Commit 28e5d3bb authored by William Breathitt Gray's avatar William Breathitt Gray Committed by Jonathan Cameron

iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8

The ACCES 104-QUAD-8 is a general purpose quadrature encoder
counter/interface board. The 104-QUAD-8 is capable of monitoring the
outputs of eight encoders via four on-board LSI/CSI LS7266R1 24-bit
dual-axis quadrature counter chips. Core functions handled by the
LS7266R1, such as direction and total count, are available.

Performing a write to a counter's IIO_CHAN_INFO_RAW sets the counter and
also clears the counter's respective error flag. Although the counters
have a 25-bit range, only the lower 24 bits may be set, either directly
or via a counter's preset attribute. Interrupts are not supported by
this driver.

This driver adds IIO support for the ACCES 104-QUAD-8 and ACCES
104-QUAD-4. The base port addresses for the devices may be configured
via the base array module parameter.
Signed-off-by: default avatarWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: default avatarJonathan Cameron <jic23@kernel.org>
parent 1a8f324a
What: /sys/bus/iio/devices/iio:deviceX/in_count_count_direction_available
What: /sys/bus/iio/devices/iio:deviceX/in_count_count_mode_available
What: /sys/bus/iio/devices/iio:deviceX/in_count_noise_error_available
What: /sys/bus/iio/devices/iio:deviceX/in_count_quadrature_mode_available
What: /sys/bus/iio/devices/iio:deviceX/in_index_index_polarity_available
What: /sys/bus/iio/devices/iio:deviceX/in_index_synchronous_mode_available
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Discrete set of available values for the respective counter
configuration are listed in this file.
What: /sys/bus/iio/devices/iio:deviceX/in_countY_count_direction
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Read-only attribute that indicates whether the counter for
channel Y is counting up or down.
What: /sys/bus/iio/devices/iio:deviceX/in_countY_count_mode
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Count mode for channel Y. Four count modes are available:
normal, range limit, non-recycle, and modulo-n. The preset value
for channel Y is used by the count mode where required.
Normal:
Counting is continuous in either direction.
Range Limit:
An upper or lower limit is set, mimicking limit switches
in the mechanical counterpart. The upper limit is set to
the preset value, while the lower limit is set to 0. The
counter freezes at count = preset when counting up, and
at count = 0 when counting down. At either of these
limits, the counting is resumed only when the count
direction is reversed.
Non-recycle:
Counter is disabled whenever a 24-bit count overflow or
underflow takes place. The counter is re-enabled when a
new count value is loaded to the counter via a preset
operation or write to raw.
Modulo-N:
A count boundary is set between 0 and the preset value.
The counter is reset to 0 at count = preset when
counting up, while the counter is set to the preset
value at count = 0 when counting down; the counter does
not freeze at the bundary points, but counts
continuously throughout.
What: /sys/bus/iio/devices/iio:deviceX/in_countY_noise_error
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Read-only attribute that indicates whether excessive noise is
present at the channel Y count inputs in quadrature clock mode;
irrelevant in non-quadrature clock mode.
What: /sys/bus/iio/devices/iio:deviceX/in_countY_preset
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
If the counter device supports preset registers, the preset
count for channel Y is provided by this attribute.
What: /sys/bus/iio/devices/iio:deviceX/in_countY_quadrature_mode
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Configure channel Y counter for non-quadrature or quadrature
clock mode. Selecting non-quadrature clock mode will disable
synchronous load mode. In quadrature clock mode, the channel Y
scale attribute selects the encoder phase division (scale of 1
selects full-cycle, scale of 0.5 selects half-cycle, scale of
0.25 selects quarter-cycle) processed by the channel Y counter.
Non-quadrature:
The filter and decoder circuit are bypassed. Encoder A
input serves as the count input and B as the UP/DOWN
direction control input, with B = 1 selecting UP Count
mode and B = 0 selecting Down Count mode.
Quadrature:
Encoder A and B inputs are digitally filtered and
decoded for UP/DN clock.
What: /sys/bus/iio/devices/iio:deviceX/in_countY_set_to_preset_on_index
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Whether to set channel Y counter with channel Y preset value
when channel Y index input is active, or continuously count.
Valid attribute values are boolean.
What: /sys/bus/iio/devices/iio:deviceX/in_indexY_index_polarity
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Active level of channel Y index input; irrelevant in
non-synchronous load mode.
What: /sys/bus/iio/devices/iio:deviceX/in_indexY_synchronous_mode
KernelVersion: 4.9
Contact: linux-iio@vger.kernel.org
Description:
Configure channel Y counter for non-synchronous or synchronous
load mode. Synchronous load mode cannot be selected in
non-quadrature clock mode.
Non-synchronous:
A logic low level is the active level at this index
input. The index function (as enabled via
set_to_preset_on_index) is performed directly on the
active level of the index input.
Synchronous:
Intended for interfacing with encoder Index output in
quadrature clock mode. The active level is configured
via index_polarity. The index function (as enabled via
set_to_preset_on_index) is performed synchronously with
the quadrature clock on the active level of the index
input.
...@@ -255,6 +255,12 @@ L: linux-gpio@vger.kernel.org ...@@ -255,6 +255,12 @@ L: linux-gpio@vger.kernel.org
S: Maintained S: Maintained
F: drivers/gpio/gpio-104-idio-16.c F: drivers/gpio/gpio-104-idio-16.c
ACCES 104-QUAD-8 IIO DRIVER
M: William Breathitt Gray <vilhelm.gray@gmail.com>
L: linux-iio@vger.kernel.org
S: Maintained
F: drivers/iio/counter/104-quad-8.c
ACENIC DRIVER ACENIC DRIVER
M: Jes Sorensen <jes@trained-monkey.org> M: Jes Sorensen <jes@trained-monkey.org>
L: linux-acenic@sunsite.dk L: linux-acenic@sunsite.dk
......
...@@ -73,6 +73,7 @@ source "drivers/iio/adc/Kconfig" ...@@ -73,6 +73,7 @@ source "drivers/iio/adc/Kconfig"
source "drivers/iio/amplifiers/Kconfig" source "drivers/iio/amplifiers/Kconfig"
source "drivers/iio/chemical/Kconfig" source "drivers/iio/chemical/Kconfig"
source "drivers/iio/common/Kconfig" source "drivers/iio/common/Kconfig"
source "drivers/iio/counter/Kconfig"
source "drivers/iio/dac/Kconfig" source "drivers/iio/dac/Kconfig"
source "drivers/iio/dummy/Kconfig" source "drivers/iio/dummy/Kconfig"
source "drivers/iio/frequency/Kconfig" source "drivers/iio/frequency/Kconfig"
......
...@@ -18,6 +18,7 @@ obj-y += amplifiers/ ...@@ -18,6 +18,7 @@ obj-y += amplifiers/
obj-y += buffer/ obj-y += buffer/
obj-y += chemical/ obj-y += chemical/
obj-y += common/ obj-y += common/
obj-y += counter/
obj-y += dac/ obj-y += dac/
obj-y += dummy/ obj-y += dummy/
obj-y += gyro/ obj-y += gyro/
......
/*
* IIO driver for the ACCES 104-QUAD-8
* Copyright (C) 2016 William Breathitt Gray
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License, version 2, as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* This driver supports the ACCES 104-QUAD-8 and ACCES 104-QUAD-4.
*/
#include <linux/bitops.h>
#include <linux/device.h>
#include <linux/errno.h>
#include <linux/iio/iio.h>
#include <linux/iio/types.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/isa.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/types.h>
#define QUAD8_EXTENT 32
static unsigned int base[max_num_isa_dev(QUAD8_EXTENT)];
static unsigned int num_quad8;
module_param_array(base, uint, &num_quad8, 0);
MODULE_PARM_DESC(base, "ACCES 104-QUAD-8 base addresses");
#define QUAD8_NUM_COUNTERS 8
/**
* struct quad8_iio - IIO device private data structure
* @preset: array of preset values
* @count_mode: array of count mode configurations
* @quadrature_mode: array of quadrature mode configurations
* @quadrature_scale: array of quadrature mode scale configurations
* @ab_enable: array of A and B inputs enable configurations
* @preset_enable: array of set_to_preset_on_index attribute configurations
* @synchronous_mode: array of index function synchronous mode configurations
* @index_polarity: array of index function polarity configurations
* @base: base port address of the IIO device
*/
struct quad8_iio {
unsigned int preset[QUAD8_NUM_COUNTERS];
unsigned int count_mode[QUAD8_NUM_COUNTERS];
unsigned int quadrature_mode[QUAD8_NUM_COUNTERS];
unsigned int quadrature_scale[QUAD8_NUM_COUNTERS];
unsigned int ab_enable[QUAD8_NUM_COUNTERS];
unsigned int preset_enable[QUAD8_NUM_COUNTERS];
unsigned int synchronous_mode[QUAD8_NUM_COUNTERS];
unsigned int index_polarity[QUAD8_NUM_COUNTERS];
unsigned int base;
};
static int quad8_read_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan, int *val, int *val2, long mask)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const int base_offset = priv->base + 2 * chan->channel;
unsigned int flags;
unsigned int borrow;
unsigned int carry;
int i;
switch (mask) {
case IIO_CHAN_INFO_RAW:
if (chan->type == IIO_INDEX) {
*val = !!(inb(priv->base + 0x16) & BIT(chan->channel));
return IIO_VAL_INT;
}
flags = inb(base_offset);
borrow = flags & BIT(0);
carry = !!(flags & BIT(1));
/* Borrow XOR Carry effectively doubles count range */
*val = (borrow ^ carry) << 24;
/* Reset Byte Pointer; transfer Counter to Output Latch */
outb(0x11, base_offset + 1);
for (i = 0; i < 3; i++)
*val |= (unsigned int)inb(base_offset) << (8 * i);
return IIO_VAL_INT;
case IIO_CHAN_INFO_ENABLE:
*val = priv->ab_enable[chan->channel];
return IIO_VAL_INT;
case IIO_CHAN_INFO_SCALE:
*val = 1;
*val2 = priv->quadrature_scale[chan->channel];
return IIO_VAL_FRACTIONAL_LOG2;
}
return -EINVAL;
}
static int quad8_write_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan, int val, int val2, long mask)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const int base_offset = priv->base + 2 * chan->channel;
int i;
unsigned int ior_cfg;
switch (mask) {
case IIO_CHAN_INFO_RAW:
if (chan->type == IIO_INDEX)
return -EINVAL;
/* Only 24-bit values are supported */
if ((unsigned int)val > 0xFFFFFF)
return -EINVAL;
/* Reset Byte Pointer */
outb(0x01, base_offset + 1);
/* Counter can only be set via Preset Register */
for (i = 0; i < 3; i++)
outb(val >> (8 * i), base_offset);
/* Transfer Preset Register to Counter */
outb(0x08, base_offset + 1);
/* Reset Byte Pointer */
outb(0x01, base_offset + 1);
/* Set Preset Register back to original value */
val = priv->preset[chan->channel];
for (i = 0; i < 3; i++)
outb(val >> (8 * i), base_offset);
/* Reset Borrow, Carry, Compare, and Sign flags */
outb(0x02, base_offset + 1);
/* Reset Error flag */
outb(0x06, base_offset + 1);
return 0;
case IIO_CHAN_INFO_ENABLE:
/* only boolean values accepted */
if (val < 0 || val > 1)
return -EINVAL;
priv->ab_enable[chan->channel] = val;
ior_cfg = val | priv->preset_enable[chan->channel] << 1;
/* Load I/O control configuration */
outb(0x40 | ior_cfg, base_offset);
return 0;
case IIO_CHAN_INFO_SCALE:
/* Quadrature scaling only available in quadrature mode */
if (!priv->quadrature_mode[chan->channel] && (val2 || val != 1))
return -EINVAL;
/* Only three gain states (1, 0.5, 0.25) */
if (val == 1 && !val2)
priv->quadrature_scale[chan->channel] = 0;
else if (!val)
switch (val2) {
case 500000:
priv->quadrature_scale[chan->channel] = 1;
break;
case 250000:
priv->quadrature_scale[chan->channel] = 2;
break;
default:
return -EINVAL;
}
else
return -EINVAL;
return 0;
}
return -EINVAL;
}
static const struct iio_info quad8_info = {
.driver_module = THIS_MODULE,
.read_raw = quad8_read_raw,
.write_raw = quad8_write_raw
};
static ssize_t quad8_read_preset(struct iio_dev *indio_dev, uintptr_t private,
const struct iio_chan_spec *chan, char *buf)
{
const struct quad8_iio *const priv = iio_priv(indio_dev);
return snprintf(buf, PAGE_SIZE, "%u\n", priv->preset[chan->channel]);
}
static ssize_t quad8_write_preset(struct iio_dev *indio_dev, uintptr_t private,
const struct iio_chan_spec *chan, const char *buf, size_t len)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const int base_offset = priv->base + 2 * chan->channel;
unsigned int preset;
int ret;
int i;
ret = kstrtouint(buf, 0, &preset);
if (ret)
return ret;
/* Only 24-bit values are supported */
if (preset > 0xFFFFFF)
return -EINVAL;
priv->preset[chan->channel] = preset;
/* Reset Byte Pointer */
outb(0x01, base_offset + 1);
/* Set Preset Register */
for (i = 0; i < 3; i++)
outb(preset >> (8 * i), base_offset);
return len;
}
static ssize_t quad8_read_set_to_preset_on_index(struct iio_dev *indio_dev,
uintptr_t private, const struct iio_chan_spec *chan, char *buf)
{
const struct quad8_iio *const priv = iio_priv(indio_dev);
return snprintf(buf, PAGE_SIZE, "%u\n",
priv->preset_enable[chan->channel]);
}
static ssize_t quad8_write_set_to_preset_on_index(struct iio_dev *indio_dev,
uintptr_t private, const struct iio_chan_spec *chan, const char *buf,
size_t len)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const int base_offset = priv->base + 2 * chan->channel;
bool preset_enable;
int ret;
unsigned int ior_cfg;
ret = kstrtobool(buf, &preset_enable);
if (ret)
return ret;
priv->preset_enable[chan->channel] = preset_enable;
ior_cfg = priv->ab_enable[chan->channel] |
(unsigned int)preset_enable << 1;
/* Load I/O control configuration to Input / Output Control Register */
outb(0x40 | ior_cfg, base_offset);
return len;
}
static const char *const quad8_noise_error_states[] = {
"No excessive noise is present at the count inputs",
"Excessive noise is present at the count inputs"
};
static int quad8_get_noise_error(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const int base_offset = priv->base + 2 * chan->channel + 1;
return !!(inb(base_offset) & BIT(4));
}
static const struct iio_enum quad8_noise_error_enum = {
.items = quad8_noise_error_states,
.num_items = ARRAY_SIZE(quad8_noise_error_states),
.get = quad8_get_noise_error
};
static const char *const quad8_count_direction_states[] = {
"down",
"up"
};
static int quad8_get_count_direction(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const int base_offset = priv->base + 2 * chan->channel + 1;
return !!(inb(base_offset) & BIT(5));
}
static const struct iio_enum quad8_count_direction_enum = {
.items = quad8_count_direction_states,
.num_items = ARRAY_SIZE(quad8_count_direction_states),
.get = quad8_get_count_direction
};
static const char *const quad8_count_modes[] = {
"normal",
"range limit",
"non-recycle",
"modulo-n"
};
static int quad8_set_count_mode(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, unsigned int count_mode)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
unsigned int mode_cfg = count_mode << 1;
const int base_offset = priv->base + 2 * chan->channel + 1;
priv->count_mode[chan->channel] = count_mode;
/* Add quadrature mode configuration */
if (priv->quadrature_mode[chan->channel])
mode_cfg |= (priv->quadrature_scale[chan->channel] + 1) << 3;
/* Load mode configuration to Counter Mode Register */
outb(0x20 | mode_cfg, base_offset);
return 0;
}
static int quad8_get_count_mode(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
const struct quad8_iio *const priv = iio_priv(indio_dev);
return priv->count_mode[chan->channel];
}
static const struct iio_enum quad8_count_mode_enum = {
.items = quad8_count_modes,
.num_items = ARRAY_SIZE(quad8_count_modes),
.set = quad8_set_count_mode,
.get = quad8_get_count_mode
};
static const char *const quad8_synchronous_modes[] = {
"non-synchronous",
"synchronous"
};
static int quad8_set_synchronous_mode(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, unsigned int synchronous_mode)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const unsigned int idr_cfg = synchronous_mode |
priv->index_polarity[chan->channel] << 1;
const int base_offset = priv->base + 2 * chan->channel + 1;
/* Index function must be non-synchronous in non-quadrature mode */
if (synchronous_mode && !priv->quadrature_mode[chan->channel])
return -EINVAL;
priv->synchronous_mode[chan->channel] = synchronous_mode;
/* Load Index Control configuration to Index Control Register */
outb(0x40 | idr_cfg, base_offset);
return 0;
}
static int quad8_get_synchronous_mode(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
const struct quad8_iio *const priv = iio_priv(indio_dev);
return priv->synchronous_mode[chan->channel];
}
static const struct iio_enum quad8_synchronous_mode_enum = {
.items = quad8_synchronous_modes,
.num_items = ARRAY_SIZE(quad8_synchronous_modes),
.set = quad8_set_synchronous_mode,
.get = quad8_get_synchronous_mode
};
static const char *const quad8_quadrature_modes[] = {
"non-quadrature",
"quadrature"
};
static int quad8_set_quadrature_mode(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, unsigned int quadrature_mode)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
unsigned int mode_cfg = priv->count_mode[chan->channel] << 1;
const int base_offset = priv->base + 2 * chan->channel + 1;
if (quadrature_mode)
mode_cfg |= (priv->quadrature_scale[chan->channel] + 1) << 3;
else {
/* Quadrature scaling only available in quadrature mode */
priv->quadrature_scale[chan->channel] = 0;
/* Synchronous function not supported in non-quadrature mode */
if (priv->synchronous_mode[chan->channel])
quad8_set_synchronous_mode(indio_dev, chan, 0);
}
priv->quadrature_mode[chan->channel] = quadrature_mode;
/* Load mode configuration to Counter Mode Register */
outb(0x20 | mode_cfg, base_offset);
return 0;
}
static int quad8_get_quadrature_mode(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
const struct quad8_iio *const priv = iio_priv(indio_dev);
return priv->quadrature_mode[chan->channel];
}
static const struct iio_enum quad8_quadrature_mode_enum = {
.items = quad8_quadrature_modes,
.num_items = ARRAY_SIZE(quad8_quadrature_modes),
.set = quad8_set_quadrature_mode,
.get = quad8_get_quadrature_mode
};
static const char *const quad8_index_polarity_modes[] = {
"negative",
"positive"
};
static int quad8_set_index_polarity(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, unsigned int index_polarity)
{
struct quad8_iio *const priv = iio_priv(indio_dev);
const unsigned int idr_cfg = priv->synchronous_mode[chan->channel] |
index_polarity << 1;
const int base_offset = priv->base + 2 * chan->channel + 1;
priv->index_polarity[chan->channel] = index_polarity;
/* Load Index Control configuration to Index Control Register */
outb(0x40 | idr_cfg, base_offset);
return 0;
}
static int quad8_get_index_polarity(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
const struct quad8_iio *const priv = iio_priv(indio_dev);
return priv->index_polarity[chan->channel];
}
static const struct iio_enum quad8_index_polarity_enum = {
.items = quad8_index_polarity_modes,
.num_items = ARRAY_SIZE(quad8_index_polarity_modes),
.set = quad8_set_index_polarity,
.get = quad8_get_index_polarity
};
static const struct iio_chan_spec_ext_info quad8_count_ext_info[] = {
{
.name = "preset",
.shared = IIO_SEPARATE,
.read = quad8_read_preset,
.write = quad8_write_preset
},
{
.name = "set_to_preset_on_index",
.shared = IIO_SEPARATE,
.read = quad8_read_set_to_preset_on_index,
.write = quad8_write_set_to_preset_on_index
},
IIO_ENUM("noise_error", IIO_SEPARATE, &quad8_noise_error_enum),
IIO_ENUM_AVAILABLE("noise_error", &quad8_noise_error_enum),
IIO_ENUM("count_direction", IIO_SEPARATE, &quad8_count_direction_enum),
IIO_ENUM_AVAILABLE("count_direction", &quad8_count_direction_enum),
IIO_ENUM("count_mode", IIO_SEPARATE, &quad8_count_mode_enum),
IIO_ENUM_AVAILABLE("count_mode", &quad8_count_mode_enum),
IIO_ENUM("quadrature_mode", IIO_SEPARATE, &quad8_quadrature_mode_enum),
IIO_ENUM_AVAILABLE("quadrature_mode", &quad8_quadrature_mode_enum),
{}
};
static const struct iio_chan_spec_ext_info quad8_index_ext_info[] = {
IIO_ENUM("synchronous_mode", IIO_SEPARATE,
&quad8_synchronous_mode_enum),
IIO_ENUM_AVAILABLE("synchronous_mode", &quad8_synchronous_mode_enum),
IIO_ENUM("index_polarity", IIO_SEPARATE, &quad8_index_polarity_enum),
IIO_ENUM_AVAILABLE("index_polarity", &quad8_index_polarity_enum),
{}
};
#define QUAD8_COUNT_CHAN(_chan) { \
.type = IIO_COUNT, \
.channel = (_chan), \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
BIT(IIO_CHAN_INFO_ENABLE) | BIT(IIO_CHAN_INFO_SCALE), \
.ext_info = quad8_count_ext_info, \
.indexed = 1 \
}
#define QUAD8_INDEX_CHAN(_chan) { \
.type = IIO_INDEX, \
.channel = (_chan), \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
.ext_info = quad8_index_ext_info, \
.indexed = 1 \
}
static const struct iio_chan_spec quad8_channels[] = {
QUAD8_COUNT_CHAN(0), QUAD8_INDEX_CHAN(0),
QUAD8_COUNT_CHAN(1), QUAD8_INDEX_CHAN(1),
QUAD8_COUNT_CHAN(2), QUAD8_INDEX_CHAN(2),
QUAD8_COUNT_CHAN(3), QUAD8_INDEX_CHAN(3),
QUAD8_COUNT_CHAN(4), QUAD8_INDEX_CHAN(4),
QUAD8_COUNT_CHAN(5), QUAD8_INDEX_CHAN(5),
QUAD8_COUNT_CHAN(6), QUAD8_INDEX_CHAN(6),
QUAD8_COUNT_CHAN(7), QUAD8_INDEX_CHAN(7)
};
static int quad8_probe(struct device *dev, unsigned int id)
{
struct iio_dev *indio_dev;
struct quad8_iio *priv;
int i, j;
unsigned int base_offset;
indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
if (!indio_dev)
return -ENOMEM;
if (!devm_request_region(dev, base[id], QUAD8_EXTENT,
dev_name(dev))) {
dev_err(dev, "Unable to lock port addresses (0x%X-0x%X)\n",
base[id], base[id] + QUAD8_EXTENT);
return -EBUSY;
}
indio_dev->info = &quad8_info;
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->num_channels = ARRAY_SIZE(quad8_channels);
indio_dev->channels = quad8_channels;
indio_dev->name = dev_name(dev);
priv = iio_priv(indio_dev);
priv->base = base[id];
/* Reset all counters and disable interrupt function */
outb(0x01, base[id] + 0x11);
/* Set initial configuration for all counters */
for (i = 0; i < QUAD8_NUM_COUNTERS; i++) {
base_offset = base[id] + 2 * i;
/* Reset Byte Pointer */
outb(0x01, base_offset + 1);
/* Reset Preset Register */
for (j = 0; j < 3; j++)
outb(0x00, base_offset);
/* Reset Borrow, Carry, Compare, and Sign flags */
outb(0x04, base_offset + 1);
/* Reset Error flag */
outb(0x06, base_offset + 1);
/* Binary encoding; Normal count; non-quadrature mode */
outb(0x20, base_offset + 1);
/* Disable A and B inputs; preset on index; FLG1 as Carry */
outb(0x40, base_offset + 1);
/* Disable index function; negative index polarity */
outb(0x60, base_offset + 1);
}
/* Enable all counters */
outb(0x00, base[id] + 0x11);
return devm_iio_device_register(dev, indio_dev);
}
static struct isa_driver quad8_driver = {
.probe = quad8_probe,
.driver = {
.name = "104-quad-8"
}
};
module_isa_driver(quad8_driver, num_quad8);
MODULE_AUTHOR("William Breathitt Gray <vilhelm.gray@gmail.com>");
MODULE_DESCRIPTION("ACCES 104-QUAD-8 IIO driver");
MODULE_LICENSE("GPL v2");
#
# Counter devices
#
# When adding new entries keep the list in alphabetical order
menu "Counters"
config 104_QUAD_8
tristate "ACCES 104-QUAD-8 driver"
depends on X86 && ISA_BUS_API
help
Say yes here to build support for the ACCES 104-QUAD-8 quadrature
encoder counter/interface device family (104-QUAD-8, 104-QUAD-4).
Performing a write to a counter's IIO_CHAN_INFO_RAW sets the counter and
also clears the counter's respective error flag. Although the counters
have a 25-bit range, only the lower 24 bits may be set, either directly
or via a counter's preset attribute. Interrupts are not supported by
this driver.
The base port addresses for the devices may be configured via the base
array module parameter.
endmenu
#
# Makefile for IIO counter devices
#
# When adding new entries keep the list in alphabetical order
obj-$(CONFIG_104_QUAD_8) += 104-quad-8.o
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment