it's ok */
int i;
/* twenty second or so total */
for(i=0;i<200000;i++) {
if ( c != inb_p(dev->base_addr+6) ) return 0;
udelay(100);
}
return 1; /* timed out */
}
/* get the first free mailbox */
static int getmbox(void)
{
unsigned long flags;
int i;
spin_lock_irqsave(&mbox_lock, flags);
for(i=1;i<16;i++) if(!mboxinuse[i]) {
mboxinuse[i]=1;
spin_unlock_irqrestore(&mbox_lock, flags);
return i;
}
spin_unlock_irqrestore(&mbox_lock, flags);
return 0;
}
/* read a command from the card */
static void handlefc(struct net_device *dev)
{
/* called *only* from idle, non-reentrant */
int dma = dev->dma;
int base = dev->base_addr;
unsigned long flags;
flags=claim_dma_lock();
disable_dma(dma);
clear_dma_ff(dma);
set_dma_mode(dma,DMA_MODE_READ);
set_dma_addr(dma,virt_to_bus(ltdmacbuf));
set_dma_count(dma,50);
enable_dma(dma);
release_dma_lock(flags);
inb_p(base+3);
inb_p(base+2);
if ( wait_timeout(dev,0xfc) ) printk("timed out in handlefc\n");
}
/* read data from the card */
static void handlefd(struct net_device *dev)
{
int dma = dev->dma;
int base = dev->base_addr;
unsigned long flags;
flags=claim_dma_lock();
disable_dma(dma);
clear_dma_ff(dma);
set_dma_mode(dma,DMA_MODE_READ);
set_dma_addr(dma,virt_to_bus(ltdmabuf));
set_dma_count(dma,800);
enable_dma(dma);
release_dma_lock(flags);
inb_p(base+3);
inb_p(base+2);
if ( wait_timeout(dev,0xfd) ) printk("timed out in handlefd\n");
sendup_buffer(dev);
}
static void handlewrite(struct net_device *dev)
{
/* called *only* from idle, non-reentrant */
/* on entry, 0xfb and ltdmabuf holds data */
int dma = dev->dma;
int base = dev->base_addr;
unsigned long flags;
flags=claim_dma_lock();
disable_dma(dma);
clear_dma_ff(dma);
set_dma_mode(dma,DMA_MODE_WRITE);
set_dma_addr(dma,virt_to_bus(ltdmabuf));
set_dma_count(dma,800);
enable_dma(dma);
release_dma_lock(flags);
inb_p(base+3);
inb_p(base+2);
if ( wait_timeout(dev,0xfb) ) {
flags=claim_dma_lock();
printk("timed out in handlewrite, dma res %d\n",
get_dma_residue(dev->dma) );
release_dma_lock(flags);
}
}
static void handleread(struct net_device *dev)
{
/* on entry, 0xfb */
/* on exit, ltdmabuf holds data */
int dma = dev->dma;
int base = dev->base_addr;
unsigned long flags;
flags=claim_dma_lock();
disable_dma(dma);
clear_dma_ff(dma);
set_dma_mode(dma,DMA_MODE_READ);
set_dma_addr(dma,virt_to_bus(ltdmabuf));
set_dma_count(dma,800);
enable_dma(dma);
release_dma_lock(flags);
inb_p(base+3);
inb_p(base+2);
if ( wait_timeout(dev,0xfb) ) printk("timed out in handleread\n");
}
static void handlecommand(struct net_device *dev)
{
/* on entry, 0xfa and ltdmacbuf holds command */
int dma = dev->dma;
int base = dev->base_addr;
unsigned long flags;
flags=claim_dma_lock();
disable_dma(dma);
clear_dma_ff(dma);
set_dma_mode(dma,DMA_MODE_WRITE);
set_dma_addr(dma,virt_to_bus(ltdmacbuf));
set_dma_count(dma,50);
enable_dma(dma);
release_dma_lock(flags);
inb_p(base+3);
inb_p(base+2);
if ( wait_timeout(dev,0xfa) ) printk("timed out in handlecommand\n");
}
/* ready made command for getting the result from the card */
static unsigned char rescbuf[2] = {LT_GETRESULT,0};
static unsigned char resdbuf[2];
static int QInIdle;
/* idle expects to be called with the IRQ line high -- either because of
* an interrupt, or because the line is tri-stated
*/
static void idle(struct net_device *dev)
{
unsigned long flags;
int state;
/* FIXME This is initialized to shut the warning up, but I need to
* think this through again.
*/
struct xmitQel *q = NULL;
int oops;
int i;
int base = dev->base_addr;
spin_lock_irqsave(&txqueue_lock, flags);
if(QInIdle) {
spin_unlock_irqrestore(&txqueue_lock, flags);
return;
}
QInIdle = 1;
spin_unlock_irqrestore(&txqueue_lock, flags);
/* this tri-states the IRQ line */
(void) inb_p(base+6);
oops = 100;
loop:
if (0>oops--) {
printk("idle: looped too many times\n");
goto done;
}
state = inb_p(base+6);
if (state != inb_p(base+6)) goto loop;
switch(state) {
case 0xfc:
/* incoming command */
if (debug & DEBUG_LOWER) printk("idle: fc\n");
handlefc(dev);
break;
case 0xfd:
/* incoming data */
if(debug & DEBUG_LOWER) printk("idle: fd\n");
handlefd(dev);
break;
case 0xf9:
/* result ready */
if (debug & DEBUG_LOWER) printk("idle: f9\n");
if(!mboxinuse[0]) {
mboxinuse[0] = 1;
qels[0].cbuf = rescbuf;
qels[0].cbuflen = 2;
qels[0].dbuf = resdbuf;
qels[0].dbuflen = 2;
qels[0].QWrite = 0;
qels[0].mailbox = 0;
enQ(&qels[0]);
}
inb_p(dev->base_addr+1);
inb_p(dev->base_addr+0);
if( wait_timeout(dev,0xf9) )
printk("timed out idle f9\n");
break;
case 0xf8:
/* ?? */
if (xmQhd) {
inb_p(dev->base_addr+1);
inb_p(dev->base_addr+0);
if(wait_timeout(dev,0xf8) )
printk("timed out idle f8\n");
} else {
goto done;
}
break;
case 0xfa:
/* waiting for command */
if(debug & DEBUG_LOWER) printk("idle: fa\n");
if (xmQhd) {
q=deQ();
memcpy(ltdmacbuf,q->cbuf,q->cbuflen);
ltdmacbuf[1] = q->mailbox;
if (debug>1) {
int n;
printk("ltpc: sent command ");
n = q->cbuflen;
if (n>100) n=100;
for(i=0;i<n;i++)
printk("%02x ",ltdmacbuf[i]);
printk("\n");
}
handlecommand(dev);
if (0xfa == inb_p(base + 6)) {
/* we timed out, so return */
goto done;
}
} else {
/* we don't seem to have a command */
if (!mboxinuse[0]) {
mboxinuse[0] = 1;
qels[0].cbuf = rescbuf;
qels[0].cbuflen = 2;
qels[0].dbuf = resdbuf;
qels[0].dbuflen = 2;
qels[0].QWrite = 0;
qels[0].mailbox = 0;
enQ(&qels[0]);
} else {
printk("trouble: response command already queued\n");
goto done;
}
}
break;
case 0Xfb:
/* data transfer ready */
if(debug & DEBUG_LOWER) printk("idle: fb\n");
if(q->QWrite) {
memcpy(ltdmabuf,q->dbuf,q->dbuflen);
handlewrite(dev);
} else {
handleread(dev);
/* non-zero mailbox numbers are for
commmands, 0 is for GETRESULT
requests */
if(q->mailbox) {
memcpy(q->dbuf,ltdmabuf,q->dbuflen);
} else {
/* this was a result */
mailbox[ 0x0f & ltdmabuf[0] ] = ltdmabuf[1];
mboxinuse[0]=0;
}
}
break;
}
goto loop;
done:
QInIdle=0;
/* now set the interrupts back as appropriate */
/* the first read takes it out of tri-state (but still high) */
/* the second resets it */
/* note that after this point, any read of base+6 will
trigger an interrupt */
if (dev->irq) {
inb_p(base+7);
inb_p(base+7);
}
}
static int do_write(struct net_device *dev, void *cbuf, int cbuflen,
void *dbuf, int dbuflen)
{
int i = getmbox();
int ret;
if(i) {
qels[i].cbuf = cbuf;
qels[i].cbuflen = cbuflen;
qels[i].dbuf = dbuf;
qels[i].dbuflen = dbuflen;
qels[i].QWrite = 1;
qels[i].mailbox = i; /* this should be initted rather */
enQ(&qels[i]);
idle(dev);
ret = mailbox[i];
mboxinuse[i]=0;
return ret;
}
printk("ltpc: could not allocate mbox\n");
return -1;
}
static int do_read(struct net_device *dev, void *cbuf, int cbuflen,
void *dbuf, int dbuflen)
{
int i = getmbox();
int ret;
if(i) {
qels[i].cbuf = cbuf;
qels[i].cbuflen = cbuflen;
qels[i].dbuf = dbuf;
qels[i].dbuflen = dbuflen;
qels[i].QWrite = 0;
qels[i].mailbox = i; /* this should be initted rather */
enQ(&qels[i]);
idle(dev);
ret = mailbox[i];
mboxinuse[i]=0;
return ret;
}
printk("ltpc: could not allocate mbox\n");
return -1;
}
/* end of idle handlers -- what should be seen is do_read, do_write */
static struct timer_list ltpc_timer;
static struct net_device *ltpc_timer_dev;
static netdev_tx_t ltpc_xmit(struct sk_buff *skb, struct net_device *dev);
static int read_30 ( struct net_device *dev)
{
lt_command c;
c.getflags.command = LT_GETFLAGS;
return do_read(dev, &c, sizeof(c.getflags),&c,0);
}
static int set_30 (struct net_device *dev,int x)
{
lt_command c;
c.setflags.command = LT_SETFLAGS;
c.setflags.flags = x;
return do_write(dev, &c, sizeof(c.setflags),&c,0);
}
/* LLAP to DDP translation */
static int sendup_buffer (struct net_device *dev)
{
/* on entry, command is in ltdmacbuf, data in ltdmabuf */
/* called from idle, non-reentrant */
int dnode, snode, llaptype, len;
int sklen;
struct sk_buff *skb;
struct lt_rcvlap *ltc = (struct lt_rcvlap *) ltdmacbuf;
if (ltc->command != LT_RCVLAP) {
printk("unknown command 0x%02x from ltpc card\n",ltc->command);
return -1;
}
dnode = ltc->dnode;
snode = ltc->snode;
llaptype = ltc->laptype;
len = ltc->length;
sklen = len;
if (llaptype == 1)
sklen += 8; /* correct for short ddp */
if(sklen > 800) {
printk(KERN_INFO "%s: nonsense length in ltpc command 0x14: 0x%08x\n",
dev->name,sklen);
return -1;
}
if ( (llaptype==0) || (llaptype>2) ) {
printk(KERN_INFO "%s: unknown LLAP type: %d\n",dev->name,llaptype);
return -1;
}
skb = dev_alloc_skb(3+sklen);
if (skb == NULL)
{
printk("%s: dropping packet due to memory squeeze.\n",
dev->name);
return -1;
}
skb->dev = dev;
if (sklen > len)
skb_reserve(skb,8);
skb_put(skb,len+3);
skb->protocol = htons(ETH_P_LOCALTALK);
/* add LLAP header */
skb->data[0] = dnode;
skb->data[1] = snode;
skb->data[2] = llaptype;
skb_reset_mac_header(skb); /* save pointer to llap header */
skb_pull(skb,3);
/* copy ddp(s,e)hdr + contents */
skb_copy_to_linear_data(skb, ltdmabuf, len);
skb_reset_transport_header(skb);
dev->stats.rx_packets++;
dev->stats.rx_bytes += skb->len;
/* toss it onwards */
netif_rx(skb);
return 0;
}
/* the handler for the board interrupt */
static irqreturn_t
ltpc_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
if (dev==NULL) {
printk("ltpc_interrupt: unknown device.\n");
return IRQ_NONE;
}
inb_p(dev->base_addr+6); /* disable further interrupts from board */
idle(dev); /* handle whatever is coming in */
/* idle re-enables interrupts from board */
return IRQ_HANDLED;
}
/***
*
* The ioctls that the driver responds to are:
*
* SIOCSIFADDR -- do probe using the passed node hint.
* SIOCGIFADDR -- return net, node.
*
* some of this stuff should be done elsewhere.
*
***/
static int ltpc_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
struct sockaddr_at *sa = (struct sockaddr_at *) &ifr->ifr_addr;
/* we'll keep the localtalk node address in dev->pa_addr */
struct ltpc_private *ltpc_priv = netdev_priv(dev);
struct atalk_addr *aa = &ltpc_priv->my_addr;
struct lt_init c;
int ltflags;
if(debug & DEBUG_VERBOSE) printk("ltpc_ioctl called\n");
switch(cmd) {
case SIOCSIFADDR:
aa->s_net = sa->sat_addr.s_net;
/* this does the probe and returns the node addr */
c.command = LT_INIT;
c.hint = sa->sat_addr.s_node;
aa->s_node = do_read(dev,&c,sizeof(c),&c,0);
/* get all llap frames raw */
ltflags = read_30(dev);
ltflags |= LT_FLAG_ALLLAP;
set_30 (dev,ltflags);
dev->broadcast[0] = 0xFF;
dev->addr_len=1;
dev_addr_set(dev, &aa->s_node);
return 0;
case SIOCGIFADDR:
sa->sat_addr.s_net = aa->s_net;
sa->sat_addr.s_node = aa->s_node;
return 0;
default:
return -EINVAL;
}
}
static void set_multicast_list(struct net_device *dev)
{
/* This needs to be present to keep netatalk happy. */
/* Actually netatalk needs fixing! */
}
static int ltpc_poll_counter;
static void ltpc_poll(struct timer_list *unused)
{
del_timer(&ltpc_timer);
if(debug & DEBUG_VERBOSE) {
if (!ltpc_poll_counter) {
ltpc_poll_counter = 50;
printk("ltpc poll is alive\n");
}
ltpc_poll_counter--;
}
/* poll 20 times per second */
idle(ltpc_timer_dev);
ltpc_timer.expires = jiffies + HZ/20;
add_timer(&ltpc_timer);
}
/* DDP to LLAP translation */
static netdev_tx_t ltpc_xmit(struct sk_buff *skb, struct net_device *dev)
{
/* in kernel 1.3.xx, on entry skb->data points to ddp header,
* and skb->len is the length of the ddp data + ddp header
*/
int i;
struct lt_sendlap cbuf;
unsigned char *hdr;
cbuf.command = LT_SENDLAP;
cbuf.dnode = skb->data[0];
cbuf.laptype = skb->data[2];
skb_pull(skb,3); /* skip past LLAP header */
cbuf.length = skb->len; /* this is host order */
skb_reset_transport_header(skb);
if(debug & DEBUG_UPPER) {
printk("command ");
for(i=0;i<6;i++)
printk("%02x ",((unsigned char *)&cbuf)[i]);
printk("\n");
}
hdr = skb_transport_header(skb);
do_write(dev, &cbuf, sizeof(cbuf), hdr, skb->len);
if(debug & DEBUG_UPPER) {
printk("sent %d ddp bytes\n",skb->len);
for (i = 0; i < skb->len; i++)
printk("%02x ", hdr[i]);
printk("\n");
}
dev->stats.tx_packets++;
dev->stats.tx_bytes += skb->len;
dev_kfree_skb(skb);
return NETDEV_TX_OK;
}
/* initialization stuff */
static int __init ltpc_probe_dma(int base, int dma)
{
int want = (dma == 3) ? 2 : (dma == 1) ? 1 : 3;
unsigned long timeout;
unsigned long f;
if (want & 1) {
if (request_dma(1,"ltpc")) {
want &= ~1;
} else {
f=claim_dma_lock();
disable_dma(1);
clear_dma_ff(1);
set_dma_mode(1,DMA_MODE_WRITE);
set_dma_addr(1,virt_to_bus(ltdmabuf));
set_dma_count(1,sizeof(struct lt_mem));
enable_dma(1);
release_dma_lock(f);
}
}
if (want & 2) {
if (request_dma(3,"ltpc")) {
want &= ~2;
} else {
f=claim_dma_lock();
disable_dma(3);
clear_dma_ff(3);
set_dma_mode(3,DMA_MODE_WRITE);
set_dma_addr(3,virt_to_bus(ltdmabuf));
set_dma_count(3,sizeof(struct lt_mem));
enable_dma(3);
release_dma_lock(f);
}
}
/* set up request */
/* FIXME -- do timings better! */
ltdmabuf[0] = LT_READMEM;
ltdmabuf[1] = 1; /* mailbox */
ltdmabuf[2] = 0; ltdmabuf[3] = 0; /* address */
ltdmabuf[4] = 0; ltdmabuf[5] = 1; /* read 0x0100 bytes */
ltdmabuf[6] = 0; /* dunno if this is necessary */
inb_p(io+1);
inb_p(io+0);
timeout = jiffies+100*HZ/100;
while(time_before(jiffies, timeout)) {
if ( 0xfa == inb_p(io+6) ) break;
}
inb_p(io+3);
inb_p(io+2);
while(time_before(jiffies, timeout)) {
if ( 0xfb == inb_p(io+6) ) break;
}
/* release the other dma channel (if we opened both of them) */
if ((want & 2) && (get_dma_residue(3)==sizeof(struct lt_mem))) {
want &= ~2;
free_dma(3);
}
if ((want & 1) && (get_dma_residue(1)==sizeof(struct lt_mem))) {
want &= ~1;
free_dma(1);
}
if (!want)
return 0;
return (want & 2) ? 3 : 1;
}
static const struct net_device_ops ltpc_netdev = {
.ndo_start_xmit = ltpc_xmit,
.ndo_do_ioctl = ltpc_ioctl,
.ndo_set_rx_mode = set_multicast_list,
};
static struct net_device * __init ltpc_probe(void)
{
struct net_device *dev;
int err = -ENOMEM;
int x=0,y=0;
int autoirq;
unsigned long f;
unsigned long timeout;
dev = alloc_ltalkdev(sizeof(struct ltpc_private));
if (!dev)
goto out;
/* probe for the I/O port address */
if (io != 0x240 && request_region(0x220,8,"ltpc")) {
x = inb_p(0x220+6);
if ( (x!=0xff) && (x>=0xf0) ) {
io = 0x220;
goto got_port;
}
release_region(0x220,8);
}
if (io != 0x220 && request_region(0x240,8,"ltpc")) {
y = inb_p(0x240+6);
if ( (y!=0xff) && (y>=0xf0) ){
io = 0x240;
goto got_port;
}
release_region(0x240,8);
}
/* give up in despair */
printk(KERN_ERR "LocalTalk card not found; 220 = %02x, 240 = %02x.\n", x,y);
err = -ENODEV;
goto out1;
got_port:
/* probe for the IRQ line */
if (irq < 2) {
unsigned long irq_mask;
irq_mask = probe_irq_on();
/* reset the interrupt line */
inb_p(io+7);
inb_p(io+7);
/* trigger an interrupt (I hope) */
inb_p(io+6);
mdelay(2);
autoirq = probe_irq_off(irq_mask);
if (autoirq == 0) {
printk(KERN_ERR "ltpc: probe at %#x failed to detect IRQ line.\n", io);
} else {
irq = autoirq;
}
}
/* allocate a DMA buffer */
ltdmabuf = (unsigned char *) dma_mem_alloc(1000);
if (!ltdmabuf) {
printk(KERN_ERR "ltpc: mem alloc failed\n");
err = -ENOMEM;
goto out2;
}
ltdmacbuf = &ltdmabuf[800];
if(debug & DEBUG_VERBOSE) {
printk("ltdmabuf pointer %08lx\n",(unsigned long) ltdmabuf);
}
/* reset the card */
inb_p(io+1);
inb_p(io+3);
msleep(20);
inb_p(io+0);
inb_p(io+2);
inb_p(io+7); /* clear reset */
inb_p(io+4);
inb_p(io+5);
inb_p(io+5); /* enable dma */
inb_p(io+6); /* tri-state interrupt line */
ssleep(1);
/* now, figure out which dma channel we're using, unless it's
already been specified */
/* well, 0 is a legal DMA channel, but the LTPC card doesn't
use it... */
dma = ltpc_probe_dma(io, dma);
if (!dma) { /* no dma channel */
printk(KERN_ERR "No DMA channel found on ltpc card.\n");
err = -ENODEV;
goto out3;
}
/* print out friendly message */
if(irq)
printk(KERN_INFO "Apple/Farallon LocalTalk-PC card at %03x, IR%d, DMA%d.\n",io,irq,dma);
else
printk(KERN_INFO "Apple/Farallon LocalTalk-PC card at %03x, DMA%d. Using polled mode.\n",io,dma);
dev->netdev_ops = &ltpc_netdev;
dev->base_addr = io;
dev->irq = irq;
dev->dma = dma;
/* the card will want to send a result at this point */
/* (I think... leaving out this part makes the kernel crash,
so I put it back in...) */
f=claim_dma_lock();
disable_dma(dma);
clear_dma_ff(dma);
set_dma_mode(dma,DMA_MODE_READ);
set_dma_addr(dma,virt_to_bus(ltdmabuf));
set_dma_count(dma,0x100);
enable_dma(dma);
release_dma_lock(f);
(void) inb_p(io+3);
(void) inb_p(io+2);
timeout = jiffies+100*HZ/100;
while(time_before(jiffies, timeout)) {
if( 0xf9 == inb_p(io+6))
break;
schedule();
}
if(debug & DEBUG_VERBOSE) {
printk("setting up timer and irq\n");
}
/* grab it and don't let go :-) */
if (irq && request_irq( irq, ltpc_interrupt, 0, "ltpc", dev) >= 0)
{
(void) inb_p(io+7); /* enable interrupts from board */
(void) inb_p(io+7); /* and reset irq line */
} else {
if( irq )
printk(KERN_ERR "ltpc: IRQ already in use, using polled mode.\n");
dev->irq = 0;
/* polled mode -- 20 times per second */
/* this is really, really slow... should it poll more often? */
ltpc_timer_dev = dev;
timer_setup(&ltpc_timer, ltpc_poll, 0);
ltpc_timer.expires = jiffies + HZ/20;
add_timer(&ltpc_timer);
}
err = register_netdev(dev);
if (err)
goto out4;
return NULL;
out4:
del_timer_sync(&ltpc_timer);
if (dev->irq)
free_irq(dev->irq, dev);
out3:
free_pages((unsigned long)ltdmabuf, get_order(1000));
out2:
release_region(io, 8);
out1:
free_netdev(dev);
out:
return ERR_PTR(err);
}
#ifndef MODULE
/* handles "ltpc=io,irq,dma" kernel command lines */
static int __init ltpc_setup(char *str)
{
int ints[5];
str = get_options(str, ARRAY_SIZE(ints), ints);
if (ints[0] == 0) {
if (str && !strncmp(str, "auto", 4)) {
/* do nothing :-) */
}
else {
/* usage message */
printk (KERN_ERR
"ltpc: usage: ltpc=auto|iobase[,irq[,dma]]\n");
return 0;
}
} else {
io = ints[1];
if (ints[0] > 1) {
irq = ints[2];
}
if (ints[0] > 2) {
dma = ints[3];
}
/* ignore any other parameters */
}
return 1;
}
__setup("ltpc=", ltpc_setup);
#endif
static struct net_device *dev_ltpc;
MODULE_LICENSE("GPL");
module_param(debug, int, 0);
module_param_hw(io, int, ioport, 0);
module_param_hw(irq, int, irq, 0);
module_param_hw(dma, int, dma, 0);
static int __init ltpc_module_init(void)
{
if(io == 0)
printk(KERN_NOTICE
"ltpc: Autoprobing is not recommended for modules\n");
dev_ltpc = ltpc_probe();
return PTR_ERR_OR_ZERO(dev_ltpc);
}
module_init(ltpc_module_init);
static void __exit ltpc_cleanup(void)
{
if(debug & DEBUG_VERBOSE) printk("unregister_netdev\n");
unregister_netdev(dev_ltpc);
del_timer_sync(&ltpc_timer);
if(debug & DEBUG_VERBOSE) printk("freeing irq\n");
if (dev_ltpc->irq)
free_irq(dev_ltpc->irq, dev_ltpc);
if(debug & DEBUG_VERBOSE) printk("freeing dma\n");
if (dev_ltpc->dma)
free_dma(dev_ltpc->dma);
if(debug & DEBUG_VERBOSE) printk("freeing ioaddr\n");
if (dev_ltpc->base_addr)
release_region(dev_ltpc->base_addr,8);
free_netdev(dev_ltpc);
if(debug & DEBUG_VERBOSE) printk("free_pages\n");
free_pages( (unsigned long) ltdmabuf, get_order(1000));
if(debug & DEBUG_VERBOSE) printk("returning from cleanup_module\n");
}
module_exit(ltpc_cleanup);
/* SPDX-License-Identifier: GPL-2.0 */
/*** ltpc.h
*
*
***/
#define LT_GETRESULT 0x00
#define LT_WRITEMEM 0x01
#define LT_READMEM 0x02
#define LT_GETFLAGS 0x04
#define LT_SETFLAGS 0x05
#define LT_INIT 0x10
#define LT_SENDLAP 0x13
#define LT_RCVLAP 0x14
/* the flag that we care about */
#define LT_FLAG_ALLLAP 0x04
struct lt_getresult {
unsigned char command;
unsigned char mailbox;
};
struct lt_mem {
unsigned char command;
unsigned char mailbox;
unsigned short addr; /* host order */
unsigned short length; /* host order */
};
struct lt_setflags {
unsigned char command;
unsigned char mailbox;
unsigned char flags;
};
struct lt_getflags {
unsigned char command;
unsigned char mailbox;
};
struct lt_init {
unsigned char command;
unsigned char mailbox;
unsigned char hint;
};
struct lt_sendlap {
unsigned char command;
unsigned char mailbox;
unsigned char dnode;
unsigned char laptype;
unsigned short length; /* host order */
};
struct lt_rcvlap {
unsigned char command;
unsigned char dnode;
unsigned char snode;
unsigned char laptype;
unsigned short length; /* host order */
};
union lt_command {
struct lt_getresult getresult;
struct lt_mem mem;
struct lt_setflags setflags;
struct lt_getflags getflags;
struct lt_init init;
struct lt_sendlap sendlap;
struct lt_rcvlap rcvlap;
};
typedef union lt_command lt_command;
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment