ARM: dts: qcom-msm8974-fp2: Use &labels

Use &labels to align with the style used in new DTS and apply tiny
style fixes.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Rebased on top of Krzysztof underscore fixes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415115633.575010-10-konrad.dybcio@somainline.org

arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts

@@ -5,7 +5,6 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
-
 / {
 	model = "Fairphone 2";
 	compatible = "fairphone,fp2", "qcom,msm8974";
@@ -54,22 +53,89 @@ vibrator {
 		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
 		vcc-supply = <&pm8941_l18>;
 	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&imem {
+	status = "okay";
+
+	reboot-mode {
+		mode-normal	= <0x77665501>;
+		mode-bootloader	= <0x77665500>;
+		mode-recovery	= <0x77665502>;
+	};
+};
+
+&otg {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	ulpi {
+		phy@a {
+			status = "okay";
+
+			v1p8-supply = <&pm8941_l6>;
+			v3p3-supply = <&pm8941_l24>;
+
+			extcon = <&smbb>;
+			qcom,init-seq = /bits/ 8 <0x1 0x64>;
+		};
+	};
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active {
+		pins = "gpio1", "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pronto {
+	status = "okay";
+
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
 
-	smd {
-		rpm {
-			rpm-requests {
+&rpm_requests {
 	pm8841-regulators {
-					s1 {
+		pm8841_s1: s1 {
 			regulator-min-microvolt = <675000>;
 			regulator-max-microvolt = <1050000>;
 		};
 
-					s2 {
+		pm8841_s2: s2 {
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1050000>;
 		};
 
-					s3 {
+		pm8841_s3: s3 {
 			regulator-min-microvolt = <1050000>;
 			regulator-max-microvolt = <1050000>;
 		};
@@ -85,199 +151,181 @@ pm8941-regulators {
 		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
 		vdd_l21-supply = <&vreg_boost>;
 
-					s1 {
+		pm8941_s1: s1 {
 			regulator-min-microvolt = <1300000>;
 			regulator-max-microvolt = <1300000>;
-
 			regulator-always-on;
 			regulator-boot-on;
 		};
 
-					s2 {
+		pm8941_s2: s2 {
 			regulator-min-microvolt = <2150000>;
 			regulator-max-microvolt = <2150000>;
-
 			regulator-boot-on;
 		};
 
-					s3 {
+		pm8941_s3: s3 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
-
 			regulator-always-on;
 			regulator-boot-on;
 		};
 
-					l1 {
+		pm8941_l1: l1 {
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
-
 			regulator-always-on;
 			regulator-boot-on;
 		};
 
-					l2 {
+		pm8941_l2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 		};
 
-					l3 {
+		pm8941_l3: l3 {
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
 		};
 
-					l4 {
+		pm8941_l4: l4 {
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1225000>;
 		};
 
-					l5 {
+		pm8941_l5: l5 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
 
-					l6 {
+		pm8941_l6: l6 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
-
 			regulator-boot-on;
 		};
 
-					l7 {
+		pm8941_l7: l7 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
-
 			regulator-boot-on;
 		};
 
-					l8 {
+		pm8941_l8: l8 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
 
-					l9 {
+		pm8941_l9: l9 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2950000>;
 		};
 
-					l10 {
+		pm8941_l10: l10 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2950000>;
 		};
 
-					l11 {
+		pm8941_l11: l11 {
 			regulator-min-microvolt = <1225000>;
 			regulator-max-microvolt = <1350000>;
 		};
 
-					l12 {
+		pm8941_l12: l12 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
-
 			regulator-always-on;
 			regulator-boot-on;
 		};
 
-					l13 {
+		pm8941_l13: l13 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2950000>;
-
 			regulator-boot-on;
 		};
 
-					l14 {
+		pm8941_l14: l14 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
 
-					l15 {
+		pm8941_l15: l15 {
 			regulator-min-microvolt = <2050000>;
 			regulator-max-microvolt = <2050000>;
 		};
 
-					l16 {
+		pm8941_l16: l16 {
 			regulator-min-microvolt = <2700000>;
 			regulator-max-microvolt = <2700000>;
 		};
 
-					l17 {
+		pm8941_l17: l17 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 		};
 
-					l18 {
+		pm8941_l18: l18 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 		};
 
-					l19 {
+		pm8941_l19: l19 {
 			regulator-min-microvolt = <2900000>;
 			regulator-max-microvolt = <3350000>;
 		};
 
-					l20 {
+		pm8941_l20: l20 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
 			regulator-system-load = <200000>;
 			regulator-allow-set-load;
+			regulator-boot-on;
 		};
 
-					l21 {
+		pm8941_l21: l21 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
-
 			regulator-boot-on;
 		};
 
-					l22 {
+		pm8941_l22: l22 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3300000>;
 		};
 
-					l23 {
+		pm8941_l23: l23 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
 		};
 
-					l24 {
+		pm8941_l24: l24 {
 			regulator-min-microvolt = <3075000>;
 			regulator-max-microvolt = <3075000>;
-
 			regulator-boot-on;
 		};
 	};
-			};
-		};
-	};
 };
 
-&soc {
-	serial@f991e000 {
-		status = "okay";
-	};
-
-	remoteproc@fb21b000 {
+&sdhc_1 {
 	status = "okay";
 
-		vddmx-supply = <&pm8841_s1>;
-		vddcx-supply = <&pm8841_s2>;
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
 
 	pinctrl-names = "default";
-		pinctrl-0 = <&wcnss_pin_a>;
-
-		smd-edge {
-			qcom,remote-pid = <4>;
-			label = "pronto";
+	pinctrl-0 = <&sdhc1_pin_a>;
+};
 
-			wcnss {
+&sdhc_2 {
 	status = "okay";
-			};
-		};
-	};
 
-	pinctrl@fd510000 {
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhc2_pin_a>;
+};
+
+&tlmm {
 	sdhc1_pin_a: sdhc1-pin-active {
 		clk {
 			pins = "sdc1_clk";
@@ -331,79 +379,4 @@ fm {
 			bias-pull-down;
 		};
 	};
-	};
-
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		bus-width = <4>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	imem@fe805000 {
-		status = "okay";
-
-		reboot-mode {
-			mode-normal	= <0x77665501>;
-			mode-bootloader	= <0x77665500>;
-			mode-recovery	= <0x77665502>;
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio1", "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-	};
 };

arch/arm/boot/dts/qcom-msm8974.dtsi

@@ -1590,7 +1590,7 @@ dsi0_phy: dsi-phy@fd922a00 {
 			};
 		};
 
-		imem@fe805000 {
+		imem: imem@fe805000 {
 			status = "disabled";
 			compatible = "syscon", "simple-mfd";
 			reg = <0xfe805000 0x1000>;