Commit 19093313 authored by Mauro Carvalho Chehab's avatar Mauro Carvalho Chehab Committed by David S. Miller

docs: networking: convert ipv6.txt to ReST

Not much to be done here:

- add SPDX header;
- add a document title;
- mark a literal as such, in order to avoid a warning;
- add to networking/index.rst.
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 1cec2cac
...@@ -356,7 +356,7 @@ ...@@ -356,7 +356,7 @@
shot down by NMI shot down by NMI
autoconf= [IPV6] autoconf= [IPV6]
See Documentation/networking/ipv6.txt. See Documentation/networking/ipv6.rst.
show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller
Limit apic dumping. The parameter defines the maximal Limit apic dumping. The parameter defines the maximal
...@@ -872,7 +872,7 @@ ...@@ -872,7 +872,7 @@
miss to occur. miss to occur.
disable= [IPV6] disable= [IPV6]
See Documentation/networking/ipv6.txt. See Documentation/networking/ipv6.rst.
hardened_usercopy= hardened_usercopy=
[KNL] Under CONFIG_HARDENED_USERCOPY, whether [KNL] Under CONFIG_HARDENED_USERCOPY, whether
...@@ -912,7 +912,7 @@ ...@@ -912,7 +912,7 @@
to workaround buggy firmware. to workaround buggy firmware.
disable_ipv6= [IPV6] disable_ipv6= [IPV6]
See Documentation/networking/ipv6.txt. See Documentation/networking/ipv6.rst.
disable_mtrr_cleanup [X86] disable_mtrr_cleanup [X86]
The kernel tries to adjust MTRR layout from continuous The kernel tries to adjust MTRR layout from continuous
......
...@@ -70,6 +70,7 @@ Contents: ...@@ -70,6 +70,7 @@ Contents:
iphase iphase
ipsec ipsec
ip-sysctl ip-sysctl
ipv6
.. only:: subproject and html .. only:: subproject and html
......
.. SPDX-License-Identifier: GPL-2.0
====
IPv6
====
Options for the ipv6 module are supplied as parameters at load time. Options for the ipv6 module are supplied as parameters at load time.
Module options may be given as command line arguments to the insmod Module options may be given as command line arguments to the insmod
or modprobe command, but are usually specified in either or modprobe command, but are usually specified in either
/etc/modules.d/*.conf configuration files, or in a distro-specific ``/etc/modules.d/*.conf`` configuration files, or in a distro-specific
configuration file. configuration file.
The available ipv6 module parameters are listed below. If a parameter The available ipv6 module parameters are listed below. If a parameter
......
...@@ -13,7 +13,7 @@ menuconfig IPV6 ...@@ -13,7 +13,7 @@ menuconfig IPV6
For general information about IPv6, see For general information about IPv6, see
<https://en.wikipedia.org/wiki/IPv6>. <https://en.wikipedia.org/wiki/IPv6>.
For specific information about IPv6 under Linux, see For specific information about IPv6 under Linux, see
Documentation/networking/ipv6.txt and read the HOWTO at Documentation/networking/ipv6.rst and read the HOWTO at
<http://www.tldp.org/HOWTO/Linux+IPv6-HOWTO/> <http://www.tldp.org/HOWTO/Linux+IPv6-HOWTO/>
To compile this protocol support as a module, choose M here: the To compile this protocol support as a module, choose M here: the
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment