Merge branch 'msm-core' of git://codeaurora.org/quic/kernel/dwalker/linux-msm into devel-stable

Documentation/arm/00-INDEX

@@ -6,6 +6,8 @@ Interrupts
 	- ARM Interrupt subsystem documentation
 IXP2000
 	- Release Notes for Linux on Intel's IXP2000 Network Processor
+msm
+	- MSM specific documentation
 Netwinder
 	- Netwinder specific documentation
 Porting

Documentation/arm/msm/gpiomux.txt

+This document provides an overview of the msm_gpiomux interface, which
+is used to provide gpio pin multiplexing and configuration on mach-msm
+targets.
+
+History
+=======
+
+The first-generation API for gpio configuration & multiplexing on msm
+is the function gpio_tlmm_config().  This function has a few notable
+shortcomings, which led to its deprecation and replacement by gpiomux:
+
+The 'disable' parameter:  Setting the second parameter to
+gpio_tlmm_config to GPIO_CFG_DISABLE tells the peripheral
+processor in charge of the subsystem to perform a look-up into a
+low-power table and apply the low-power/sleep setting for the pin.
+As the msm family evolved this became problematic. Not all pins
+have sleep settings, not all peripheral processors will accept requests
+to apply said sleep settings, and not all msm targets have their gpio
+subsystems managed by a peripheral processor. In order to get consistent
+behavior on all targets, drivers are forced to ignore this parameter,
+rendering it useless.
+
+The 'direction' flag: for all mux-settings other than raw-gpio (0),
+the output-enable bit of a gpio is hard-wired to a known
+input (usually VDD or ground).  For those settings, the direction flag
+is meaningless at best, and deceptive at worst.  In addition, using the
+direction flag to change output-enable (OE) directly can cause trouble in
+gpiolib, which has no visibility into gpio direction changes made
+in this way.  Direction control in gpio mode should be made through gpiolib.
+
+Key Features of gpiomux
+=======================
+
+- A consistent interface across all generations of msm.  Drivers can expect
+the same results on every target.
+- gpiomux plays nicely with gpiolib.  Functions that should belong to gpiolib
+are left to gpiolib and not duplicated here.  gpiomux is written with the
+intent that gpio_chips will call gpiomux reference-counting methods
+from their request() and free() hooks, providing full integration.
+- Tabular configuration.  Instead of having to call gpio_tlmm_config
+hundreds of times, gpio configuration is placed in a single table.
+- Per-gpio sleep.  Each gpio is individually reference counted, allowing only
+those lines which are in use to be put in high-power states.
+- 0 means 'do nothing': all flags are designed so that the default memset-zero
+equates to a sensible default of 'no configuration', preventing users
+from having to provide hundreds of 'no-op' configs for unused or
+unwanted lines.
+
+Usage
+=====
+
+To use gpiomux, provide configuration information for relevant gpio lines
+in the msm_gpiomux_configs table.  Since a 0 equates to "unconfigured",
+only those lines to be managed by gpiomux need to be specified.  Here
+is a completely fictional example:
+
+struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
+	[12] = {
+		.active = GPIOMUX_VALID | GPIOMUX_DRV_8MA | GPIOMUX_FUNC_1,
+		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
+	},
+	[34] = {
+		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
+	},
+};
+
+To indicate that a gpio is in use, call msm_gpiomux_get() to increase
+its reference count.  To decrease the reference count, call msm_gpiomux_put().
+
+The effect of this configuration is as follows:
+
+When the system boots, gpios 12 and 34 will be initialized with their
+'suspended' configurations.  All other gpios, which were left unconfigured,
+will not be touched.
+
+When msm_gpiomux_get() is called on gpio 12 to raise its reference count
+above 0, its active configuration will be applied.  Since no other gpio
+line has a valid active configuration, msm_gpiomux_get() will have no
+effect on any other line.
+
+When msm_gpiomux_put() is called on gpio 12 or 34 to drop their reference
+count to 0, their suspended configurations will be applied.
+Since no other gpio line has a valid suspended configuration, no other
+gpio line will be effected by msm_gpiomux_put().  Since gpio 34 has no valid
+active configuration, this is effectively a no-op for gpio 34 as well,
+with one small caveat, see the section "About Output-Enable Settings".
+
+All of the GPIOMUX_VALID flags may seem like unnecessary overhead, but
+they address some important issues.  As unused entries (all those
+except 12 and 34) are zero-filled, gpiomux needs a way to distinguish
+the used fields from the unused.  In addition, the all-zero pattern
+is a valid configuration!  Therefore, gpiomux defines an additional bit
+which is used to indicate when a field is used.  This has the pleasant
+side-effect of allowing calls to msm_gpiomux_write to use '0' to indicate
+that a value should not be changed:
+
+  msm_gpiomux_write(0, GPIOMUX_VALID, 0);
+
+replaces the active configuration of gpio 0 with an all-zero configuration,
+but leaves the suspended configuration as it was.
+
+Static Configurations
+=====================
+
+To install a static configuration, which is applied at boot and does
+not change after that, install a configuration with a suspended component
+but no active component, as in the previous example:
+
+	[34] = {
+		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
+	},
+
+The suspended setting is applied during boot, and the lack of any valid
+active setting prevents any other setting from being applied at runtime.
+If other subsystems attempting to access the line is a concern, one could
+*really* anchor the configuration down by calling msm_gpiomux_get on the
+line at initialization to move the line into active mode.  With the line
+held, it will never be re-suspended, and with no valid active configuration,
+no new configurations will be applied.
+
+But then, if having other subsystems grabbing for the line is truly a concern,
+it should be reserved with gpio_request instead, which carries an implicit
+msm_gpiomux_get.
+
+gpiomux and gpiolib
+===================
+
+It is expected that msm gpio_chips will call msm_gpiomux_get() and
+msm_gpiomux_put() from their request and free hooks, like this fictional
+example:
+
+static int request(struct gpio_chip *chip, unsigned offset)
+{
+        return msm_gpiomux_get(chip->base + offset);
+}
+
+static void free(struct gpio_chip *chip, unsigned offset)
+{
+        msm_gpiomux_put(chip->base + offset);
+}
+
+	...somewhere in a gpio_chip declaration...
+	.request = request,
+	.free    = free,
+
+This provides important functionality:
+- It guarantees that a gpio line will have its 'active' config applied
+  when the line is requested, and will not be suspended while the line
+  remains requested; and
+- It guarantees that gpio-direction settings from gpiolib behave sensibly.
+  See "About Output-Enable Settings."
+
+This mechanism allows for "auto-request" of gpiomux lines via gpiolib
+when it is suitable.  Drivers wishing more exact control are, of course,
+free to also use msm_gpiomux_set and msm_gpiomux_get.
+
+About Output-Enable Settings
+============================
+
+Some msm targets do not have the ability to query the current gpio
+configuration setting.  This means that changes made to the output-enable
+(OE) bit by gpiolib cannot be consistently detected and preserved by gpiomux.
+Therefore, when gpiomux applies a configuration setting, any direction
+settings which may have been applied by gpiolib are lost and the default
+input settings are re-applied.
+
+For this reason, drivers should not assume that gpio direction settings
+continue to hold if they free and then re-request a gpio.  This seems like
+common sense - after all, anybody could have obtained the line in the
+meantime - but it needs saying.
+
+This also means that calls to msm_gpiomux_write will reset the OE bit,
+which means that if the gpio line is held by a client of gpiolib and
+msm_gpiomux_write is called, the direction setting has been lost and
+gpiolib's internal state has been broken.
+Release gpio lines before reconfiguring them.

arch/arm/mach-msm/Kconfig

@@ -10,6 +10,8 @@ config ARCH_MSM7X00A
 	select MSM_SMD
 	select MSM_SMD_PKG3
 	select CPU_V6
+	select MSM_PROC_COMM
+	select HAS_MSM_DEBUG_UART_PHYS
 
 config ARCH_MSM7X30
 	bool "MSM7x30"
@@ -18,6 +20,9 @@ config ARCH_MSM7X30
 	select MSM_VIC
 	select CPU_V7
 	select MSM_REMOTE_SPINLOCK_DEKKERS
+	select MSM_GPIOMUX
+	select MSM_PROC_COMM
+	select HAS_MSM_DEBUG_UART_PHYS
 
 config ARCH_QSD8X50
 	bool "QSD8X50"
@@ -26,6 +31,19 @@ config ARCH_QSD8X50
 	select MSM_VIC
 	select CPU_V7
 	select MSM_REMOTE_SPINLOCK_LDREX
+	select MSM_GPIOMUX
+	select MSM_PROC_COMM
+	select HAS_MSM_DEBUG_UART_PHYS
+
+config ARCH_MSM8X60
+	bool "MSM8X60"
+	select ARM_GIC
+	select CPU_V7
+	select MSM_V2_TLMM
+	select MSM_GPIOMUX
+	select MACH_MSM8X60_SURF if (!MACH_MSM8X60_RUMI3 && !MACH_MSM8X60_SIM \
+				  && !MACH_MSM8X60_FFA)
+
 endchoice
 
 config MSM_SOC_REV_A
@@ -36,6 +54,9 @@ config  ARCH_MSM_ARM11
 config  ARCH_MSM_SCORPION
 	bool
 
+config HAS_MSM_DEBUG_UART_PHYS
+	bool
+
 config  MSM_VIC
 	bool
 
@@ -74,6 +95,30 @@ config MACH_QSD8X50A_ST1_5
 	help
 	  Support for the Qualcomm ST1.5.
 
+config MACH_MSM8X60_RUMI3
+	depends on ARCH_MSM8X60
+	bool "MSM8x60 RUMI3"
+	help
+	  Support for the Qualcomm MSM8x60 RUMI3 emulator.
+
+config MACH_MSM8X60_SURF
+	depends on ARCH_MSM8X60
+	bool "MSM8x60 SURF"
+	help
+	  Support for the Qualcomm MSM8x60 SURF eval board.
+
+config MACH_MSM8X60_SIM
+	depends on ARCH_MSM8X60
+	bool "MSM8x60 Simulator"
+	help
+	  Support for the Qualcomm MSM8x60 simulator.
+
+config MACH_MSM8X60_FFA
+	depends on ARCH_MSM8X60
+	bool "MSM8x60 FFA"
+	help
+	  Support for the Qualcomm MSM8x60 FFA eval board.
+
 endmenu
 
 config MSM_DEBUG_UART
@@ -82,6 +127,7 @@ config MSM_DEBUG_UART
 	default 2 if MSM_DEBUG_UART2
 	default 3 if MSM_DEBUG_UART3
 
+if HAS_MSM_DEBUG_UART_PHYS
 choice
 	prompt "Debug UART"
 
@@ -99,11 +145,20 @@ choice
 	config MSM_DEBUG_UART3
 		bool "UART3"
 endchoice
+endif
 
 config MSM_SMD_PKG3
 	bool
 
+config MSM_PROC_COMM
+	bool
+
 config MSM_SMD
 	bool
 
+config MSM_GPIOMUX
+	bool
+
+config MSM_V2_TLMM
+	bool
 endif

arch/arm/mach-msm/Makefile

-obj-y += proc_comm.o
-obj-y += io.o idle.o timer.o dma.o
-obj-y += vreg.o
+obj-y += io.o idle.o timer.o
+ifndef CONFIG_ARCH_MSM8X60
 obj-y += acpuclock-arm11.o
-obj-y += clock.o clock-pcom.o
-obj-y += gpio.o
+obj-y += dma.o
+endif
 
 ifdef CONFIG_MSM_VIC
 obj-y += irq-vic.o
 else
+ifndef CONFIG_ARCH_MSM8X60
 obj-y += irq.o
 endif
+endif
 
+obj-$(CONFIG_ARCH_MSM8X60) += clock-dummy.o iommu.o iommu_dev.o devices-msm8x60-iommu.o
+obj-$(CONFIG_MSM_PROC_COMM) += proc_comm.o clock-pcom.o vreg.o
+obj-$(CONFIG_MSM_PROC_COMM) += clock.o
 obj-$(CONFIG_ARCH_QSD8X50) += sirc.o
 obj-$(CONFIG_MSM_SMD) += smd.o smd_debug.o
 obj-$(CONFIG_MSM_SMD) += last_radio_log.o
@@ -19,4 +23,11 @@ obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o d
 obj-$(CONFIG_MACH_HALIBUT) += board-halibut.o devices-msm7x00.o
 obj-$(CONFIG_ARCH_MSM7X30) += board-msm7x30.o devices-msm7x30.o
 obj-$(CONFIG_ARCH_QSD8X50) += board-qsd8x50.o devices-qsd8x50.o
+obj-$(CONFIG_ARCH_MSM8X60) += board-msm8x60.o
 
+obj-$(CONFIG_ARCH_MSM7X30) += gpiomux-7x30.o gpiomux-v1.o gpiomux.o
+obj-$(CONFIG_ARCH_QSD8X50) += gpiomux-8x50.o gpiomux-v1.o gpiomux.o
+obj-$(CONFIG_ARCH_MSM8X60) += gpiomux-8x60.o gpiomux-v2.o gpiomux.o
+ifndef CONFIG_MSM_V2_TLMM
+obj-y	+= gpio.o
+endif

arch/arm/mach-msm/board-msm7x30.c

@@ -39,27 +39,11 @@
 
 extern struct sys_timer msm_timer;
 
-#ifdef CONFIG_SERIAL_MSM_CONSOLE
-static struct msm_gpio uart2_config_data[] = {
-	{ GPIO_CFG(49, 2, GPIO_OUTPUT,  GPIO_PULL_DOWN, GPIO_2MA), "UART2_RFR"},
-	{ GPIO_CFG(50, 2, GPIO_INPUT,   GPIO_PULL_DOWN, GPIO_2MA), "UART2_CTS"},
-	{ GPIO_CFG(51, 2, GPIO_INPUT,   GPIO_PULL_DOWN, GPIO_2MA), "UART2_Rx"},
-	{ GPIO_CFG(52, 2, GPIO_OUTPUT,  GPIO_PULL_DOWN, GPIO_2MA), "UART2_Tx"},
-};
-
-static void msm7x30_init_uart2(void)
-{
-	msm_gpios_request_enable(uart2_config_data,
-			ARRAY_SIZE(uart2_config_data));
-
-}
-#endif
-
 static struct platform_device *devices[] __initdata = {
 #if defined(CONFIG_SERIAL_MSM) || defined(CONFIG_MSM_SERIAL_DEBUGGER)
         &msm_device_uart2,
 #endif
-
+	&msm_device_smd,
 };
 
 static void __init msm7x30_init_irq(void)
@@ -70,10 +54,6 @@ static void __init msm7x30_init_irq(void)
 static void __init msm7x30_init(void)
 {
 	platform_add_devices(devices, ARRAY_SIZE(devices));
-#ifdef CONFIG_SERIAL_MSM_CONSOLE
-	msm7x30_init_uart2();
-#endif
-
 }
 
 static void __init msm7x30_map_io(void)

arch/arm/mach-msm/board-msm8x60.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/hardware/gic.h>
+
+#include <mach/board.h>
+#include <mach/msm_iomap.h>
+
+void __iomem *gic_cpu_base_addr;
+
+unsigned long clk_get_max_axi_khz(void)
+{
+	return 0;
+}
+
+static void __init msm8x60_map_io(void)
+{
+	msm_map_msm8x60_io();
+}
+
+static void __init msm8x60_init_irq(void)
+{
+	unsigned int i;
+
+	gic_dist_init(0, MSM_QGIC_DIST_BASE, GIC_PPI_START);
+	gic_cpu_base_addr = (void *)MSM_QGIC_CPU_BASE;
+	gic_cpu_init(0, MSM_QGIC_CPU_BASE);
+
+	/* Edge trigger PPIs except AVS_SVICINT and AVS_SVICINTSWDONE */
+	writel(0xFFFFD7FF, MSM_QGIC_DIST_BASE + GIC_DIST_CONFIG + 4);
+
+	/* RUMI does not adhere to GIC spec by enabling STIs by default.
+	 * Enable/clear is supposed to be RO for STIs, but is RW on RUMI.
+	 */
+	if (!machine_is_msm8x60_sim())
+		writel(0x0000FFFF, MSM_QGIC_DIST_BASE + GIC_DIST_ENABLE_SET);
+
+	/* FIXME: Not installing AVS_SVICINT and AVS_SVICINTSWDONE yet
+	 * as they are configured as level, which does not play nice with
+	 * handle_percpu_irq.
+	 */
+	for (i = GIC_PPI_START; i < GIC_SPI_START; i++) {
+		if (i != AVS_SVICINT && i != AVS_SVICINTSWDONE)
+			set_irq_handler(i, handle_percpu_irq);
+	}
+}
+
+static void __init msm8x60_init(void)
+{
+}
+
+MACHINE_START(MSM8X60_RUMI3, "QCT MSM8X60 RUMI3")
+	.map_io = msm8x60_map_io,
+	.init_irq = msm8x60_init_irq,
+	.init_machine = msm8x60_init,
+	.timer = &msm_timer,
+MACHINE_END
+
+MACHINE_START(MSM8X60_SURF, "QCT MSM8X60 SURF")
+	.map_io = msm8x60_map_io,
+	.init_irq = msm8x60_init_irq,
+	.init_machine = msm8x60_init,
+	.timer = &msm_timer,
+MACHINE_END
+
+MACHINE_START(MSM8X60_SIM, "QCT MSM8X60 SIMULATOR")
+	.map_io = msm8x60_map_io,
+	.init_irq = msm8x60_init_irq,
+	.init_machine = msm8x60_init,
+	.timer = &msm_timer,
+MACHINE_END
+
+MACHINE_START(MSM8X60_FFA, "QCT MSM8X60 FFA")
+	.map_io = msm8x60_map_io,
+	.init_irq = msm8x60_init_irq,
+	.init_machine = msm8x60_init,
+	.timer = &msm_timer,
+MACHINE_END

arch/arm/mach-msm/board-qsd8x50.c

@@ -35,20 +35,49 @@
 
 extern struct sys_timer msm_timer;
 
-static struct msm_gpio uart3_config_data[] = {
-	{ GPIO_CFG(86, 1, GPIO_INPUT,   GPIO_PULL_DOWN, GPIO_2MA), "UART2_Rx"},
-	{ GPIO_CFG(87, 1, GPIO_OUTPUT,  GPIO_PULL_DOWN, GPIO_2MA), "UART2_Tx"},
+static const resource_size_t qsd8x50_surf_smc91x_base __initdata = 0x70000300;
+static const unsigned        qsd8x50_surf_smc91x_gpio __initdata = 156;
+
+/* Leave smc91x resources empty here, as we'll fill them in
+ * at run-time: they vary from board to board, and the true
+ * configuration won't be known until boot.
+ */
+static struct resource smc91x_resources[] __initdata = {
+	[0] = {
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.flags = IORESOURCE_IRQ,
+	},
 };
 
-static struct platform_device *devices[] __initdata = {
-	&msm_device_uart3,
+static struct platform_device smc91x_device __initdata = {
+	.name           = "smc91x",
+	.id             = 0,
+	.num_resources  = ARRAY_SIZE(smc91x_resources),
+	.resource       = smc91x_resources,
 };
 
-static void msm8x50_init_uart3(void)
+static int __init msm_init_smc91x(void)
 {
-	msm_gpios_request_enable(uart3_config_data,
-				ARRAY_SIZE(uart3_config_data));
+	if (machine_is_qsd8x50_surf()) {
+		smc91x_resources[0].start = qsd8x50_surf_smc91x_base;
+		smc91x_resources[0].end   = qsd8x50_surf_smc91x_base + 0xff;
+		smc91x_resources[1].start =
+			gpio_to_irq(qsd8x50_surf_smc91x_gpio);
+		smc91x_resources[1].end   =
+			gpio_to_irq(qsd8x50_surf_smc91x_gpio);
+		platform_device_register(&smc91x_device);
+	}
+
+	return 0;
 }
+module_init(msm_init_smc91x);
+
+static struct platform_device *devices[] __initdata = {
+	&msm_device_uart3,
+	&msm_device_smd,
+};
 
 static void __init qsd8x50_map_io(void)
 {
@@ -64,7 +93,6 @@ static void __init qsd8x50_init_irq(void)
 
 static void __init qsd8x50_init(void)
 {
-	msm8x50_init_uart3();
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 }
 

arch/arm/mach-msm/clock-dummy.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ *
+ */
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/module.h>
+
+struct clk *clk_get(struct device *dev, const char *id)
+{
+	return ERR_PTR(-ENOENT);
+}
+EXPORT_SYMBOL(clk_get);
+
+int clk_enable(struct clk *clk)
+{
+	return -ENOENT;
+}
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_disable);
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	return -ENOENT;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
+void clk_put(struct clk *clk)
+{
+}
+EXPORT_SYMBOL(clk_put);

arch/arm/mach-msm/devices-msm7x30.c

@@ -51,6 +51,11 @@ struct platform_device msm_device_uart2 = {
 	.resource	= resources_uart2,
 };
 
+struct platform_device msm_device_smd = {
+	.name   = "msm_smd",
+	.id     = -1,
+};
+
 struct clk msm_clocks_7x30[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),

arch/arm/mach-msm/devices-qsd8x50.c

@@ -48,6 +48,11 @@ struct platform_device msm_device_uart3 = {
 	.resource	= resources_uart3,
 };
 
+struct platform_device msm_device_smd = {
+	.name   = "msm_smd",
+	.id     = -1,
+};
+
 struct clk msm_clocks_8x50[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, CLK_MIN),

arch/arm/mach-msm/gpiomux-7x30.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#include "gpiomux.h"
+
+struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
+#ifdef CONFIG_SERIAL_MSM_CONSOLE
+	[49] = { /* UART2 RFR */
+		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
+			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
+	},
+	[50] = { /* UART2 CTS */
+		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
+			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
+	},
+	[51] = { /* UART2 RX */
+		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
+			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
+	},
+	[52] = { /* UART2 TX */
+		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
+			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
+	},
+#endif
+};

arch/arm/mach-msm/gpiomux-8x50.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#include "gpiomux.h"
+
+struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
+	[86] = { /* UART3 RX */
+		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
+			     GPIOMUX_FUNC_1 | GPIOMUX_VALID,
+	},
+	[87] = { /* UART3 TX */
+		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
+			     GPIOMUX_FUNC_1 | GPIOMUX_VALID,
+	},
+};

arch/arm/mach-msm/gpiomux-8x60.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#include "gpiomux.h"
+
+struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {};

arch/arm/mach-msm/gpiomux-v1.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#include <linux/kernel.h>
+#include "gpiomux.h"
+#include "proc_comm.h"
+
+void __msm_gpiomux_write(unsigned gpio, gpiomux_config_t val)
+{
+	unsigned tlmm_config  = (val & ~GPIOMUX_CTL_MASK) |
+				((gpio & 0x3ff) << 4);
+	unsigned tlmm_disable = 0;
+	int rc;
+
+	rc = msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX,
+			   &tlmm_config, &tlmm_disable);
+	if (rc)
+		pr_err("%s: unexpected proc_comm failure %d: %08x %08x\n",
+		       __func__, rc, tlmm_config, tlmm_disable);
+}

arch/arm/mach-msm/gpiomux-v1.h

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIOMUX_V1_H
+#define __ARCH_ARM_MACH_MSM_GPIOMUX_V1_H
+
+#if defined(CONFIG_ARCH_MSM7X30)
+#define GPIOMUX_NGPIOS 182
+#elif defined(CONFIG_ARCH_QSD8X50)
+#define GPIOMUX_NGPIOS 165
+#else
+#define GPIOMUX_NGPIOS 133
+#endif
+
+typedef u32 gpiomux_config_t;
+
+enum {
+	GPIOMUX_DRV_2MA  = 0UL << 17,
+	GPIOMUX_DRV_4MA  = 1UL << 17,
+	GPIOMUX_DRV_6MA  = 2UL << 17,
+	GPIOMUX_DRV_8MA  = 3UL << 17,
+	GPIOMUX_DRV_10MA = 4UL << 17,
+	GPIOMUX_DRV_12MA = 5UL << 17,
+	GPIOMUX_DRV_14MA = 6UL << 17,
+	GPIOMUX_DRV_16MA = 7UL << 17,
+};
+
+enum {
+	GPIOMUX_FUNC_GPIO = 0UL,
+	GPIOMUX_FUNC_1    = 1UL,
+	GPIOMUX_FUNC_2    = 2UL,
+	GPIOMUX_FUNC_3    = 3UL,
+	GPIOMUX_FUNC_4    = 4UL,
+	GPIOMUX_FUNC_5    = 5UL,
+	GPIOMUX_FUNC_6    = 6UL,
+	GPIOMUX_FUNC_7    = 7UL,
+	GPIOMUX_FUNC_8    = 8UL,
+	GPIOMUX_FUNC_9    = 9UL,
+	GPIOMUX_FUNC_A    = 10UL,
+	GPIOMUX_FUNC_B    = 11UL,
+	GPIOMUX_FUNC_C    = 12UL,
+	GPIOMUX_FUNC_D    = 13UL,
+	GPIOMUX_FUNC_E    = 14UL,
+	GPIOMUX_FUNC_F    = 15UL,
+};
+
+enum {
+	GPIOMUX_PULL_NONE   = 0UL << 15,
+	GPIOMUX_PULL_DOWN   = 1UL << 15,
+	GPIOMUX_PULL_KEEPER = 2UL << 15,
+	GPIOMUX_PULL_UP     = 3UL << 15,
+};
+
+#endif

arch/arm/mach-msm/gpiomux-v2.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#include <linux/io.h>
+#include <mach/msm_iomap.h>
+#include "gpiomux.h"
+
+void __msm_gpiomux_write(unsigned gpio, gpiomux_config_t val)
+{
+	writel(val & ~GPIOMUX_CTL_MASK,
+	       MSM_TLMM_BASE + 0x1000 + (0x10 * gpio));
+}

arch/arm/mach-msm/gpiomux-v2.h

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIOMUX_V2_H
+#define __ARCH_ARM_MACH_MSM_GPIOMUX_V2_H
+
+#define GPIOMUX_NGPIOS 173
+
+typedef u16 gpiomux_config_t;
+
+enum {
+	GPIOMUX_DRV_2MA  = 0UL << 6,
+	GPIOMUX_DRV_4MA  = 1UL << 6,
+	GPIOMUX_DRV_6MA  = 2UL << 6,
+	GPIOMUX_DRV_8MA  = 3UL << 6,
+	GPIOMUX_DRV_10MA = 4UL << 6,
+	GPIOMUX_DRV_12MA = 5UL << 6,
+	GPIOMUX_DRV_14MA = 6UL << 6,
+	GPIOMUX_DRV_16MA = 7UL << 6,
+};
+
+enum {
+	GPIOMUX_FUNC_GPIO = 0UL  << 2,
+	GPIOMUX_FUNC_1    = 1UL  << 2,
+	GPIOMUX_FUNC_2    = 2UL  << 2,
+	GPIOMUX_FUNC_3    = 3UL  << 2,
+	GPIOMUX_FUNC_4    = 4UL  << 2,
+	GPIOMUX_FUNC_5    = 5UL  << 2,
+	GPIOMUX_FUNC_6    = 6UL  << 2,
+	GPIOMUX_FUNC_7    = 7UL  << 2,
+	GPIOMUX_FUNC_8    = 8UL  << 2,
+	GPIOMUX_FUNC_9    = 9UL  << 2,
+	GPIOMUX_FUNC_A    = 10UL << 2,
+	GPIOMUX_FUNC_B    = 11UL << 2,
+	GPIOMUX_FUNC_C    = 12UL << 2,
+	GPIOMUX_FUNC_D    = 13UL << 2,
+	GPIOMUX_FUNC_E    = 14UL << 2,
+	GPIOMUX_FUNC_F    = 15UL << 2,
+};
+
+enum {
+	GPIOMUX_PULL_NONE   = 0UL,
+	GPIOMUX_PULL_DOWN   = 1UL,
+	GPIOMUX_PULL_KEEPER = 2UL,
+	GPIOMUX_PULL_UP     = 3UL,
+};
+
+#endif

arch/arm/mach-msm/gpiomux.c

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include "gpiomux.h"
+
+static DEFINE_SPINLOCK(gpiomux_lock);
+
+int msm_gpiomux_write(unsigned gpio,
+		      gpiomux_config_t active,
+		      gpiomux_config_t suspended)
+{
+	struct msm_gpiomux_config *cfg = msm_gpiomux_configs + gpio;
+	unsigned long irq_flags;
+	gpiomux_config_t setting;
+
+	if (gpio >= GPIOMUX_NGPIOS)
+		return -EINVAL;
+
+	spin_lock_irqsave(&gpiomux_lock, irq_flags);
+
+	if (active & GPIOMUX_VALID)
+		cfg->active = active;
+
+	if (suspended & GPIOMUX_VALID)
+		cfg->suspended = suspended;
+
+	setting = cfg->ref ? active : suspended;
+	if (setting & GPIOMUX_VALID)
+		__msm_gpiomux_write(gpio, setting);
+
+	spin_unlock_irqrestore(&gpiomux_lock, irq_flags);
+	return 0;
+}
+EXPORT_SYMBOL(msm_gpiomux_write);
+
+int msm_gpiomux_get(unsigned gpio)
+{
+	struct msm_gpiomux_config *cfg = msm_gpiomux_configs + gpio;
+	unsigned long irq_flags;
+
+	if (gpio >= GPIOMUX_NGPIOS)
+		return -EINVAL;
+
+	spin_lock_irqsave(&gpiomux_lock, irq_flags);
+	if (cfg->ref++ == 0 && cfg->active & GPIOMUX_VALID)
+		__msm_gpiomux_write(gpio, cfg->active);
+	spin_unlock_irqrestore(&gpiomux_lock, irq_flags);
+	return 0;
+}
+EXPORT_SYMBOL(msm_gpiomux_get);
+
+int msm_gpiomux_put(unsigned gpio)
+{
+	struct msm_gpiomux_config *cfg = msm_gpiomux_configs + gpio;
+	unsigned long irq_flags;
+
+	if (gpio >= GPIOMUX_NGPIOS)
+		return -EINVAL;
+
+	spin_lock_irqsave(&gpiomux_lock, irq_flags);
+	BUG_ON(cfg->ref == 0);
+	if (--cfg->ref == 0 && cfg->suspended & GPIOMUX_VALID)
+		__msm_gpiomux_write(gpio, cfg->suspended);
+	spin_unlock_irqrestore(&gpiomux_lock, irq_flags);
+	return 0;
+}
+EXPORT_SYMBOL(msm_gpiomux_put);
+
+static int __init gpiomux_init(void)
+{
+	unsigned n;
+
+	for (n = 0; n < GPIOMUX_NGPIOS; ++n) {
+		msm_gpiomux_configs[n].ref = 0;
+		if (!(msm_gpiomux_configs[n].suspended & GPIOMUX_VALID))
+			continue;
+		__msm_gpiomux_write(n, msm_gpiomux_configs[n].suspended);
+	}
+	return 0;
+}
+postcore_initcall(gpiomux_init);

arch/arm/mach-msm/gpiomux.h

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIOMUX_H
+#define __ARCH_ARM_MACH_MSM_GPIOMUX_H
+
+#include <linux/bitops.h>
+#include <linux/errno.h>
+
+#if defined(CONFIG_MSM_V2_TLMM)
+#include "gpiomux-v2.h"
+#else
+#include "gpiomux-v1.h"
+#endif
+
+/**
+ * struct msm_gpiomux_config: gpiomux settings for one gpio line.
+ *
+ * A complete gpiomux config is the bitwise-or of a drive-strength,
+ * function, and pull.  For functions other than GPIO, the OE
+ * is hard-wired according to the function.  For GPIO mode,
+ * OE is controlled by gpiolib.
+ *
+ * Available settings differ by target; see the gpiomux header
+ * specific to your target arch for available configurations.
+ *
+ * @active: The configuration to be installed when the line is
+ * active, or its reference count is > 0.
+ * @suspended: The configuration to be installed when the line
+ * is suspended, or its reference count is 0.
+ * @ref: The reference count of the line.  For internal use of
+ * the gpiomux framework only.
+ */
+struct msm_gpiomux_config {
+	gpiomux_config_t active;
+	gpiomux_config_t suspended;
+	unsigned         ref;
+};
+
+/**
+ * @GPIOMUX_VALID:	If set, the config field contains 'good data'.
+ *                      The absence of this bit will prevent the gpiomux
+ *			system from applying the configuration under all
+ *			circumstances.
+ */
+enum {
+	GPIOMUX_VALID	 = BIT(sizeof(gpiomux_config_t) * BITS_PER_BYTE - 1),
+	GPIOMUX_CTL_MASK = GPIOMUX_VALID,
+};
+
+#ifdef CONFIG_MSM_GPIOMUX
+
+/* Each architecture must provide its own instance of this table.
+ * To avoid having gpiomux manage any given gpio, one or both of
+ * the entries can avoid setting GPIOMUX_VALID - the absence
+ * of that flag will prevent the configuration from being applied
+ * during state transitions.
+ */
+extern struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS];
+
+/* Increment a gpio's reference count, possibly activating the line. */
+int __must_check msm_gpiomux_get(unsigned gpio);
+
+/* Decrement a gpio's reference count, possibly suspending the line. */
+int msm_gpiomux_put(unsigned gpio);
+
+/* Install a new configuration to the gpio line.  To avoid overwriting
+ * a configuration, leave the VALID bit out.
+ */
+int msm_gpiomux_write(unsigned gpio,
+		      gpiomux_config_t active,
+		      gpiomux_config_t suspended);
+
+/* Architecture-internal function for use by the framework only.
+ * This function can assume the following:
+ * - the gpio value has passed a bounds-check
+ * - the gpiomux spinlock has been obtained
+ *
+ * This function is not for public consumption.  External users
+ * should use msm_gpiomux_write.
+ */
+void __msm_gpiomux_write(unsigned gpio, gpiomux_config_t val);
+#else
+static inline int __must_check msm_gpiomux_get(unsigned gpio)
+{
+	return -ENOSYS;
+}
+
+static inline int msm_gpiomux_put(unsigned gpio)
+{
+	return -ENOSYS;
+}
+
+static inline int msm_gpiomux_write(unsigned gpio,
+				    gpiomux_config_t active,
+				    gpiomux_config_t suspended)
+{
+	return -ENOSYS;
+}
+#endif
+#endif

arch/arm/mach-msm/include/mach/board.h

@@ -33,6 +33,8 @@ struct msm_acpu_clock_platform_data
 
 struct clk;
 
+extern struct sys_timer msm_timer;
+
 /* common init routines for use by arch/arm/mach-msm/board-*.c */
 
 void __init msm_add_devices(void);

arch/arm/mach-msm/include/mach/debug-macro.S

@@ -19,7 +19,7 @@
 #include <mach/hardware.h>
 #include <mach/msm_iomap.h>
 
-#ifdef CONFIG_MSM_DEBUG_UART
+#ifdef CONFIG_HAS_MSM_DEBUG_UART_PHYS
 	.macro	addruart, rx, tmp
 	@ see if the MMU is enabled and select appropriate base address
 	mrc	p15, 0, \rx, c1, c0

arch/arm/mach-msm/include/mach/dma.h

@@ -32,10 +32,18 @@ struct msm_dmov_cmd {
 	void *data;
 };
 
+#ifndef CONFIG_ARCH_MSM8X60
 void msm_dmov_enqueue_cmd(unsigned id, struct msm_dmov_cmd *cmd);
 void msm_dmov_stop_cmd(unsigned id, struct msm_dmov_cmd *cmd, int graceful);
 int msm_dmov_exec_cmd(unsigned id, unsigned int cmdptr);
-
+#else
+static inline
+void msm_dmov_enqueue_cmd(unsigned id, struct msm_dmov_cmd *cmd) { }
+static inline
+void msm_dmov_stop_cmd(unsigned id, struct msm_dmov_cmd *cmd, int graceful) { }
+static inline
+int msm_dmov_exec_cmd(unsigned id, unsigned int cmdptr) { return -EIO; }
+#endif
 
 
 #define DMOV_SD0(off, ch) (MSM_DMOV_BASE + 0x0000 + (off) + ((ch) << 2))

arch/arm/mach-msm/include/mach/entry-macro-qgic.S

+/*
+ * Low-level IRQ helper macros
+ *
+ * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <mach/hardware.h>
+#include <asm/hardware/gic.h>
+
+	.macro	disable_fiq
+	.endm
+
+	.macro  get_irqnr_preamble, base, tmp
+	ldr	\base, =gic_cpu_base_addr
+	ldr	\base, [\base]
+	.endm
+
+	.macro  arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	/*
+	 * The interrupt numbering scheme is defined in the
+	 * interrupt controller spec.  To wit:
+	 *
+	 * Migrated the code from ARM MP port to be more consistant
+	 * with interrupt processing , the following still holds true
+	 * however, all interrupts are treated the same regardless of
+	 * if they are local IPI or PPI
+	 *
+	 * Interrupts 0-15 are IPI
+	 * 16-31 are PPI
+	 *   (16-18 are the timers)
+	 * 32-1020 are global
+	 * 1021-1022 are reserved
+	 * 1023 is "spurious" (no interrupt)
+	 *
+	 * A simple read from the controller will tell us the number of the
+	 * highest priority enabled interrupt.  We then just need to check
+	 * whether it is in the valid range for an IRQ (0-1020 inclusive).
+	 *
+	 * Base ARM code assumes that the local (private) peripheral interrupts
+	 * are not valid, we treat them differently, in that the privates are
+	 * handled like normal shared interrupts with the exception that only
+	 * one processor can register the interrupt and the handler must be
+	 * the same for all processors.
+	 */
+
+	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+	ldr  \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 =srcCPU,
+						   9-0 =int # */
+
+	bic     \irqnr, \irqstat, #0x1c00	@mask src
+	cmp     \irqnr, #15
+	ldr		\tmp, =1021
+	cmpcc	\irqnr, \irqnr
+	cmpne	\irqnr, \tmp
+	cmpcs	\irqnr, \irqnr
+
+	.endm
+
+	/* We assume that irqstat (the raw value of the IRQ acknowledge
+	 * register) is preserved from the macro above.
+	 * If there is an IPI, we immediately signal end of interrupt on the
+	 * controller, since this requires the original irqstat value which
+	 * we won't easily be able to recreate later.
+	 */
+	.macro test_for_ipi, irqnr, irqstat, base, tmp
+    bic \irqnr, \irqstat, #0x1c00
+    cmp \irqnr, #16
+    strcc   \irqstat, [\base, #GIC_CPU_EOI]
+    cmpcs   \irqnr, \irqnr
+	.endm
+
+	/* As above, this assumes that irqstat and base are preserved.. */
+
+	.macro test_for_ltirq, irqnr, irqstat, base, tmp
+    bic \irqnr, \irqstat, #0x1c00
+    mov     \tmp, #0
+    cmp \irqnr, #16
+    moveq   \tmp, #1
+    streq   \irqstat, [\base, #GIC_CPU_EOI]
+    cmp \tmp, #0
+	.endm

arch/arm/mach-msm/include/mach/entry-macro-vic.S

+/*
+ * Copyright (C) 2007 Google, Inc.
+ * Author: Brian Swetland <swetland@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <mach/msm_iomap.h>
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	get_irqnr_preamble, base, tmp
+	@ enable imprecise aborts
+	cpsie	a
+	mov	\base, #MSM_VIC_BASE
+	.endm
+
+	.macro	arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+	@ 0xD0 has irq# or old irq# if the irq has been handled
+	@ 0xD4 has irq# or -1 if none pending *but* if you just
+	@ read 0xD4 you never get the first irq for some reason
+	ldr	\irqnr, [\base, #0xD0]
+	ldr	\irqnr, [\base, #0xD4]
+	cmp	\irqnr, #0xffffffff
+	.endm

arch/arm/mach-msm/include/mach/entry-macro.S

-/* arch/arm/mach-msm7200/include/mach/entry-macro.S
+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
  *
- * Copyright (C) 2007 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ *
  */
 
-#include <mach/msm_iomap.h>
-
- 	.macro	disable_fiq
-	.endm
-
-	.macro	get_irqnr_preamble, base, tmp
-	@ enable imprecise aborts
-	cpsie	a
-	mov	\base, #MSM_VIC_BASE
-	.endm
-
-	.macro	arch_ret_to_user, tmp1, tmp2
-	.endm
-
-	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-	@ 0xD0 has irq# or old irq# if the irq has been handled
-	@ 0xD4 has irq# or -1 if none pending *but* if you just
-	@ read 0xD4 you never get the first irq for some reason
-	ldr	\irqnr, [\base, #0xD0]
-	ldr	\irqnr, [\base, #0xD4]
-	cmp	\irqnr, #0xffffffff
-	.endm
+#if defined(CONFIG_ARM_GIC)
+#include <mach/entry-macro-qgic.S>
+#else
+#include <mach/entry-macro-vic.S>
+#endif

arch/arm/mach-msm/include/mach/gpio.h

@@ -23,127 +23,4 @@
 #define gpio_cansleep   __gpio_cansleep
 #define gpio_to_irq     __gpio_to_irq
 
-/**
- * struct msm_gpio - GPIO pin description
- * @gpio_cfg - configuration bitmap, as per gpio_tlmm_config()
- * @label - textual label
- *
- * Usually, GPIO's are operated by sets.
- * This struct accumulate all GPIO information in single source
- * and facilitete group operations provided by msm_gpios_xxx()
- */
-struct msm_gpio {
-	u32 gpio_cfg;
-	const char *label;
-};
-
-/**
- * msm_gpios_request_enable() - request and enable set of GPIOs
- *
- * Request and configure set of GPIO's
- * In case of error, all operations rolled back.
- * Return error code.
- *
- * @table: GPIO table
- * @size:  number of entries in @table
- */
-int msm_gpios_request_enable(const struct msm_gpio *table, int size);
-
-/**
- * msm_gpios_disable_free() - disable and free set of GPIOs
- *
- * @table: GPIO table
- * @size:  number of entries in @table
- */
-void msm_gpios_disable_free(const struct msm_gpio *table, int size);
-
-/**
- * msm_gpios_request() - request set of GPIOs
- * In case of error, all operations rolled back.
- * Return error code.
- *
- * @table: GPIO table
- * @size:  number of entries in @table
- */
-int msm_gpios_request(const struct msm_gpio *table, int size);
-
-/**
- * msm_gpios_free() - free set of GPIOs
- *
- * @table: GPIO table
- * @size:  number of entries in @table
- */
-void msm_gpios_free(const struct msm_gpio *table, int size);
-
-/**
- * msm_gpios_enable() - enable set of GPIOs
- * In case of error, all operations rolled back.
- * Return error code.
- *
- * @table: GPIO table
- * @size:  number of entries in @table
- */
-int msm_gpios_enable(const struct msm_gpio *table, int size);
-
-/**
- * msm_gpios_disable() - disable set of GPIOs
- *
- * @table: GPIO table
- * @size:  number of entries in @table
- */
-void msm_gpios_disable(const struct msm_gpio *table, int size);
-
-/* GPIO TLMM (Top Level Multiplexing) Definitions */
-
-/* GPIO TLMM: Function -- GPIO specific */
-
-/* GPIO TLMM: Direction */
-enum {
-	GPIO_INPUT,
-	GPIO_OUTPUT,
-};
-
-/* GPIO TLMM: Pullup/Pulldown */
-enum {
-	GPIO_NO_PULL,
-	GPIO_PULL_DOWN,
-	GPIO_KEEPER,
-	GPIO_PULL_UP,
-};
-
-/* GPIO TLMM: Drive Strength */
-enum {
-	GPIO_2MA,
-	GPIO_4MA,
-	GPIO_6MA,
-	GPIO_8MA,
-	GPIO_10MA,
-	GPIO_12MA,
-	GPIO_14MA,
-	GPIO_16MA,
-};
-
-enum {
-	GPIO_ENABLE,
-	GPIO_DISABLE,
-};
-
-#define GPIO_CFG(gpio, func, dir, pull, drvstr) \
-	((((gpio) & 0x3FF) << 4)        |	  \
-	 ((func) & 0xf)                  |	  \
-	 (((dir) & 0x1) << 14)           |	  \
-	 (((pull) & 0x3) << 15)          |	  \
-	 (((drvstr) & 0xF) << 17))
-
-/**
- * extract GPIO pin from bit-field used for gpio_tlmm_config
- */
-#define GPIO_PIN(gpio_cfg)    (((gpio_cfg) >>  4) & 0x3ff)
-#define GPIO_FUNC(gpio_cfg)   (((gpio_cfg) >>  0) & 0xf)
-#define GPIO_DIR(gpio_cfg)    (((gpio_cfg) >> 14) & 0x1)
-#define GPIO_PULL(gpio_cfg)   (((gpio_cfg) >> 15) & 0x3)
-#define GPIO_DRVSTR(gpio_cfg) (((gpio_cfg) >> 17) & 0xf)
-
-int gpio_tlmm_config(unsigned config, unsigned disable);
-
 #endif /* __ASM_ARCH_MSM_GPIO_H */

arch/arm/mach-msm/include/mach/io.h

@@ -28,6 +28,7 @@ void __iomem *__msm_ioremap(unsigned long phys_addr, size_t size, unsigned int m
 
 void msm_map_qsd8x50_io(void);
 void msm_map_msm7x30_io(void);
+void msm_map_msm8x60_io(void);
 
 extern unsigned int msm_shared_ram_phys;
 

arch/arm/mach-msm/include/mach/iommu.h

+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+
+#ifndef MSM_IOMMU_H
+#define MSM_IOMMU_H
+
+#include <linux/interrupt.h>
+
+/* Maximum number of Machine IDs that we are allowing to be mapped to the same
+ * context bank. The number of MIDs mapped to the same CB does not affect
+ * performance, but there is a practical limit on how many distinct MIDs may
+ * be present. These mappings are typically determined at design time and are
+ * not expected to change at run time.
+ */
+#define MAX_NUM_MIDS	16
+
+/**
+ * struct msm_iommu_dev - a single IOMMU hardware instance
+ * name		Human-readable name given to this IOMMU HW instance
+ * clk_rate	Rate to set for this IOMMU's clock, if applicable to this
+ *		particular IOMMU. 0 means don't set a rate.
+ *		-1 means it is an AXI clock with no valid rate
+ *
+ */
+struct msm_iommu_dev {
+	const char *name;
+	int clk_rate;
+};
+
+/**
+ * struct msm_iommu_ctx_dev - an IOMMU context bank instance
+ * name		Human-readable name given to this context bank
+ * num		Index of this context bank within the hardware
+ * mids		List of Machine IDs that are to be mapped into this context
+ *		bank, terminated by -1. The MID is a set of signals on the
+ *		AXI bus that identifies the function associated with a specific
+ *		memory request. (See ARM spec).
+ */
+struct msm_iommu_ctx_dev {
+	const char *name;
+	int num;
+	int mids[MAX_NUM_MIDS];
+};
+
+
+/**
+ * struct msm_iommu_drvdata - A single IOMMU hardware instance
+ * @base:	IOMMU config port base address (VA)
+ * @irq:	Interrupt number
+  *
+ * A msm_iommu_drvdata holds the global driver data about a single piece
+ * of an IOMMU hardware instance.
+ */
+struct msm_iommu_drvdata {
+	void __iomem *base;
+	int irq;
+};
+
+/**
+ * struct msm_iommu_ctx_drvdata - an IOMMU context bank instance
+ * @num:		Hardware context number of this context
+ * @pdev:		Platform device associated wit this HW instance
+ * @attached_elm:	List element for domains to track which devices are
+ *			attached to them
+ *
+ * A msm_iommu_ctx_drvdata holds the driver data for a single context bank
+ * within each IOMMU hardware instance
+ */
+struct msm_iommu_ctx_drvdata {
+	int num;
+	struct platform_device *pdev;
+	struct list_head attached_elm;
+};
+
+/*
+ * Look up an IOMMU context device by its context name. NULL if none found.
+ * Useful for testing and drivers that do not yet fully have IOMMU stuff in
+ * their platform devices.
+ */
+struct device *msm_iommu_get_ctx(const char *ctx_name);
+
+/*
+ * Interrupt handler for the IOMMU context fault interrupt. Hooking the
+ * interrupt is not supported in the API yet, but this will print an error
+ * message and dump useful IOMMU registers.
+ */
+irqreturn_t msm_iommu_fault_handler(int irq, void *dev_id);
+
+#endif

arch/arm/mach-msm/include/mach/irqs.h

@@ -24,6 +24,8 @@
 #elif defined(CONFIG_ARCH_QSD8X50)
 #include "irqs-8x50.h"
 #include "sirc.h"
+#elif defined(CONFIG_ARCH_MSM8X60)
+#include "irqs-8x60.h"
 #elif defined(CONFIG_ARCH_MSM_ARM11)
 #include "irqs-7x00.h"
 #else