Commit 0e948042 authored by Bjorn Andersson's avatar Bjorn Andersson Committed by Linus Walleij

pinctrl: qcom: spmi-mpp: Implement support for sink mode

The MPP supports three modes; digital, analog and sink mode. This patch
implements support for the latter.
Signed-off-by: default avatarBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent eaaf5dd4
...@@ -134,6 +134,11 @@ to specify in a pin configuration subnode: ...@@ -134,6 +134,11 @@ to specify in a pin configuration subnode:
and/or output-high, output-low MPP could operate as and/or output-high, output-low MPP could operate as
Bidirectional Logic, Analog Input, Analog Output. Bidirectional Logic, Analog Input, Analog Output.
- qcom,sink-mode:
Usage: optional
Value type: <u32> or <none>
Definition: Selects sink mode of operation
- qcom,amux-route: - qcom,amux-route:
Usage: optional Usage: optional
Value type: <u32> Value type: <u32>
......
...@@ -62,6 +62,7 @@ ...@@ -62,6 +62,7 @@
#define PMIC_MPP_REG_DIG_IN_CTL 0x43 #define PMIC_MPP_REG_DIG_IN_CTL 0x43
#define PMIC_MPP_REG_EN_CTL 0x46 #define PMIC_MPP_REG_EN_CTL 0x46
#define PMIC_MPP_REG_AIN_CTL 0x4a #define PMIC_MPP_REG_AIN_CTL 0x4a
#define PMIC_MPP_REG_SINK_CTL 0x4c
/* PMIC_MPP_REG_MODE_CTL */ /* PMIC_MPP_REG_MODE_CTL */
#define PMIC_MPP_REG_MODE_VALUE_MASK 0x1 #define PMIC_MPP_REG_MODE_VALUE_MASK 0x1
...@@ -98,6 +99,7 @@ ...@@ -98,6 +99,7 @@
/* Qualcomm specific pin configurations */ /* Qualcomm specific pin configurations */
#define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1) #define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1)
#define PMIC_MPP_CONF_ANALOG_MODE (PIN_CONFIG_END + 2) #define PMIC_MPP_CONF_ANALOG_MODE (PIN_CONFIG_END + 2)
#define PMIC_MPP_CONF_SINK_MODE (PIN_CONFIG_END + 3)
/** /**
* struct pmic_mpp_pad - keep current MPP settings * struct pmic_mpp_pad - keep current MPP settings
...@@ -109,11 +111,13 @@ ...@@ -109,11 +111,13 @@
* @input_enabled: Set to true if MPP input buffer logic is enabled. * @input_enabled: Set to true if MPP input buffer logic is enabled.
* @analog_mode: Set to true when MPP should operate in Analog Input, Analog * @analog_mode: Set to true when MPP should operate in Analog Input, Analog
* Output or Bidirectional Analog mode. * Output or Bidirectional Analog mode.
* @sink_mode: Boolean indicating if ink mode is slected
* @num_sources: Number of power-sources supported by this MPP. * @num_sources: Number of power-sources supported by this MPP.
* @power_source: Current power-source used. * @power_source: Current power-source used.
* @amux_input: Set the source for analog input. * @amux_input: Set the source for analog input.
* @pullup: Pullup resistor value. Valid in Bidirectional mode only. * @pullup: Pullup resistor value. Valid in Bidirectional mode only.
* @function: See pmic_mpp_functions[]. * @function: See pmic_mpp_functions[].
* @drive_strength: Amount of current in sink mode
*/ */
struct pmic_mpp_pad { struct pmic_mpp_pad {
u16 base; u16 base;
...@@ -123,11 +127,13 @@ struct pmic_mpp_pad { ...@@ -123,11 +127,13 @@ struct pmic_mpp_pad {
bool output_enabled; bool output_enabled;
bool input_enabled; bool input_enabled;
bool analog_mode; bool analog_mode;
bool sink_mode;
unsigned int num_sources; unsigned int num_sources;
unsigned int power_source; unsigned int power_source;
unsigned int amux_input; unsigned int amux_input;
unsigned int pullup; unsigned int pullup;
unsigned int function; unsigned int function;
unsigned int drive_strength;
}; };
struct pmic_mpp_state { struct pmic_mpp_state {
...@@ -140,12 +146,14 @@ struct pmic_mpp_state { ...@@ -140,12 +146,14 @@ struct pmic_mpp_state {
static const struct pinconf_generic_params pmic_mpp_bindings[] = { static const struct pinconf_generic_params pmic_mpp_bindings[] = {
{"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE, 0}, {"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE, 0},
{"qcom,analog-mode", PMIC_MPP_CONF_ANALOG_MODE, 0}, {"qcom,analog-mode", PMIC_MPP_CONF_ANALOG_MODE, 0},
{"qcom,sink-mode", PMIC_MPP_CONF_SINK_MODE, 0},
}; };
#ifdef CONFIG_DEBUG_FS #ifdef CONFIG_DEBUG_FS
static const struct pin_config_item pmic_conf_items[] = { static const struct pin_config_item pmic_conf_items[] = {
PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true), PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true),
PCONFDUMP(PMIC_MPP_CONF_ANALOG_MODE, "analog output", NULL, false), PCONFDUMP(PMIC_MPP_CONF_ANALOG_MODE, "analog output", NULL, false),
PCONFDUMP(PMIC_MPP_CONF_SINK_MODE, "sink mode", NULL, false),
}; };
#endif #endif
...@@ -243,33 +251,28 @@ static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev, ...@@ -243,33 +251,28 @@ static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev,
return 0; return 0;
} }
static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function, static int pmic_mpp_write_mode_ctl(struct pmic_mpp_state *state,
unsigned pin) struct pmic_mpp_pad *pad)
{ {
struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
struct pmic_mpp_pad *pad;
unsigned int val; unsigned int val;
int ret;
pad = pctldev->desc->pins[pin].drv_data;
pad->function = function; if (pad->analog_mode) {
val = PMIC_MPP_MODE_ANALOG_INPUT;
if (!pad->analog_mode) {
val = PMIC_MPP_MODE_DIGITAL_INPUT;
if (pad->output_enabled) { if (pad->output_enabled) {
if (pad->input_enabled) if (pad->input_enabled)
val = PMIC_MPP_MODE_DIGITAL_BIDIR; val = PMIC_MPP_MODE_ANALOG_BIDIR;
else else
val = PMIC_MPP_MODE_DIGITAL_OUTPUT; val = PMIC_MPP_MODE_ANALOG_OUTPUT;
} }
} else if (pad->sink_mode) {
val = PMIC_MPP_MODE_CURRENT_SINK;
} else { } else {
val = PMIC_MPP_MODE_ANALOG_INPUT; val = PMIC_MPP_MODE_DIGITAL_INPUT;
if (pad->output_enabled) { if (pad->output_enabled) {
if (pad->input_enabled) if (pad->input_enabled)
val = PMIC_MPP_MODE_ANALOG_BIDIR; val = PMIC_MPP_MODE_DIGITAL_BIDIR;
else else
val = PMIC_MPP_MODE_ANALOG_OUTPUT; val = PMIC_MPP_MODE_DIGITAL_OUTPUT;
} }
} }
...@@ -277,9 +280,22 @@ static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function, ...@@ -277,9 +280,22 @@ static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT; val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK; val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK;
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val); return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
if (ret < 0) }
return ret;
static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
unsigned pin)
{
struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
struct pmic_mpp_pad *pad;
unsigned int val;
int ret;
pad = pctldev->desc->pins[pin].drv_data;
pad->function = function;
ret = pmic_mpp_write_mode_ctl(state, pad);
val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT; val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
...@@ -339,9 +355,15 @@ static int pmic_mpp_config_get(struct pinctrl_dev *pctldev, ...@@ -339,9 +355,15 @@ static int pmic_mpp_config_get(struct pinctrl_dev *pctldev,
case PMIC_MPP_CONF_AMUX_ROUTE: case PMIC_MPP_CONF_AMUX_ROUTE:
arg = pad->amux_input; arg = pad->amux_input;
break; break;
case PIN_CONFIG_DRIVE_STRENGTH:
arg = pad->drive_strength;
break;
case PMIC_MPP_CONF_ANALOG_MODE: case PMIC_MPP_CONF_ANALOG_MODE:
arg = pad->analog_mode; arg = pad->analog_mode;
break; break;
case PMIC_MPP_CONF_SINK_MODE:
arg = pad->sink_mode;
break;
default: default:
return -EINVAL; return -EINVAL;
} }
...@@ -403,13 +425,19 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin, ...@@ -403,13 +425,19 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
pad->output_enabled = true; pad->output_enabled = true;
pad->out_value = arg; pad->out_value = arg;
break; break;
case PIN_CONFIG_DRIVE_STRENGTH:
arg = pad->drive_strength;
break;
case PMIC_MPP_CONF_AMUX_ROUTE: case PMIC_MPP_CONF_AMUX_ROUTE:
if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4) if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4)
return -EINVAL; return -EINVAL;
pad->amux_input = arg; pad->amux_input = arg;
break; break;
case PMIC_MPP_CONF_ANALOG_MODE: case PMIC_MPP_CONF_ANALOG_MODE:
pad->analog_mode = true; pad->analog_mode = !!arg;
break;
case PMIC_MPP_CONF_SINK_MODE:
pad->sink_mode = !!arg;
break; break;
default: default:
return -EINVAL; return -EINVAL;
...@@ -434,29 +462,7 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin, ...@@ -434,29 +462,7 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
if (ret < 0) if (ret < 0)
return ret; return ret;
if (!pad->analog_mode) { ret = pmic_mpp_write_mode_ctl(state, pad);
val = 0; /* just digital input */
if (pad->output_enabled) {
if (pad->input_enabled)
val = 2; /* digital input and output */
else
val = 1; /* just digital output */
}
} else {
val = 4; /* just analog input */
if (pad->output_enabled) {
if (pad->input_enabled)
val = 3; /* analog input and output */
else
val = 5; /* just analog output */
}
}
val = val << PMIC_MPP_REG_MODE_DIR_SHIFT;
val |= pad->function << PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
val |= pad->out_value & PMIC_MPP_REG_MODE_VALUE_MASK;
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
if (ret < 0) if (ret < 0)
return ret; return ret;
...@@ -476,6 +482,9 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev, ...@@ -476,6 +482,9 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
"0.6kOhm", "10kOhm", "30kOhm", "Disabled" "0.6kOhm", "10kOhm", "30kOhm", "Disabled"
}; };
static const char *const modes[] = {
"digital", "analog", "sink"
};
pad = pctldev->desc->pins[pin].drv_data; pad = pctldev->desc->pins[pin].drv_data;
...@@ -495,7 +504,7 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev, ...@@ -495,7 +504,7 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
} }
seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in"); seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
seq_printf(s, " %-4s", pad->analog_mode ? "ana" : "dig"); seq_printf(s, " %-7s", modes[pad->analog_mode ? 1 : (pad->sink_mode ? 2 : 0)]);
seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]); seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]);
seq_printf(s, " vin-%d", pad->power_source); seq_printf(s, " vin-%d", pad->power_source);
seq_printf(s, " %-8s", biases[pad->pullup]); seq_printf(s, " %-8s", biases[pad->pullup]);
...@@ -666,31 +675,43 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state, ...@@ -666,31 +675,43 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state,
pad->input_enabled = true; pad->input_enabled = true;
pad->output_enabled = false; pad->output_enabled = false;
pad->analog_mode = false; pad->analog_mode = false;
pad->sink_mode = false;
break; break;
case PMIC_MPP_MODE_DIGITAL_OUTPUT: case PMIC_MPP_MODE_DIGITAL_OUTPUT:
pad->input_enabled = false; pad->input_enabled = false;
pad->output_enabled = true; pad->output_enabled = true;
pad->analog_mode = false; pad->analog_mode = false;
pad->sink_mode = false;
break; break;
case PMIC_MPP_MODE_DIGITAL_BIDIR: case PMIC_MPP_MODE_DIGITAL_BIDIR:
pad->input_enabled = true; pad->input_enabled = true;
pad->output_enabled = true; pad->output_enabled = true;
pad->analog_mode = false; pad->analog_mode = false;
pad->sink_mode = false;
break; break;
case PMIC_MPP_MODE_ANALOG_BIDIR: case PMIC_MPP_MODE_ANALOG_BIDIR:
pad->input_enabled = true; pad->input_enabled = true;
pad->output_enabled = true; pad->output_enabled = true;
pad->analog_mode = true; pad->analog_mode = true;
pad->sink_mode = false;
break; break;
case PMIC_MPP_MODE_ANALOG_INPUT: case PMIC_MPP_MODE_ANALOG_INPUT:
pad->input_enabled = true; pad->input_enabled = true;
pad->output_enabled = false; pad->output_enabled = false;
pad->analog_mode = true; pad->analog_mode = true;
pad->sink_mode = false;
break; break;
case PMIC_MPP_MODE_ANALOG_OUTPUT: case PMIC_MPP_MODE_ANALOG_OUTPUT:
pad->input_enabled = false; pad->input_enabled = false;
pad->output_enabled = true; pad->output_enabled = true;
pad->analog_mode = true; pad->analog_mode = true;
pad->sink_mode = false;
break;
case PMIC_MPP_MODE_CURRENT_SINK:
pad->input_enabled = false;
pad->output_enabled = true;
pad->analog_mode = false;
pad->sink_mode = true;
break; break;
default: default:
dev_err(state->dev, "unknown MPP direction\n"); dev_err(state->dev, "unknown MPP direction\n");
...@@ -721,6 +742,12 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state, ...@@ -721,6 +742,12 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state,
pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT; pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT;
pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK; pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK;
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_SINK_CTL);
if (val < 0)
return val;
pad->drive_strength = val;
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL); val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
if (val < 0) if (val < 0)
return val; return val;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment