usb: phy: qcom: New APQ8016/MSM8916 USB transceiver driver

Driver handles PHY initialization, clock management, power
management and workarounds required after resetting the hardware.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt

+Qualcomm's APQ8016/MSM8916 USB transceiver controller
+
+- compatible:
+    Usage: required
+    Value type: <string>
+    Definition: Should contain "qcom,usb-8x16-phy".
+
+- reg:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: USB PHY base address and length of the register map
+
+- clocks:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: See clock-bindings.txt section "consumers". List of
+                two clock specifiers for interface and core controller
+                clocks.
+
+- clock-names:
+    Usage: required
+    Value type: <string>
+    Definition: Must contain "iface" and "core" strings.
+
+- vddcx-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator VDCCX supply node.
+
+- v1p8-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator 1.8V supply node.
+
+- v3p3-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator 3.3V supply node.
+
+- resets:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: See reset.txt section "consumers". PHY reset specifier.
+
+- reset-names:
+    Usage: required
+    Value type: <string>
+    Definition: Must contain "phy" string.
+
+- switch-gpio:
+    Usage: optional
+    Value type: <prop-encoded-array>
+    Definition: Some boards are using Dual SPDT USB Switch, witch is
+                controlled by GPIO to de/multiplex D+/D- USB lines
+                between connectors.
+
+Example:
+	usb_phy: phy@78d9000 {
+		compatible = "qcom,usb-8x16-phy";
+		reg = <0x78d9000 0x400>;
+
+		vddcx-supply = <&pm8916_s1_corner>;
+		v1p8-supply = <&pm8916_l7>;
+		v3p3-supply = <&pm8916_l13>;
+
+		clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+			     <&gcc GCC_USB_HS_SYSTEM_CLK>;
+		clock-names = "iface", "core";
+
+		resets = <&gcc GCC_USB2A_PHY_BCR>;
+		reset-names = "phy";
+
+		// D+/D- lines: 1 - Routed to HUB, 0 - Device connector
+		switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
+	};
+

drivers/usb/phy/Kconfig

@@ -152,6 +152,20 @@ config USB_MSM_OTG
 	  This driver is not supported on boards like trout which
 	  has an external PHY.
 
+config USB_QCOM_8X16_PHY
+	tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on RESET_CONTROLLER
+	select USB_PHY
+	select USB_ULPI_VIEWPORT
+	help
+	  Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
+	  It handles PHY initialization, clock management, power management,
+	  and workarounds required after resetting the hardware.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called phy-qcom-8x16-usb.
+
 config USB_MV_OTG
 	tristate "Marvell USB OTG support"
 	depends on USB_EHCI_MV && USB_MV_UDC && PM

drivers/usb/phy/Makefile

@@ -20,6 +20,7 @@ obj-$(CONFIG_USB_EHCI_TEGRA)		+= phy-tegra-usb.o
 obj-$(CONFIG_USB_GPIO_VBUS)		+= phy-gpio-vbus-usb.o
 obj-$(CONFIG_USB_ISP1301)		+= phy-isp1301.o
 obj-$(CONFIG_USB_MSM_OTG)		+= phy-msm-usb.o
+obj-$(CONFIG_USB_QCOM_8X16_PHY)	+= phy-qcom-8x16-usb.o
 obj-$(CONFIG_USB_MV_OTG)		+= phy-mv-usb.o
 obj-$(CONFIG_USB_MXS_PHY)		+= phy-mxs-usb.o
 obj-$(CONFIG_USB_RCAR_PHY)		+= phy-rcar-usb.o