Commit 3265f421 authored by Robert Hancock's avatar Robert Hancock Committed by David S. Miller

net: phy: at803x: add fiber support

Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.

Enable the appropriate interrupt bits to detect fiber-side link up
or down events.

Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: default avatarRobert Hancock <robert.hancock@calian.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 4f3a00c7
......@@ -51,6 +51,8 @@
#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
#define AT803X_INTR_ENABLE_WOL BIT(0)
......@@ -85,7 +87,17 @@
#define AT803X_DEBUG_DATA 0x1E
#define AT803X_MODE_CFG_MASK 0x0F
#define AT803X_MODE_CFG_SGMII 0x01
#define AT803X_MODE_CFG_BASET_RGMII 0x00
#define AT803X_MODE_CFG_BASET_SGMII 0x01
#define AT803X_MODE_CFG_BX1000_RGMII_50OHM 0x02
#define AT803X_MODE_CFG_BX1000_RGMII_75OHM 0x03
#define AT803X_MODE_CFG_BX1000_CONV_50OHM 0x04
#define AT803X_MODE_CFG_BX1000_CONV_75OHM 0x05
#define AT803X_MODE_CFG_FX100_RGMII_50OHM 0x06
#define AT803X_MODE_CFG_FX100_CONV_50OHM 0x07
#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B
#define AT803X_MODE_CFG_FX100_RGMII_75OHM 0x0E
#define AT803X_MODE_CFG_FX100_CONV_75OHM 0x0F
#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/
#define AT803X_PSSR_MR_AN_COMPLETE 0x0200
......@@ -283,6 +295,8 @@ struct at803x_priv {
u16 clk_25m_mask;
u8 smarteee_lpi_tw_1g;
u8 smarteee_lpi_tw_100m;
bool is_fiber;
bool is_1000basex;
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
struct regulator *vddio;
......@@ -784,7 +798,33 @@ static int at803x_probe(struct phy_device *phydev)
return ret;
}
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
int mode_cfg;
if (ccr < 0)
goto err;
mode_cfg = ccr & AT803X_MODE_CFG_MASK;
switch (mode_cfg) {
case AT803X_MODE_CFG_BX1000_RGMII_50OHM:
case AT803X_MODE_CFG_BX1000_RGMII_75OHM:
priv->is_1000basex = true;
fallthrough;
case AT803X_MODE_CFG_FX100_RGMII_50OHM:
case AT803X_MODE_CFG_FX100_RGMII_75OHM:
priv->is_fiber = true;
break;
}
}
return 0;
err:
if (priv->vddio)
regulator_disable(priv->vddio);
return ret;
}
static void at803x_remove(struct phy_device *phydev)
......@@ -797,6 +837,7 @@ static void at803x_remove(struct phy_device *phydev)
static int at803x_get_features(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
int err;
err = genphy_read_abilities(phydev);
......@@ -823,12 +864,13 @@ static int at803x_get_features(struct phy_device *phydev)
* As a result of that, ESTATUS_1000_XFULL is set
* to 1 even when operating in copper TP mode.
*
* Remove this mode from the supported link modes,
* as this driver currently only supports copper
* operation.
* Remove this mode from the supported link modes
* when not operating in 1000BaseX mode.
*/
if (!priv->is_1000basex)
linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
phydev->supported);
return 0;
}
......@@ -892,15 +934,18 @@ static int at8031_pll_config(struct phy_device *phydev)
static int at803x_config_init(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
int ret;
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
/* Some bootloaders leave the fiber page selected.
* Switch to the copper page, as otherwise we read
* the PHY capabilities from the fiber side.
* Switch to the appropriate page (fiber or copper), as otherwise we
* read the PHY capabilities from the wrong page.
*/
phy_lock_mdio_bus(phydev);
ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
ret = at803x_write_page(phydev,
priv->is_fiber ? AT803X_PAGE_FIBER :
AT803X_PAGE_COPPER);
phy_unlock_mdio_bus(phydev);
if (ret)
return ret;
......@@ -959,6 +1004,7 @@ static int at803x_ack_interrupt(struct phy_device *phydev)
static int at803x_config_intr(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
int err;
int value;
......@@ -975,6 +1021,10 @@ static int at803x_config_intr(struct phy_device *phydev)
value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
value |= AT803X_INTR_ENABLE_LINK_FAIL;
value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
if (priv->is_fiber) {
value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
}
err = phy_write(phydev, AT803X_INTR_ENABLE, value);
} else {
......@@ -1107,8 +1157,12 @@ static int at803x_read_specific_status(struct phy_device *phydev)
static int at803x_read_status(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
int err, old_link = phydev->link;
if (priv->is_1000basex)
return genphy_c37_read_status(phydev);
/* Update the link, but return if there was an error */
err = genphy_update_link(phydev);
if (err)
......@@ -1162,6 +1216,7 @@ static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
static int at803x_config_aneg(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
int ret;
ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
......@@ -1178,6 +1233,9 @@ static int at803x_config_aneg(struct phy_device *phydev)
return ret;
}
if (priv->is_1000basex)
return genphy_c37_config_aneg(phydev);
/* Do not restart auto-negotiation by setting ret to 0 defautly,
* when calling __genphy_config_aneg later.
*/
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment