power: supply: axp288_fuel_gauge: Rework get_status()

Relying on the (dis)charge current reporting for reporting FULL back to
userspace does not work really well and often leads to the reported status
getting stuck at e.g. 98/99% (the fuelgauge is not perfect) for hours.

What happens is that when the battery is full the axp288 keeps charging it
with a very low current. Until it is really really full and once really
really full, some inaccuracies in the adc lead to it then sometimes
reporting a small discharging rate, even though an external pwr source is
used. So we end up with a status of "charging" for hours after the battery
is actually already full and sometimes this then flip-flops to discharging.

This commit fixes this by first checking if a valid Vbus is present and if
it is present using the fuel-gauge's reported percentage to check for a
full battery.

This commit also changes how get_status() determines if the battery is
charging or discharging when not reporting it as full. We still use the
current direction for this, but instead of reading 4 extra registers for
this (2 16 bit regs), simplify things by using the current-direction bit
in the power-status register, which already gets read anyways.

This also reduces the amount of i2c reads to 1 when on battery and 2
when a valid Vbus is present.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>

drivers/power/supply/axp288_fuel_gauge.c

@@ -32,6 +32,12 @@
 #include <linux/seq_file.h>
 #include <asm/unaligned.h>
 
+#define PS_STAT_VBUS_TRIGGER		(1 << 0)
+#define PS_STAT_BAT_CHRG_DIR		(1 << 2)
+#define PS_STAT_VBAT_ABOVE_VHOLD	(1 << 3)
+#define PS_STAT_VBUS_VALID		(1 << 4)
+#define PS_STAT_VBUS_PRESENT		(1 << 5)
+
 #define CHRG_STAT_BAT_SAFE_MODE		(1 << 3)
 #define CHRG_STAT_BAT_VALID			(1 << 4)
 #define CHRG_STAT_BAT_PRESENT		(1 << 5)
@@ -336,8 +342,7 @@ static inline void fuel_gauge_remove_debugfs(struct axp288_fg_info *info)
 
 static void fuel_gauge_get_status(struct axp288_fg_info *info)
 {
-	int pwr_stat, ret;
-	int charge, discharge;
+	int pwr_stat, fg_res;
 
 	pwr_stat = fuel_gauge_reg_readb(info, AXP20X_PWR_INPUT_STATUS);
 	if (pwr_stat < 0) {
@@ -345,29 +350,25 @@ static void fuel_gauge_get_status(struct axp288_fg_info *info)
 			"PWR STAT read failed:%d\n", pwr_stat);
 		return;
 	}
-	ret = iio_read_channel_raw(info->iio_channel[BAT_CHRG_CURR], &charge);
-	if (ret < 0) {
+
+	/* Report full if Vbus is valid and the reported capacity is 100% */
+	if (pwr_stat & PS_STAT_VBUS_VALID) {
+		fg_res = fuel_gauge_reg_readb(info, AXP20X_FG_RES);
+		if (fg_res < 0) {
 			dev_err(&info->pdev->dev,
-			"ADC charge current read failed:%d\n", ret);
+				"FG RES read failed: %d\n", fg_res);
 			return;
 		}
-	ret = iio_read_channel_raw(info->iio_channel[BAT_D_CURR], &discharge);
-	if (ret < 0) {
-		dev_err(&info->pdev->dev,
-			"ADC discharge current read failed:%d\n", ret);
+		if (fg_res == (FG_REP_CAP_VALID | 100)) {
+			info->status = POWER_SUPPLY_STATUS_FULL;
 			return;
 		}
+	}
 
-	if (charge > 0)
+	if (pwr_stat & PS_STAT_BAT_CHRG_DIR)
 		info->status = POWER_SUPPLY_STATUS_CHARGING;
-	else if (discharge > 0)
-		info->status = POWER_SUPPLY_STATUS_DISCHARGING;
-	else {
-		if (pwr_stat & CHRG_STAT_BAT_PRESENT)
-			info->status = POWER_SUPPLY_STATUS_FULL;
 	else
-			info->status = POWER_SUPPLY_STATUS_NOT_CHARGING;
-	}
+		info->status = POWER_SUPPLY_STATUS_DISCHARGING;
 }
 
 static int fuel_gauge_get_vbatt(struct axp288_fg_info *info, int *vbatt)