Merge tag 'soc-fixes-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "A couple of platforms have some last-minute fixes, in particular:

   - riscv gets some fixes for noncoherent DMA on the renesas and thead
     platforms and dts fix for SPI on the visionfive 2 board

   - Qualcomm Snapdragon gets three dts fixes to address board specific
     regressions on the pmic and gpio nodes

   - Rockchip platforms get multiple dts fixes to address issues on the
     recent rk3399 platform as well as the older rk3128 platform that
     apparently regressed a while ago.

   - TI OMAP gets some trivial code and dts fixes and a regression fix
     for the omap1 ams-delta modem

   - NXP i.MX firmware has one fix for a use-after-free but in its error
     handling"

* tag 'soc-fixes-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
  soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM
  riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT
  riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT
  riscv: dts: thead: set dma-noncoherent to soc bus
  arm64: dts: rockchip: Fix i2s0 pin conflict on ROCK Pi 4 boards
  arm64: dts: rockchip: Add i2s0-2ch-bus-bclk-off pins to RK3399
  clk: ti: Fix missing omap5 mcbsp functional clock and aliases
  clk: ti: Fix missing omap4 mcbsp functional clock and aliases
  ARM: OMAP1: ams-delta: Fix MODEM initialization failure
  soc: renesas: Make ARCH_R9A07G043 depend on required options
  riscv: dts: starfive: visionfive 2: correct spi's ss pin
  firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels()
  ARM: OMAP: timer32K: fix all kernel-doc warnings
  ARM: omap2: fix a debug printk
  ARM: dts: rockchip: Fix timer clocks for RK3128
  ARM: dts: rockchip: Add missing quirk for RK3128's dma engine
  ARM: dts: rockchip: Add missing arm timer interrupt for RK3128
  ARM: dts: rockchip: Fix i2c0 register address for RK3128
  arm64: dts: rockchip: set codec system-clock-fixed on px30-ringneck-haikou
  arm64: dts: rockchip: use codec as clock master on px30-ringneck-haikou
  ...

MAINTAINERS

@@ -13846,9 +13846,10 @@ F:	Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml
 F:	drivers/staging/media/meson/vdec/
 
 METHODE UDPU SUPPORT
-M:	Vladimir Vid <vladimir.vid@sartura.hr>
+M:	Robert Marko <robert.marko@sartura.hr>
 S:	Maintained
-F:	arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+F:	arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
+F:	arch/arm64/boot/dts/marvell/armada-3720-uDPU.*
 
 MHI BUS
 M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

arch/arm/boot/dts/rockchip/rk3128.dtsi

@@ -64,7 +64,8 @@ timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
 			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		arm,cpu-registers-not-fw-configured;
 		clock-frequency = <24000000>;
 	};
@@ -233,7 +234,7 @@ timer0: timer@20044000 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044000 0x20>;
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER0>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -241,7 +242,7 @@ timer1: timer@20044020 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044020 0x20>;
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER1>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -249,7 +250,7 @@ timer2: timer@20044040 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044040 0x20>;
 		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER2>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -257,7 +258,7 @@ timer3: timer@20044060 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044060 0x20>;
 		interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER3>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -265,7 +266,7 @@ timer4: timer@20044080 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044080 0x20>;
 		interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER4>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -273,7 +274,7 @@ timer5: timer@200440a0 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x200440a0 0x20>;
 		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER5>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -426,7 +427,7 @@ saradc: saradc@2006c000 {
 
 	i2c0: i2c@20072000 {
 		compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
-		reg = <20072000 0x1000>;
+		reg = <0x20072000 0x1000>;
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 		clock-names = "i2c";
 		clocks = <&cru PCLK_I2C0>;
@@ -458,6 +459,7 @@ pdma: dma-controller@20078000 {
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
 		clocks = <&cru ACLK_DMAC>;
 		clock-names = "apb_pclk";
 		#dma-cells = <1>;

arch/arm/boot/dts/ti/omap/omap4-l4-abe.dtsi

@@ -109,6 +109,8 @@ mcbsp1: mcbsp@0 {
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49022000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP1_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -142,6 +144,8 @@ mcbsp2: mcbsp@0 {
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49024000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP2_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -175,6 +179,8 @@ mcbsp3: mcbsp@0 {
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49026000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP3_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;

arch/arm/boot/dts/ti/omap/omap4-l4.dtsi

@@ -2043,6 +2043,8 @@ mcbsp4: mcbsp@0 {
 				compatible = "ti,omap4-mcbsp";
 				reg = <0x0 0xff>; /* L4 Interconnect */
 				reg-names = "mpu";
+				clocks = <&l4_per_clkctrl OMAP4_MCBSP4_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;

arch/arm/boot/dts/ti/omap/omap5-l4-abe.dtsi

@@ -109,6 +109,8 @@ mcbsp1: mcbsp@0 {
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49022000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP1_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -142,6 +144,8 @@ mcbsp2: mcbsp@0 {
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49024000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP2_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -175,6 +179,8 @@ mcbsp3: mcbsp@0 {
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49026000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP3_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;

arch/arm/mach-omap1/board-ams-delta.c

@@ -550,6 +550,7 @@ static struct platform_device *ams_delta_devices[] __initdata = {
 	&ams_delta_nand_device,
 	&ams_delta_lcd_device,
 	&cx20442_codec_device,
+	&modem_nreset_device,
 };
 
 static struct gpiod_lookup_table *ams_delta_gpio_tables[] __initdata = {
@@ -782,26 +783,28 @@ static struct plat_serial8250_port ams_delta_modem_ports[] = {
 	{ },
 };
 
+static int ams_delta_modem_pm_activate(struct device *dev)
+{
+	modem_priv.regulator = regulator_get(dev, "RESET#");
+	if (IS_ERR(modem_priv.regulator))
+		return -EPROBE_DEFER;
+
+	return 0;
+}
+
+static struct dev_pm_domain ams_delta_modem_pm_domain = {
+	.activate	= ams_delta_modem_pm_activate,
+};
+
 static struct platform_device ams_delta_modem_device = {
 	.name	= "serial8250",
 	.id	= PLAT8250_DEV_PLATFORM1,
 	.dev		= {
 		.platform_data = ams_delta_modem_ports,
+		.pm_domain = &ams_delta_modem_pm_domain,
 	},
 };
 
-static int __init modem_nreset_init(void)
-{
-	int err;
-
-	err = platform_device_register(&modem_nreset_device);
-	if (err)
-		pr_err("Couldn't register the modem regulator device\n");
-
-	return err;
-}
-
-
 /*
  * This function expects MODEM IRQ number already assigned to the port.
  * The MODEM device requires its RESET# pin kept high during probe.
@@ -833,37 +836,6 @@ static int __init ams_delta_modem_init(void)
 }
 arch_initcall_sync(ams_delta_modem_init);
 
-static int __init late_init(void)
-{
-	int err;
-
-	err = modem_nreset_init();
-	if (err)
-		return err;
-
-	/*
-	 * Once the modem device is registered, the modem_nreset
-	 * regulator can be requested on behalf of that device.
-	 */
-	modem_priv.regulator = regulator_get(&ams_delta_modem_device.dev,
-			"RESET#");
-	if (IS_ERR(modem_priv.regulator)) {
-		err = PTR_ERR(modem_priv.regulator);
-		goto unregister;
-	}
-	return 0;
-
-unregister:
-	platform_device_unregister(&ams_delta_modem_device);
-	return err;
-}
-
-static void __init ams_delta_init_late(void)
-{
-	omap1_init_late();
-	late_init();
-}
-
 static void __init ams_delta_map_io(void)
 {
 	omap1_map_io();
@@ -877,7 +849,7 @@ MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
 	.init_early	= omap1_init_early,
 	.init_irq	= omap1_init_irq,
 	.init_machine	= ams_delta_init,
-	.init_late	= ams_delta_init_late,
+	.init_late	= omap1_init_late,
 	.init_time	= omap1_timer_init,
 	.restart	= omap1_restart,
 MACHINE_END

arch/arm/mach-omap1/timer32k.c

@@ -176,17 +176,18 @@ static u64 notrace omap_32k_read_sched_clock(void)
 	return sync32k_cnt_reg ? readl_relaxed(sync32k_cnt_reg) : 0;
 }
 
+static struct timespec64 persistent_ts;
+static cycles_t cycles;
+static unsigned int persistent_mult, persistent_shift;
+
 /**
  * omap_read_persistent_clock64 -  Return time from a persistent clock.
+ * @ts: &struct timespec64 for the returned time
  *
  * Reads the time from a source which isn't disabled during PM, the
  * 32k sync timer.  Convert the cycles elapsed since last read into
  * nsecs and adds to a monotonically increasing timespec64.
  */
-static struct timespec64 persistent_ts;
-static cycles_t cycles;
-static unsigned int persistent_mult, persistent_shift;
-
 static void omap_read_persistent_clock64(struct timespec64 *ts)
 {
 	unsigned long long nsecs;
@@ -206,10 +207,9 @@ static void omap_read_persistent_clock64(struct timespec64 *ts)
 /**
  * omap_init_clocksource_32k - setup and register counter 32k as a
  * kernel clocksource
- * @pbase: base addr of counter_32k module
- * @size: size of counter_32k to map
+ * @vbase: base addr of counter_32k module
  *
- * Returns 0 upon success or negative error code upon failure.
+ * Returns: %0 upon success or negative error code upon failure.
  *
  */
 static int __init omap_init_clocksource_32k(void __iomem *vbase)

arch/arm/mach-omap2/omap_hwmod.c

@@ -2209,7 +2209,7 @@ int omap_hwmod_parse_module_range(struct omap_hwmod *oh,
 		return err;
 
 	pr_debug("omap_hwmod: %s %pOFn at %pR\n",
-		 oh->name, np, &res);
+		 oh->name, np, res);
 
 	if (oh && oh->mpu_rt_idx) {
 		omap_hwmod_fix_mpu_rt_idx(oh, np, res);

arch/arm64/boot/dts/qcom/apq8096-db820c.dts

@@ -62,17 +62,6 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	clocks {
-		divclk4: divclk4 {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-			clock-output-names = "divclk4";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&divclk4_pin_a>;
-		};
-
 	div1_mclk: divclk1 {
 		compatible = "gpio-gate-clock";
 		pinctrl-0 = <&audio_mclk>;
@@ -81,6 +70,15 @@ div1_mclk: divclk1 {
 		#clock-cells = <0>;
 		enable-gpios = <&pm8994_gpios 15 0>;
 	};
+
+	divclk4: divclk4 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "divclk4";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&divclk4_pin_a>;
 	};
 
 	gpio-keys {

arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi

@@ -11,7 +11,6 @@
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
-	clocks {
 	divclk1_cdc: divclk1 {
 		compatible = "gpio-gate-clock";
 		clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
@@ -31,7 +30,6 @@ divclk4: divclk4 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&divclk4_pin_a>;
 	};
-	};
 
 	gpio-keys {
 		compatible = "gpio-keys";

arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts

@@ -20,7 +20,6 @@ / {
 	qcom,pmic-id = <0x20009 0x2000a 0x00 0x00>;
 	qcom,board-id = <31 0>;
 
-	clocks {
 	divclk2_haptics: divclk2 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -30,7 +29,6 @@ divclk2_haptics: divclk2 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&divclk2_pin_a>;
 	};
-	};
 };
 
 &adsp_pil {

arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi

@@ -173,7 +173,7 @@ pmm8654au_1_gpios: gpio@8800 {
 			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
 			reg = <0x8800>;
 			gpio-controller;
-			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
+			gpio-ranges = <&pmm8654au_1_gpios 0 0 12>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;

arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts

@@ -68,15 +68,17 @@ i2s0-sound {
 		simple-audio-card,format = "i2s";
 		simple-audio-card,name = "Haikou,I2S-codec";
 		simple-audio-card,mclk-fs = <512>;
+		simple-audio-card,frame-master = <&sgtl5000_codec>;
+		simple-audio-card,bitclock-master = <&sgtl5000_codec>;
 
-		simple-audio-card,codec {
-			clocks = <&sgtl5000_clk>;
+		sgtl5000_codec: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
+			// Prevent the dai subsystem from overwriting the clock
+			// frequency. We are using a fixed-frequency oscillator.
+			system-clock-fixed;
 		};
 
 		simple-audio-card,cpu {
-			bitclock-master;
-			frame-master;
 			sound-dai = <&i2s0_8ch>;
 		};
 	};

arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi

@@ -492,6 +492,7 @@ &i2c4 {
 
 &i2s0 {
 	pinctrl-0 = <&i2s0_2ch_bus>;
+	pinctrl-1 = <&i2s0_2ch_bus_bclk_off>;
 	rockchip,capture-channels = <2>;
 	rockchip,playback-channels = <2>;
 	status = "okay";

arch/arm64/boot/dts/rockchip/rk3399.dtsi

@@ -2457,6 +2457,16 @@ i2s0_2ch_bus: i2s0-2ch-bus {
 					<4 RK_PA0 1 &pcfg_pull_none>;
 			};
 
+			i2s0_2ch_bus_bclk_off: i2s0-2ch-bus-bclk-off {
+				rockchip,pins =
+					<3 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>,
+					<3 RK_PD1 1 &pcfg_pull_none>,
+					<3 RK_PD2 1 &pcfg_pull_none>,
+					<3 RK_PD3 1 &pcfg_pull_none>,
+					<3 RK_PD7 1 &pcfg_pull_none>,
+					<4 RK_PA0 1 &pcfg_pull_none>;
+			};
+
 			i2s0_8ch_bus: i2s0-8ch-bus {
 				rockchip,pins =
 					<3 RK_PD0 1 &pcfg_pull_none>,

arch/riscv/Kconfig

@@ -273,11 +273,9 @@ config RISCV_DMA_NONCOHERENT
 	select ARCH_HAS_SYNC_DMA_FOR_CPU
 	select ARCH_HAS_SYNC_DMA_FOR_DEVICE
 	select DMA_BOUNCE_UNALIGNED_KMALLOC if SWIOTLB
-	select DMA_DIRECT_REMAP if MMU
 
 config RISCV_NONSTANDARD_CACHE_OPS
 	bool
-	depends on RISCV_DMA_NONCOHERENT
 	help
 	  This enables function pointer support for non-standard noncoherent
 	  systems to handle cache management.
@@ -550,6 +548,7 @@ config RISCV_ISA_ZICBOM
 	depends on RISCV_ALTERNATIVE
 	default y
 	select RISCV_DMA_NONCOHERENT
+	select DMA_DIRECT_REMAP
 	help
 	   Adds support to dynamically detect the presence of the ZICBOM
 	   extension (Cache Block Management Operations) and enable its

arch/riscv/Kconfig.errata

@@ -77,6 +77,7 @@ config ERRATA_THEAD_PBMT
 config ERRATA_THEAD_CMO
 	bool "Apply T-Head cache management errata"
 	depends on ERRATA_THEAD && MMU
+	select DMA_DIRECT_REMAP
 	select RISCV_DMA_NONCOHERENT
 	default y
 	help

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi

@@ -431,7 +431,7 @@ GPOEN_ENABLE,
 		};
 
 		ss-pins {
-			pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_FSS,
+			pinmux = <GPIOMUX(49, GPOUT_SYS_SPI0_FSS,
 					      GPOEN_ENABLE,
 					      GPI_SYS_SPI0_FSS)>;
 			bias-disable;

arch/riscv/boot/dts/thead/th1520.dtsi

@@ -139,6 +139,7 @@ soc {
 		interrupt-parent = <&plic>;
 		#address-cells = <2>;
 		#size-cells = <2>;
+		dma-noncoherent;
 		ranges;
 
 		plic: interrupt-controller@ffd8000000 {

drivers/cache/Kconfig

@@ -3,7 +3,7 @@ menu "Cache Drivers"
 
 config AX45MP_L2_CACHE
 	bool "Andes Technology AX45MP L2 Cache controller"
-	depends on RISCV_DMA_NONCOHERENT
+	depends on RISCV
 	select RISCV_NONSTANDARD_CACHE_OPS
 	help
 	  Support for the L2 cache controller on Andes Technology AX45MP platforms.

drivers/clk/ti/clk-44xx.c

@@ -749,9 +749,14 @@ static struct ti_dt_clk omap44xx_clks[] = {
 	DT_CLK(NULL, "mcbsp1_sync_mux_ck", "abe-clkctrl:0028:26"),
 	DT_CLK(NULL, "mcbsp2_sync_mux_ck", "abe-clkctrl:0030:26"),
 	DT_CLK(NULL, "mcbsp3_sync_mux_ck", "abe-clkctrl:0038:26"),
+	DT_CLK("40122000.mcbsp", "prcm_fck", "abe-clkctrl:0028:26"),
+	DT_CLK("40124000.mcbsp", "prcm_fck", "abe-clkctrl:0030:26"),
+	DT_CLK("40126000.mcbsp", "prcm_fck", "abe-clkctrl:0038:26"),
 	DT_CLK(NULL, "mcbsp4_sync_mux_ck", "l4-per-clkctrl:00c0:26"),
+	DT_CLK("48096000.mcbsp", "prcm_fck", "l4-per-clkctrl:00c0:26"),
 	DT_CLK(NULL, "ocp2scp_usb_phy_phy_48m", "l3-init-clkctrl:00c0:8"),
 	DT_CLK(NULL, "otg_60m_gfclk", "l3-init-clkctrl:0040:24"),
+	DT_CLK(NULL, "pad_fck", "pad_clks_ck"),
 	DT_CLK(NULL, "per_mcbsp4_gfclk", "l4-per-clkctrl:00c0:24"),
 	DT_CLK(NULL, "pmd_stm_clock_mux_ck", "emu-sys-clkctrl:0000:20"),
 	DT_CLK(NULL, "pmd_trace_clk_mux_ck", "emu-sys-clkctrl:0000:22"),

drivers/clk/ti/clk-54xx.c

@@ -565,15 +565,19 @@ static struct ti_dt_clk omap54xx_clks[] = {
 	DT_CLK(NULL, "gpio8_dbclk", "l4per-clkctrl:00f8:8"),
 	DT_CLK(NULL, "mcbsp1_gfclk", "abe-clkctrl:0028:24"),
 	DT_CLK(NULL, "mcbsp1_sync_mux_ck", "abe-clkctrl:0028:26"),
+	DT_CLK("40122000.mcbsp", "prcm_fck", "abe-clkctrl:0028:26"),
 	DT_CLK(NULL, "mcbsp2_gfclk", "abe-clkctrl:0030:24"),
 	DT_CLK(NULL, "mcbsp2_sync_mux_ck", "abe-clkctrl:0030:26"),
+	DT_CLK("40124000.mcbsp", "prcm_fck", "abe-clkctrl:0030:26"),
 	DT_CLK(NULL, "mcbsp3_gfclk", "abe-clkctrl:0038:24"),
 	DT_CLK(NULL, "mcbsp3_sync_mux_ck", "abe-clkctrl:0038:26"),
+	DT_CLK("40126000.mcbsp", "prcm_fck", "abe-clkctrl:0038:26"),
 	DT_CLK(NULL, "mmc1_32khz_clk", "l3init-clkctrl:0008:8"),
 	DT_CLK(NULL, "mmc1_fclk", "l3init-clkctrl:0008:25"),
 	DT_CLK(NULL, "mmc1_fclk_mux", "l3init-clkctrl:0008:24"),
 	DT_CLK(NULL, "mmc2_fclk", "l3init-clkctrl:0010:25"),
 	DT_CLK(NULL, "mmc2_fclk_mux", "l3init-clkctrl:0010:24"),
+	DT_CLK(NULL, "pad_fck", "pad_clks_ck"),
 	DT_CLK(NULL, "sata_ref_clk", "l3init-clkctrl:0068:8"),
 	DT_CLK(NULL, "timer10_gfclk_mux", "l4per-clkctrl:0008:24"),
 	DT_CLK(NULL, "timer11_gfclk_mux", "l4per-clkctrl:0010:24"),

drivers/firmware/imx/imx-dsp.c

@@ -114,11 +114,11 @@ static int imx_dsp_setup_channels(struct imx_dsp_ipc *dsp_ipc)
 		dsp_chan->idx = i % 2;
 		dsp_chan->ch = mbox_request_channel_byname(cl, chan_name);
 		if (IS_ERR(dsp_chan->ch)) {
-			kfree(dsp_chan->name);
 			ret = PTR_ERR(dsp_chan->ch);
 			if (ret != -EPROBE_DEFER)
 				dev_err(dev, "Failed to request mbox chan %s ret %d\n",
 					chan_name, ret);
+			kfree(dsp_chan->name);
 			goto out;
 		}
 

drivers/soc/renesas/Kconfig

@@ -334,12 +334,14 @@ if RISCV
 config ARCH_R9A07G043
 	bool "RISC-V Platform support for RZ/Five"
 	depends on NONPORTABLE
+	depends on RISCV_ALTERNATIVE
+	depends on !RISCV_ISA_ZICBOM
+	depends on RISCV_SBI
 	select ARCH_RZG2L
-	select AX45MP_L2_CACHE if RISCV_DMA_NONCOHERENT
+	select AX45MP_L2_CACHE
 	select DMA_GLOBAL_POOL
-	select ERRATA_ANDES if RISCV_SBI
-	select ERRATA_ANDES_CMO if ERRATA_ANDES
-
+	select ERRATA_ANDES
+	select ERRATA_ANDES_CMO
 	help
 	  This enables support for the Renesas RZ/Five SoC.