Commit 3535c4c0 authored by Linus Torvalds's avatar Linus Torvalds

Remove obsoleted drivers/char/h8.c drivers/char/h8.h.

parent 1baaf2ab
This diff is collapsed.
/*
*/
#ifndef __H8_H__
#define __H8_H__
/*
* Register address and offsets
*/
#define H8_BASE_ADDR 0x170 /* default */
#define H8_IRQ 9 /* default */
#define H8_STATUS_REG_OFF 0x4
#define H8_CMD_REG_OFF 0x4
#define H8_DATA_REG_OFF 0x0
/* H8 register bit definitions */
/* status register */
#define H8_OFULL 0x1 /* output data register full */
#define H8_IFULL 0x2 /* input data register full */
#define H8_CMD 0x8 /* command / not data */
#define H8_INTR 0xfa
#define H8_NACK 0xfc
#define H8_BYTE_LEVEL_ACK 0xfd
#define H8_CMD_ACK 0xfe
#define H8_SYNC_BYTE 0x99
/*
* H8 command definitions
*/
/* System info commands */
#define H8_SYNC 0x0
#define H8_RD_SN 0x1
#define H8_RD_ENET_ADDR 0x2
#define H8_RD_HW_VER 0x3
#define H8_RD_MIC_VER 0x4
#define H8_RD_MAX_TEMP 0x5
#define H8_RD_MIN_TEMP 0x6
#define H8_RD_CURR_TEMP 0x7
#define H8_RD_SYS_VARIENT 0x8
#define H8_RD_PWR_ON_CYCLES 0x9
#define H8_RD_PWR_ON_SECS 0xa
#define H8_RD_RESET_STATUS 0xb
#define H8_RD_PWR_DN_STATUS 0xc
#define H8_RD_EVENT_STATUS 0xd
#define H8_RD_ROM_CKSM 0xe
#define H8_RD_EXT_STATUS 0xf
#define H8_RD_USER_CFG 0x10
#define H8_RD_INT_BATT_VOLT 0x11
#define H8_RD_DC_INPUT_VOLT 0x12
#define H8_RD_HORIZ_PTR_VOLT 0x13
#define H8_RD_VERT_PTR_VOLT 0x14
#define H8_RD_EEPROM_STATUS 0x15
#define H8_RD_ERR_STATUS 0x16
#define H8_RD_NEW_BUSY_SPEED 0x17
#define H8_RD_CONFIG_INTERFACE 0x18
#define H8_RD_INT_BATT_STATUS 0x19
#define H8_RD_EXT_BATT_STATUS 0x1a
#define H8_RD_PWR_UP_STATUS 0x1b
#define H8_RD_EVENT_STATUS_MASK 0x56
/* Read/write/modify commands */
#define H8_CTL_EMU_BITPORT 0x32
#define H8_DEVICE_CONTROL 0x21
#define H8_CTL_TFT_BRT_DC 0x22
#define H8_CTL_WATCHDOG 0x23
#define H8_CTL_MIC_PROT 0x24
#define H8_CTL_INT_BATT_CHG 0x25
#define H8_CTL_EXT_BATT_CHG 0x26
#define H8_CTL_MARK_SPACE 0x27
#define H8_CTL_MOUSE_SENSITIVITY 0x28
#define H8_CTL_DIAG_MODE 0x29
#define H8_CTL_IDLE_AND_BUSY_SPDS 0x2a
#define H8_CTL_TFT_BRT_BATT 0x2b
#define H8_CTL_UPPER_TEMP 0x2c
#define H8_CTL_LOWER_TEMP 0x2d
#define H8_CTL_TEMP_CUTOUT 0x2e
#define H8_CTL_WAKEUP 0x2f
#define H8_CTL_CHG_THRESHOLD 0x30
#define H8_CTL_TURBO_MODE 0x31
#define H8_SET_DIAG_STATUS 0x40
#define H8_SOFTWARE_RESET 0x41
#define H8_RECAL_PTR 0x42
#define H8_SET_INT_BATT_PERCENT 0x43
#define H8_WRT_CFG_INTERFACE_REG 0x45
#define H8_WRT_EVENT_STATUS_MASK 0x57
#define H8_ENTER_POST_MODE 0x46
#define H8_EXIT_POST_MODE 0x47
/* Block transfer commands */
#define H8_RD_EEPROM 0x50
#define H8_WRT_EEPROM 0x51
#define H8_WRT_TO_STATUS_DISP 0x52
#define H8_DEFINE_SPC_CHAR 0x53
/* Generic commands */
#define H8_DEFINE_TABLE_STRING_ENTRY 0x60
/* Battery control commands */
#define H8_PERFORM_EMU_CMD 0x70
#define H8_EMU_RD_REG 0x71
#define H8_EMU_WRT_REG 0x72
#define H8_EMU_RD_RAM 0x73
#define H8_EMU_WRT_RAM 0x74
#define H8_BQ_RD_REG 0x75
#define H8_BQ_WRT_REG 0x76
/* System admin commands */
#define H8_PWR_OFF 0x80
/*
* H8 command related definitions
*/
/* device control argument bits */
#define H8_ENAB_EXTSMI 0x1
#define H8_DISAB_IRQ 0x2
#define H8_ENAB_FLASH_WRT 0x4
#define H8_ENAB_THERM 0x8
#define H8_ENAB_INT_PTR 0x10
#define H8_ENAB_LOW_SPD_IND 0x20
#define H8_ENAB_EXT_PTR 0x40
#define H8_DISAB_PWR_OFF_SW 0x80
#define H8_POWER_OFF 0x80
/* H8 read event status bits */
#define H8_DC_CHANGE 0x1
#define H8_INT_BATT_LOW 0x2
#define H8_INT_BATT_CHARGE_THRESHOLD 0x4
#define H8_INT_BATT_CHARGE_STATE 0x8
#define H8_INT_BATT_STATUS 0x10
#define H8_EXT_BATT_CHARGE_STATE 0x20
#define H8_EXT_BATT_LOW 0x40
#define H8_EXT_BATT_STATUS 0x80
#define H8_THERMAL_THRESHOLD 0x100
#define H8_WATCHDOG 0x200
#define H8_DOCKING_STATION_STATUS 0x400
#define H8_EXT_MOUSE_OR_CASE_SWITCH 0x800
#define H8_KEYBOARD 0x1000
#define H8_BATT_CHANGE_OVER 0x2000
#define H8_POWER_BUTTON 0x4000
#define H8_SHUTDOWN 0x8000
/* H8 control idle and busy speeds */
#define H8_SPEED_LOW 0x1
#define H8_SPEED_MED 0x2
#define H8_SPEED_HI 0x3
#define H8_SPEED_LOCKED 0x80
#define H8_MAX_CMD_SIZE 18
#define H8_Q_ALLOC_AMOUNT 10
/* H8 state field values */
#define H8_IDLE 1
#define H8_XMIT 2
#define H8_RCV 3
#define H8_RESYNC 4
#define H8_INTR_MODE 5
/* Mask values for control functions */
#define UTH_HYSTERESIS 5
#define DEFAULT_UTHERMAL_THRESHOLD 115
#define H8_TIMEOUT_INTERVAL 30
#define H8_RUN 4
#define H8_GET_MAX_TEMP 0x1
#define H8_GET_CURR_TEMP 0x2
#define H8_GET_UPPR_THRMAL_THOLD 0x4
#define H8_GET_ETHERNET_ADDR 0x8
#define H8_SYNC_OP 0x10
#define H8_SET_UPPR_THRMAL_THOLD 0x20
#define H8_GET_INT_BATT_STAT 0x40
#define H8_GET_CPU_SPD 0x80
#define H8_MANAGE_UTHERM 0x100
#define H8_MANAGE_LTHERM 0x200
#define H8_HALT 0x400
#define H8_CRASH 0x800
#define H8_GET_EXT_STATUS 0x10000
#define H8_MANAGE_QUIET 0x20000
#define H8_MANAGE_SPEEDUP 0x40000
#define H8_MANAGE_BATTERY 0x80000
#define H8_SYSTEM_DELAY_TEST 0x100000
#define H8_POWER_SWITCH_TEST 0x200000
/* CPU speeds and clock divisor values */
#define MHZ_14 5
#define MHZ_28 4
#define MHZ_57 3
#define MHZ_115 2
#define MHZ_230 0
/*
* H8 data
*/
struct h8_data {
u_int ser_num;
u_char ether_add[6];
u_short hw_ver;
u_short mic_ver;
u_short max_tmp;
u_short min_tmp;
u_short cur_tmp;
u_int sys_var;
u_int pow_on;
u_int pow_on_secs;
u_char reset_status;
u_char pwr_dn_status;
u_short event_status;
u_short rom_cksm;
u_short ext_status;
u_short u_cfg;
u_char ibatt_volt;
u_char dc_volt;
u_char ptr_horiz;
u_char ptr_vert;
u_char eeprom_status;
u_char error_status;
u_char new_busy_speed;
u_char cfg_interface;
u_short int_batt_status;
u_short ext_batt_status;
u_char pow_up_status;
u_char event_status_mask;
};
/*
* H8 command buffers
*/
typedef struct h8_cmd_q {
struct list_head link; /* double linked list */
int ncmd; /* number of bytes in command */
int nrsp; /* number of bytes in response */
int cnt; /* number of bytes sent/received */
int nacks; /* number of byte level acks */
u_char cmdbuf[H8_MAX_CMD_SIZE]; /* buffer to store command */
u_char rcvbuf[H8_MAX_CMD_SIZE]; /* buffer to store response */
} h8_cmd_q_t;
union intr_buf {
u_char byte[2];
u_int word;
};
#endif /* __H8_H_ */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment