Commit 229e6b6e authored by Huang, Xiong's avatar Huang, Xiong Committed by David S. Miller

atl1c: refine mac address related code

On some platform with EEPROM/OTP existing, the BIOS could overwrite
a new MAC address for the NIC. so, the permanent mac address should
be from BIOS. the address is restored when driver removing.
Voltage raising isn't applicable for l1d.
Replace swab32 with htonl for big/little endian platform.
related Registers are refined as well.
Signed-off-by: default avatarxiong <xiong@qca.qualcomm.com>
Tested-by: default avatarLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e1192580
......@@ -43,7 +43,7 @@ int atl1c_check_eeprom_exist(struct atl1c_hw *hw)
return 0;
}
void atl1c_hw_set_mac_addr(struct atl1c_hw *hw)
void atl1c_hw_set_mac_addr(struct atl1c_hw *hw, u8 *mac_addr)
{
u32 value;
/*
......@@ -51,33 +51,48 @@ void atl1c_hw_set_mac_addr(struct atl1c_hw *hw)
* 0: 6AF600DC 1: 000B
* low dword
*/
value = (((u32)hw->mac_addr[2]) << 24) |
(((u32)hw->mac_addr[3]) << 16) |
(((u32)hw->mac_addr[4]) << 8) |
(((u32)hw->mac_addr[5])) ;
value = mac_addr[2] << 24 |
mac_addr[3] << 16 |
mac_addr[4] << 8 |
mac_addr[5];
AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 0, value);
/* hight dword */
value = (((u32)hw->mac_addr[0]) << 8) |
(((u32)hw->mac_addr[1])) ;
value = mac_addr[0] << 8 |
mac_addr[1];
AT_WRITE_REG_ARRAY(hw, REG_MAC_STA_ADDR, 1, value);
}
/* read mac address from hardware register */
static bool atl1c_read_current_addr(struct atl1c_hw *hw, u8 *eth_addr)
{
u32 addr[2];
AT_READ_REG(hw, REG_MAC_STA_ADDR, &addr[0]);
AT_READ_REG(hw, REG_MAC_STA_ADDR + 4, &addr[1]);
*(u32 *) &eth_addr[2] = htonl(addr[0]);
*(u16 *) &eth_addr[0] = htons((u16)addr[1]);
return is_valid_ether_addr(eth_addr);
}
/*
* atl1c_get_permanent_address
* return 0 if get valid mac address,
*/
static int atl1c_get_permanent_address(struct atl1c_hw *hw)
{
u32 addr[2];
u32 i;
u32 otp_ctrl_data;
u32 twsi_ctrl_data;
u8 eth_addr[ETH_ALEN];
u16 phy_data;
bool raise_vol = false;
/* MAC-address from BIOS is the 1st priority */
if (atl1c_read_current_addr(hw, hw->perm_mac_addr))
return 0;
/* init */
addr[0] = addr[1] = 0;
AT_READ_REG(hw, REG_OTP_CTRL, &otp_ctrl_data);
if (atl1c_check_eeprom_exist(hw)) {
if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c) {
......@@ -89,21 +104,14 @@ static int atl1c_get_permanent_address(struct atl1c_hw *hw)
msleep(1);
}
}
if (hw->nic_type == athr_l2c_b ||
hw->nic_type == athr_l2c_b2 ||
hw->nic_type == athr_l1d) {
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x00);
if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &phy_data))
goto out;
phy_data &= 0xFF7F;
atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data);
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x3B);
if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &phy_data))
goto out;
phy_data |= 0x8;
atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data);
/* raise voltage temporally for l2cb */
if (hw->nic_type == athr_l2c_b || hw->nic_type == athr_l2c_b2) {
atl1c_read_phy_dbg(hw, MIIDBG_ANACTRL, &phy_data);
phy_data &= ~ANACTRL_HB_EN;
atl1c_write_phy_dbg(hw, MIIDBG_ANACTRL, phy_data);
atl1c_read_phy_dbg(hw, MIIDBG_VOLT_CTRL, &phy_data);
phy_data |= VOLT_CTRL_SWLOWEST;
atl1c_write_phy_dbg(hw, MIIDBG_VOLT_CTRL, phy_data);
udelay(20);
raise_vol = true;
}
......@@ -127,37 +135,18 @@ static int atl1c_get_permanent_address(struct atl1c_hw *hw)
msleep(1);
}
if (raise_vol) {
if (hw->nic_type == athr_l2c_b ||
hw->nic_type == athr_l2c_b2 ||
hw->nic_type == athr_l1d ||
hw->nic_type == athr_l1d_2) {
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x00);
if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &phy_data))
goto out;
phy_data |= 0x80;
atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data);
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x3B);
if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &phy_data))
goto out;
phy_data &= 0xFFF7;
atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data);
atl1c_read_phy_dbg(hw, MIIDBG_ANACTRL, &phy_data);
phy_data |= ANACTRL_HB_EN;
atl1c_write_phy_dbg(hw, MIIDBG_ANACTRL, phy_data);
atl1c_read_phy_dbg(hw, MIIDBG_VOLT_CTRL, &phy_data);
phy_data &= ~VOLT_CTRL_SWLOWEST;
atl1c_write_phy_dbg(hw, MIIDBG_VOLT_CTRL, phy_data);
udelay(20);
}
}
/* maybe MAC-address is from BIOS */
AT_READ_REG(hw, REG_MAC_STA_ADDR, &addr[0]);
AT_READ_REG(hw, REG_MAC_STA_ADDR + 4, &addr[1]);
*(u32 *) &eth_addr[2] = swab32(addr[0]);
*(u16 *) &eth_addr[0] = swab16(*(u16 *)&addr[1]);
if (is_valid_ether_addr(eth_addr)) {
memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
if (atl1c_read_current_addr(hw, hw->perm_mac_addr))
return 0;
}
out:
return -1;
}
......
......@@ -36,7 +36,7 @@ struct atl1c_hw;
/* function prototype */
void atl1c_phy_disable(struct atl1c_hw *hw);
void atl1c_hw_set_mac_addr(struct atl1c_hw *hw);
void atl1c_hw_set_mac_addr(struct atl1c_hw *hw, u8 *mac_addr);
int atl1c_phy_reset(struct atl1c_hw *hw);
int atl1c_read_mac_addr(struct atl1c_hw *hw);
int atl1c_get_speed_and_duplex(struct atl1c_hw *hw, u16 *speed, u16 *duplex);
......@@ -94,25 +94,17 @@ void atl1c_post_phy_linkchg(struct atl1c_hw *hw, u16 link_speed);
#define REG_DEV_SERIAL_NUM_EN_SHIFT 1
#define REG_TWSI_CTRL 0x218
#define TWSI_CTLR_FREQ_MASK 0x3UL
#define TWSI_CTRL_FREQ_SHIFT 24
#define TWSI_CTRL_FREQ_100K 0
#define TWSI_CTRL_FREQ_200K 1
#define TWSI_CTRL_FREQ_300K 2
#define TWSI_CTRL_FREQ_400K 3
#define TWSI_CTRL_LD_EXIST BIT(23)
#define TWSI_CTRL_HW_LDSTAT BIT(12) /* 0:finish,1:in progress */
#define TWSI_CTRL_SW_LDSTART BIT(11)
#define TWSI_CTRL_LD_OFFSET_MASK 0xFF
#define TWSI_CTRL_LD_OFFSET_SHIFT 0
#define TWSI_CTRL_LD_SLV_ADDR_MASK 0x7
#define TWSI_CTRL_LD_SLV_ADDR_SHIFT 8
#define TWSI_CTRL_SW_LDSTART 0x800
#define TWSI_CTRL_HW_LDSTART 0x1000
#define TWSI_CTRL_SMB_SLV_ADDR_MASK 0x7F
#define TWSI_CTRL_SMB_SLV_ADDR_SHIFT 15
#define TWSI_CTRL_LD_EXIST 0x400000
#define TWSI_CTRL_READ_FREQ_SEL_MASK 0x3
#define TWSI_CTRL_READ_FREQ_SEL_SHIFT 23
#define TWSI_CTRL_FREQ_SEL_100K 0
#define TWSI_CTRL_FREQ_SEL_200K 1
#define TWSI_CTRL_FREQ_SEL_300K 2
#define TWSI_CTRL_FREQ_SEL_400K 3
#define TWSI_CTRL_SMB_SLV_ADDR
#define TWSI_CTRL_WRITE_FREQ_SEL_MASK 0x3
#define TWSI_CTRL_WRITE_FREQ_SEL_SHIFT 24
#define REG_PCIE_DEV_MISC_CTRL 0x21C
#define PCIE_DEV_MISC_EXT_PIPE 0x2
......@@ -135,7 +127,7 @@ void atl1c_post_phy_linkchg(struct atl1c_hw *hw, u16 link_speed);
#define L2CB1_PCIE_PHYMISC2_CDR_BW 3
#define REG_TWSI_DEBUG 0x1108
#define TWSI_DEBUG_DEV_EXIST 0x20000000
#define TWSI_DEBUG_DEV_EXIST BIT(29)
#define REG_DMA_DBG 0x1114
#define DMA_DBG_VENDOR_MSG BIT(0)
......@@ -151,7 +143,7 @@ void atl1c_post_phy_linkchg(struct atl1c_hw *hw, u16 link_speed);
#define REG_EEPROM_DATA_LO 0x12C4
#define REG_OTP_CTRL 0x12F0
#define OTP_CTRL_CLK_EN 0x0002
#define OTP_CTRL_CLK_EN BIT(1)
#define REG_PM_CTRL 0x12F8
#define PM_CTRL_HOTRST BIT(31)
......
......@@ -463,7 +463,7 @@ static int atl1c_set_mac_addr(struct net_device *netdev, void *p)
memcpy(adapter->hw.mac_addr, addr->sa_data, netdev->addr_len);
netdev->addr_assign_type &= ~NET_ADDR_RANDOM;
atl1c_hw_set_mac_addr(&adapter->hw);
atl1c_hw_set_mac_addr(&adapter->hw, adapter->hw.mac_addr);
return 0;
}
......@@ -2534,7 +2534,7 @@ static int __devinit atl1c_probe(struct pci_dev *pdev,
dev_dbg(&pdev->dev, "mac address : %pM\n",
adapter->hw.mac_addr);
atl1c_hw_set_mac_addr(&adapter->hw);
atl1c_hw_set_mac_addr(&adapter->hw, adapter->hw.mac_addr);
INIT_WORK(&adapter->common_task, atl1c_common_task);
adapter->work_event = 0;
err = register_netdev(netdev);
......@@ -2578,6 +2578,8 @@ static void __devexit atl1c_remove(struct pci_dev *pdev)
struct atl1c_adapter *adapter = netdev_priv(netdev);
unregister_netdev(netdev);
/* restore permanent address */
atl1c_hw_set_mac_addr(&adapter->hw, adapter->hw.perm_mac_addr);
atl1c_phy_disable(&adapter->hw);
iounmap(adapter->hw.hw_addr);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment