Merge tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc

Pull MMC fixes from Ulf Hansson:
 "Here are some mmc fixes intended for v4.5 rc1.

  MMC core:
   - Restore reset-gpios to be optional in pwrseq_simple
   - Allow SDIO tuple for CISTPL_SDIO_STD
   - Print correct voltage value in debugfs
   - Enable tuning according to the actual timing
   - Limit SD card power limit according to cards capabilities

  MMC host:
   - tmio_mmc_dma: don't print invalid DMA cookie
   - mmci: Pick the correct variant and allow 8-bit mode for Nomadik"

* tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: pwrseq_simple: Make reset-gpios optional to match doc
  mmc: sdio_cis: fix unknown tuple for CISTPL_SDIO_STD
  mmc: debugfs: correct wrong voltage value
  mmc: tmio_mmc_dma: don't print invalid DMA cookie
  mmc: core: Enable tuning according to the actual timing
  mmc: mmci: support 8bit mode on the Nomadik
  mmc: mmci: fix an ages old detection error
  mmc: sd: limit SD card power limit according to cards capabilities

drivers/mmc/core/debugfs.c

@@ -170,7 +170,7 @@ static int mmc_ios_show(struct seq_file *s, void *data)
 		str = "invalid";
 		break;
 	}
-	seq_printf(s, "signal voltage:\t%u (%s)\n", ios->chip_select, str);
+	seq_printf(s, "signal voltage:\t%u (%s)\n", ios->signal_voltage, str);
 
 	switch (ios->drv_type) {
 	case MMC_SET_DRIVER_TYPE_A:

drivers/mmc/core/pwrseq_simple.c

@@ -29,15 +29,18 @@ struct mmc_pwrseq_simple {
 static void mmc_pwrseq_simple_set_gpios_value(struct mmc_pwrseq_simple *pwrseq,
 					      int value)
 {
-	int i;
 	struct gpio_descs *reset_gpios = pwrseq->reset_gpios;
+
+	if (!IS_ERR(reset_gpios)) {
+		int i;
 		int values[reset_gpios->ndescs];
 
 		for (i = 0; i < reset_gpios->ndescs; i++)
 			values[i] = value;
 
-	gpiod_set_array_value_cansleep(reset_gpios->ndescs, reset_gpios->desc,
-				       values);
+		gpiod_set_array_value_cansleep(
+			reset_gpios->ndescs, reset_gpios->desc, values);
+	}
 }
 
 static void mmc_pwrseq_simple_pre_power_on(struct mmc_host *host)
@@ -79,6 +82,7 @@ static void mmc_pwrseq_simple_free(struct mmc_host *host)
 	struct mmc_pwrseq_simple *pwrseq = container_of(host->pwrseq,
 					struct mmc_pwrseq_simple, pwrseq);
 
+	if (!IS_ERR(pwrseq->reset_gpios))
 		gpiod_put_array(pwrseq->reset_gpios);
 
 	if (!IS_ERR(pwrseq->ext_clk))
@@ -112,7 +116,9 @@ struct mmc_pwrseq *mmc_pwrseq_simple_alloc(struct mmc_host *host,
 	}
 
 	pwrseq->reset_gpios = gpiod_get_array(dev, "reset", GPIOD_OUT_HIGH);
-	if (IS_ERR(pwrseq->reset_gpios)) {
+	if (IS_ERR(pwrseq->reset_gpios) &&
+	    PTR_ERR(pwrseq->reset_gpios) != -ENOENT &&
+	    PTR_ERR(pwrseq->reset_gpios) != -ENOSYS) {
 		ret = PTR_ERR(pwrseq->reset_gpios);
 		goto clk_put;
 	}

drivers/mmc/core/sd.c

@@ -329,6 +329,7 @@ static int mmc_read_switch(struct mmc_card *card)
 		card->sw_caps.sd3_bus_mode = status[13];
 		/* Driver Strengths supported by the card */
 		card->sw_caps.sd3_drv_type = status[9];
+		card->sw_caps.sd3_curr_limit = status[7] | status[6] << 8;
 	}
 
 out:
@@ -545,14 +546,25 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status)
 	 * when we set current limit to 200ma, the card will draw 200ma, and
 	 * when we set current limit to 400/600/800ma, the card will draw its
 	 * maximum 300ma from the host.
+	 *
+	 * The above is incorrect: if we try to set a current limit that is
+	 * not supported by the card, the card can rightfully error out the
+	 * attempt, and remain at the default current limit.  This results
+	 * in a 300mA card being limited to 200mA even though the host
+	 * supports 800mA. Failures seen with SanDisk 8GB UHS cards with
+	 * an iMX6 host. --rmk
 	 */
-	if (max_current >= 800)
+	if (max_current >= 800 &&
+	    card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_800)
 		current_limit = SD_SET_CURRENT_LIMIT_800;
-	else if (max_current >= 600)
+	else if (max_current >= 600 &&
+		 card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_600)
 		current_limit = SD_SET_CURRENT_LIMIT_600;
-	else if (max_current >= 400)
+	else if (max_current >= 400 &&
+		 card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_400)
 		current_limit = SD_SET_CURRENT_LIMIT_400;
-	else if (max_current >= 200)
+	else if (max_current >= 200 &&
+		 card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_200)
 		current_limit = SD_SET_CURRENT_LIMIT_200;
 
 	if (current_limit != SD_SET_CURRENT_NO_CHANGE) {
@@ -626,9 +638,9 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
 	 * SDR104 mode SD-cards. Note that tuning is mandatory for SDR104.
 	 */
 	if (!mmc_host_is_spi(card->host) &&
-		(card->sd_bus_speed == UHS_SDR50_BUS_SPEED ||
-		 card->sd_bus_speed == UHS_DDR50_BUS_SPEED ||
-		 card->sd_bus_speed == UHS_SDR104_BUS_SPEED)) {
+		(card->host->ios.timing == MMC_TIMING_UHS_SDR50 ||
+		 card->host->ios.timing == MMC_TIMING_UHS_DDR50 ||
+		 card->host->ios.timing == MMC_TIMING_UHS_SDR104)) {
 		err = mmc_execute_tuning(card);
 
 		/*
@@ -638,7 +650,7 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
 		 * difference between v3.00 and 3.01 spec means that CMD19
 		 * tuning is also available for DDR50 mode.
 		 */
-		if (err && card->sd_bus_speed == UHS_DDR50_BUS_SPEED) {
+		if (err && card->host->ios.timing == MMC_TIMING_UHS_DDR50) {
 			pr_warn("%s: ddr50 tuning failed\n",
 				mmc_hostname(card->host));
 			err = 0;

drivers/mmc/core/sdio.c

@@ -535,8 +535,8 @@ static int mmc_sdio_init_uhs_card(struct mmc_card *card)
 	 * SDR104 mode SD-cards. Note that tuning is mandatory for SDR104.
 	 */
 	if (!mmc_host_is_spi(card->host) &&
-	    ((card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR50) ||
-	     (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR104)))
+	    ((card->host->ios.timing == MMC_TIMING_UHS_SDR50) ||
+	      (card->host->ios.timing == MMC_TIMING_UHS_SDR104)))
 		err = mmc_execute_tuning(card);
 out:
 	return err;

drivers/mmc/core/sdio_cis.c

@@ -223,6 +223,7 @@ static const struct cis_tpl cis_tpl_list[] = {
 	{	0x20,	4,	cistpl_manfid		},
 	{	0x21,	2,	/* cistpl_funcid */	},
 	{	0x22,	0,	cistpl_funce		},
+	{	0x91,	2,	/* cistpl_sdio_std */	},
 };
 
 static int sdio_read_cis(struct mmc_card *card, struct sdio_func *func)

drivers/mmc/host/mmci.c

@@ -151,6 +151,7 @@ static struct variant_data variant_nomadik = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
 	.clkreg			= MCI_CLK_ENABLE,
+	.clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
 	.datalength_bits	= 24,
 	.datactrl_mask_sdio	= MCI_ST_DPSM_SDIOEN,
 	.st_sdio		= true,
@@ -1886,7 +1887,7 @@ static struct amba_id mmci_ids[] = {
 	{
 		.id     = 0x00280180,
 		.mask   = 0x00ffffff,
-		.data	= &variant_u300,
+		.data	= &variant_nomadik,
 	},
 	{
 		.id     = 0x00480180,

drivers/mmc/host/tmio_mmc_dma.c

@@ -94,9 +94,9 @@ static void tmio_mmc_start_dma_rx(struct tmio_mmc_host *host)
 			desc = NULL;
 			ret = cookie;
 		}
-	}
 		dev_dbg(&host->pdev->dev, "%s(): mapped %d -> %d, cookie %d, rq %p\n",
 			__func__, host->sg_len, ret, cookie, host->mrq);
+	}
 
 pio:
 	if (!desc) {
@@ -116,8 +116,8 @@ static void tmio_mmc_start_dma_rx(struct tmio_mmc_host *host)
 			 "DMA failed: %d, falling back to PIO\n", ret);
 	}
 
-	dev_dbg(&host->pdev->dev, "%s(): desc %p, cookie %d, sg[%d]\n", __func__,
-		desc, cookie, host->sg_len);
+	dev_dbg(&host->pdev->dev, "%s(): desc %p, sg[%d]\n", __func__,
+		desc, host->sg_len);
 }
 
 static void tmio_mmc_start_dma_tx(struct tmio_mmc_host *host)
@@ -174,9 +174,9 @@ static void tmio_mmc_start_dma_tx(struct tmio_mmc_host *host)
 			desc = NULL;
 			ret = cookie;
 		}
-	}
 		dev_dbg(&host->pdev->dev, "%s(): mapped %d -> %d, cookie %d, rq %p\n",
 			__func__, host->sg_len, ret, cookie, host->mrq);
+	}
 
 pio:
 	if (!desc) {
@@ -196,8 +196,7 @@ static void tmio_mmc_start_dma_tx(struct tmio_mmc_host *host)
 			 "DMA failed: %d, falling back to PIO\n", ret);
 	}
 
-	dev_dbg(&host->pdev->dev, "%s(): desc %p, cookie %d\n", __func__,
-		desc, cookie);
+	dev_dbg(&host->pdev->dev, "%s(): desc %p\n", __func__, desc);
 }
 
 void tmio_mmc_start_dma(struct tmio_mmc_host *host,