Commit 3acf4b5c authored by Francois Romieu's avatar Francois Romieu

uli526x: stop using net_device.{base_addr, irq} and convert to __iomem.

The bulk of the patch comes from the __iomem changes.

- the phy read and write operations were carrying the chip id deep
  down the call chain. Let's waste a pointer and contain the flying
  spaghetti monster.
- phy_{read, write}_1bit only need to access the DCR9 register. The loss
  of generality here should not hurt.
- removed a leftover printk of the EISA era. This is a pure PCI device.
Signed-off-by: default avatarFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: default avatarGrant Grundler <grundler@parisc-linux.org>
parent 5e3cc4e3
......@@ -42,6 +42,8 @@
#include <asm/dma.h>
#include <asm/uaccess.h>
#define uw32(reg, val) iowrite32(val, ioaddr + (reg))
#define ur32(reg) ioread32(ioaddr + (reg))
/* Board/System/Debug information/definition ---------------- */
#define PCI_ULI5261_ID 0x526110B9 /* ULi M5261 ID*/
......@@ -110,14 +112,6 @@ do { \
#define SROM_V41_CODE 0x14
#define SROM_CLK_WRITE(data, ioaddr) \
outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \
udelay(5); \
outl(data|CR9_SROM_READ|CR9_SRCS|CR9_SRCLK,ioaddr); \
udelay(5); \
outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \
udelay(5);
/* Structure/enum declaration ------------------------------- */
struct tx_desc {
__le32 tdes0, tdes1, tdes2, tdes3; /* Data for the card */
......@@ -132,12 +126,15 @@ struct rx_desc {
} __attribute__(( aligned(32) ));
struct uli526x_board_info {
u32 chip_id; /* Chip vendor/Device ID */
struct uli_phy_ops {
void (*write)(struct uli526x_board_info *, u8, u8, u16);
u16 (*read)(struct uli526x_board_info *, u8, u8);
} phy;
struct net_device *next_dev; /* next device */
struct pci_dev *pdev; /* PCI device */
spinlock_t lock;
long ioaddr; /* I/O base address */
void __iomem *ioaddr; /* I/O base address */
u32 cr0_data;
u32 cr5_data;
u32 cr6_data;
......@@ -227,21 +224,21 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *,
static int uli526x_stop(struct net_device *);
static void uli526x_set_filter_mode(struct net_device *);
static const struct ethtool_ops netdev_ethtool_ops;
static u16 read_srom_word(long, int);
static u16 read_srom_word(struct uli526x_board_info *, int);
static irqreturn_t uli526x_interrupt(int, void *);
#ifdef CONFIG_NET_POLL_CONTROLLER
static void uli526x_poll(struct net_device *dev);
#endif
static void uli526x_descriptor_init(struct net_device *, unsigned long);
static void uli526x_descriptor_init(struct net_device *, void __iomem *);
static void allocate_rx_buffer(struct net_device *);
static void update_cr6(u32, unsigned long);
static void update_cr6(u32, void __iomem *);
static void send_filter_frame(struct net_device *, int);
static u16 phy_read(unsigned long, u8, u8, u32);
static u16 phy_readby_cr10(unsigned long, u8, u8);
static void phy_write(unsigned long, u8, u8, u16, u32);
static void phy_writeby_cr10(unsigned long, u8, u8, u16);
static void phy_write_1bit(unsigned long, u32, u32);
static u16 phy_read_1bit(unsigned long, u32);
static u16 phy_readby_cr9(struct uli526x_board_info *, u8, u8);
static u16 phy_readby_cr10(struct uli526x_board_info *, u8, u8);
static void phy_writeby_cr9(struct uli526x_board_info *, u8, u8, u16);
static void phy_writeby_cr10(struct uli526x_board_info *, u8, u8, u16);
static void phy_write_1bit(struct uli526x_board_info *db, u32);
static u16 phy_read_1bit(struct uli526x_board_info *db);
static u8 uli526x_sense_speed(struct uli526x_board_info *);
static void uli526x_process_mode(struct uli526x_board_info *);
static void uli526x_timer(unsigned long);
......@@ -253,6 +250,18 @@ static void uli526x_free_rxbuffer(struct uli526x_board_info *);
static void uli526x_init(struct net_device *);
static void uli526x_set_phyxcer(struct uli526x_board_info *);
static void srom_clk_write(struct uli526x_board_info *db, u32 data)
{
void __iomem *ioaddr = db->ioaddr;
uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS);
udelay(5);
uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS | CR9_SRCLK);
udelay(5);
uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS);
udelay(5);
}
/* ULI526X network board routine ---------------------------- */
static const struct net_device_ops netdev_ops = {
......@@ -277,6 +286,7 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev,
{
struct uli526x_board_info *db; /* board information structure */
struct net_device *dev;
void __iomem *ioaddr;
int i, err;
ULI526X_DBUG(0, "uli526x_init_one()", 0);
......@@ -338,14 +348,26 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev,
db->buf_pool_start = db->buf_pool_ptr;
db->buf_pool_dma_start = db->buf_pool_dma_ptr;
db->chip_id = ent->driver_data;
db->ioaddr = pci_resource_start(pdev, 0);
switch (ent->driver_data) {
case PCI_ULI5263_ID:
db->phy.write = phy_writeby_cr10;
db->phy.read = phy_readby_cr10;
break;
default:
db->phy.write = phy_writeby_cr9;
db->phy.read = phy_readby_cr9;
break;
}
/* IO region. */
ioaddr = pci_iomap(pdev, 0, 0);
if (!ioaddr)
goto err_out_free_tx_buf;
db->ioaddr = ioaddr;
db->pdev = pdev;
db->init = 1;
dev->base_addr = db->ioaddr;
dev->irq = pdev->irq;
pci_set_drvdata(pdev, dev);
/* Register some necessary functions */
......@@ -357,24 +379,24 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev,
/* read 64 word srom data */
for (i = 0; i < 64; i++)
((__le16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db->ioaddr, i));
((__le16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db, i));
/* Set Node address */
if(((u16 *) db->srom)[0] == 0xffff || ((u16 *) db->srom)[0] == 0) /* SROM absent, so read MAC address from ID Table */
{
outl(0x10000, db->ioaddr + DCR0); //Diagnosis mode
outl(0x1c0, db->ioaddr + DCR13); //Reset dianostic pointer port
outl(0, db->ioaddr + DCR14); //Clear reset port
outl(0x10, db->ioaddr + DCR14); //Reset ID Table pointer
outl(0, db->ioaddr + DCR14); //Clear reset port
outl(0, db->ioaddr + DCR13); //Clear CR13
outl(0x1b0, db->ioaddr + DCR13); //Select ID Table access port
uw32(DCR0, 0x10000); //Diagnosis mode
uw32(DCR13, 0x1c0); //Reset dianostic pointer port
uw32(DCR14, 0); //Clear reset port
uw32(DCR14, 0x10); //Reset ID Table pointer
uw32(DCR14, 0); //Clear reset port
uw32(DCR13, 0); //Clear CR13
uw32(DCR13, 0x1b0); //Select ID Table access port
//Read MAC address from CR14
for (i = 0; i < 6; i++)
dev->dev_addr[i] = inl(db->ioaddr + DCR14);
dev->dev_addr[i] = ur32(DCR14);
//Read end
outl(0, db->ioaddr + DCR13); //Clear CR13
outl(0, db->ioaddr + DCR0); //Clear CR0
uw32(DCR13, 0); //Clear CR13
uw32(DCR0, 0); //Clear CR0
udelay(10);
}
else /*Exist SROM*/
......@@ -384,16 +406,18 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev,
}
err = register_netdev (dev);
if (err)
goto err_out_free_tx_buf;
goto err_out_unmap;
netdev_info(dev, "ULi M%04lx at pci%s, %pM, irq %d\n",
ent->driver_data >> 16, pci_name(pdev),
dev->dev_addr, dev->irq);
dev->dev_addr, pdev->irq);
pci_set_master(pdev);
return 0;
err_out_unmap:
pci_iounmap(pdev, db->ioaddr);
err_out_free_tx_buf:
pci_free_consistent(pdev, TX_BUF_ALLOC * TX_DESC_CNT + 4,
db->buf_pool_ptr, db->buf_pool_dma_ptr);
......@@ -418,6 +442,7 @@ static void __devexit uli526x_remove_one (struct pci_dev *pdev)
struct uli526x_board_info *db = netdev_priv(dev);
unregister_netdev(dev);
pci_iounmap(pdev, db->ioaddr);
pci_free_consistent(db->pdev, sizeof(struct tx_desc) *
DESC_ALL_CNT + 0x20, db->desc_pool_ptr,
db->desc_pool_dma_ptr);
......@@ -460,7 +485,8 @@ static int uli526x_open(struct net_device *dev)
/* Initialize ULI526X board */
uli526x_init(dev);
ret = request_irq(dev->irq, uli526x_interrupt, IRQF_SHARED, dev->name, dev);
ret = request_irq(db->pdev->irq, uli526x_interrupt, IRQF_SHARED,
dev->name, dev);
if (ret)
return ret;
......@@ -488,57 +514,57 @@ static int uli526x_open(struct net_device *dev)
static void uli526x_init(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
unsigned long ioaddr = db->ioaddr;
struct uli_phy_ops *phy = &db->phy;
void __iomem *ioaddr = db->ioaddr;
u8 phy_tmp;
u8 timeout;
u16 phy_value;
u16 phy_reg_reset;
ULI526X_DBUG(0, "uli526x_init()", 0);
/* Reset M526x MAC controller */
outl(ULI526X_RESET, ioaddr + DCR0); /* RESET MAC */
uw32(DCR0, ULI526X_RESET); /* RESET MAC */
udelay(100);
outl(db->cr0_data, ioaddr + DCR0);
uw32(DCR0, db->cr0_data);
udelay(5);
/* Phy addr : In some boards,M5261/M5263 phy address != 1 */
db->phy_addr = 1;
for(phy_tmp=0;phy_tmp<32;phy_tmp++)
{
phy_value=phy_read(db->ioaddr,phy_tmp,3,db->chip_id);//peer add
if(phy_value != 0xffff&&phy_value!=0)
{
for (phy_tmp = 0; phy_tmp < 32; phy_tmp++) {
u16 phy_value;
phy_value = phy->read(db, phy_tmp, 3); //peer add
if (phy_value != 0xffff && phy_value != 0) {
db->phy_addr = phy_tmp;
break;
}
}
if(phy_tmp == 32)
if (phy_tmp == 32)
pr_warn("Can not find the phy address!!!\n");
/* Parser SROM and media mode */
db->media_mode = uli526x_media_mode;
/* phyxcer capability setting */
phy_reg_reset = phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id);
phy_reg_reset = phy->read(db, db->phy_addr, 0);
phy_reg_reset = (phy_reg_reset | 0x8000);
phy_write(db->ioaddr, db->phy_addr, 0, phy_reg_reset, db->chip_id);
phy->write(db, db->phy_addr, 0, phy_reg_reset);
/* See IEEE 802.3-2002.pdf (Section 2, Chapter "22.2.4 Management
* functions") or phy data sheet for details on phy reset
*/
udelay(500);
timeout = 10;
while (timeout-- &&
phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id) & 0x8000)
udelay(100);
while (timeout-- && phy->read(db, db->phy_addr, 0) & 0x8000)
udelay(100);
/* Process Phyxcer Media Mode */
uli526x_set_phyxcer(db);
/* Media Mode Process */
if ( !(db->media_mode & ULI526X_AUTO) )
db->op_mode = db->media_mode; /* Force Mode */
db->op_mode = db->media_mode; /* Force Mode */
/* Initialize Transmit/Receive decriptor and CR3/4 */
uli526x_descriptor_init(dev, ioaddr);
......@@ -551,10 +577,10 @@ static void uli526x_init(struct net_device *dev)
/* Init CR7, interrupt active bit */
db->cr7_data = CR7_DEFAULT;
outl(db->cr7_data, ioaddr + DCR7);
uw32(DCR7, db->cr7_data);
/* Init CR15, Tx jabber and Rx watchdog timer */
outl(db->cr15_data, ioaddr + DCR15);
uw32(DCR15, db->cr15_data);
/* Enable ULI526X Tx/Rx function */
db->cr6_data |= CR6_RXSC | CR6_TXSC;
......@@ -571,6 +597,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb,
struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
void __iomem *ioaddr = db->ioaddr;
struct tx_desc *txptr;
unsigned long flags;
......@@ -596,7 +623,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb,
}
/* Disable NIC interrupt */
outl(0, dev->base_addr + DCR7);
uw32(DCR7, 0);
/* transmit this packet */
txptr = db->tx_insert_ptr;
......@@ -607,10 +634,10 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb,
db->tx_insert_ptr = txptr->next_tx_desc;
/* Transmit Packet Process */
if ( (db->tx_packet_cnt < TX_DESC_CNT) ) {
if (db->tx_packet_cnt < TX_DESC_CNT) {
txptr->tdes0 = cpu_to_le32(0x80000000); /* Set owner bit */
db->tx_packet_cnt++; /* Ready to send */
outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */
uw32(DCR1, 0x1); /* Issue Tx polling */
dev->trans_start = jiffies; /* saved time stamp */
}
......@@ -620,7 +647,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb,
/* Restore CR7 to enable interrupt */
spin_unlock_irqrestore(&db->lock, flags);
outl(db->cr7_data, dev->base_addr + DCR7);
uw32(DCR7, db->cr7_data);
/* free this SKB */
dev_kfree_skb(skb);
......@@ -637,9 +664,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb,
static int uli526x_stop(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
unsigned long ioaddr = dev->base_addr;
ULI526X_DBUG(0, "uli526x_stop", 0);
void __iomem *ioaddr = db->ioaddr;
/* disable system */
netif_stop_queue(dev);
......@@ -648,12 +673,12 @@ static int uli526x_stop(struct net_device *dev)
del_timer_sync(&db->timer);
/* Reset & stop ULI526X board */
outl(ULI526X_RESET, ioaddr + DCR0);
uw32(DCR0, ULI526X_RESET);
udelay(5);
phy_write(db->ioaddr, db->phy_addr, 0, 0x8000, db->chip_id);
db->phy.write(db, db->phy_addr, 0, 0x8000);
/* free interrupt */
free_irq(dev->irq, dev);
free_irq(db->pdev->irq, dev);
/* free allocated rx buffer */
uli526x_free_rxbuffer(db);
......@@ -671,18 +696,18 @@ static irqreturn_t uli526x_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
struct uli526x_board_info *db = netdev_priv(dev);
unsigned long ioaddr = dev->base_addr;
void __iomem *ioaddr = db->ioaddr;
unsigned long flags;
spin_lock_irqsave(&db->lock, flags);
outl(0, ioaddr + DCR7);
uw32(DCR7, 0);
/* Got ULI526X status */
db->cr5_data = inl(ioaddr + DCR5);
outl(db->cr5_data, ioaddr + DCR5);
db->cr5_data = ur32(DCR5);
uw32(DCR5, db->cr5_data);
if ( !(db->cr5_data & 0x180c1) ) {
/* Restore CR7 to enable interrupt mask */
outl(db->cr7_data, ioaddr + DCR7);
uw32(DCR7, db->cr7_data);
spin_unlock_irqrestore(&db->lock, flags);
return IRQ_HANDLED;
}
......@@ -710,7 +735,7 @@ static irqreturn_t uli526x_interrupt(int irq, void *dev_id)
uli526x_free_tx_pkt(dev, db);
/* Restore CR7 to enable interrupt mask */
outl(db->cr7_data, ioaddr + DCR7);
uw32(DCR7, db->cr7_data);
spin_unlock_irqrestore(&db->lock, flags);
return IRQ_HANDLED;
......@@ -719,8 +744,10 @@ static irqreturn_t uli526x_interrupt(int irq, void *dev_id)
#ifdef CONFIG_NET_POLL_CONTROLLER
static void uli526x_poll(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
/* ISR grabs the irqsave lock, so this should be safe */
uli526x_interrupt(dev->irq, dev);
uli526x_interrupt(db->pdev->irq, dev);
}
#endif
......@@ -954,12 +981,7 @@ static void netdev_get_drvinfo(struct net_device *dev,
strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
strlcpy(info->version, DRV_VERSION, sizeof(info->version));
if (np->pdev)
strlcpy(info->bus_info, pci_name(np->pdev),
sizeof(info->bus_info));
else
sprintf(info->bus_info, "EISA 0x%lx %d",
dev->base_addr, dev->irq);
strlcpy(info->bus_info, pci_name(np->pdev), sizeof(info->bus_info));
}
static int netdev_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) {
......@@ -999,18 +1021,20 @@ static const struct ethtool_ops netdev_ethtool_ops = {
static void uli526x_timer(unsigned long data)
{
u32 tmp_cr8;
unsigned char tmp_cr12=0;
struct net_device *dev = (struct net_device *) data;
struct uli526x_board_info *db = netdev_priv(dev);
struct uli_phy_ops *phy = &db->phy;
void __iomem *ioaddr = db->ioaddr;
unsigned long flags;
u8 tmp_cr12 = 0;
u32 tmp_cr8;
//ULI526X_DBUG(0, "uli526x_timer()", 0);
spin_lock_irqsave(&db->lock, flags);
/* Dynamic reset ULI526X : system error or transmit time-out */
tmp_cr8 = inl(db->ioaddr + DCR8);
tmp_cr8 = ur32(DCR8);
if ( (db->interval_rx_cnt==0) && (tmp_cr8) ) {
db->reset_cr8++;
db->wait_reset = 1;
......@@ -1020,7 +1044,7 @@ static void uli526x_timer(unsigned long data)
/* TX polling kick monitor */
if ( db->tx_packet_cnt &&
time_after(jiffies, dev_trans_start(dev) + ULI526X_TX_KICK) ) {
outl(0x1, dev->base_addr + DCR1); // Tx polling again
uw32(DCR1, 0x1); // Tx polling again
// TX Timeout
if ( time_after(jiffies, dev_trans_start(dev) + ULI526X_TX_TIMEOUT) ) {
......@@ -1041,7 +1065,7 @@ static void uli526x_timer(unsigned long data)
}
/* Link status check, Dynamic media type change */
if((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)!=0)
if ((phy->read(db, db->phy_addr, 5) & 0x01e0)!=0)
tmp_cr12 = 3;
if ( !(tmp_cr12 & 0x3) && !db->link_failed ) {
......@@ -1054,7 +1078,7 @@ static void uli526x_timer(unsigned long data)
/* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */
/* AUTO don't need */
if ( !(db->media_mode & 0x8) )
phy_write(db->ioaddr, db->phy_addr, 0, 0x1000, db->chip_id);
phy->write(db, db->phy_addr, 0, 0x1000);
/* AUTO mode, if INT phyxcer link failed, select EXT device */
if (db->media_mode & ULI526X_AUTO) {
......@@ -1111,12 +1135,13 @@ static void uli526x_timer(unsigned long data)
static void uli526x_reset_prepare(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
void __iomem *ioaddr = db->ioaddr;
/* Sopt MAC controller */
db->cr6_data &= ~(CR6_RXSC | CR6_TXSC); /* Disable Tx/Rx */
update_cr6(db->cr6_data, dev->base_addr);
outl(0, dev->base_addr + DCR7); /* Disable Interrupt */
outl(inl(dev->base_addr + DCR5), dev->base_addr + DCR5);
update_cr6(db->cr6_data, ioaddr);
uw32(DCR7, 0); /* Disable Interrupt */
uw32(DCR5, ur32(DCR5));
/* Disable upper layer interface */
netif_stop_queue(dev);
......@@ -1281,7 +1306,7 @@ static void uli526x_reuse_skb(struct uli526x_board_info *db, struct sk_buff * sk
* Using Chain structure, and allocate Tx/Rx buffer
*/
static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr)
static void uli526x_descriptor_init(struct net_device *dev, void __iomem *ioaddr)
{
struct uli526x_board_info *db = netdev_priv(dev);
struct tx_desc *tmp_tx;
......@@ -1296,14 +1321,14 @@ static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr
/* tx descriptor start pointer */
db->tx_insert_ptr = db->first_tx_desc;
db->tx_remove_ptr = db->first_tx_desc;
outl(db->first_tx_desc_dma, ioaddr + DCR4); /* TX DESC address */
uw32(DCR4, db->first_tx_desc_dma); /* TX DESC address */
/* rx descriptor start pointer */
db->first_rx_desc = (void *)db->first_tx_desc + sizeof(struct tx_desc) * TX_DESC_CNT;
db->first_rx_desc_dma = db->first_tx_desc_dma + sizeof(struct tx_desc) * TX_DESC_CNT;
db->rx_insert_ptr = db->first_rx_desc;
db->rx_ready_ptr = db->first_rx_desc;
outl(db->first_rx_desc_dma, ioaddr + DCR3); /* RX DESC address */
uw32(DCR3, db->first_rx_desc_dma); /* RX DESC address */
/* Init Transmit chain */
tmp_buf = db->buf_pool_start;
......@@ -1344,11 +1369,9 @@ static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr
* Update CR6 value
* Firstly stop ULI526X, then written value and start
*/
static void update_cr6(u32 cr6_data, unsigned long ioaddr)
static void update_cr6(u32 cr6_data, void __iomem *ioaddr)
{
outl(cr6_data, ioaddr + DCR6);
uw32(DCR6, cr6_data);
udelay(5);
}
......@@ -1367,6 +1390,7 @@ static void update_cr6(u32 cr6_data, unsigned long ioaddr)
static void send_filter_frame(struct net_device *dev, int mc_cnt)
{
struct uli526x_board_info *db = netdev_priv(dev);
void __iomem *ioaddr = db->ioaddr;
struct netdev_hw_addr *ha;
struct tx_desc *txptr;
u16 * addrptr;
......@@ -1412,9 +1436,9 @@ static void send_filter_frame(struct net_device *dev, int mc_cnt)
/* Resource Empty */
db->tx_packet_cnt++;
txptr->tdes0 = cpu_to_le32(0x80000000);
update_cr6(db->cr6_data | 0x2000, dev->base_addr);
outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */
update_cr6(db->cr6_data, dev->base_addr);
update_cr6(db->cr6_data | 0x2000, ioaddr);
uw32(DCR1, 0x1); /* Issue Tx polling */
update_cr6(db->cr6_data, ioaddr);
dev->trans_start = jiffies;
} else
netdev_err(dev, "No Tx resource - Send_filter_frame!\n");
......@@ -1457,37 +1481,38 @@ static void allocate_rx_buffer(struct net_device *dev)
* Read one word data from the serial ROM
*/
static u16 read_srom_word(long ioaddr, int offset)
static u16 read_srom_word(struct uli526x_board_info *db, int offset)
{
int i;
void __iomem *ioaddr = db->ioaddr;
u16 srom_data = 0;
long cr9_ioaddr = ioaddr + DCR9;
int i;
outl(CR9_SROM_READ, cr9_ioaddr);
outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr);
uw32(DCR9, CR9_SROM_READ);
uw32(DCR9, CR9_SROM_READ | CR9_SRCS);
/* Send the Read Command 110b */
SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr);
SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr);
SROM_CLK_WRITE(SROM_DATA_0, cr9_ioaddr);
srom_clk_write(db, SROM_DATA_1);
srom_clk_write(db, SROM_DATA_1);
srom_clk_write(db, SROM_DATA_0);
/* Send the offset */
for (i = 5; i >= 0; i--) {
srom_data = (offset & (1 << i)) ? SROM_DATA_1 : SROM_DATA_0;
SROM_CLK_WRITE(srom_data, cr9_ioaddr);
srom_clk_write(db, srom_data);
}
outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr);
uw32(DCR9, CR9_SROM_READ | CR9_SRCS);
for (i = 16; i > 0; i--) {
outl(CR9_SROM_READ | CR9_SRCS | CR9_SRCLK, cr9_ioaddr);
uw32(DCR9, CR9_SROM_READ | CR9_SRCS | CR9_SRCLK);
udelay(5);
srom_data = (srom_data << 1) | ((inl(cr9_ioaddr) & CR9_CRDOUT) ? 1 : 0);
outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr);
srom_data = (srom_data << 1) |
((ur32(DCR9) & CR9_CRDOUT) ? 1 : 0);
uw32(DCR9, CR9_SROM_READ | CR9_SRCS);
udelay(5);
}
outl(CR9_SROM_READ, cr9_ioaddr);
uw32(DCR9, CR9_SROM_READ);
return srom_data;
}
......@@ -1498,15 +1523,16 @@ static u16 read_srom_word(long ioaddr, int offset)
static u8 uli526x_sense_speed(struct uli526x_board_info * db)
{
struct uli_phy_ops *phy = &db->phy;
u8 ErrFlag = 0;
u16 phy_mode;
phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
phy_mode = phy->read(db, db->phy_addr, 1);
phy_mode = phy->read(db, db->phy_addr, 1);
if ( (phy_mode & 0x24) == 0x24 ) {
phy_mode = ((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)<<7);
phy_mode = ((phy->read(db, db->phy_addr, 5) & 0x01e0)<<7);
if(phy_mode&0x8000)
phy_mode = 0x8000;
else if(phy_mode&0x4000)
......@@ -1541,10 +1567,11 @@ static u8 uli526x_sense_speed(struct uli526x_board_info * db)
static void uli526x_set_phyxcer(struct uli526x_board_info *db)
{
struct uli_phy_ops *phy = &db->phy;
u16 phy_reg;
/* Phyxcer capability setting */
phy_reg = phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0;
phy_reg = phy->read(db, db->phy_addr, 4) & ~0x01e0;
if (db->media_mode & ULI526X_AUTO) {
/* AUTO Mode */
......@@ -1565,10 +1592,10 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db)
phy_reg|=db->PHY_reg4;
db->media_mode|=ULI526X_AUTO;
}
phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id);
phy->write(db, db->phy_addr, 4, phy_reg);
/* Restart Auto-Negotiation */
phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id);
phy->write(db, db->phy_addr, 0, 0x1200);
udelay(50);
}
......@@ -1582,6 +1609,7 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db)
static void uli526x_process_mode(struct uli526x_board_info *db)
{
struct uli_phy_ops *phy = &db->phy;
u16 phy_reg;
/* Full Duplex Mode Check */
......@@ -1593,10 +1621,10 @@ static void uli526x_process_mode(struct uli526x_board_info *db)
update_cr6(db->cr6_data, db->ioaddr);
/* 10/100M phyxcer force mode need */
if ( !(db->media_mode & 0x8)) {
if (!(db->media_mode & 0x8)) {
/* Forece Mode */
phy_reg = phy_read(db->ioaddr, db->phy_addr, 6, db->chip_id);
if ( !(phy_reg & 0x1) ) {
phy_reg = phy->read(db, db->phy_addr, 6);
if (!(phy_reg & 0x1)) {
/* parter without N-Way capability */
phy_reg = 0x0;
switch(db->op_mode) {
......@@ -1605,148 +1633,126 @@ static void uli526x_process_mode(struct uli526x_board_info *db)
case ULI526X_100MHF: phy_reg = 0x2000; break;
case ULI526X_100MFD: phy_reg = 0x2100; break;
}
phy_write(db->ioaddr, db->phy_addr, 0, phy_reg, db->chip_id);
phy->write(db, db->phy_addr, 0, phy_reg);
}
}
}
/*
* Write a word to Phy register
*/
static void phy_write(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data, u32 chip_id)
/* M5261/M5263 Chip */
static void phy_writeby_cr9(struct uli526x_board_info *db, u8 phy_addr,
u8 offset, u16 phy_data)
{
u16 i;
unsigned long ioaddr;
if(chip_id == PCI_ULI5263_ID)
{
phy_writeby_cr10(iobase, phy_addr, offset, phy_data);
return;
}
/* M5261/M5263 Chip */
ioaddr = iobase + DCR9;
/* Send 33 synchronization clock to Phy controller */
for (i = 0; i < 35; i++)
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(db, PHY_DATA_1);
/* Send start command(01) to Phy */
phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(db, PHY_DATA_0);
phy_write_1bit(db, PHY_DATA_1);
/* Send write command(01) to Phy */
phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(db, PHY_DATA_0);
phy_write_1bit(db, PHY_DATA_1);
/* Send Phy address */
for (i = 0x10; i > 0; i = i >> 1)
phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
phy_write_1bit(db, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
/* Send register address */
for (i = 0x10; i > 0; i = i >> 1)
phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
phy_write_1bit(db, offset & i ? PHY_DATA_1 : PHY_DATA_0);
/* written trasnition */
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
phy_write_1bit(db, PHY_DATA_1);
phy_write_1bit(db, PHY_DATA_0);
/* Write a word data to PHY controller */
for ( i = 0x8000; i > 0; i >>= 1)
phy_write_1bit(ioaddr, phy_data & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
for (i = 0x8000; i > 0; i >>= 1)
phy_write_1bit(db, phy_data & i ? PHY_DATA_1 : PHY_DATA_0);
}
/*
* Read a word data from phy register
*/
static u16 phy_read(unsigned long iobase, u8 phy_addr, u8 offset, u32 chip_id)
static u16 phy_readby_cr9(struct uli526x_board_info *db, u8 phy_addr, u8 offset)
{
int i;
u16 phy_data;
unsigned long ioaddr;
if(chip_id == PCI_ULI5263_ID)
return phy_readby_cr10(iobase, phy_addr, offset);
/* M5261/M5263 Chip */
ioaddr = iobase + DCR9;
int i;
/* Send 33 synchronization clock to Phy controller */
for (i = 0; i < 35; i++)
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(db, PHY_DATA_1);
/* Send start command(01) to Phy */
phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(db, PHY_DATA_0);
phy_write_1bit(db, PHY_DATA_1);
/* Send read command(10) to Phy */
phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
phy_write_1bit(db, PHY_DATA_1);
phy_write_1bit(db, PHY_DATA_0);
/* Send Phy address */
for (i = 0x10; i > 0; i = i >> 1)
phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
phy_write_1bit(db, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
/* Send register address */
for (i = 0x10; i > 0; i = i >> 1)
phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
phy_write_1bit(db, offset & i ? PHY_DATA_1 : PHY_DATA_0);
/* Skip transition state */
phy_read_1bit(ioaddr, chip_id);
phy_read_1bit(db);
/* read 16bit data */
for (phy_data = 0, i = 0; i < 16; i++) {
phy_data <<= 1;
phy_data |= phy_read_1bit(ioaddr, chip_id);
phy_data |= phy_read_1bit(db);
}
return phy_data;
}
static u16 phy_readby_cr10(unsigned long iobase, u8 phy_addr, u8 offset)
static u16 phy_readby_cr10(struct uli526x_board_info *db, u8 phy_addr,
u8 offset)
{
unsigned long ioaddr,cr10_value;
void __iomem *ioaddr = db->ioaddr;
u32 cr10_value = phy_addr;
ioaddr = iobase + DCR10;
cr10_value = phy_addr;
cr10_value = (cr10_value<<5) + offset;
cr10_value = (cr10_value<<16) + 0x08000000;
outl(cr10_value,ioaddr);
cr10_value = (cr10_value << 5) + offset;
cr10_value = (cr10_value << 16) + 0x08000000;
uw32(DCR10, cr10_value);
udelay(1);
while(1)
{
cr10_value = inl(ioaddr);
if(cr10_value&0x10000000)
while (1) {
cr10_value = ur32(DCR10);
if (cr10_value & 0x10000000)
break;
}
return cr10_value & 0x0ffff;
}
static void phy_writeby_cr10(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data)
static void phy_writeby_cr10(struct uli526x_board_info *db, u8 phy_addr,
u8 offset, u16 phy_data)
{
unsigned long ioaddr,cr10_value;
void __iomem *ioaddr = db->ioaddr;
u32 cr10_value = phy_addr;
ioaddr = iobase + DCR10;
cr10_value = phy_addr;
cr10_value = (cr10_value<<5) + offset;
cr10_value = (cr10_value<<16) + 0x04000000 + phy_data;
outl(cr10_value,ioaddr);
cr10_value = (cr10_value << 5) + offset;
cr10_value = (cr10_value << 16) + 0x04000000 + phy_data;
uw32(DCR10, cr10_value);
udelay(1);
}
/*
* Write one bit data to Phy Controller
*/
static void phy_write_1bit(unsigned long ioaddr, u32 phy_data, u32 chip_id)
static void phy_write_1bit(struct uli526x_board_info *db, u32 data)
{
outl(phy_data , ioaddr); /* MII Clock Low */
void __iomem *ioaddr = db->ioaddr;
uw32(DCR9, data); /* MII Clock Low */
udelay(1);
outl(phy_data | MDCLKH, ioaddr); /* MII Clock High */
uw32(DCR9, data | MDCLKH); /* MII Clock High */
udelay(1);
outl(phy_data , ioaddr); /* MII Clock Low */
uw32(DCR9, data); /* MII Clock Low */
udelay(1);
}
......@@ -1755,14 +1761,15 @@ static void phy_write_1bit(unsigned long ioaddr, u32 phy_data, u32 chip_id)
* Read one bit phy data from PHY controller
*/
static u16 phy_read_1bit(unsigned long ioaddr, u32 chip_id)
static u16 phy_read_1bit(struct uli526x_board_info *db)
{
void __iomem *ioaddr = db->ioaddr;
u16 phy_data;
outl(0x50000 , ioaddr);
uw32(DCR9, 0x50000);
udelay(1);
phy_data = ( inl(ioaddr) >> 19 ) & 0x1;
outl(0x40000 , ioaddr);
phy_data = (ur32(DCR9) >> 19) & 0x1;
uw32(DCR9, 0x40000);
udelay(1);
return phy_data;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment