Commit 48c926cd authored by Marco Franchi's avatar Marco Franchi Committed by Rob Herring

dt-bindings: Remove leading zeros from bindings notation

Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`

Some unnecessary changes were manually fixed.
Signed-off-by: default avatarMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: default avatarRob Herring <robh@kernel.org>
parent efb5b43a
...@@ -62,7 +62,7 @@ pmu_system_controller: system-controller@10040000 { ...@@ -62,7 +62,7 @@ pmu_system_controller: system-controller@10040000 {
Example of clock consumer : Example of clock consumer :
usb3503: usb3503@08 { usb3503: usb3503@8 {
/* ... */ /* ... */
clock-names = "refclk"; clock-names = "refclk";
clocks = <&pmu_system_controller 0>; clocks = <&pmu_system_controller 0>;
......
...@@ -71,7 +71,7 @@ Optional nodes: ...@@ -71,7 +71,7 @@ Optional nodes:
- compatible: only "samsung,secure-firmware" is currently supported - compatible: only "samsung,secure-firmware" is currently supported
- reg: address of non-secure SYSRAM used for communication with firmware - reg: address of non-secure SYSRAM used for communication with firmware
firmware@0203F000 { firmware@203F000 {
compatible = "samsung,secure-firmware"; compatible = "samsung,secure-firmware";
reg = <0x0203F000 0x1000>; reg = <0x0203F000 0x1000>;
}; };
...@@ -33,7 +33,7 @@ Required properties: ...@@ -33,7 +33,7 @@ Required properties:
property with the highest frequency property with the highest frequency
Example: Example:
v2m_sysctl: sysctl@020000 { v2m_sysctl: sysctl@20000 {
compatible = "arm,sp810", "arm,primecell"; compatible = "arm,sp810", "arm,primecell";
reg = <0x020000 0x1000>; reg = <0x020000 0x1000>;
clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
......
...@@ -37,7 +37,7 @@ Example: ...@@ -37,7 +37,7 @@ Example:
compatible = "arm,vexpress-sysreg"; compatible = "arm,vexpress-sysreg";
reg = <0x10000000 0x1000>; reg = <0x10000000 0x1000>;
v2m_led_gpios: sys_led@08 { v2m_led_gpios: sys_led@8 {
compatible = "arm,vexpress-sysreg,sys_led"; compatible = "arm,vexpress-sysreg,sys_led";
gpio-controller; gpio-controller;
#gpio-cells = <2>; #gpio-cells = <2>;
......
...@@ -56,7 +56,7 @@ Examples: ...@@ -56,7 +56,7 @@ Examples:
interrupts = <115>; interrupts = <115>;
}; };
ahci: sata@01c18000 { ahci: sata@1c18000 {
compatible = "allwinner,sun4i-a10-ahci"; compatible = "allwinner,sun4i-a10-ahci";
reg = <0x01c18000 0x1000>; reg = <0x01c18000 0x1000>;
interrupts = <56>; interrupts = <56>;
......
...@@ -25,7 +25,7 @@ Optional properties: ...@@ -25,7 +25,7 @@ Optional properties:
Examples: Examples:
sata@02200000 { sata@2200000 {
compatible = "fsl,imx6q-ahci"; compatible = "fsl,imx6q-ahci";
reg = <0x02200000 0x4000>; reg = <0x02200000 0x4000>;
interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
......
...@@ -61,7 +61,7 @@ Timing property for child nodes. It is mandatory, not optional. ...@@ -61,7 +61,7 @@ Timing property for child nodes. It is mandatory, not optional.
Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM: Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
weim: weim@021b8000 { weim: weim@21b8000 {
compatible = "fsl,imx6q-weim"; compatible = "fsl,imx6q-weim";
reg = <0x021b8000 0x4000>; reg = <0x021b8000 0x4000>;
clocks = <&clks 196>; clocks = <&clks 196>;
......
...@@ -28,7 +28,7 @@ which can normally be found in the datasheet. ...@@ -28,7 +28,7 @@ which can normally be found in the datasheet.
Example: Example:
rsb@01f03400 { rsb@1f03400 {
compatible = "allwinner,sun8i-a23-rsb"; compatible = "allwinner,sun8i-a23-rsb";
reg = <0x01f03400 0x400>; reg = <0x01f03400 0x400>;
interrupts = <0 39 4>; interrupts = <0 39 4>;
......
...@@ -59,7 +59,7 @@ syscon: syscon@10000000 { ...@@ -59,7 +59,7 @@ syscon: syscon@10000000 {
compatible = "syscon"; compatible = "syscon";
reg = <0x10000000 0x1000>; reg = <0x10000000 0x1000>;
oscclk0: osc0@0c { oscclk0: osc0@c {
compatible = "arm,syscon-icst307"; compatible = "arm,syscon-icst307";
#clock-cells = <0>; #clock-cells = <0>;
lock-offset = <0x20>; lock-offset = <0x20>;
......
...@@ -80,7 +80,7 @@ Example 3: I2S controller node that consumes the clock generated by the clock ...@@ -80,7 +80,7 @@ Example 3: I2S controller node that consumes the clock generated by the clock
controller. Refer to the standard clock bindings for information controller. Refer to the standard clock bindings for information
about 'clocks' and 'clock-names' property. about 'clocks' and 'clock-names' property.
i2s0: i2s@03830000 { i2s0: i2s@3830000 {
compatible = "samsung,i2s-v5"; compatible = "samsung,i2s-v5";
reg = <0x03830000 0x100>; reg = <0x03830000 0x100>;
dmas = <&pdma0 10 dmas = <&pdma0 10
......
...@@ -43,7 +43,7 @@ Example: I2S controller node that consumes the clock generated by the clock ...@@ -43,7 +43,7 @@ Example: I2S controller node that consumes the clock generated by the clock
controller. Refer to the standard clock bindings for information controller. Refer to the standard clock bindings for information
about 'clocks' and 'clock-names' property. about 'clocks' and 'clock-names' property.
i2s0: i2s@03830000 { i2s0: i2s@3830000 {
/* ... */ /* ... */
clock-names = "iis", "i2s_opclk0", clock-names = "iis", "i2s_opclk0",
"i2s_opclk1"; "i2s_opclk1";
......
...@@ -21,7 +21,7 @@ Required properties: ...@@ -21,7 +21,7 @@ Required properties:
a size of 8. a size of 8.
- #clock-cells : from common clock binding; shall be set to 1 - #clock-cells : from common clock binding; shall be set to 1
divider_clk: core-clock@0064 { divider_clk: core-clock@64 {
compatible = "marvell,dove-divider-clock"; compatible = "marvell,dove-divider-clock";
reg = <0x0064 0x8>; reg = <0x0064 0x8>;
#clock-cells = <1>; #clock-cells = <1>;
......
...@@ -10,13 +10,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx1-clock.h ...@@ -10,13 +10,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx1-clock.h
for the full list of i.MX1 clock IDs. for the full list of i.MX1 clock IDs.
Examples: Examples:
clks: ccm@0021b000 { clks: ccm@21b000 {
#clock-cells = <1>; #clock-cells = <1>;
compatible = "fsl,imx1-ccm"; compatible = "fsl,imx1-ccm";
reg = <0x0021b000 0x1000>; reg = <0x0021b000 0x1000>;
}; };
pwm: pwm@00208000 { pwm: pwm@208000 {
#pwm-cells = <2>; #pwm-cells = <2>;
compatible = "fsl,imx1-pwm"; compatible = "fsl,imx1-pwm";
reg = <0x00208000 0x1000>; reg = <0x00208000 0x1000>;
......
...@@ -14,14 +14,14 @@ Examples: ...@@ -14,14 +14,14 @@ Examples:
#include <dt-bindings/clock/imx6qdl-clock.h> #include <dt-bindings/clock/imx6qdl-clock.h>
clks: ccm@020c4000 { clks: ccm@20c4000 {
compatible = "fsl,imx6q-ccm"; compatible = "fsl,imx6q-ccm";
reg = <0x020c4000 0x4000>; reg = <0x020c4000 0x4000>;
interrupts = <0 87 0x04 0 88 0x04>; interrupts = <0 87 0x04 0 88 0x04>;
#clock-cells = <1>; #clock-cells = <1>;
}; };
uart1: serial@02020000 { uart1: serial@2020000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x02020000 0x4000>; reg = <0x02020000 0x4000>;
interrupts = <0 26 0x04>; interrupts = <0 26 0x04>;
......
...@@ -46,7 +46,7 @@ Example: ...@@ -46,7 +46,7 @@ Example:
/* ... */ /* ... */
Node of the MFD chip Node of the MFD chip
max77686: max77686@09 { max77686: max77686@9 {
compatible = "maxim,max77686"; compatible = "maxim,max77686";
interrupt-parent = <&wakeup_eint>; interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>; interrupts = <26 0>;
...@@ -71,7 +71,7 @@ Example: ...@@ -71,7 +71,7 @@ Example:
/* ... */ /* ... */
Node of the MFD chip Node of the MFD chip
max77802: max77802@09 { max77802: max77802@9 {
compatible = "maxim,max77802"; compatible = "maxim,max77802";
interrupt-parent = <&wakeup_eint>; interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>; interrupts = <26 0>;
......
...@@ -42,7 +42,7 @@ Required properties: ...@@ -42,7 +42,7 @@ Required properties:
Example: Example:
clockgen-a@090ff000 { clockgen-a@90ff000 {
compatible = "st,clkgen-c32"; compatible = "st,clkgen-c32";
reg = <0x90ff000 0x1000>; reg = <0x90ff000 0x1000>;
......
...@@ -36,7 +36,7 @@ For the PRCM CCUs on A83T/H3/A64, two more clocks are needed: ...@@ -36,7 +36,7 @@ For the PRCM CCUs on A83T/H3/A64, two more clocks are needed:
- "iosc": the SoC's internal frequency oscillator - "iosc": the SoC's internal frequency oscillator
Example for generic CCU: Example for generic CCU:
ccu: clock@01c20000 { ccu: clock@1c20000 {
compatible = "allwinner,sun8i-h3-ccu"; compatible = "allwinner,sun8i-h3-ccu";
reg = <0x01c20000 0x400>; reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>; clocks = <&osc24M>, <&osc32k>;
...@@ -46,7 +46,7 @@ ccu: clock@01c20000 { ...@@ -46,7 +46,7 @@ ccu: clock@01c20000 {
}; };
Example for PRCM CCU: Example for PRCM CCU:
r_ccu: clock@01f01400 { r_ccu: clock@1f01400 {
compatible = "allwinner,sun50i-a64-r-ccu"; compatible = "allwinner,sun50i-a64-r-ccu";
reg = <0x01f01400 0x100>; reg = <0x01f01400 0x100>;
clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>; clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>;
......
...@@ -137,7 +137,7 @@ the address block, which is related to the overall mmc block. ...@@ -137,7 +137,7 @@ the address block, which is related to the overall mmc block.
For example: For example:
osc24M: clk@01c20050 { osc24M: clk@1c20050 {
#clock-cells = <0>; #clock-cells = <0>;
compatible = "allwinner,sun4i-a10-osc-clk"; compatible = "allwinner,sun4i-a10-osc-clk";
reg = <0x01c20050 0x4>; reg = <0x01c20050 0x4>;
...@@ -145,7 +145,7 @@ osc24M: clk@01c20050 { ...@@ -145,7 +145,7 @@ osc24M: clk@01c20050 {
clock-output-names = "osc24M"; clock-output-names = "osc24M";
}; };
pll1: clk@01c20000 { pll1: clk@1c20000 {
#clock-cells = <0>; #clock-cells = <0>;
compatible = "allwinner,sun4i-a10-pll1-clk"; compatible = "allwinner,sun4i-a10-pll1-clk";
reg = <0x01c20000 0x4>; reg = <0x01c20000 0x4>;
...@@ -153,7 +153,7 @@ pll1: clk@01c20000 { ...@@ -153,7 +153,7 @@ pll1: clk@01c20000 {
clock-output-names = "pll1"; clock-output-names = "pll1";
}; };
pll5: clk@01c20020 { pll5: clk@1c20020 {
#clock-cells = <1>; #clock-cells = <1>;
compatible = "allwinner,sun4i-pll5-clk"; compatible = "allwinner,sun4i-pll5-clk";
reg = <0x01c20020 0x4>; reg = <0x01c20020 0x4>;
...@@ -161,7 +161,7 @@ pll5: clk@01c20020 { ...@@ -161,7 +161,7 @@ pll5: clk@01c20020 {
clock-output-names = "pll5_ddr", "pll5_other"; clock-output-names = "pll5_ddr", "pll5_other";
}; };
pll6: clk@01c20028 { pll6: clk@1c20028 {
#clock-cells = <1>; #clock-cells = <1>;
compatible = "allwinner,sun6i-a31-pll6-clk"; compatible = "allwinner,sun6i-a31-pll6-clk";
reg = <0x01c20028 0x4>; reg = <0x01c20028 0x4>;
...@@ -169,7 +169,7 @@ pll6: clk@01c20028 { ...@@ -169,7 +169,7 @@ pll6: clk@01c20028 {
clock-output-names = "pll6", "pll6x2"; clock-output-names = "pll6", "pll6x2";
}; };
cpu: cpu@01c20054 { cpu: cpu@1c20054 {
#clock-cells = <0>; #clock-cells = <0>;
compatible = "allwinner,sun4i-a10-cpu-clk"; compatible = "allwinner,sun4i-a10-cpu-clk";
reg = <0x01c20054 0x4>; reg = <0x01c20054 0x4>;
...@@ -177,7 +177,7 @@ cpu: cpu@01c20054 { ...@@ -177,7 +177,7 @@ cpu: cpu@01c20054 {
clock-output-names = "cpu"; clock-output-names = "cpu";
}; };
mmc0_clk: clk@01c20088 { mmc0_clk: clk@1c20088 {
#clock-cells = <1>; #clock-cells = <1>;
compatible = "allwinner,sun4i-a10-mmc-clk"; compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20088 0x4>; reg = <0x01c20088 0x4>;
...@@ -199,7 +199,7 @@ gmac_int_tx_clk: clk@3 { ...@@ -199,7 +199,7 @@ gmac_int_tx_clk: clk@3 {
clock-output-names = "gmac_int_tx"; clock-output-names = "gmac_int_tx";
}; };
gmac_clk: clk@01c20164 { gmac_clk: clk@1c20164 {
#clock-cells = <0>; #clock-cells = <0>;
compatible = "allwinner,sun7i-a20-gmac-clk"; compatible = "allwinner,sun7i-a20-gmac-clk";
reg = <0x01c20164 0x4>; reg = <0x01c20164 0x4>;
...@@ -211,7 +211,7 @@ gmac_clk: clk@01c20164 { ...@@ -211,7 +211,7 @@ gmac_clk: clk@01c20164 {
clock-output-names = "gmac"; clock-output-names = "gmac";
}; };
mmc_config_clk: clk@01c13000 { mmc_config_clk: clk@1c13000 {
compatible = "allwinner,sun9i-a80-mmc-config-clk"; compatible = "allwinner,sun9i-a80-mmc-config-clk";
reg = <0x01c13000 0x10>; reg = <0x01c13000 0x10>;
clocks = <&ahb0_gates 8>; clocks = <&ahb0_gates 8>;
......
...@@ -25,7 +25,7 @@ Example: ...@@ -25,7 +25,7 @@ Example:
}; };
}; };
... ...
i2c0: i2c-master@0d090000 { i2c0: i2c-master@d090000 {
... ...
cdce706: clock-synth@69 { cdce706: clock-synth@69 {
compatible = "ti,cdce706"; compatible = "ti,cdce706";
......
...@@ -14,7 +14,7 @@ Optional properties: ...@@ -14,7 +14,7 @@ Optional properties:
- reset-names : must contain "ahb" - reset-names : must contain "ahb"
Example: Example:
crypto: crypto-engine@01c15000 { crypto: crypto-engine@1c15000 {
compatible = "allwinner,sun4i-a10-crypto"; compatible = "allwinner,sun4i-a10-crypto";
reg = <0x01c15000 0x1000>; reg = <0x01c15000 0x1000>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
......
...@@ -42,7 +42,7 @@ Optional properties: ...@@ -42,7 +42,7 @@ Optional properties:
example: example:
gpu_3d: gpu@00130000 { gpu_3d: gpu@130000 {
compatible = "vivante,gc"; compatible = "vivante,gc";
reg = <0x00130000 0x4000>; reg = <0x00130000 0x4000>;
interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>;
......
...@@ -32,11 +32,11 @@ Optional properties ...@@ -32,11 +32,11 @@ Optional properties
Example: Example:
gpr: iomuxc-gpr@020e0000 { gpr: iomuxc-gpr@20e0000 {
/* ... */ /* ... */
}; };
hdmi: hdmi@0120000 { hdmi: hdmi@120000 {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <0>; #size-cells = <0>;
compatible = "fsl,imx6q-hdmi"; compatible = "fsl,imx6q-hdmi";
......
...@@ -78,7 +78,7 @@ chosen { ...@@ -78,7 +78,7 @@ chosen {
stdout-path = "display0"; stdout-path = "display0";
}; };
soc@01c00000 { soc@1c00000 {
lcdc0: lcdc@1c0c000 { lcdc0: lcdc@1c0c000 {
compatible = "allwinner,sun4i-a10-lcdc"; compatible = "allwinner,sun4i-a10-lcdc";
... ...
......
...@@ -266,7 +266,7 @@ connector { ...@@ -266,7 +266,7 @@ connector {
}; };
}; };
hdmi: hdmi@01c16000 { hdmi: hdmi@1c16000 {
compatible = "allwinner,sun5i-a10s-hdmi"; compatible = "allwinner,sun5i-a10s-hdmi";
reg = <0x01c16000 0x1000>; reg = <0x01c16000 0x1000>;
interrupts = <58>; interrupts = <58>;
...@@ -305,7 +305,7 @@ hdmi: hdmi@01c16000 { ...@@ -305,7 +305,7 @@ hdmi: hdmi@01c16000 {
}; };
}; };
tve0: tv-encoder@01c0a000 { tve0: tv-encoder@1c0a000 {
compatible = "allwinner,sun4i-a10-tv-encoder"; compatible = "allwinner,sun4i-a10-tv-encoder";
reg = <0x01c0a000 0x1000>; reg = <0x01c0a000 0x1000>;
clocks = <&ahb_gates 34>; clocks = <&ahb_gates 34>;
......
...@@ -12,7 +12,7 @@ Required properties: ...@@ -12,7 +12,7 @@ Required properties:
second cell holding the request line number. second cell holding the request line number.
Example: Example:
dma: dma-controller@01c02000 { dma: dma-controller@1c02000 {
compatible = "allwinner,sun4i-a10-dma"; compatible = "allwinner,sun4i-a10-dma";
reg = <0x01c02000 0x1000>; reg = <0x01c02000 0x1000>;
interrupts = <27>; interrupts = <27>;
...@@ -32,7 +32,7 @@ The three cells in order are: ...@@ -32,7 +32,7 @@ The three cells in order are:
3. The port ID as specified in the datasheet 3. The port ID as specified in the datasheet
Example: Example:
spi2: spi@01c17000 { spi2: spi@1c17000 {
compatible = "allwinner,sun4i-a10-spi"; compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>; reg = <0x01c17000 0x1000>;
interrupts = <0 12 4>; interrupts = <0 12 4>;
......
...@@ -38,7 +38,7 @@ The two cells in order are: ...@@ -38,7 +38,7 @@ The two cells in order are:
2. The port ID as specified in the datasheet 2. The port ID as specified in the datasheet
Example: Example:
spi2: spi@01c6a000 { spi2: spi@1c6a000 {
compatible = "allwinner,sun6i-a31-spi"; compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c6a000 0x1000>; reg = <0x01c6a000 0x1000>;
interrupts = <0 67 4>; interrupts = <0 67 4>;
......
...@@ -142,7 +142,7 @@ mcasp0: mcasp@48038000 { ...@@ -142,7 +142,7 @@ mcasp0: mcasp@48038000 {
}; };
2. 2.
edma1: edma@02728000 { edma1: edma@2728000 {
compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc"; compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
reg = <0x02728000 0x8000>; reg = <0x02728000 0x8000>;
reg-names = "edma3_cc"; reg-names = "edma3_cc";
...@@ -165,13 +165,13 @@ edma1: edma@02728000 { ...@@ -165,13 +165,13 @@ edma1: edma@02728000 {
power-domains = <&k2g_pds 0x4f>; power-domains = <&k2g_pds 0x4f>;
}; };
edma1_tptc0: tptc@027b0000 { edma1_tptc0: tptc@27b0000 {
compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc"; compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
reg = <0x027b0000 0x400>; reg = <0x027b0000 0x400>;
power-domains = <&k2g_pds 0x4f>; power-domains = <&k2g_pds 0x4f>;
}; };
edma1_tptc1: tptc@027b8000 { edma1_tptc1: tptc@27b8000 {
compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc"; compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc";
reg = <0x027b8000 0x400>; reg = <0x027b8000 0x400>;
power-domains = <&k2g_pds 0x4f>; power-domains = <&k2g_pds 0x4f>;
......
...@@ -26,7 +26,7 @@ Controller: ...@@ -26,7 +26,7 @@ Controller:
Client: Client:
Use specific request line passing from dmax Use specific request line passing from dmax
For example, spdif0 tx channel request line is 4 For example, spdif0 tx channel request line is 4
spdif0: spdif0@0b004000 { spdif0: spdif0@b004000 {
#sound-dai-cells = <0>; #sound-dai-cells = <0>;
compatible = "zte,zx296702-spdif"; compatible = "zte,zx296702-spdif";
reg = <0x0b004000 0x1000>; reg = <0x0b004000 0x1000>;
......
...@@ -66,7 +66,7 @@ See ".../sram/sram.txt" for the bindings. ...@@ -66,7 +66,7 @@ See ".../sram/sram.txt" for the bindings.
Example: Example:
hsp_top0: hsp@03c00000 { hsp_top0: hsp@3c00000 {
... ...
#mbox-cells = <2>; #mbox-cells = <2>;
}; };
......
...@@ -25,7 +25,7 @@ Please refer to gpio.txt in this directory for details of the common GPIO ...@@ -25,7 +25,7 @@ Please refer to gpio.txt in this directory for details of the common GPIO
bindings used by client devices. bindings used by client devices.
Example: Example:
dspgpio0: keystone_dsp_gpio@02620240 { dspgpio0: keystone_dsp_gpio@2620240 {
compatible = "ti,keystone-dsp-gpio"; compatible = "ti,keystone-dsp-gpio";
ti,syscon-dev = <&devctrl 0x240>; ti,syscon-dev = <&devctrl 0x240>;
gpio-controller; gpio-controller;
......
...@@ -30,7 +30,7 @@ Optional properties: ...@@ -30,7 +30,7 @@ Optional properties:
Example: Example:
pdc_gpios: gpio-controller@02006500 { pdc_gpios: gpio-controller@2006500 {
gpio-controller; gpio-controller;
#gpio-cells = <2>; #gpio-cells = <2>;
......
...@@ -59,7 +59,7 @@ Required properties: ...@@ -59,7 +59,7 @@ Required properties:
Example: Example:
gpios: gpio-controller@02005800 { gpios: gpio-controller@2005800 {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <0>; #size-cells = <0>;
compatible = "img,tz1090-gpio"; compatible = "img,tz1090-gpio";
......
...@@ -17,7 +17,7 @@ Optional properties : ...@@ -17,7 +17,7 @@ Optional properties :
Example : Example :
i2c@02010084000 { i2c@2010084000 {
compatible = "lsi,api2c"; compatible = "lsi,api2c";
device_type = "i2c"; device_type = "i2c";
#address-cells = <1>; #address-cells = <1>;
......
...@@ -24,7 +24,7 @@ Slave device properties: ...@@ -24,7 +24,7 @@ Slave device properties:
Example: Example:
p2wi@01f03400 { p2wi@1f03400 {
compatible = "allwinner,sun6i-a31-p2wi"; compatible = "allwinner,sun6i-a31-p2wi";
reg = <0x01f03400 0x400>; reg = <0x01f03400 0x400>;
interrupts = <0 39 4>; interrupts = <0 39 4>;
......
...@@ -19,7 +19,7 @@ Optional properties: ...@@ -19,7 +19,7 @@ Optional properties:
Example: Example:
ak8974@0f { ak8974@f {
compatible = "asahi-kasei,ak8974"; compatible = "asahi-kasei,ak8974";
reg = <0x0f>; reg = <0x0f>;
avdd-supply = <&foo_reg>; avdd-supply = <&foo_reg>;
......
...@@ -13,7 +13,7 @@ Optional properties: ...@@ -13,7 +13,7 @@ Optional properties:
Example: Example:
ak8975@0c { ak8975@c {
compatible = "asahi-kasei,ak8975"; compatible = "asahi-kasei,ak8975";
reg = <0x0c>; reg = <0x0c>;
gpios = <&gpj0 7 0>; gpios = <&gpj0 7 0>;
......
...@@ -19,7 +19,7 @@ Example: ...@@ -19,7 +19,7 @@ Example:
#include <dt-bindings/input/input.h> #include <dt-bindings/input/input.h>
lradc: lradc@01c22800 { lradc: lradc@1c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys"; compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>; reg = <0x01c22800 0x100>;
interrupts = <31>; interrupts = <31>;
......
...@@ -10,7 +10,7 @@ Required properties: ...@@ -10,7 +10,7 @@ Required properties:
Example: Example:
egalax_ts@04 { touchscreen@4 {
compatible = "eeti,egalax_ts"; compatible = "eeti,egalax_ts";
reg = <0x04>; reg = <0x04>;
interrupt-parent = <&gpio1>; interrupt-parent = <&gpio1>;
......
...@@ -21,7 +21,7 @@ Optional properties: ...@@ -21,7 +21,7 @@ Optional properties:
each read. Valid values are 1, 4, 8, 16 and 32. each read. Valid values are 1, 4, 8, 16 and 32.
Example: Example:
tsc: tsc@02040000 { tsc: tsc@2040000 {
compatible = "fsl,imx6ul-tsc"; compatible = "fsl,imx6ul-tsc";
reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
......
...@@ -20,7 +20,7 @@ Required properties: ...@@ -20,7 +20,7 @@ Required properties:
Example: Example:
sc-nmi-intc@01c00030 { sc-nmi-intc@1c00030 {
compatible = "allwinner,sun7i-a20-sc-nmi"; compatible = "allwinner,sun7i-a20-sc-nmi";
interrupt-controller; interrupt-controller;
#interrupt-cells = <2>; #interrupt-cells = <2>;
......
...@@ -20,7 +20,7 @@ Please refer to interrupts.txt in this directory for details of the common ...@@ -20,7 +20,7 @@ Please refer to interrupts.txt in this directory for details of the common
Interrupt Controllers bindings used by client devices. Interrupt Controllers bindings used by client devices.
Example: Example:
kirq0: keystone_irq0@026202a0 { kirq0: keystone_irq0@26202a0 {
compatible = "ti,keystone-irq"; compatible = "ti,keystone-irq";
ti,syscon-dev = <&devctrl 0x2a0>; ti,syscon-dev = <&devctrl 0x2a0>;
interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>; interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
......
...@@ -115,7 +115,7 @@ to non-secure vs secure interrupt line. ...@@ -115,7 +115,7 @@ to non-secure vs secure interrupt line.
iommus = <&apps_iommu 4>; iommus = <&apps_iommu 4>;
}; };
gpu@01c00000 { gpu@1c00000 {
... ...
iommus = <&gpu_iommu 1>, <&gpu_iommu 2>; iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
}; };
...@@ -32,7 +32,7 @@ syscon: syscon@10000000 { ...@@ -32,7 +32,7 @@ syscon: syscon@10000000 {
compatible = "arm,realview-pb1176-syscon", "syscon"; compatible = "arm,realview-pb1176-syscon", "syscon";
reg = <0x10000000 0x1000>; reg = <0x10000000 0x1000>;
led@08.0 { led@8.0 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x01>; mask = <0x01>;
...@@ -40,7 +40,7 @@ syscon: syscon@10000000 { ...@@ -40,7 +40,7 @@ syscon: syscon@10000000 {
linux,default-trigger = "heartbeat"; linux,default-trigger = "heartbeat";
default-state = "on"; default-state = "on";
}; };
led@08.1 { led@8.1 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x02>; mask = <0x02>;
...@@ -48,7 +48,7 @@ syscon: syscon@10000000 { ...@@ -48,7 +48,7 @@ syscon: syscon@10000000 {
linux,default-trigger = "mmc0"; linux,default-trigger = "mmc0";
default-state = "off"; default-state = "off";
}; };
led@08.2 { led@8.2 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x04>; mask = <0x04>;
...@@ -56,35 +56,35 @@ syscon: syscon@10000000 { ...@@ -56,35 +56,35 @@ syscon: syscon@10000000 {
linux,default-trigger = "cpu0"; linux,default-trigger = "cpu0";
default-state = "off"; default-state = "off";
}; };
led@08.3 { led@8.3 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x08>; mask = <0x08>;
label = "versatile:3"; label = "versatile:3";
default-state = "off"; default-state = "off";
}; };
led@08.4 { led@8.4 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x10>; mask = <0x10>;
label = "versatile:4"; label = "versatile:4";
default-state = "off"; default-state = "off";
}; };
led@08.5 { led@8.5 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x20>; mask = <0x20>;
label = "versatile:5"; label = "versatile:5";
default-state = "off"; default-state = "off";
}; };
led@08.6 { led@8.6 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x40>; mask = <0x40>;
label = "versatile:6"; label = "versatile:6";
default-state = "off"; default-state = "off";
}; };
led@08.7 { led@8.7 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x80>; mask = <0x80>;
......
...@@ -29,7 +29,7 @@ Required properties: ...@@ -29,7 +29,7 @@ Required properties:
Example(K2G): Example(K2G):
------------ ------------
msgmgr: msgmgr@02a00000 { msgmgr: msgmgr@2a00000 {
compatible = "ti,k2g-message-manager"; compatible = "ti,k2g-message-manager";
#mbox-cells = <2>; #mbox-cells = <2>;
reg-names = "queue_proxy_region", "queue_state_debug_region"; reg-names = "queue_proxy_region", "queue_state_debug_region";
......
...@@ -446,7 +446,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd. ...@@ -446,7 +446,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
that services interrupts for this device. that services interrupts for this device.
Example Discovery CPU Error node: Example Discovery CPU Error node:
cpu-error@0070 { cpu-error@70 {
compatible = "marvell,mv64360-cpu-error"; compatible = "marvell,mv64360-cpu-error";
reg = <0x70 0x10 0x128 0x28>; reg = <0x70 0x10 0x128 0x28>;
interrupts = <3>; interrupts = <3>;
...@@ -466,7 +466,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd. ...@@ -466,7 +466,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
that services interrupts for this device. that services interrupts for this device.
Example Discovery SRAM Controller node: Example Discovery SRAM Controller node:
sram-ctrl@0380 { sram-ctrl@380 {
compatible = "marvell,mv64360-sram-ctrl"; compatible = "marvell,mv64360-sram-ctrl";
reg = <0x380 0x80>; reg = <0x380 0x80>;
interrupts = <13>; interrupts = <13>;
......
...@@ -27,7 +27,7 @@ Documentation/devicetree/bindings/media/video-interfaces.txt. ...@@ -27,7 +27,7 @@ Documentation/devicetree/bindings/media/video-interfaces.txt.
Example: Example:
tc358743@0f { tc358743@f {
compatible = "toshiba,tc358743"; compatible = "toshiba,tc358743";
reg = <0x0f>; reg = <0x0f>;
clocks = <&hdmi_osc>; clocks = <&hdmi_osc>;
......
...@@ -25,7 +25,7 @@ Optional properties: ...@@ -25,7 +25,7 @@ Optional properties:
Example: Example:
ir@02006200 { ir@2006200 {
compatible = "img,ir-rev1"; compatible = "img,ir-rev1";
reg = <0x02006200 0x100>; reg = <0x02006200 0x100>;
interrupts = <29 4>; interrupts = <29 4>;
......
...@@ -13,7 +13,7 @@ Required properties: ...@@ -13,7 +13,7 @@ Required properties:
Example for STIH407: Example for STIH407:
sti-cec@094a087c { sti-cec@94a087c {
compatible = "st,stih-cec"; compatible = "st,stih-cec";
reg = <0x94a087c 0x64>; reg = <0x94a087c 0x64>;
clocks = <&clk_sysin>; clocks = <&clk_sysin>;
......
...@@ -50,7 +50,7 @@ Example: ...@@ -50,7 +50,7 @@ Example:
/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */ /* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
c8sectpfe@08a20000 { c8sectpfe@8a20000 {
compatible = "st,stih407-c8sectpfe"; compatible = "st,stih407-c8sectpfe";
reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
reg-names = "stfe", "stfe-ram"; reg-names = "stfe", "stfe-ram";
......
...@@ -14,7 +14,7 @@ Optional properties: ...@@ -14,7 +14,7 @@ Optional properties:
Example: Example:
ir0: ir@01c21800 { ir0: ir@1c21800 {
compatible = "allwinner,sun4i-a10-ir"; compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 6>, <&ir0_clk>; clocks = <&apb0_gates 6>, <&ir0_clk>;
clock-names = "apb", "ir"; clock-names = "apb", "ir";
......
...@@ -19,7 +19,7 @@ Required properties: ...@@ -19,7 +19,7 @@ Required properties:
Example: Example:
max77686: pmic@09 { max77686: pmic@9 {
compatible = "maxim,max77686"; compatible = "maxim,max77686";
interrupt-parent = <&wakeup_eint>; interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>; interrupts = <26 0>;
......
...@@ -18,7 +18,7 @@ Required properties: ...@@ -18,7 +18,7 @@ Required properties:
Example: Example:
max77802: pmic@09 { max77802: pmic@9 {
compatible = "maxim,max77802"; compatible = "maxim,max77802";
interrupt-parent = <&intc>; interrupt-parent = <&intc>;
interrupts = <26 IRQ_TYPE_NONE>; interrupts = <26 IRQ_TYPE_NONE>;
......
...@@ -41,7 +41,7 @@ foo@1000 { ...@@ -41,7 +41,7 @@ foo@1000 {
compatible = "syscon", "simple-mfd"; compatible = "syscon", "simple-mfd";
reg = <0x01000 0x1000>; reg = <0x01000 0x1000>;
led@08.0 { led@8.0 {
compatible = "register-bit-led"; compatible = "register-bit-led";
offset = <0x08>; offset = <0x08>;
mask = <0x01>; mask = <0x01>;
......
...@@ -10,7 +10,7 @@ Required properties: ...@@ -10,7 +10,7 @@ Required properties:
- #io-channel-cells: shall be 0, - #io-channel-cells: shall be 0,
Example: Example:
ths: ths@01c25000 { ths: ths@1c25000 {
compatible = "allwinner,sun8i-a33-ths"; compatible = "allwinner,sun8i-a33-ths";
reg = <0x01c25000 0x100>; reg = <0x01c25000 0x100>;
#thermal-sensor-cells = <0>; #thermal-sensor-cells = <0>;
...@@ -47,7 +47,7 @@ Optional properties: ...@@ -47,7 +47,7 @@ Optional properties:
Example: Example:
rtp: rtp@01c25000 { rtp: rtp@1c25000 {
compatible = "allwinner,sun4i-a10-ts"; compatible = "allwinner,sun4i-a10-ts";
reg = <0x01c25000 0x100>; reg = <0x01c25000 0x100>;
interrupts = <29>; interrupts = <29>;
......
...@@ -15,7 +15,7 @@ The prcm node may contain several subdevices definitions: ...@@ -15,7 +15,7 @@ The prcm node may contain several subdevices definitions:
Example: Example:
prcm: prcm@01f01400 { prcm: prcm@1f01400 {
compatible = "allwinner,sun6i-a31-prcm"; compatible = "allwinner,sun6i-a31-prcm";
reg = <0x01f01400 0x200>; reg = <0x01f01400 0x200>;
......
...@@ -18,7 +18,7 @@ Optional property: ...@@ -18,7 +18,7 @@ Optional property:
performed on the device. performed on the device.
Examples: Examples:
gpr: iomuxc-gpr@020e0000 { gpr: iomuxc-gpr@20e0000 {
compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
reg = <0x020e0000 0x38>; reg = <0x020e0000 0x38>;
}; };
...@@ -143,7 +143,7 @@ sdhci@ab000000 { ...@@ -143,7 +143,7 @@ sdhci@ab000000 {
Example with sdio function subnode: Example with sdio function subnode:
mmc3: mmc@01c12000 { mmc3: mmc@1c12000 {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <0>; #size-cells = <0>;
......
...@@ -74,7 +74,7 @@ mmc0: sdhci@fe81e000 { ...@@ -74,7 +74,7 @@ mmc0: sdhci@fe81e000 {
/* Example SD stih407 family configuration */ /* Example SD stih407 family configuration */
mmc1: sdhci@09080000 { mmc1: sdhci@9080000 {
compatible = "st,sdhci-stih407", "st,sdhci"; compatible = "st,sdhci-stih407", "st,sdhci";
reg = <0x09080000 0x7ff>; reg = <0x09080000 0x7ff>;
reg-names = "mmc"; reg-names = "mmc";
...@@ -90,7 +90,7 @@ mmc1: sdhci@09080000 { ...@@ -90,7 +90,7 @@ mmc1: sdhci@09080000 {
/* Example eMMC stih407 family configuration */ /* Example eMMC stih407 family configuration */
mmc0: sdhci@09060000 { mmc0: sdhci@9060000 {
compatible = "st,sdhci-stih407", "st,sdhci"; compatible = "st,sdhci-stih407", "st,sdhci";
reg = <0x09060000 0x7ff>, <0x9061008 0x20>; reg = <0x09060000 0x7ff>, <0x9061008 0x20>;
reg-names = "mmc", "top-mmc-delay"; reg-names = "mmc", "top-mmc-delay";
......
...@@ -29,7 +29,7 @@ Optional properties: ...@@ -29,7 +29,7 @@ Optional properties:
Examples: Examples:
- Within .dtsi: - Within .dtsi:
mmc0: mmc@01c0f000 { mmc0: mmc@1c0f000 {
compatible = "allwinner,sun5i-a13-mmc"; compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>; reg = <0x01c0f000 0x1000>;
clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>; clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>;
...@@ -39,7 +39,7 @@ Examples: ...@@ -39,7 +39,7 @@ Examples:
}; };
- Within dts: - Within dts:
mmc0: mmc@01c0f000 { mmc0: mmc@1c0f000 {
pinctrl-names = "default", "default"; pinctrl-names = "default", "default";
pinctrl-0 = <&mmc0_pins_a>; pinctrl-0 = <&mmc0_pins_a>;
pinctrl-1 = <&mmc0_cd_pin_reference_design>; pinctrl-1 = <&mmc0_cd_pin_reference_design>;
......
...@@ -31,7 +31,7 @@ see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. ...@@ -31,7 +31,7 @@ see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings.
Examples: Examples:
nfc: nand@01c03000 { nfc: nand@1c03000 {
compatible = "allwinner,sun4i-a10-nand"; compatible = "allwinner,sun4i-a10-nand";
reg = <0x01c03000 0x1000>; reg = <0x01c03000 0x1000>;
interrupts = <0 37 1>; interrupts = <0 37 1>;
......
...@@ -10,7 +10,7 @@ Required properties: ...@@ -10,7 +10,7 @@ Required properties:
Example: Example:
emac: ethernet@01c0b000 { emac: ethernet@1c0b000 {
compatible = "allwinner,sun4i-a10-emac"; compatible = "allwinner,sun4i-a10-emac";
reg = <0x01c0b000 0x1000>; reg = <0x01c0b000 0x1000>;
interrupts = <55>; interrupts = <55>;
......
...@@ -9,7 +9,7 @@ Optional properties: ...@@ -9,7 +9,7 @@ Optional properties:
- phy-supply: phandle to a regulator if the PHY needs one - phy-supply: phandle to a regulator if the PHY needs one
Example at the SoC level: Example at the SoC level:
mdio@01c0b080 { mdio@1c0b080 {
compatible = "allwinner,sun4i-a10-mdio"; compatible = "allwinner,sun4i-a10-mdio";
reg = <0x01c0b080 0x14>; reg = <0x01c0b080 0x14>;
#address-cells = <1>; #address-cells = <1>;
...@@ -18,7 +18,7 @@ mdio@01c0b080 { ...@@ -18,7 +18,7 @@ mdio@01c0b080 {
And at the board level: And at the board level:
mdio@01c0b080 { mdio@1c0b080 {
phy-supply = <&reg_emac_3v3>; phy-supply = <&reg_emac_3v3>;
phy0: ethernet-phy@0 { phy0: ethernet-phy@0 {
......
...@@ -15,7 +15,7 @@ Optional properties: ...@@ -15,7 +15,7 @@ Optional properties:
Examples: Examples:
gmac: ethernet@01c50000 { gmac: ethernet@1c50000 {
compatible = "allwinner,sun7i-a20-gmac"; compatible = "allwinner,sun7i-a20-gmac";
reg = <0x01c50000 0x10000>, reg = <0x01c50000 0x10000>,
<0x01c20164 0x4>; <0x01c20164 0x4>;
......
...@@ -109,7 +109,7 @@ ethernet@f0ba0000 { ...@@ -109,7 +109,7 @@ ethernet@f0ba0000 {
reg = <0xf0ba0000 0xfc4c>; reg = <0xf0ba0000 0xfc4c>;
interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>; interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>;
mdio@0e14 { mdio@e14 {
compatible = "brcm,genet-mdio-v4"; compatible = "brcm,genet-mdio-v4";
#address-cells = <0x1>; #address-cells = <0x1>;
#size-cells = <0x0>; #size-cells = <0x0>;
......
...@@ -45,7 +45,7 @@ Required properties: ...@@ -45,7 +45,7 @@ Required properties:
Example: Example:
SoC dtsi: SoC dtsi:
m_can1: can@020e8000 { m_can1: can@20e8000 {
compatible = "bosch,m_can"; compatible = "bosch,m_can";
reg = <0x020e8000 0x4000>, <0x02298000 0x4000>; reg = <0x020e8000 0x4000>, <0x02298000 0x4000>;
reg-names = "m_can", "message_ram"; reg-names = "m_can", "message_ram";
......
...@@ -19,7 +19,7 @@ SoC common .dtsi file: ...@@ -19,7 +19,7 @@ SoC common .dtsi file:
allwinner,pull = <0>; allwinner,pull = <0>;
}; };
... ...
can0: can@01c2bc00 { can0: can@1c2bc00 {
compatible = "allwinner,sun4i-a10-can"; compatible = "allwinner,sun4i-a10-can";
reg = <0x01c2bc00 0x400>; reg = <0x01c2bc00 0x400>;
interrupts = <0 26 4>; interrupts = <0 26 4>;
...@@ -29,7 +29,7 @@ SoC common .dtsi file: ...@@ -29,7 +29,7 @@ SoC common .dtsi file:
Board specific .dts file: Board specific .dts file:
can0: can@01c2bc00 { can0: can@1c2bc00 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&can0_pins_a>; pinctrl-0 = <&can0_pins_a>;
status = "okay"; status = "okay";
......
...@@ -20,7 +20,7 @@ Optional properties: ...@@ -20,7 +20,7 @@ Optional properties:
Example: Example:
mmc3: mmc@01c12000 { mmc3: mmc@1c12000 {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <0>; #size-cells = <0>;
......
...@@ -13,13 +13,13 @@ Are child nodes of qfprom, bindings of which as described in ...@@ -13,13 +13,13 @@ Are child nodes of qfprom, bindings of which as described in
bindings/nvmem/nvmem.txt bindings/nvmem/nvmem.txt
Example for sun4i: Example for sun4i:
sid@01c23800 { sid@1c23800 {
compatible = "allwinner,sun4i-a10-sid"; compatible = "allwinner,sun4i-a10-sid";
reg = <0x01c23800 0x10> reg = <0x01c23800 0x10>
}; };
Example for sun7i: Example for sun7i:
sid@01c23800 { sid@1c23800 {
compatible = "allwinner,sun7i-a20-sid"; compatible = "allwinner,sun7i-a20-sid";
reg = <0x01c23800 0x200> reg = <0x01c23800 0x200>
}; };
...@@ -10,7 +10,7 @@ Required Properties: ...@@ -10,7 +10,7 @@ Required Properties:
Example: Example:
otp: otp@0301c800 { otp: otp@301c800 {
compatible = "brcm,ocotp"; compatible = "brcm,ocotp";
reg = <0x0301c800 0x2c>; reg = <0x0301c800 0x2c>;
brcm,ocotp-size = <2048>; brcm,ocotp-size = <2048>;
......
...@@ -19,7 +19,7 @@ Optional properties: ...@@ -19,7 +19,7 @@ Optional properties:
Example: Example:
ocotp: ocotp@021bc000 { ocotp: ocotp@21bc000 {
compatible = "fsl,imx6q-ocotp", "syscon"; compatible = "fsl,imx6q-ocotp", "syscon";
reg = <0x021bc000 0x4000>; reg = <0x021bc000 0x4000>;
clocks = <&clks IMX6QDL_CLK_IIM>; clocks = <&clks IMX6QDL_CLK_IIM>;
......
...@@ -33,7 +33,7 @@ bits: Is pair of bit location and number of bits, which specifies offset ...@@ -33,7 +33,7 @@ bits: Is pair of bit location and number of bits, which specifies offset
For example: For example:
/* Provider */ /* Provider */
qfprom: qfprom@00700000 { qfprom: qfprom@700000 {
... ...
/* Data cells */ /* Data cells */
......
...@@ -12,7 +12,7 @@ bindings/nvmem/nvmem.txt ...@@ -12,7 +12,7 @@ bindings/nvmem/nvmem.txt
Example: Example:
qfprom: qfprom@00700000 { qfprom: qfprom@700000 {
compatible = "qcom,qfprom"; compatible = "qcom,qfprom";
reg = <0x00700000 0x8000>; reg = <0x00700000 0x8000>;
... ...
......
...@@ -255,7 +255,7 @@ Tegra30: ...@@ -255,7 +255,7 @@ Tegra30:
SoC DTSI: SoC DTSI:
pcie-controller@00003000 { pcie-controller@3000 {
compatible = "nvidia,tegra30-pcie"; compatible = "nvidia,tegra30-pcie";
device_type = "pci"; device_type = "pci";
reg = <0x00003000 0x00000800 /* PADS registers */ reg = <0x00003000 0x00000800 /* PADS registers */
...@@ -334,7 +334,7 @@ SoC DTSI: ...@@ -334,7 +334,7 @@ SoC DTSI:
Board DTS: Board DTS:
pcie-controller@00003000 { pcie-controller@3000 {
status = "okay"; status = "okay";
avdd-pexa-supply = <&ldo1_reg>; avdd-pexa-supply = <&ldo1_reg>;
...@@ -360,7 +360,7 @@ Tegra124: ...@@ -360,7 +360,7 @@ Tegra124:
SoC DTSI: SoC DTSI:
pcie-controller@01003000 { pcie-controller@1003000 {
compatible = "nvidia,tegra124-pcie"; compatible = "nvidia,tegra124-pcie";
device_type = "pci"; device_type = "pci";
reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */
...@@ -425,7 +425,7 @@ SoC DTSI: ...@@ -425,7 +425,7 @@ SoC DTSI:
Board DTS: Board DTS:
pcie-controller@01003000 { pcie-controller@1003000 {
status = "okay"; status = "okay";
avddio-pex-supply = <&vdd_1v05_run>; avddio-pex-supply = <&vdd_1v05_run>;
...@@ -456,7 +456,7 @@ Tegra210: ...@@ -456,7 +456,7 @@ Tegra210:
SoC DTSI: SoC DTSI:
pcie-controller@01003000 { pcie-controller@1003000 {
compatible = "nvidia,tegra210-pcie"; compatible = "nvidia,tegra210-pcie";
device_type = "pci"; device_type = "pci";
reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */
...@@ -521,7 +521,7 @@ SoC DTSI: ...@@ -521,7 +521,7 @@ SoC DTSI:
Board DTS: Board DTS:
pcie-controller@01003000 { pcie-controller@1003000 {
status = "okay"; status = "okay";
avdd-pll-uerefe-supply = <&avdd_1v05_pll>; avdd-pll-uerefe-supply = <&avdd_1v05_pll>;
......
...@@ -15,7 +15,7 @@ Required properties For the child node: ...@@ -15,7 +15,7 @@ Required properties For the child node:
- #phy-cells: must be 0 - #phy-cells: must be 0
Example: Example:
pcie_phy: phy@0301d0a0 { pcie_phy: phy@301d0a0 {
compatible = "brcm,cygnus-pcie-phy"; compatible = "brcm,cygnus-pcie-phy";
reg = <0x0301d0a0 0x14>; reg = <0x0301d0a0 0x14>;
......
...@@ -23,7 +23,7 @@ Optional properties: ...@@ -23,7 +23,7 @@ Optional properties:
the 17.78mA TX reference current. Default: 100 the 17.78mA TX reference current. Default: 100
Example: Example:
usbphy1: usbphy@020c9000 { usbphy1: usbphy@20c9000 {
compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
reg = <0x020c9000 0x1000>; reg = <0x020c9000 0x1000>;
interrupts = <0 44 0x04>; interrupts = <0 44 0x04>;
......
...@@ -25,7 +25,7 @@ It is recommended to list all clocks and resets available. ...@@ -25,7 +25,7 @@ It is recommended to list all clocks and resets available.
The driver will only use those matching the phy_type. The driver will only use those matching the phy_type.
Example: Example:
usbphy1: phy@00a01800 { usbphy1: phy@a01800 {
compatible = "allwinner,sun9i-a80-usb-phy"; compatible = "allwinner,sun9i-a80-usb-phy";
reg = <0x00a01800 0x4>; reg = <0x00a01800 0x4>;
clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>, clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>,
......
...@@ -89,7 +89,7 @@ Optional subnode-properties: ...@@ -89,7 +89,7 @@ Optional subnode-properties:
Examples: Examples:
pio: pinctrl@01c20800 { pio: pinctrl@1c20800 {
compatible = "allwinner,sun5i-a13-pinctrl"; compatible = "allwinner,sun5i-a13-pinctrl";
reg = <0x01c20800 0x400>; reg = <0x01c20800 0x400>;
#address-cells = <1>; #address-cells = <1>;
......
...@@ -58,14 +58,14 @@ Some requirements for using fsl,imx-pinctrl binding: ...@@ -58,14 +58,14 @@ Some requirements for using fsl,imx-pinctrl binding:
configurations by referring to the phandle of that pin configuration node. configurations by referring to the phandle of that pin configuration node.
Examples: Examples:
usdhc@0219c000 { /* uSDHC4 */ usdhc@219c000 { /* uSDHC4 */
non-removable; non-removable;
vmmc-supply = <&reg_3p3v>; vmmc-supply = <&reg_3p3v>;
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc4_1>; pinctrl-0 = <&pinctrl_usdhc4_1>;
}; };
iomuxc@020e0000 { iomuxc@20e0000 {
compatible = "fsl,imx6q-iomuxc"; compatible = "fsl,imx6q-iomuxc";
reg = <0x020e0000 0x4000>; reg = <0x020e0000 0x4000>;
......
...@@ -89,7 +89,7 @@ Valid values for pin and group names are: ...@@ -89,7 +89,7 @@ Valid values for pin and group names are:
Example: Example:
pinctrl_pdc: pinctrl@02006500 { pinctrl_pdc: pinctrl@2006500 {
#gpio-range-cells = <3>; #gpio-range-cells = <3>;
compatible = "img,tz1090-pdc-pinctrl"; compatible = "img,tz1090-pdc-pinctrl";
reg = <0x02006500 0x100>; reg = <0x02006500 0x100>;
...@@ -121,7 +121,7 @@ Example board file extracts: ...@@ -121,7 +121,7 @@ Example board file extracts:
}; };
}; };
ir: ir@02006200 { ir: ir@2006200 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&irmod_default>; pinctrl-0 = <&irmod_default>;
}; };
...@@ -197,7 +197,7 @@ Valid values for pin and group names are: ...@@ -197,7 +197,7 @@ Valid values for pin and group names are:
Example: Example:
pinctrl: pinctrl@02005800 { pinctrl: pinctrl@2005800 {
#gpio-range-cells = <3>; #gpio-range-cells = <3>;
compatible = "img,tz1090-pinctrl"; compatible = "img,tz1090-pinctrl";
reg = <0x02005800 0xe4>; reg = <0x02005800 0xe4>;
...@@ -221,7 +221,7 @@ Example board file extract: ...@@ -221,7 +221,7 @@ Example board file extract:
}; };
}; };
uart@02004b00 { uart@2004b00 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&uart0_default>; pinctrl-0 = <&uart0_default>;
}; };
...@@ -97,7 +97,7 @@ SoC file extract: ...@@ -97,7 +97,7 @@ SoC file extract:
Board file extract: Board file extract:
------------------- -------------------
pcie-controller@01003000 { pcie-controller@1003000 {
... ...
phys = <&padctl 0>; phys = <&padctl 0>;
......
...@@ -86,7 +86,7 @@ Examples: ...@@ -86,7 +86,7 @@ Examples:
reg = <0 0x1020C020 0 0x1000>; reg = <0 0x1020C020 0 0x1000>;
}; };
pinctrl@01c20800 { pinctrl@1c20800 {
compatible = "mediatek,mt8135-pinctrl"; compatible = "mediatek,mt8135-pinctrl";
reg = <0 0x1000B000 0 0x1000>; reg = <0 0x1000B000 0 0x1000>;
mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>; mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
......
...@@ -89,7 +89,7 @@ Example: ...@@ -89,7 +89,7 @@ Example:
interrupt-names = "irqmux"; interrupt-names = "irqmux";
ranges = <0 0x09610000 0x6000>; ranges = <0 0x09610000 0x6000>;
pio0: gpio@09610000 { pio0: gpio@9610000 {
gpio-controller; gpio-controller;
#gpio-cells = <2>; #gpio-cells = <2>;
interrupt-controller; interrupt-controller;
......
...@@ -175,7 +175,7 @@ to specify in a pin configuration subnode: ...@@ -175,7 +175,7 @@ to specify in a pin configuration subnode:
Example: Example:
tlmm: pinctrl@01010000 { tlmm: pinctrl@1010000 {
compatible = "qcom,msm8996-pinctrl"; compatible = "qcom,msm8996-pinctrl";
reg = <0x01010000 0x300000>; reg = <0x01010000 0x300000>;
interrupts = <0 208 0>; interrupts = <0 208 0>;
......
...@@ -40,7 +40,7 @@ Optional properties: ...@@ -40,7 +40,7 @@ Optional properties:
Example: Example:
gpc: gpc@020dc000 { gpc: gpc@20dc000 {
compatible = "fsl,imx6q-gpc"; compatible = "fsl,imx6q-gpc";
reg = <0x020dc000 0x4000>; reg = <0x020dc000 0x4000>;
interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
...@@ -80,7 +80,7 @@ that is a phandle pointing to the power domain the device belongs to. ...@@ -80,7 +80,7 @@ that is a phandle pointing to the power domain the device belongs to.
Example of a device that is part of the PU power domain: Example of a device that is part of the PU power domain:
vpu: vpu@02040000 { vpu: vpu@2040000 {
reg = <0x02040000 0x3c000>; reg = <0x02040000 0x3c000>;
/* ... */ /* ... */
power-domains = <&pd_pu>; power-domains = <&pd_pu>;
......
...@@ -10,7 +10,7 @@ Required Properties: ...@@ -10,7 +10,7 @@ Required Properties:
-reg: Specifies the physical address of the SNVS_LPCR register -reg: Specifies the physical address of the SNVS_LPCR register
Example: Example:
snvs@020cc000 { snvs@20cc000 {
compatible = "fsl,sec-v4.0-mon", "simple-bus"; compatible = "fsl,sec-v4.0-mon", "simple-bus";
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
......
...@@ -37,12 +37,12 @@ Example 1: ...@@ -37,12 +37,12 @@ Example 1:
Setup keystone reset so that in case software reset or Setup keystone reset so that in case software reset or
WDT0 is triggered it issues hard reset for SoC. WDT0 is triggered it issues hard reset for SoC.
pllctrl: pll-controller@02310000 { pllctrl: pll-controller@2310000 {
compatible = "ti,keystone-pllctrl", "syscon"; compatible = "ti,keystone-pllctrl", "syscon";
reg = <0x02310000 0x200>; reg = <0x02310000 0x200>;
}; };
devctrl: device-state-control@02620000 { devctrl: device-state-control@2620000 {
compatible = "ti,keystone-devctrl", "syscon"; compatible = "ti,keystone-devctrl", "syscon";
reg = <0x02620000 0x1000>; reg = <0x02620000 0x1000>;
}; };
......
...@@ -8,7 +8,7 @@ Required properties: ...@@ -8,7 +8,7 @@ Required properties:
Example: Example:
mcu@0a { mcu@a {
#gpio-cells = <2>; #gpio-cells = <2>;
compatible = "fsl,mc9s08qg8-mpc8349emitx", compatible = "fsl,mc9s08qg8-mpc8349emitx",
"fsl,mcu-mpc8349emitx"; "fsl,mcu-mpc8349emitx";
......
...@@ -14,7 +14,7 @@ Required properties: ...@@ -14,7 +14,7 @@ Required properties:
Example: Example:
pwm: pwm@01c20e00 { pwm: pwm@1c20e00 {
compatible = "allwinner,sun7i-a20-pwm"; compatible = "allwinner,sun7i-a20-pwm";
reg = <0x01c20e00 0xc>; reg = <0x01c20e00 0xc>;
clocks = <&osc24M>; clocks = <&osc24M>;
......
...@@ -40,7 +40,7 @@ to get matched with their hardware counterparts as follow: ...@@ -40,7 +40,7 @@ to get matched with their hardware counterparts as follow:
Example: Example:
max77686: pmic@09 { max77686: pmic@9 {
compatible = "maxim,max77686"; compatible = "maxim,max77686";
interrupt-parent = <&wakeup_eint>; interrupt-parent = <&wakeup_eint>;
interrupts = <26 IRQ_TYPE_NONE>; interrupts = <26 IRQ_TYPE_NONE>;
......
...@@ -71,7 +71,7 @@ has not been disabled for that state using "regulator-off-in-suspend". ...@@ -71,7 +71,7 @@ has not been disabled for that state using "regulator-off-in-suspend".
Example: Example:
max77802@09 { max77802@9 {
compatible = "maxim,max77802"; compatible = "maxim,max77802";
interrupt-parent = <&wakeup_eint>; interrupt-parent = <&wakeup_eint>;
interrupts = <26 0>; interrupts = <26 0>;
......
...@@ -14,7 +14,7 @@ Required properties: ...@@ -14,7 +14,7 @@ Required properties:
example: example:
ahb1_rst: reset@01c202c0 { ahb1_rst: reset@1c202c0 {
#reset-cells = <1>; #reset-cells = <1>;
compatible = "allwinner,sun6i-a31-ahb1-reset"; compatible = "allwinner,sun6i-a31-ahb1-reset";
reg = <0x01c202c0 0xc>; reg = <0x01c202c0 0xc>;
......
...@@ -14,7 +14,7 @@ Required properties: ...@@ -14,7 +14,7 @@ Required properties:
example: example:
src: src@020d8000 { src: src@20d8000 {
compatible = "fsl,imx6q-src"; compatible = "fsl,imx6q-src";
reg = <0x020d8000 0x4000>; reg = <0x020d8000 0x4000>;
interrupts = <0 91 0x04 0 96 0x04>; interrupts = <0 91 0x04 0 96 0x04>;
...@@ -33,10 +33,10 @@ reset.txt ...@@ -33,10 +33,10 @@ reset.txt
example: example:
ipu1: ipu@02400000 { ipu1: ipu@2400000 {
resets = <&src 2>; resets = <&src 2>;
}; };
ipu2: ipu@02800000 { ipu2: ipu@2800000 {
resets = <&src 4>; resets = <&src 4>;
}; };
......
...@@ -67,7 +67,7 @@ using the syscon node, and a consumer (a DSP device) on the TI Keystone 2 ...@@ -67,7 +67,7 @@ using the syscon node, and a consumer (a DSP device) on the TI Keystone 2
/ { / {
soc { soc {
psc: power-sleep-controller@02350000 { psc: power-sleep-controller@2350000 {
compatible = "syscon", "simple-mfd"; compatible = "syscon", "simple-mfd";
reg = <0x02350000 0x1000>; reg = <0x02350000 0x1000>;
......
...@@ -17,7 +17,7 @@ Required properties for new device trees ...@@ -17,7 +17,7 @@ Required properties for new device trees
Example: Example:
rtc: rtc@01f00000 { rtc: rtc@1f00000 {
compatible = "allwinner,sun6i-a31-rtc"; compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>; reg = <0x01f00000 0x54>;
interrupts = <0 40 4>, <0 41 4>; interrupts = <0 40 4>, <0 41 4>;
......
...@@ -10,7 +10,7 @@ Required properties: ...@@ -10,7 +10,7 @@ Required properties:
Example: Example:
rtc: rtc@01c20d00 { rtc: rtc@1c20d00 {
compatible = "allwinner,sun4i-a10-rtc"; compatible = "allwinner,sun4i-a10-rtc";
reg = <0x01c20d00 0x20>; reg = <0x01c20d00 0x20>;
interrupts = <24>; interrupts = <24>;
......
...@@ -18,7 +18,7 @@ par_io@1400 { ...@@ -18,7 +18,7 @@ par_io@1400 {
#size-cells = <0>; #size-cells = <0>;
device_type = "par_io"; device_type = "par_io";
num-ports = <7>; num-ports = <7>;
ucc_pin@01 { ucc_pin@1 {
...... ......
}; };
......
...@@ -26,7 +26,7 @@ Required properties: ...@@ -26,7 +26,7 @@ Required properties:
interrupts. interrupts.
Example: Example:
ucc_pin@01 { ucc_pin@1 {
pio-map = < pio-map = <
/* port pin dir open_drain assignment has_irq */ /* port pin dir open_drain assignment has_irq */
0 3 1 0 1 0 /* TxD0 */ 0 3 1 0 1 0 /* TxD0 */
......
...@@ -51,7 +51,7 @@ of valid identifiers for k2g. ...@@ -51,7 +51,7 @@ of valid identifiers for k2g.
Example (K2G): Example (K2G):
-------------------- --------------------
uart0: serial@02530c00 { uart0: serial@2530c00 {
compatible = "ns16550a"; compatible = "ns16550a";
... ...
power-domains = <&k2g_pds 0x002c>; power-domains = <&k2g_pds 0x002c>;
......
...@@ -9,7 +9,7 @@ Required properties: ...@@ -9,7 +9,7 @@ Required properties:
Examples: Examples:
i2s0: xtfpga-i2s@0d080000 { i2s0: xtfpga-i2s@d080000 {
#sound-dai-cells = <0>; #sound-dai-cells = <0>;
compatible = "cdns,xtfpga-i2s"; compatible = "cdns,xtfpga-i2s";
reg = <0x0d080000 0x40>; reg = <0x0d080000 0x40>;
......
...@@ -41,7 +41,7 @@ Required properties: ...@@ -41,7 +41,7 @@ Required properties:
Example: Example:
asrc: asrc@02034000 { asrc: asrc@2034000 {
compatible = "fsl,imx53-asrc"; compatible = "fsl,imx53-asrc";
reg = <0x02034000 0x4000>; reg = <0x02034000 0x4000>;
interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
......
...@@ -48,7 +48,7 @@ Required properties: ...@@ -48,7 +48,7 @@ Required properties:
Example: Example:
esai: esai@02024000 { esai: esai@2024000 {
compatible = "fsl,imx35-esai"; compatible = "fsl,imx35-esai";
reg = <0x02024000 0x4000>; reg = <0x02024000 0x4000>;
interrupts = <0 51 0x04>; interrupts = <0 51 0x04>;
......
...@@ -39,7 +39,7 @@ Required properties: ...@@ -39,7 +39,7 @@ Required properties:
Example: Example:
spdif: spdif@02004000 { spdif: spdif@2004000 {
compatible = "fsl,imx35-spdif"; compatible = "fsl,imx35-spdif";
reg = <0x02004000 0x4000>; reg = <0x02004000 0x4000>;
interrupts = <0 52 0x04>; interrupts = <0 52 0x04>;
......
...@@ -22,7 +22,7 @@ Required properties of optional child nodes: ...@@ -22,7 +22,7 @@ Required properties of optional child nodes:
Example: Example:
audmux@021d8000 { audmux@21d8000 {
compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux"; compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
reg = <0x021d8000 0x4000>; reg = <0x021d8000 0x4000>;
}; };
...@@ -63,7 +63,7 @@ Optional SoC Specific Properties: ...@@ -63,7 +63,7 @@ Optional SoC Specific Properties:
Example: Example:
i2s0: i2s@03830000 { i2s0: i2s@3830000 {
compatible = "samsung,s5pv210-i2s"; compatible = "samsung,s5pv210-i2s";
reg = <0x03830000 0x100>; reg = <0x03830000 0x100>;
dmas = <&pdma0 10 dmas = <&pdma0 10
......
...@@ -62,7 +62,7 @@ Required properties for the following compatibles: ...@@ -62,7 +62,7 @@ Required properties for the following compatibles:
block in the PRCM. block in the PRCM.
Example: Example:
codec: codec@01c22c00 { codec: codec@1c22c00 {
#sound-dai-cells = <0>; #sound-dai-cells = <0>;
compatible = "allwinner,sun7i-a20-codec"; compatible = "allwinner,sun7i-a20-codec";
reg = <0x01c22c00 0x40>; reg = <0x01c22c00 0x40>;
...@@ -73,7 +73,7 @@ codec: codec@01c22c00 { ...@@ -73,7 +73,7 @@ codec: codec@01c22c00 {
dma-names = "rx", "tx"; dma-names = "rx", "tx";
}; };
codec: codec@01c22c00 { codec: codec@1c22c00 {
#sound-dai-cells = <0>; #sound-dai-cells = <0>;
compatible = "allwinner,sun6i-a31-codec"; compatible = "allwinner,sun6i-a31-codec";
reg = <0x01c22c00 0x98>; reg = <0x01c22c00 0x98>;
......
...@@ -28,7 +28,7 @@ Required properties for the following compatibles: ...@@ -28,7 +28,7 @@ Required properties for the following compatibles:
Example: Example:
i2s0: i2s@01c22400 { i2s0: i2s@1c22400 {
#sound-dai-cells = <0>; #sound-dai-cells = <0>;
compatible = "allwinner,sun4i-a10-i2s"; compatible = "allwinner,sun4i-a10-i2s";
reg = <0x01c22400 0x400>; reg = <0x01c22400 0x400>;
......
...@@ -48,7 +48,7 @@ are similar to A33 using simple-card: ...@@ -48,7 +48,7 @@ are similar to A33 using simple-card:
sound-dai = <&codec>; sound-dai = <&codec>;
}; };
soc@01c00000 { soc@1c00000 {
[...] [...]
audio-codec@1c22e00 { audio-codec@1c22e00 {
......
...@@ -10,7 +10,7 @@ Required properties if not a sub-node of the PRCM node: ...@@ -10,7 +10,7 @@ Required properties if not a sub-node of the PRCM node:
- reg: must contain the registers location and length - reg: must contain the registers location and length
Example: Example:
prcm: prcm@01f01400 { prcm: prcm@1f01400 {
codec_analog: codec-analog { codec_analog: codec-analog {
compatible = "allwinner,sun8i-a23-codec-analog"; compatible = "allwinner,sun8i-a23-codec-analog";
}; };
......
...@@ -31,7 +31,7 @@ Required properties: ...@@ -31,7 +31,7 @@ Required properties:
Example: Example:
spdif: spdif@01c21000 { spdif: spdif@1c21000 {
compatible = "allwinner,sun4i-a10-spdif"; compatible = "allwinner,sun4i-a10-spdif";
reg = <0x01c21000 0x40>; reg = <0x01c21000 0x40>;
interrupts = <13>; interrupts = <13>;
......
...@@ -16,7 +16,7 @@ please check: ...@@ -16,7 +16,7 @@ please check:
* dma/dma.txt * dma/dma.txt
Example: Example:
spdif0: spdif0@0b004000 { spdif0: spdif0@b004000 {
compatible = "zte,zx296702-spdif"; compatible = "zte,zx296702-spdif";
reg = <0x0b004000 0x1000>; reg = <0x0b004000 0x1000>;
clocks = <&lsp0clk ZX296702_SPDIF0_DIV>; clocks = <&lsp0clk ZX296702_SPDIF0_DIV>;
......
...@@ -12,7 +12,7 @@ Required properties: ...@@ -12,7 +12,7 @@ Required properties:
Example: Example:
spi1: spi@01c06000 { spi1: spi@1c06000 {
compatible = "allwinner,sun4i-a10-spi"; compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>; reg = <0x01c06000 0x1000>;
interrupts = <11>; interrupts = <11>;
......
...@@ -19,7 +19,7 @@ Optional properties: ...@@ -19,7 +19,7 @@ Optional properties:
Example: Example:
spi1: spi@01c69000 { spi1: spi@1c69000 {
compatible = "allwinner,sun6i-a31-spi"; compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c69000 0x1000>; reg = <0x01c69000 0x1000>;
interrupts = <0 66 4>; interrupts = <0 66 4>;
...@@ -28,7 +28,7 @@ spi1: spi@01c69000 { ...@@ -28,7 +28,7 @@ spi1: spi@01c69000 {
resets = <&ahb1_rst 21>; resets = <&ahb1_rst 21>;
}; };
spi0: spi@01c68000 { spi0: spi@1c68000 {
compatible = "allwinner,sun8i-h3-spi"; compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>; reg = <0x01c68000 0x1000>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
......
...@@ -19,7 +19,7 @@ found in Documentation/devicetree/bindings/sram/sram.txt ...@@ -19,7 +19,7 @@ found in Documentation/devicetree/bindings/sram/sram.txt
Example: Example:
sysram@02020000 { sysram@2020000 {
compatible = "mmio-sram"; compatible = "mmio-sram";
reg = <0x02020000 0x54000>; reg = <0x02020000 0x54000>;
#address-cells = <1>; #address-cells = <1>;
......
...@@ -47,7 +47,7 @@ This valid values for this argument are: ...@@ -47,7 +47,7 @@ This valid values for this argument are:
Example Example
------- -------
sram-controller@01c00000 { sram-controller@1c00000 {
compatible = "allwinner,sun4i-a10-sram-controller"; compatible = "allwinner,sun4i-a10-sram-controller";
reg = <0x01c00000 0x30>; reg = <0x01c00000 0x30>;
#address-cells = <1>; #address-cells = <1>;
...@@ -68,7 +68,7 @@ sram-controller@01c00000 { ...@@ -68,7 +68,7 @@ sram-controller@01c00000 {
}; };
}; };
emac: ethernet@01c0b000 { emac: ethernet@1c0b000 {
compatible = "allwinner,sun4i-a10-emac"; compatible = "allwinner,sun4i-a10-emac";
... ...
......
...@@ -14,7 +14,7 @@ Optional properties: ...@@ -14,7 +14,7 @@ Optional properties:
Example: Example:
timer@01c60000 { timer@1c60000 {
compatible = "allwinner,sun7i-a20-hstimer"; compatible = "allwinner,sun7i-a20-hstimer";
reg = <0x01c60000 0x1000>; reg = <0x01c60000 0x1000>;
interrupts = <0 51 1>, interrupts = <0 51 1>,
......
...@@ -16,7 +16,7 @@ Required properties: ...@@ -16,7 +16,7 @@ Required properties:
Example: Example:
usb_otg: usb@01c13000 { usb_otg: usb@1c13000 {
compatible = "allwinner,sun4i-a10-musb"; compatible = "allwinner,sun4i-a10-musb";
reg = <0x01c13000 0x0400>; reg = <0x01c13000 0x0400>;
clocks = <&ahb_gates 0>; clocks = <&ahb_gates 0>;
......
...@@ -181,7 +181,7 @@ usb: usb@47400000 { ...@@ -181,7 +181,7 @@ usb: usb@47400000 {
"tx14", "tx15"; "tx14", "tx15";
}; };
cppi41dma: dma-controller@07402000 { cppi41dma: dma-controller@7402000 {
compatible = "ti,am3359-cppi41"; compatible = "ti,am3359-cppi41";
reg = <0x47400000 0x1000 reg = <0x47400000 0x1000
0x47402000 0x1000 0x47402000 0x1000
......
...@@ -18,7 +18,7 @@ Required properties: ...@@ -18,7 +18,7 @@ Required properties:
- atmel,oc-gpio: If present, specifies a gpio that needs to be - atmel,oc-gpio: If present, specifies a gpio that needs to be
activated for the overcurrent detection. activated for the overcurrent detection.
usb0: ohci@00500000 { usb0: ohci@500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci"; compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x100000>; reg = <0x00500000 0x100000>;
clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
...@@ -39,7 +39,7 @@ Required properties: ...@@ -39,7 +39,7 @@ Required properties:
"ehci_clk" for the peripheral clock "ehci_clk" for the peripheral clock
"usb_clk" for the UTMI clock "usb_clk" for the UTMI clock
usb1: ehci@00800000 { usb1: ehci@800000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00800000 0x100000>; reg = <0x00800000 0x100000>;
interrupts = <22 4>; interrupts = <22 4>;
......
...@@ -13,7 +13,7 @@ Optional properties: ...@@ -13,7 +13,7 @@ Optional properties:
Example: Example:
ohci: usb@0225000 { ohci: usb@225000 {
compatible = "ti,da830-ohci"; compatible = "ti,da830-ohci";
reg = <0x225000 0x1000>; reg = <0x225000 0x1000>;
interrupts = <59>; interrupts = <59>;
......
...@@ -30,7 +30,7 @@ Example (Sequoia 440EPx): ...@@ -30,7 +30,7 @@ Example (Sequoia 440EPx):
}; };
Example (Allwinner sun4i A10 SoC): Example (Allwinner sun4i A10 SoC):
ehci0: usb@01c14000 { ehci0: usb@1c14000 {
compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
reg = <0x01c14000 0x100>; reg = <0x01c14000 0x100>;
interrupts = <39>; interrupts = <39>;
......
...@@ -19,7 +19,7 @@ Optional properties: ...@@ -19,7 +19,7 @@ Optional properties:
Example: Example:
ohci0: usb@01c14400 { ohci0: usb@1c14400 {
compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
reg = <0x01c14400 0x100>; reg = <0x01c14400 0x100>;
interrupts = <64>; interrupts = <64>;
......
...@@ -26,7 +26,7 @@ Optional properties: ...@@ -26,7 +26,7 @@ Optional properties:
clock frequencies table is used) clock frequencies table is used)
Examples: Examples:
usb3503@08 { usb3503@8 {
compatible = "smsc,usb3503"; compatible = "smsc,usb3503";
reg = <0x08>; reg = <0x08>;
connect-gpios = <&gpx3 0 1>; connect-gpios = <&gpx3 0 1>;
......
...@@ -10,7 +10,7 @@ Required properties: ...@@ -10,7 +10,7 @@ Required properties:
- reg: Should contain registers location and length - reg: Should contain registers location and length
Examples: Examples:
usbmisc@02184800 { usbmisc@2184800 {
#index-cells = <1>; #index-cells = <1>;
compatible = "fsl,imx6q-usbmisc"; compatible = "fsl,imx6q-usbmisc";
reg = <0x02184800 0x200>; reg = <0x02184800 0x200>;
......
...@@ -13,7 +13,7 @@ Required properties: ...@@ -13,7 +13,7 @@ Required properties:
Example: Example:
wdt: watchdog@010000000 { wdt: watchdog@10000000 {
compatible = "mediatek,mt6589-wdt"; compatible = "mediatek,mt6589-wdt";
reg = <0x10000000 0x18>; reg = <0x10000000 0x18>;
}; };
...@@ -8,7 +8,7 @@ Required properties: ...@@ -8,7 +8,7 @@ Required properties:
Example: Example:
wdt: watchdog@01c20c90 { wdt: watchdog@1c20c90 {
compatible = "allwinner,sun4i-a10-wdt"; compatible = "allwinner,sun4i-a10-wdt";
reg = <0x01c20c90 0x10>; reg = <0x01c20c90 0x10>;
}; };
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment