gpio: stmpe: Fix edge and rising/falling edge detection

By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets,
it appears that edge detection and rising/falling edge detection
is not supported by all STMPE variant:

           GPIO              GPIO
      Edge detection     rising/falling
                         edge detection
 610 |      X        |         X       |
 801 |               |                 |
 811 |      X        |         X       |
1600 |               |                 |
1601 |      X        |         X       |
1801 |               |         X       |
2401 |      X        |         X       |
2403 |      X        |         X       |

Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly
take these cases into account.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

drivers/gpio/gpio-stmpe.c

@@ -247,19 +247,44 @@ static void stmpe_dbg_show_one(struct seq_file *s,
 			   gpio, label ?: "(none)",
 			   val ? "hi" : "lo");
 	} else {
-		u8 edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] + num_banks - 1 - (offset / 8);
-		u8 rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] - (offset / 8);
-		u8 fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] - (offset / 8);
-		u8 irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] - (offset / 8);
-		bool edge_det;
-		bool rise;
-		bool fall;
+		u8 edge_det_reg;
+		u8 rise_reg;
+		u8 fall_reg;
+		u8 irqen_reg;
+
+		char *edge_det_values[] = {"edge-inactive",
+					   "edge-asserted",
+					   "not-supported"};
+		char *rise_values[] = {"no-rising-edge-detection",
+				       "rising-edge-detection",
+				       "not-supported"};
+		char *fall_values[] = {"no-falling-edge-detection",
+				       "falling-edge-detection",
+				       "not-supported"};
+		#define NOT_SUPPORTED_IDX 2
+		u8 edge_det = NOT_SUPPORTED_IDX;
+		u8 rise = NOT_SUPPORTED_IDX;
+		u8 fall = NOT_SUPPORTED_IDX;
 		bool irqen;
 
+		switch (stmpe->partnum) {
+		case STMPE610:
+		case STMPE811:
+		case STMPE1601:
+		case STMPE2401:
+		case STMPE2403:
+			edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] +
+				       num_banks - 1 - (offset / 8);
 			ret = stmpe_reg_read(stmpe, edge_det_reg);
 			if (ret < 0)
 				return;
 			edge_det = !!(ret & mask);
+
+		case STMPE1801:
+			rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] -
+				   (offset / 8);
+			fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] -
+				   (offset / 8);
 			ret = stmpe_reg_read(stmpe, rise_reg);
 			if (ret < 0)
 				return;
@@ -268,18 +293,28 @@ static void stmpe_dbg_show_one(struct seq_file *s,
 			if (ret < 0)
 				return;
 			fall = !!(ret & mask);
+
+		case STMPE801:
+			irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] -
+				    (offset / 8);
+			break;
+
+		default:
+			return;
+		}
+
 		ret = stmpe_reg_read(stmpe, irqen_reg);
 		if (ret < 0)
 			return;
 		irqen = !!(ret & mask);
 
-		seq_printf(s, " gpio-%-3d (%-20.20s) in  %s %s %s%s%s",
+		seq_printf(s, " gpio-%-3d (%-20.20s) in  %s %13s %13s %25s %25s",
 			   gpio, label ?: "(none)",
 			   val ? "hi" : "lo",
-			   edge_det ? "edge-asserted" : "edge-inactive",
-			   irqen ? "IRQ-enabled" : "",
-			   rise ? " rising-edge-detection" : "",
-			   fall ? " falling-edge-detection" : "");
+			   edge_det_values[edge_det],
+			   irqen ? "IRQ-enabled" : "IRQ-disabled",
+			   rise_values[rise],
+			   fall_values[fall]);
 	}
 }
 
@@ -338,8 +373,8 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
 
 		stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
 
-		/* Edge detect register is not present on 801 */
-		if (stmpe->partnum != STMPE801)
+		/* Edge detect register is not present on 801 and 1801 */
+		if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801)
 			stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
 					+ i, status[i]);
 	}