Commit 28d5bdbe authored by Markus Pargmann's avatar Markus Pargmann Committed by Mauro Carvalho Chehab

[media] mt9v032: Add reset and standby gpios

Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().

The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: default avatarMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: default avatarPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: default avatarRob Herring <robh@kernel.org>
Acked-by: default avatarLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@osg.samsung.com>
parent c1ae8f3a
...@@ -20,6 +20,8 @@ Optional Properties: ...@@ -20,6 +20,8 @@ Optional Properties:
- link-frequencies: List of allowed link frequencies in Hz. Each frequency is - link-frequencies: List of allowed link frequencies in Hz. Each frequency is
expressed as a 64-bit big-endian integer. expressed as a 64-bit big-endian integer.
- reset-gpios: GPIO handle which is connected to the reset pin of the chip.
- standby-gpios: GPIO handle which is connected to the standby pin of the chip.
For further reading on port node refer to For further reading on port node refer to
Documentation/devicetree/bindings/media/video-interfaces.txt. Documentation/devicetree/bindings/media/video-interfaces.txt.
......
...@@ -14,6 +14,7 @@ ...@@ -14,6 +14,7 @@
#include <linux/clk.h> #include <linux/clk.h>
#include <linux/delay.h> #include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/i2c.h> #include <linux/i2c.h>
#include <linux/log2.h> #include <linux/log2.h>
#include <linux/mutex.h> #include <linux/mutex.h>
...@@ -251,6 +252,8 @@ struct mt9v032 { ...@@ -251,6 +252,8 @@ struct mt9v032 {
struct regmap *regmap; struct regmap *regmap;
struct clk *clk; struct clk *clk;
struct gpio_desc *reset_gpio;
struct gpio_desc *standby_gpio;
struct mt9v032_platform_data *pdata; struct mt9v032_platform_data *pdata;
const struct mt9v032_model_info *model; const struct mt9v032_model_info *model;
...@@ -312,16 +315,31 @@ static int mt9v032_power_on(struct mt9v032 *mt9v032) ...@@ -312,16 +315,31 @@ static int mt9v032_power_on(struct mt9v032 *mt9v032)
struct regmap *map = mt9v032->regmap; struct regmap *map = mt9v032->regmap;
int ret; int ret;
if (mt9v032->reset_gpio)
gpiod_set_value_cansleep(mt9v032->reset_gpio, 1);
ret = clk_set_rate(mt9v032->clk, mt9v032->sysclk); ret = clk_set_rate(mt9v032->clk, mt9v032->sysclk);
if (ret < 0) if (ret < 0)
return ret; return ret;
/* System clock has to be enabled before releasing the reset */
ret = clk_prepare_enable(mt9v032->clk); ret = clk_prepare_enable(mt9v032->clk);
if (ret) if (ret)
return ret; return ret;
udelay(1); udelay(1);
if (mt9v032->reset_gpio) {
gpiod_set_value_cansleep(mt9v032->reset_gpio, 0);
/* After releasing reset we need to wait 10 clock cycles
* before accessing the sensor over I2C. As the minimum SYSCLK
* frequency is 13MHz, waiting 1µs will be enough in the worst
* case.
*/
udelay(1);
}
/* Reset the chip and stop data read out */ /* Reset the chip and stop data read out */
ret = regmap_write(map, MT9V032_RESET, 1); ret = regmap_write(map, MT9V032_RESET, 1);
if (ret < 0) if (ret < 0)
...@@ -954,6 +972,16 @@ static int mt9v032_probe(struct i2c_client *client, ...@@ -954,6 +972,16 @@ static int mt9v032_probe(struct i2c_client *client,
if (IS_ERR(mt9v032->clk)) if (IS_ERR(mt9v032->clk))
return PTR_ERR(mt9v032->clk); return PTR_ERR(mt9v032->clk);
mt9v032->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
GPIOD_OUT_HIGH);
if (IS_ERR(mt9v032->reset_gpio))
return PTR_ERR(mt9v032->reset_gpio);
mt9v032->standby_gpio = devm_gpiod_get_optional(&client->dev, "standby",
GPIOD_OUT_LOW);
if (IS_ERR(mt9v032->standby_gpio))
return PTR_ERR(mt9v032->standby_gpio);
mutex_init(&mt9v032->power_lock); mutex_init(&mt9v032->power_lock);
mt9v032->pdata = pdata; mt9v032->pdata = pdata;
mt9v032->model = (const void *)did->driver_data; mt9v032->model = (const void *)did->driver_data;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment