hwmon: (lm90) Add remaining chips supported by adm1021 driver

All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.

After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.

Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Documentation/hwmon/lm90.rst

@@ -355,6 +355,38 @@ Supported chips:
 
 	       https://www.ti.com/lit/gpn/tmp461
 
+  * Philips NE1617, NE1617A
+
+    Prefix: 'max1617' (probably detected as a max1617)
+
+    Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e
+
+    Datasheets: Publicly available at the Philips website
+
+  * Genesys Logic GL523SM
+
+    Prefix: 'gl523sm'
+
+    Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e
+
+    Datasheet:
+
+  * TI THMC10
+
+    Prefix: 'thmc10'
+
+    Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e
+
+    Datasheet: Publicly available at the TI website
+
+  * Onsemi MC1066
+
+    Prefix: 'mc1066'
+
+    Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e
+
+    Datasheet: Publicly available at the Onsemi website
+
 Author: Jean Delvare <jdelvare@suse.de>
 
 
@@ -385,7 +417,7 @@ features:
 LM84:
   * 8 bit sensor resolution
 
-ADM1021, MAX1617:
+ADM1021, GL523SM, MAX1617, NE1617, NE1617A, THMC10:
   * 8 bit sensor resolution
   * Low temperature limits
 

drivers/hwmon/Kconfig

@@ -100,6 +100,7 @@ config SENSORS_AD7418
 config SENSORS_ADM1021
 	tristate "Analog Devices ADM1021 and compatibles"
 	depends on I2C
+	depends on SENSORS_LM90=n
 	help
 	  If you say yes here you get support for Analog Devices ADM1021
 	  and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A,

drivers/hwmon/lm90.c

@@ -233,6 +233,7 @@ static const struct i2c_device_id lm90_id[] = {
 	{ "adt7482", adt7481 },
 	{ "adt7483a", adt7481 },
 	{ "g781", g781 },
+	{ "gl523sm", max1617 },
 	{ "lm84", lm84 },
 	{ "lm86", lm86 },
 	{ "lm89", lm86 },
@@ -254,9 +255,11 @@ static const struct i2c_device_id lm90_id[] = {
 	{ "max6692", max6648 },
 	{ "max6695", max6696 },
 	{ "max6696", max6696 },
+	{ "mc1066", max1617 },
 	{ "nct1008", adt7461a },
 	{ "w83l771", w83l771 },
 	{ "sa56004", sa56004 },
+	{ "thmc10", max1617 },
 	{ "tmp451", tmp451 },
 	{ "tmp461", tmp461 },
 	{ }
@@ -2127,6 +2130,18 @@ static const char *lm90_detect_gmt(struct i2c_client *client, int chip_id,
 	return NULL;
 }
 
+static const char *lm90_detect_ti49(struct i2c_client *client, bool common_address,
+				    int chip_id, int config1, int convrate)
+{
+	if (common_address && chip_id == 0x00 && !(config1 & 0x3f) && !(convrate & 0xf8)) {
+		/* THMC10: Unsupported registers return 0xff */
+		if (i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_TEMPL) == 0xff &&
+		    i2c_smbus_read_byte_data(client, LM90_REG_REMOTE_CRIT) == 0xff)
+			return "thmc10";
+	}
+	return NULL;
+}
+
 static const char *lm90_detect_ti(struct i2c_client *client, int chip_id,
 				  int config1, int convrate)
 {
@@ -2210,6 +2225,10 @@ static int lm90_detect(struct i2c_client *client, struct i2c_board_info *info)
 	case 0x01:	/* National Semiconductor */
 		name = lm90_detect_national(client, chip_id, config1, convrate);
 		break;
+	case 0x23:	/* Genesys Logic */
+		if (common_address && !(config1 & 0x3f) && !(convrate & 0xf8))
+			name = "gl523sm";
+		break;
 	case 0x41:	/* Analog Devices */
 		name = lm90_detect_analog(client, common_address, chip_id, config1,
 					  convrate);
@@ -2217,10 +2236,17 @@ static int lm90_detect(struct i2c_client *client, struct i2c_board_info *info)
 	case 0x47:	/* GMT */
 		name = lm90_detect_gmt(client, chip_id, config1, convrate);
 		break;
+	case 0x49:	/* TI */
+		name = lm90_detect_ti49(client, common_address, chip_id, config1, convrate);
+		break;
 	case 0x4d:	/* Maxim Integrated */
 		name = lm90_detect_maxim(client, common_address, chip_id,
 					 config1, convrate);
 		break;
+	case 0x54:	/* ON MC1066, Microchip TC1068, TCM1617 (originally TelCom) */
+		if (common_address && !(config1 & 0x3f) && !(convrate & 0xf8))
+			name = "mc1066";
+		break;
 	case 0x55:	/* TI */
 		name = lm90_detect_ti(client, chip_id, config1, convrate);
 		break;