arm64: dts: qcom: x1e80100-pmics: Add the missing PMICs

During the initial bringup, all of the peripherals on non-SMB PMICs
were either not used, or were not necessary to accomplish certain
goals. This however, left a hole in the hardware description.

Add the missing ones.

Note that the PM8010 errors out on reads on the CRD (works fine on the
QCP) for reasons unknown, but that shall be ironed out in the future..
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240529-topic-x1e_pmic-v1-2-9de0506179eb@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi

@@ -3,10 +3,477 @@
  * Copyright (c) 2024, Linaro Limited
  */
 
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
 / {
+	thermal-zones {
+		pm8550-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pm8550_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pm8550ve-2-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pm8550ve_2_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pmc8380-3-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pmc8380_3_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pmc8380-4-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pmc8380_4_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pmc8380-5-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pmc8380_5_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pmc8380-6-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pmc8380_6_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pm8550ve-8-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pm8550ve_8_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pm8550ve-9-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pm8550ve_9_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pm8010-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pm8010_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus0 {
+	/* PMK8380 */
+	pmk8550: pmic@0 {
+		compatible = "qcom,pm8550", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmk8550_pon: pon@1300 {
+			compatible = "qcom,pmk8350-pon";
+			reg = <0x1300>, <0x800>;
+			reg-names = "hlos", "pbs";
+
+			pon_pwrkey: pwrkey {
+				compatible = "qcom,pmk8350-pwrkey";
+				interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+				linux,code = <KEY_POWER>;
+			};
+
+			pon_resin: resin {
+				compatible = "qcom,pmk8350-resin";
+				interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+				status = "disabled";
+			};
+		};
+
+		pmk8550_rtc: rtc@6100 {
+			compatible = "qcom,pmk8350-rtc";
+			reg = <0x6100>, <0x6200>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+			/* Not yet sure what blocks access */
+			status = "reserved";
+		};
+
+		pmk8550_sdam_2: nvram@7100 {
+			compatible = "qcom,spmi-sdam";
+			reg = <0x7100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x7100 0x100>;
+
+			reboot_reason: reboot-reason@48 {
+				reg = <0x48 0x1>;
+				bits = <1 7>;
+			};
+		};
+
+		pmk8550_gpios: gpio@8800 {
+			compatible = "qcom,pmk8550-gpio", "qcom,spmi-gpio";
+			reg = <0xb800>;
+			gpio-controller;
+			gpio-ranges = <&pmk8550_gpios 0 0 6>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	/* PMC8380C */
+	pm8550: pmic@1 {
+		compatible = "qcom,pm8550", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8550_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8550_gpios: gpio@8800 {
+			compatible = "qcom,pm8550-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm8550_gpios 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8550_flash: led-controller@ee00 {
+			compatible = "qcom,pm8550-flash-led", "qcom,spmi-flash-led";
+			reg = <0xee00>;
+			status = "disabled";
+		};
+
+		pm8550_pwm: pwm {
+			compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm";
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+	};
+
+	/* PMC8380VE */
+	pm8550ve_2: pmic@2 {
+		compatible = "qcom,pm8550", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8550ve_2_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8550ve_2_gpios: gpio@8800 {
+			compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm8550ve_2_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	/* PMC8380 is actually not a PM8550 series rebrand */
+	pmc8380_3: pmic@3 {
+		compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+		reg = <0x3 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8380_3_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8380_3_gpios: gpio@8800 {
+			compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8380_3_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmc8380_4: pmic@4 {
+		compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8380_4_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8380_4_gpios: gpio@8800 {
+			compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8380_4_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmc8380_5: pmic@5 {
+		compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+		reg = <0x5 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8380_5_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8380_5_gpios: gpio@8800 {
+			compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8380_5_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmc8380_6: pmic@6 {
+		compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+		reg = <0x6 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8380_6_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8380_6_gpios: gpio@8800 {
+			compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8380_6_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	/* PMC8380VE */
+	pm8550ve_8: pmic@8 {
+		compatible = "qcom,pm8550", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8550ve_8_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x8 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8550ve_8_gpios: gpio@8800 {
+			compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm8550ve_8_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	/* PMC8380VE */
+	pm8550ve_9: pmic@9 {
+		compatible = "qcom,pm8550", "qcom,spmi-pmic";
+		reg = <0x9 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8550ve_9_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8550ve_9_gpios: gpio@8800 {
+			compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm8550ve_9_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8010: pmic@c {
+		compatible = "qcom,pm8010", "qcom,spmi-pmic";
+		reg = <0xc SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8010_temp_alarm: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+	};
 };
 
 &spmi_bus1 {
@@ -48,4 +515,17 @@ smb2360_2_eusb2_repeater: phy@fd00 {
 			#phy-cells = <0>;
 		};
 	};
+
+	smb2360_3: pmic@c {
+		compatible = "qcom,smb2360", "qcom,spmi-pmic";
+		reg = <0xc SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		smb2360_3_eusb2_repeater: phy@fd00 {
+			compatible = "qcom,smb2360-eusb2-repeater";
+			reg = <0xfd00>;
+			#phy-cells = <0>;
+		};
+	};
 };