arm64: dts: sdm845: add oneplus6/6t devices

Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based
on the sdm845-mtp DT with the following functionality:

 * Touch
 * Display
 * GPU
 * Wlan and Bluetooth
 * USB peripheral mode
 * Remoteproc
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20210114203057.64541-2-caleb@connolly.techSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arch/arm64/boot/dts/qcom/Makefile

@@ -44,6 +44,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-enchilada.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-fajita.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-beryllium.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb

arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/delete-node/ &rmtfs_mem;
+
+/ {
+	aliases {
+		hsuart0 = &uart6;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "Volume keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
+
+		vol-down {
+			label = "Volume down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+
+		vol-up {
+			label = "Volume up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		/*
+		 * The rmtfs memory region in downstream is 'dynamically allocated'
+		 * but given the same address every time. Hard code it as this address is
+		 * where the modem firmware expects it to be.
+		 */
+		rmtfs_mem: memory@f5b01000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xf5b01000 0 0x200000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+
+		/*
+		 * It seems like reserving the old rmtfs_mem region is also needed to prevent
+		 * random crashes which are most likely modem related, more testing needed.
+		 */
+		removed_region: memory@88f00000 {
+			no-map;
+			reg = <0 0x88f00000 0 0x200000>;
+		};
+
+		ramoops: ramoops@ac300000 {
+			compatible = "ramoops";
+			reg = <0 0xac300000 0 0x400000>;
+			record-size = <0x40000>;
+			console-size = <0x40000>;
+			ftrace-size = <0x40000>;
+			pmsg-size = <0x200000>;
+			devinfo-size = <0x1000>;
+			ecc-size = <16>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	/*
+	 * Apparently RPMh does not provide support for PM8998 S4 because it
+	 * is always-on; model it as a fixed regulator.
+	 */
+	vreg_s4a_1p8: pm8998-smps4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	/*
+	 * The touchscreen regulator seems to be controlled somehow by a gpio.
+	 * Model it as a fixed regulator and keep it on. Without schematics we
+	 * don't know how this is actually wired up...
+	 */
+	ts_1p8_supply: ts-1p8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ts_1p8_supply";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 88 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&adsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l9-supply = <&vreg_bob>;
+		vdd-l10-l23-l25-supply = <&vreg_bob>;
+		vdd-l13-l19-l21-supply = <&vreg_bob>;
+		vdd-l16-l28-supply = <&vreg_bob>;
+		vdd-l18-l22-supply = <&vreg_bob>;
+		vdd-l20-l24-supply = <&vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p35>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vdda_mipi_dsi0_pll:
+		vdda_qlink_lv:
+		vdda_ufs1_core:
+		vdda_usb1_ss_core:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_qusb_hs0_1p8:
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p88: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_qusb_hs0_3p1:
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_mipi_dsi0_1p2:
+		vdda_ufs1_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+
+	pm8005-rpmh-regulators {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+	};
+};
+
+&cdsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/*
+	 * Both devices use different panels but all other properties
+	 * are common. Compatible line is declared in device dts.
+	 */
+	display_panel: panel@0 {
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+
+		vddio-supply = <&vreg_l14a_1p88>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+				<GCC_QSPI_CORE_CLK_SRC>,
+				<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				<GCC_LPASS_Q6_AXI_CLK>,
+				<GCC_LPASS_SWAY_CLK>;
+};
+
+&gpu {
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	synaptics-rmi4-i2c@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_default_pins>;
+
+		vdd-supply = <&vreg_l28a_3p0>;
+		vio-supply = <&ts_1p8_supply>;
+
+		syna,reset-delay-ms = <200>;
+		syna,startup-delay-ms = <200>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4_f12: rmi4-f12@12 {
+			reg = <0x12>;
+			touchscreen-x-mm = <68>;
+			touchscreen-y-mm = <144>;
+			syna,sensor-type = <1>;
+			syna,rezero-wait-ms = <200>;
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
+/* Modem/wifi*/
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
+};
+
+&pm8998_gpio {
+	volume_down_gpio: pm8998_gpio5 {
+		pinconf {
+			pins = "gpio5";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,drive-strength = <0>;
+		};
+	};
+
+	volume_up_gpio: pm8998_gpio6 {
+		pinconf {
+			pins = "gpio6";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,drive-strength = <0>;
+		};
+	};
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qup_i2c12_default {
+	mux {
+		pins = "gpio49", "gpio50";
+		function = "qup12";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qup_i2c10_default {
+	pinconf {
+		pins = "gpio55", "gpio56";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qup_uart9_default {
+	pinconf-tx {
+		pins = "gpio4";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		pins = "gpio5";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+/*
+ * Prevent garbage data on bluetooth UART lines
+ */
+&qup_uart6_default {
+	pinmux {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "qup6";
+	};
+
+	cts {
+		pins = "gpio45";
+		bias-pull-down;
+	};
+
+	rts-tx {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio48";
+		bias-pull-up;
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		/*
+		 * This path is relative to the qca/
+		 * subdir under lib/firmware.
+		 */
+		firmware-name = "oneplus6/crnv21.bin";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+
+	/*
+	 * disable USB3 clock requirement as the device only supports
+	 * USB2.
+	 */
+	qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+	/*
+	 * We don't have the capability to switch modes yet.
+	 */
+	dr_mode = "peripheral";
+
+	/* fastest mode for USB 2 */
+	maximum-speed = "high-speed";
+
+	/* Remove USB3 phy as it's unused on this device. */
+	phys = <&usb_1_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vdda_usb1_ss_core>;
+	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	tri_state_key_default: tri_state_key_default {
+		mux {
+			pins = "gpio40", "gpio42", "gpio26";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	ts_default_pins: ts-int {
+		mux {
+			pins = "gpio99", "gpio125";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+
+	panel_reset_pins: panel-reset {
+		mux {
+			pins = "gpio6", "gpio25", "gpio26";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable = <0>;
+		};
+	};
+
+	panel_te_pin: panel-te {
+		mux {
+			pins = "gpio10";
+			function = "mdp_vsync";
+			drive-strength = <2>;
+			bias-disable;
+			input-enable;
+		};
+	};
+
+	panel_esd_pin: panel-esd {
+		mux {
+			pins = "gpio30";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+			input-enable;
+		};
+	};
+};
+
+&wifi {
+	status = "okay";
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
+};

arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6 (enchilada) device tree.
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "sdm845-oneplus-common.dtsi"
+
+/ {
+	model = "OnePlus 6";
+	compatible = "oneplus,enchilada", "qcom,sdm845";
+};
+
+&display_panel {
+	status = "okay";
+
+	compatible = "samsung,sofef00";
+};

arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6T (fajita) device tree.
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "sdm845-oneplus-common.dtsi"
+
+/ {
+	model = "OnePlus 6T";
+	compatible = "oneplus,fajita", "qcom,sdm845";
+};
+
+&display_panel {
+	status = "okay";
+
+	compatible = "samsung,s6e3fc2x01";
+};
+
+&rmi4_f12 {
+	touchscreen-y-mm = <148>;
+};