Merge tag 'tty-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull serial driver fixes from Greg KH:
 "Here are some small serial driver fixes for 6.7-rc4 to resolve some
  reported issues. Included in here are:

   - pl011 dma support fix

   - sc16is7xx driver fix

   - ma35d1 console index fix

   - 8250 driver fixes for small issues

  All of these have been in linux-next with no reported issues"

* tag 'tty-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_dw: Add ACPI ID for Granite Rapids-D UART
  serial: ma35d1: Validate console index before assignment
  ARM: PL011: Fix DMA support
  serial: sc16is7xx: address RX timeout interrupt errata
  serial: 8250: 8250_omap: Clear UART_HAS_RHR_IT_DIS bit
  serial: 8250_omap: Add earlycon support for the AM654 UART controller
  serial: 8250: 8250_omap: Do not start RX DMA on THRI interrupt

drivers/tty/serial/8250/8250_dw.c

@@ -777,6 +777,7 @@ static const struct acpi_device_id dw8250_acpi_match[] = {
 	{ "INT33C5", (kernel_ulong_t)&dw8250_dw_apb },
 	{ "INT3434", (kernel_ulong_t)&dw8250_dw_apb },
 	{ "INT3435", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "INTC10EE", (kernel_ulong_t)&dw8250_dw_apb },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);

drivers/tty/serial/8250/8250_early.c

@@ -189,5 +189,6 @@ static int __init early_omap8250_setup(struct earlycon_device *device,
 OF_EARLYCON_DECLARE(omap8250, "ti,omap2-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap3-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap4-uart", early_omap8250_setup);
+OF_EARLYCON_DECLARE(omap8250, "ti,am654-uart", early_omap8250_setup);
 
 #endif

drivers/tty/serial/8250/8250_omap.c

@@ -933,7 +933,7 @@ static void __dma_rx_do_complete(struct uart_8250_port *p)
 	if (priv->habit & UART_HAS_RHR_IT_DIS) {
 		reg = serial_in(p, UART_OMAP_IER2);
 		reg &= ~UART_OMAP_IER2_RHR_IT_DIS;
-		serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS);
+		serial_out(p, UART_OMAP_IER2, reg);
 	}
 
 	dmaengine_tx_status(rxchan, cookie, &state);
@@ -1079,7 +1079,7 @@ static int omap_8250_rx_dma(struct uart_8250_port *p)
 	if (priv->habit & UART_HAS_RHR_IT_DIS) {
 		reg = serial_in(p, UART_OMAP_IER2);
 		reg |= UART_OMAP_IER2_RHR_IT_DIS;
-		serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS);
+		serial_out(p, UART_OMAP_IER2, reg);
 	}
 
 	dma_async_issue_pending(dma->rxchan);
@@ -1298,10 +1298,12 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
 
 	status = serial_port_in(port, UART_LSR);
 
+	if ((iir & 0x3f) != UART_IIR_THRI) {
 		if (priv->habit & UART_HAS_EFR2)
 			am654_8250_handle_rx_dma(up, iir, status);
 		else
 			status = omap_8250_handle_rx_dma(up, iir, status);
+	}
 
 	serial8250_modem_status(up);
 	if (status & UART_LSR_THRE && up->dma->tx_err) {

drivers/tty/serial/ma35d1_serial.c

@@ -552,11 +552,19 @@ static void ma35d1serial_console_putchar(struct uart_port *port, unsigned char c
  */
 static void ma35d1serial_console_write(struct console *co, const char *s, u32 count)
 {
-	struct uart_ma35d1_port *up = &ma35d1serial_ports[co->index];
+	struct uart_ma35d1_port *up;
 	unsigned long flags;
 	int locked = 1;
 	u32 ier;
 
+	if ((co->index < 0) || (co->index >= MA35_UART_NR)) {
+		pr_warn("Failed to write on ononsole port %x, out of range\n",
+			co->index);
+		return;
+	}
+
+	up = &ma35d1serial_ports[co->index];
+
 	if (up->port.sysrq)
 		locked = 0;
 	else if (oops_in_progress)

drivers/tty/serial/sc16is7xx.c

@@ -766,6 +766,18 @@ static bool sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
 		case SC16IS7XX_IIR_RTOI_SRC:
 		case SC16IS7XX_IIR_XOFFI_SRC:
 			rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG);
+
+			/*
+			 * There is a silicon bug that makes the chip report a
+			 * time-out interrupt but no data in the FIFO. This is
+			 * described in errata section 18.1.4.
+			 *
+			 * When this happens, read one byte from the FIFO to
+			 * clear the interrupt.
+			 */
+			if (iir == SC16IS7XX_IIR_RTOI_SRC && !rxlen)
+				rxlen = 1;
+
 			if (rxlen)
 				sc16is7xx_handle_rx(port, rxlen, iir);
 			break;