Merge branch for-rmk-devel of git://aeryn.fluff.org.uk/bjdooks/linux into devel

Documentation/arm/Samsung-S3C24XX/GPIO.txt

@@ -51,7 +51,7 @@ PIN Numbers
 -----------
 
   Each pin has an unique number associated with it in regs-gpio.h,
-  eg S3C2410_GPA0 or S3C2410_GPF1. These defines are used to tell
+  eg S3C2410_GPA(0) or S3C2410_GPF(1). These defines are used to tell
   the GPIO functions which pin is to be used.
 
 
@@ -65,11 +65,11 @@ Configuring a pin
 
   Eg:
 
-     s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0);
-     s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
+     s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0);
+     s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
 
-   which would turn GPA0 into the lowest Address line A0, and set
-   GPE8 to be connected to the SDIO/MMC controller's SDDAT1 line.
+   which would turn GPA(0) into the lowest Address line A0, and set
+   GPE(8) to be connected to the SDIO/MMC controller's SDDAT1 line.
 
 
 Reading the current configuration

arch/arm/common/Kconfig

@@ -4,6 +4,13 @@ config ARM_GIC
 config ARM_VIC
 	bool
 
+config ARM_VIC_NR
+	int
+	default 2
+	help
+	  The maximum number of VICs available in the system, for
+	  power management.
+
 config ICST525
 	bool
 

arch/arm/common/vic.c

@@ -21,6 +21,7 @@
 #include <linux/init.h>
 #include <linux/list.h>
 #include <linux/io.h>
+#include <linux/sysdev.h>
 
 #include <asm/mach/irq.h>
 #include <asm/hardware/vic.h>
@@ -39,11 +40,219 @@ static void vic_unmask_irq(unsigned int irq)
 	writel(1 << irq, base + VIC_INT_ENABLE);
 }
 
+/**
+ * vic_init2 - common initialisation code
+ * @base: Base of the VIC.
+ *
+ * Common initialisation code for registeration
+ * and resume.
+*/
+static void vic_init2(void __iomem *base)
+{
+	int i;
+
+	for (i = 0; i < 16; i++) {
+		void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
+		writel(VIC_VECT_CNTL_ENABLE | i, reg);
+	}
+
+	writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+}
+
+#if defined(CONFIG_PM)
+/**
+ * struct vic_device - VIC PM device
+ * @sysdev: The system device which is registered.
+ * @irq: The IRQ number for the base of the VIC.
+ * @base: The register base for the VIC.
+ * @resume_sources: A bitmask of interrupts for resume.
+ * @resume_irqs: The IRQs enabled for resume.
+ * @int_select: Save for VIC_INT_SELECT.
+ * @int_enable: Save for VIC_INT_ENABLE.
+ * @soft_int: Save for VIC_INT_SOFT.
+ * @protect: Save for VIC_PROTECT.
+ */
+struct vic_device {
+	struct sys_device sysdev;
+
+	void __iomem	*base;
+	int		irq;
+	u32		resume_sources;
+	u32		resume_irqs;
+	u32		int_select;
+	u32		int_enable;
+	u32		soft_int;
+	u32		protect;
+};
+
+/* we cannot allocate memory when VICs are initially registered */
+static struct vic_device vic_devices[CONFIG_ARM_VIC_NR];
+
+static inline struct vic_device *to_vic(struct sys_device *sys)
+{
+	return container_of(sys, struct vic_device, sysdev);
+}
+
+static int vic_id;
+
+static int vic_class_resume(struct sys_device *dev)
+{
+	struct vic_device *vic = to_vic(dev);
+	void __iomem *base = vic->base;
+
+	printk(KERN_DEBUG "%s: resuming vic at %p\n", __func__, base);
+
+	/* re-initialise static settings */
+	vic_init2(base);
+
+	writel(vic->int_select, base + VIC_INT_SELECT);
+	writel(vic->protect, base + VIC_PROTECT);
+
+	/* set the enabled ints and then clear the non-enabled */
+	writel(vic->int_enable, base + VIC_INT_ENABLE);
+	writel(~vic->int_enable, base + VIC_INT_ENABLE_CLEAR);
+
+	/* and the same for the soft-int register */
+
+	writel(vic->soft_int, base + VIC_INT_SOFT);
+	writel(~vic->soft_int, base + VIC_INT_SOFT_CLEAR);
+
+	return 0;
+}
+
+static int vic_class_suspend(struct sys_device *dev, pm_message_t state)
+{
+	struct vic_device *vic = to_vic(dev);
+	void __iomem *base = vic->base;
+
+	printk(KERN_DEBUG "%s: suspending vic at %p\n", __func__, base);
+
+	vic->int_select = readl(base + VIC_INT_SELECT);
+	vic->int_enable = readl(base + VIC_INT_ENABLE);
+	vic->soft_int = readl(base + VIC_INT_SOFT);
+	vic->protect = readl(base + VIC_PROTECT);
+
+	/* set the interrupts (if any) that are used for
+	 * resuming the system */
+
+	writel(vic->resume_irqs, base + VIC_INT_ENABLE);
+	writel(~vic->resume_irqs, base + VIC_INT_ENABLE_CLEAR);
+
+	return 0;
+}
+
+struct sysdev_class vic_class = {
+	.name		= "vic",
+	.suspend	= vic_class_suspend,
+	.resume		= vic_class_resume,
+};
+
+/**
+ * vic_pm_register - Register a VIC for later power management control
+ * @base: The base address of the VIC.
+ * @irq: The base IRQ for the VIC.
+ * @resume_sources: bitmask of interrupts allowed for resume sources.
+ *
+ * Register the VIC with the system device tree so that it can be notified
+ * of suspend and resume requests and ensure that the correct actions are
+ * taken to re-instate the settings on resume.
+ */
+static void __init vic_pm_register(void __iomem *base, unsigned int irq, u32 resume_sources)
+{
+	struct vic_device *v;
+
+	if (vic_id >= ARRAY_SIZE(vic_devices))
+		printk(KERN_ERR "%s: too few VICs, increase CONFIG_ARM_VIC_NR\n", __func__);
+	else {
+		v = &vic_devices[vic_id];
+		v->base = base;
+		v->resume_sources = resume_sources;
+		v->irq = irq;
+		vic_id++;
+	}
+}
+
+/**
+ * vic_pm_init - initicall to register VIC pm
+ *
+ * This is called via late_initcall() to register
+ * the resources for the VICs due to the early
+ * nature of the VIC's registration.
+*/
+static int __init vic_pm_init(void)
+{
+	struct vic_device *dev = vic_devices;
+	int err;
+	int id;
+
+	if (vic_id == 0)
+		return 0;
+
+	err = sysdev_class_register(&vic_class);
+	if (err) {
+		printk(KERN_ERR "%s: cannot register class\n", __func__);
+		return err;
+	}
+
+	for (id = 0; id < vic_id; id++, dev++) {
+		dev->sysdev.id = id;
+		dev->sysdev.cls = &vic_class;
+
+		err = sysdev_register(&dev->sysdev);
+		if (err) {
+			printk(KERN_ERR "%s: failed to register device\n",
+			       __func__);
+			return err;
+		}
+	}
+
+	return 0;
+}
+
+late_initcall(vic_pm_init);
+
+static struct vic_device *vic_from_irq(unsigned int irq)
+{
+        struct vic_device *v = vic_devices;
+	unsigned int base_irq = irq & ~31;
+	int id;
+
+	for (id = 0; id < vic_id; id++, v++) {
+		if (v->irq == base_irq)
+			return v;
+	}
+
+	return NULL;
+}
+
+static int vic_set_wake(unsigned int irq, unsigned int on)
+{
+	struct vic_device *v = vic_from_irq(irq);
+	unsigned int off = irq & 31;
+
+	if (!v)
+		return -EINVAL;
+
+	if (on)
+		v->resume_irqs |= 1 << off;
+	else
+		v->resume_irqs &= ~(1 << off);
+
+	return 0;
+}
+
+#else
+static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg1) { }
+
+#define vic_set_wake NULL
+#endif /* CONFIG_PM */
+
 static struct irq_chip vic_chip = {
 	.name	= "VIC",
 	.ack	= vic_mask_irq,
 	.mask	= vic_mask_irq,
 	.unmask	= vic_unmask_irq,
+	.set_wake = vic_set_wake,
 };
 
 /**
@@ -51,9 +260,10 @@ static struct irq_chip vic_chip = {
  * @base: iomem base address
  * @irq_start: starting interrupt number, must be muliple of 32
  * @vic_sources: bitmask of interrupt sources to allow
+ * @resume_sources: bitmask of interrupt sources to allow for resume
  */
 void __init vic_init(void __iomem *base, unsigned int irq_start,
-		     u32 vic_sources)
+		     u32 vic_sources, u32 resume_sources)
 {
 	unsigned int i;
 
@@ -77,12 +287,7 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 		writel(value, base + VIC_PL190_VECT_ADDR);
 	}
 
-	for (i = 0; i < 16; i++) {
-		void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
-		writel(VIC_VECT_CNTL_ENABLE | i, reg);
-	}
-
-	writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+	vic_init2(base);
 
 	for (i = 0; i < 32; i++) {
 		if (vic_sources & (1 << i)) {
@@ -94,4 +299,6 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
 		}
 	}
+
+	vic_pm_register(base, irq_start, resume_sources);
 }

arch/arm/include/asm/hardware/pl080.h

+/* arch/arm/include/asm/hardware/pl080.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *      http://armlinux.simtec.co.uk/
+ *      Ben Dooks <ben@simtec.co.uk>
+ *
+ * ARM PrimeCell PL080 DMA controller
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* Note, there are some Samsung updates to this controller block which
+ * make it not entierly compatible with the PL080 specification from
+ * ARM. When in doubt, check the Samsung documentation first.
+ *
+ * The Samsung defines are PL080S, and add an extra controll register,
+ * the ability to move more than 2^11 counts of data and some extra
+ * OneNAND features.
+*/
+
+#define PL080_INT_STATUS			(0x00)
+#define PL080_TC_STATUS				(0x04)
+#define PL080_TC_CLEAR				(0x08)
+#define PL080_ERR_STATUS			(0x0C)
+#define PL080_ERR_CLEAR				(0x10)
+#define PL080_RAW_TC_STATUS			(0x14)
+#define PL080_RAW_ERR_STATUS			(0x18)
+#define PL080_EN_CHAN				(0x1c)
+#define PL080_SOFT_BREQ				(0x20)
+#define PL080_SOFT_SREQ				(0x24)
+#define PL080_SOFT_LBREQ			(0x28)
+#define PL080_SOFT_LSREQ			(0x2C)
+
+#define PL080_CONFIG				(0x30)
+#define PL080_CONFIG_M2_BE			(1 << 2)
+#define PL080_CONFIG_M1_BE			(1 << 1)
+#define PL080_CONFIG_ENABLE			(1 << 0)
+
+#define PL080_SYNC				(0x34)
+
+/* Per channel configuration registers */
+
+#define PL008_Cx_STRIDE				(0x20)
+#define PL080_Cx_BASE(x)			((0x100 + (x * 0x20)))
+#define PL080_Cx_SRC_ADDR(x)			((0x100 + (x * 0x20)))
+#define PL080_Cx_DST_ADDR(x)			((0x104 + (x * 0x20)))
+#define PL080_Cx_LLI(x)				((0x108 + (x * 0x20)))
+#define PL080_Cx_CONTROL(x)			((0x10C + (x * 0x20)))
+#define PL080_Cx_CONFIG(x)			((0x110 + (x * 0x20)))
+#define PL080S_Cx_CONTROL2(x)			((0x110 + (x * 0x20)))
+#define PL080S_Cx_CONFIG(x)			((0x114 + (x * 0x20)))
+
+#define PL080_CH_SRC_ADDR			(0x00)
+#define PL080_CH_DST_ADDR			(0x04)
+#define PL080_CH_LLI				(0x08)
+#define PL080_CH_CONTROL			(0x0C)
+#define PL080_CH_CONFIG				(0x10)
+#define PL080S_CH_CONTROL2			(0x10)
+#define PL080S_CH_CONFIG			(0x14)
+
+#define PL080_LLI_ADDR_MASK			(0x3fffffff << 2)
+#define PL080_LLI_ADDR_SHIFT			(2)
+#define PL080_LLI_LM_AHB2			(1 << 0)
+
+#define PL080_CONTROL_TC_IRQ_EN			(1 << 31)
+#define PL080_CONTROL_PROT_MASK			(0x7 << 28)
+#define PL080_CONTROL_PROT_SHIFT		(28)
+#define PL080_CONTROL_PROT_SYS			(1 << 28)
+#define PL080_CONTROL_DST_INCR			(1 << 27)
+#define PL080_CONTROL_SRC_INCR			(1 << 26)
+#define PL080_CONTROL_DST_AHB2			(1 << 25)
+#define PL080_CONTROL_SRC_AHB2			(1 << 24)
+#define PL080_CONTROL_DWIDTH_MASK		(0x7 << 21)
+#define PL080_CONTROL_DWIDTH_SHIFT		(21)
+#define PL080_CONTROL_SWIDTH_MASK		(0x7 << 18)
+#define PL080_CONTROL_SWIDTH_SHIFT		(18)
+#define PL080_CONTROL_DB_SIZE_MASK		(0x7 << 15)
+#define PL080_CONTROL_DB_SIZE_SHIFT		(15)
+#define PL080_CONTROL_SB_SIZE_MASK		(0x7 << 12)
+#define PL080_CONTROL_SB_SIZE_SHIFT		(12)
+#define PL080_CONTROL_TRANSFER_SIZE_MASK	(0xfff << 0)
+#define PL080_CONTROL_TRANSFER_SIZE_SHIFT	(0)
+
+#define PL080_BSIZE_1				(0x0)
+#define PL080_BSIZE_4				(0x1)
+#define PL080_BSIZE_8				(0x2)
+#define PL080_BSIZE_16				(0x3)
+#define PL080_BSIZE_32				(0x4)
+#define PL080_BSIZE_64				(0x5)
+#define PL080_BSIZE_128				(0x6)
+#define PL080_BSIZE_256				(0x7)
+
+#define PL080_WIDTH_8BIT			(0x0)
+#define PL080_WIDTH_16BIT			(0x1)
+#define PL080_WIDTH_32BIT			(0x2)
+
+#define PL080_CONFIG_HALT			(1 << 18)
+#define PL080_CONFIG_ACTIVE			(1 << 17)  /* RO */
+#define PL080_CONFIG_LOCK			(1 << 16)
+#define PL080_CONFIG_TC_IRQ_MASK		(1 << 15)
+#define PL080_CONFIG_ERR_IRQ_MASK		(1 << 14)
+#define PL080_CONFIG_FLOW_CONTROL_MASK		(0x7 << 11)
+#define PL080_CONFIG_FLOW_CONTROL_SHIFT		(11)
+#define PL080_CONFIG_DST_SEL_MASK		(0xf << 6)
+#define PL080_CONFIG_DST_SEL_SHIFT		(6)
+#define PL080_CONFIG_SRC_SEL_MASK		(0xf << 1)
+#define PL080_CONFIG_SRC_SEL_SHIFT		(1)
+#define PL080_CONFIG_ENABLE			(1 << 0)
+
+#define PL080_FLOW_MEM2MEM			(0x0)
+#define PL080_FLOW_MEM2PER			(0x1)
+#define PL080_FLOW_PER2MEM			(0x2)
+#define PL080_FLOW_SRC2DST			(0x3)
+#define PL080_FLOW_SRC2DST_DST			(0x4)
+#define PL080_FLOW_MEM2PER_PER			(0x5)
+#define PL080_FLOW_PER2MEM_PER			(0x6)
+#define PL080_FLOW_SRC2DST_SRC			(0x7)
+
+/* DMA linked list chain structure */
+
+struct pl080_lli {
+	u32	src_addr;
+	u32	dst_addr;
+	u32	next_lli;
+	u32	control0;
+};
+
+struct pl080s_lli {
+	u32	src_addr;
+	u32	dst_addr;
+	u32	next_lli;
+	u32	control0;
+	u32	control1;
+};
+

arch/arm/include/asm/hardware/vic.h

@@ -41,7 +41,7 @@
 #define VIC_PL192_VECT_ADDR		0xF00
 
 #ifndef __ASSEMBLY__
-void vic_init(void __iomem *base, unsigned int irq_start, u32 vic_sources);
+void vic_init(void __iomem *base, unsigned int irq_start, u32 vic_sources, u32 resume_sources);
 #endif
 
 #endif

arch/arm/mach-ep93xx/core.c

@@ -362,8 +362,8 @@ void __init ep93xx_init_irq(void)
 {
 	int gpio_irq;
 
-	vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK);
-	vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK);
+	vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
+	vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
 
 	for (gpio_irq = gpio_to_irq(0);
 	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {

arch/arm/mach-netx/generic.c

@@ -168,7 +168,7 @@ void __init netx_init_irq(void)
 {
 	int irq;
 
-	vic_init(__io(io_p2v(NETX_PA_VIC)), 0, ~0);
+	vic_init(__io(io_p2v(NETX_PA_VIC)), 0, ~0, 0);
 
 	for (irq = NETX_IRQ_HIF_CHAINED(0); irq <= NETX_IRQ_HIF_LAST; irq++) {
 		set_irq_chip(irq, &netx_hif_chip);

arch/arm/mach-s3c2400/gpio.c

@@ -33,10 +33,10 @@
 
 int s3c2400_gpio_getirq(unsigned int pin)
 {
-	if (pin < S3C2410_GPE0 || pin > S3C2400_GPE7_EINT7)
-		return -1;  /* not valid interrupts */
+	if (pin < S3C2410_GPE(0) || pin > S3C2400_GPE(7))
+		return -EINVAL;  /* not valid interrupts */
 
-	return (pin - S3C2410_GPE0) + IRQ_EINT0;
+	return (pin - S3C2410_GPE(0)) + IRQ_EINT0;
 }
 
 EXPORT_SYMBOL(s3c2400_gpio_getirq);

arch/arm/mach-s3c2410/Kconfig

@@ -59,6 +59,7 @@ config ARCH_H1940
 	bool "IPAQ H1940"
 	select CPU_S3C2410
 	select PM_H1940 if PM
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the HP IPAQ H1940
 
@@ -70,6 +71,7 @@ config PM_H1940
 config MACH_N30
 	bool "Acer N30 family"
 	select CPU_S3C2410
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you want suppt for the Acer N30, Acer N35,
 	  Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs.
@@ -82,6 +84,7 @@ config ARCH_BAST
 	select MACH_BAST_IDE
 	select S3C24XX_DCLK
 	select ISA
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Simtec Electronics EB2410ITX
 	  development board (also known as BAST)
@@ -89,6 +92,7 @@ config ARCH_BAST
 config MACH_OTOM
  	bool "NexVision OTOM Board"
  	select CPU_S3C2410
+	select S3C_DEV_USB_HOST
 	help
  	  Say Y here if you are using the Nex Vision OTOM board
 
@@ -96,6 +100,7 @@ config MACH_AML_M5900
 	bool "AML M5900 Series"
 	select CPU_S3C2410
 	select PM_SIMTEC if PM
+	select S3C_DEV_USB_HOST
 	help
 	   Say Y here if you are using the American Microsystems M5900 Series
            <http://www.amltd.com>
@@ -111,6 +116,7 @@ config BAST_PC104_IRQ
 config MACH_TCT_HAMMER
 	bool "TCT Hammer Board"
 	select CPU_S3C2410
+	select S3C_DEV_USB_HOST
 	help
 	   Say Y here if you are using the TinCanTools Hammer Board
            <http://www.tincantools.com>
@@ -122,12 +128,14 @@ config MACH_VR1000
 	select SIMTEC_NOR
 	select MACH_BAST_IDE
 	select CPU_S3C2410
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Thorcom VR1000 board.
 
 config MACH_QT2410
 	bool "QT2410"
 	select CPU_S3C2410
+	select S3C_DEV_USB_HOST
 	help
 	   Say Y here if you are using the Armzone QT2410
 

arch/arm/mach-s3c2410/dma.c

@@ -17,14 +17,16 @@
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 
+#include <mach/map.h>
 #include <mach/dma.h>
 
 #include <plat/cpu.h>
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
 
 #include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
 #include <mach/regs-mem.h>
 #include <mach/regs-lcd.h>
 #include <mach/regs-sdi.h>

arch/arm/mach-s3c2410/gpio.c

@@ -39,12 +39,12 @@ int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
 	unsigned long flags;
 	unsigned long val;
 
-	if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15)
-		return -1;
+	if (pin < S3C2410_GPG(8) || pin > S3C2410_GPG(15))
+		return -EINVAL;
 
 	config &= 0xff;
 
-	pin -= S3C2410_GPG8;
+	pin -= S3C2410_GPG(8);
 	reg += pin & ~3;
 
 	local_irq_save(flags);

arch/arm/mach-s3c2410/h1940-bluetooth.c

@@ -16,6 +16,8 @@
 #include <linux/string.h>
 #include <linux/ctype.h>
 #include <linux/leds.h>
+#include <linux/gpio.h>
+
 #include <mach/regs-gpio.h>
 #include <mach/hardware.h>
 #include <mach/h1940-latch.h>
@@ -41,9 +43,9 @@ static void h1940bt_enable(int on)
 		h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
 		/* Reset the chip */
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH1, 1);
+		s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH1, 0);
+		s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
 
 		state = 1;
 	}
@@ -52,9 +54,9 @@ static void h1940bt_enable(int on)
 		led_trigger_event(bt_led_trigger, 0);
 #endif
 
-		s3c2410_gpio_setpin(S3C2410_GPH1, 1);
+		s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH1, 0);
+		s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
 		mdelay(10);
 		h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
 
@@ -87,14 +89,14 @@ static DEVICE_ATTR(enable, 0644,
 static int __init h1940bt_probe(struct platform_device *pdev)
 {
 	/* Configures BT serial port GPIOs */
-	s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0);
-	s3c2410_gpio_pullup(S3C2410_GPH0, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPH1_OUTP);
-	s3c2410_gpio_pullup(S3C2410_GPH1, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0);
-	s3c2410_gpio_pullup(S3C2410_GPH2, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0);
-	s3c2410_gpio_pullup(S3C2410_GPH3, 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
+	s3c2410_gpio_pullup(S3C2410_GPH(0), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_pullup(S3C2410_GPH(1), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
+	s3c2410_gpio_pullup(S3C2410_GPH(2), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
+	s3c2410_gpio_pullup(S3C2410_GPH(3), 1);
 
 #ifdef CONFIG_LEDS_H1940
 	led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger);

arch/arm/mach-s3c2410/include/mach/dma.h

@@ -3,7 +3,7 @@
  * Copyright (C) 2003,2004,2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
- * Samsung S3C241XX DMA support
+ * Samsung S3C24XX DMA support
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -13,8 +13,8 @@
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H __FILE__
 
+#include <plat/dma.h>
 #include <linux/sysdev.h>
-#include <mach/hardware.h>
 
 #define MAX_DMA_TRANSFER_SIZE   0x100000 /* Data Unit is half word  */
 
@@ -55,9 +55,9 @@ enum dma_ch {
 
 /* we have 4 dma channels */
 #ifndef CONFIG_CPU_S3C2443
-#define S3C2410_DMA_CHANNELS		(4)
+#define S3C_DMA_CHANNELS		(4)
 #else
-#define S3C2410_DMA_CHANNELS		(6)
+#define S3C_DMA_CHANNELS		(6)
 #endif
 
 /* types */
@@ -68,7 +68,6 @@ enum s3c2410_dma_state {
 	S3C2410_DMA_PAUSED
 };
 
-
 /* enum s3c2410_dma_loadst
  *
  * This represents the state of the DMA engine, wrt to the loaded / running
@@ -104,32 +103,6 @@ enum s3c2410_dma_loadst {
 	S3C2410_DMALOAD_1LOADED_1RUNNING,
 };
 
-enum s3c2410_dma_buffresult {
-	S3C2410_RES_OK,
-	S3C2410_RES_ERR,
-	S3C2410_RES_ABORT
-};
-
-enum s3c2410_dmasrc {
-	S3C2410_DMASRC_HW,		/* source is memory */
-	S3C2410_DMASRC_MEM		/* source is hardware */
-};
-
-/* enum s3c2410_chan_op
- *
- * operation codes passed to the DMA code by the user, and also used
- * to inform the current channel owner of any changes to the system state
-*/
-
-enum s3c2410_chan_op {
-	S3C2410_DMAOP_START,
-	S3C2410_DMAOP_STOP,
-	S3C2410_DMAOP_PAUSE,
-	S3C2410_DMAOP_RESUME,
-	S3C2410_DMAOP_FLUSH,
-	S3C2410_DMAOP_TIMEOUT,		/* internal signal to handler */
-	S3C2410_DMAOP_STARTED,		/* indicate channel started */
-};
 
 /* flags */
 
@@ -139,17 +112,14 @@ enum s3c2410_chan_op {
 
 /* dma buffer */
 
-struct s3c2410_dma_client {
-	char                *name;
-};
+struct s3c2410_dma_buf;
 
-/* s3c2410_dma_buf_s
+/* s3c2410_dma_buf
  *
  * internally used buffer structure to describe a queued or running
  * buffer.
 */
 
-struct s3c2410_dma_buf;
 struct s3c2410_dma_buf {
 	struct s3c2410_dma_buf	*next;
 	int			 magic;		/* magic */
@@ -161,20 +131,6 @@ struct s3c2410_dma_buf {
 
 /* [1] is this updated for both recv/send modes? */
 
-struct s3c2410_dma_chan;
-
-/* s3c2410_dma_cbfn_t
- *
- * buffer callback routine type
-*/
-
-typedef void (*s3c2410_dma_cbfn_t)(struct s3c2410_dma_chan *,
-				   void *buf, int size,
-				   enum s3c2410_dma_buffresult result);
-
-typedef int  (*s3c2410_dma_opfn_t)(struct s3c2410_dma_chan *,
-				   enum s3c2410_chan_op );
-
 struct s3c2410_dma_stats {
 	unsigned long		loads;
 	unsigned long		timeout_longest;
@@ -206,10 +162,10 @@ struct s3c2410_dma_chan {
 
 	/* channel configuration */
 	enum s3c2410_dmasrc	 source;
+	enum dma_ch		 req_ch;
 	unsigned long		 dev_addr;
 	unsigned long		 load_timeout;
 	unsigned int		 flags;		/* channel flags */
-	unsigned int		 hw_cfg;	/* last hw config */
 
 	struct s3c24xx_dma_map	*map;		/* channel hw maps */
 
@@ -236,213 +192,6 @@ struct s3c2410_dma_chan {
 	struct sys_device	dev;
 };
 
-/* the currently allocated channel information */
-extern struct s3c2410_dma_chan s3c2410_chans[];
-
-/* note, we don't really use dma_device_t at the moment */
 typedef unsigned long dma_device_t;
 
-/* functions --------------------------------------------------------------- */
-
-/* s3c2410_dma_request
- *
- * request a dma channel exclusivley
-*/
-
-extern int s3c2410_dma_request(unsigned int channel,
-			       struct s3c2410_dma_client *, void *dev);
-
-
-/* s3c2410_dma_ctrl
- *
- * change the state of the dma channel
-*/
-
-extern int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op);
-
-/* s3c2410_dma_setflags
- *
- * set the channel's flags to a given state
-*/
-
-extern int s3c2410_dma_setflags(unsigned int channel,
-				unsigned int flags);
-
-/* s3c2410_dma_free
- *
- * free the dma channel (will also abort any outstanding operations)
-*/
-
-extern int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *);
-
-/* s3c2410_dma_enqueue
- *
- * place the given buffer onto the queue of operations for the channel.
- * The buffer must be allocated from dma coherent memory, or the Dcache/WB
- * drained before the buffer is given to the DMA system.
-*/
-
-extern int s3c2410_dma_enqueue(unsigned int channel, void *id,
-			       dma_addr_t data, int size);
-
-/* s3c2410_dma_config
- *
- * configure the dma channel
-*/
-
-extern int s3c2410_dma_config(unsigned int channel, int xferunit, int dcon);
-
-/* s3c2410_dma_devconfig
- *
- * configure the device we're talking to
-*/
-
-extern int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source,
-				 int hwcfg, unsigned long devaddr);
-
-/* s3c2410_dma_getposition
- *
- * get the position that the dma transfer is currently at
-*/
-
-extern int s3c2410_dma_getposition(unsigned int channel,
-				   dma_addr_t *src, dma_addr_t *dest);
-
-extern int s3c2410_dma_set_opfn(unsigned int, s3c2410_dma_opfn_t rtn);
-extern int s3c2410_dma_set_buffdone_fn(unsigned int, s3c2410_dma_cbfn_t rtn);
-
-/* DMA Register definitions */
-
-#define S3C2410_DMA_DISRC       (0x00)
-#define S3C2410_DMA_DISRCC      (0x04)
-#define S3C2410_DMA_DIDST       (0x08)
-#define S3C2410_DMA_DIDSTC      (0x0C)
-#define S3C2410_DMA_DCON        (0x10)
-#define S3C2410_DMA_DSTAT       (0x14)
-#define S3C2410_DMA_DCSRC       (0x18)
-#define S3C2410_DMA_DCDST       (0x1C)
-#define S3C2410_DMA_DMASKTRIG   (0x20)
-#define S3C2412_DMA_DMAREQSEL	(0x24)
-#define S3C2443_DMA_DMAREQSEL	(0x24)
-
-#define S3C2410_DISRCC_INC	(1<<0)
-#define S3C2410_DISRCC_APB	(1<<1)
-
-#define S3C2410_DMASKTRIG_STOP   (1<<2)
-#define S3C2410_DMASKTRIG_ON     (1<<1)
-#define S3C2410_DMASKTRIG_SWTRIG (1<<0)
-
-#define S3C2410_DCON_DEMAND     (0<<31)
-#define S3C2410_DCON_HANDSHAKE  (1<<31)
-#define S3C2410_DCON_SYNC_PCLK  (0<<30)
-#define S3C2410_DCON_SYNC_HCLK  (1<<30)
-
-#define S3C2410_DCON_INTREQ     (1<<29)
-
-#define S3C2410_DCON_CH0_XDREQ0	(0<<24)
-#define S3C2410_DCON_CH0_UART0	(1<<24)
-#define S3C2410_DCON_CH0_SDI	(2<<24)
-#define S3C2410_DCON_CH0_TIMER	(3<<24)
-#define S3C2410_DCON_CH0_USBEP1	(4<<24)
-
-#define S3C2410_DCON_CH1_XDREQ1	(0<<24)
-#define S3C2410_DCON_CH1_UART1	(1<<24)
-#define S3C2410_DCON_CH1_I2SSDI	(2<<24)
-#define S3C2410_DCON_CH1_SPI	(3<<24)
-#define S3C2410_DCON_CH1_USBEP2	(4<<24)
-
-#define S3C2410_DCON_CH2_I2SSDO	(0<<24)
-#define S3C2410_DCON_CH2_I2SSDI	(1<<24)
-#define S3C2410_DCON_CH2_SDI	(2<<24)
-#define S3C2410_DCON_CH2_TIMER	(3<<24)
-#define S3C2410_DCON_CH2_USBEP3	(4<<24)
-
-#define S3C2410_DCON_CH3_UART2	(0<<24)
-#define S3C2410_DCON_CH3_SDI	(1<<24)
-#define S3C2410_DCON_CH3_SPI	(2<<24)
-#define S3C2410_DCON_CH3_TIMER	(3<<24)
-#define S3C2410_DCON_CH3_USBEP4	(4<<24)
-
-#define S3C2410_DCON_SRCSHIFT   (24)
-#define S3C2410_DCON_SRCMASK	(7<<24)
-
-#define S3C2410_DCON_BYTE       (0<<20)
-#define S3C2410_DCON_HALFWORD   (1<<20)
-#define S3C2410_DCON_WORD       (2<<20)
-
-#define S3C2410_DCON_AUTORELOAD (0<<22)
-#define S3C2410_DCON_NORELOAD   (1<<22)
-#define S3C2410_DCON_HWTRIG     (1<<23)
-
-#ifdef CONFIG_CPU_S3C2440
-#define S3C2440_DIDSTC_CHKINT	(1<<2)
-
-#define S3C2440_DCON_CH0_I2SSDO	(5<<24)
-#define S3C2440_DCON_CH0_PCMIN	(6<<24)
-
-#define S3C2440_DCON_CH1_PCMOUT	(5<<24)
-#define S3C2440_DCON_CH1_SDI	(6<<24)
-
-#define S3C2440_DCON_CH2_PCMIN	(5<<24)
-#define S3C2440_DCON_CH2_MICIN	(6<<24)
-
-#define S3C2440_DCON_CH3_MICIN	(5<<24)
-#define S3C2440_DCON_CH3_PCMOUT	(6<<24)
-#endif
-
-#ifdef CONFIG_CPU_S3C2412
-
-#define S3C2412_DMAREQSEL_SRC(x)	((x)<<1)
-
-#define S3C2412_DMAREQSEL_HW		(1)
-
-#define S3C2412_DMAREQSEL_SPI0TX	S3C2412_DMAREQSEL_SRC(0)
-#define S3C2412_DMAREQSEL_SPI0RX	S3C2412_DMAREQSEL_SRC(1)
-#define S3C2412_DMAREQSEL_SPI1TX	S3C2412_DMAREQSEL_SRC(2)
-#define S3C2412_DMAREQSEL_SPI1RX	S3C2412_DMAREQSEL_SRC(3)
-#define S3C2412_DMAREQSEL_I2STX		S3C2412_DMAREQSEL_SRC(4)
-#define S3C2412_DMAREQSEL_I2SRX		S3C2412_DMAREQSEL_SRC(5)
-#define S3C2412_DMAREQSEL_TIMER		S3C2412_DMAREQSEL_SRC(9)
-#define S3C2412_DMAREQSEL_SDI		S3C2412_DMAREQSEL_SRC(10)
-#define S3C2412_DMAREQSEL_USBEP1	S3C2412_DMAREQSEL_SRC(13)
-#define S3C2412_DMAREQSEL_USBEP2	S3C2412_DMAREQSEL_SRC(14)
-#define S3C2412_DMAREQSEL_USBEP3	S3C2412_DMAREQSEL_SRC(15)
-#define S3C2412_DMAREQSEL_USBEP4	S3C2412_DMAREQSEL_SRC(16)
-#define S3C2412_DMAREQSEL_XDREQ0	S3C2412_DMAREQSEL_SRC(17)
-#define S3C2412_DMAREQSEL_XDREQ1	S3C2412_DMAREQSEL_SRC(18)
-#define S3C2412_DMAREQSEL_UART0_0	S3C2412_DMAREQSEL_SRC(19)
-#define S3C2412_DMAREQSEL_UART0_1	S3C2412_DMAREQSEL_SRC(20)
-#define S3C2412_DMAREQSEL_UART1_0	S3C2412_DMAREQSEL_SRC(21)
-#define S3C2412_DMAREQSEL_UART1_1	S3C2412_DMAREQSEL_SRC(22)
-#define S3C2412_DMAREQSEL_UART2_0	S3C2412_DMAREQSEL_SRC(23)
-#define S3C2412_DMAREQSEL_UART2_1	S3C2412_DMAREQSEL_SRC(24)
-
-#endif
-
-#define S3C2443_DMAREQSEL_SRC(x)	((x)<<1)
-
-#define S3C2443_DMAREQSEL_HW		(1)
-
-#define S3C2443_DMAREQSEL_SPI0TX	S3C2443_DMAREQSEL_SRC(0)
-#define S3C2443_DMAREQSEL_SPI0RX	S3C2443_DMAREQSEL_SRC(1)
-#define S3C2443_DMAREQSEL_SPI1TX	S3C2443_DMAREQSEL_SRC(2)
-#define S3C2443_DMAREQSEL_SPI1RX	S3C2443_DMAREQSEL_SRC(3)
-#define S3C2443_DMAREQSEL_I2STX		S3C2443_DMAREQSEL_SRC(4)
-#define S3C2443_DMAREQSEL_I2SRX		S3C2443_DMAREQSEL_SRC(5)
-#define S3C2443_DMAREQSEL_TIMER		S3C2443_DMAREQSEL_SRC(9)
-#define S3C2443_DMAREQSEL_SDI		S3C2443_DMAREQSEL_SRC(10)
-#define S3C2443_DMAREQSEL_XDREQ0	S3C2443_DMAREQSEL_SRC(17)
-#define S3C2443_DMAREQSEL_XDREQ1	S3C2443_DMAREQSEL_SRC(18)
-#define S3C2443_DMAREQSEL_UART0_0	S3C2443_DMAREQSEL_SRC(19)
-#define S3C2443_DMAREQSEL_UART0_1	S3C2443_DMAREQSEL_SRC(20)
-#define S3C2443_DMAREQSEL_UART1_0	S3C2443_DMAREQSEL_SRC(21)
-#define S3C2443_DMAREQSEL_UART1_1	S3C2443_DMAREQSEL_SRC(22)
-#define S3C2443_DMAREQSEL_UART2_0	S3C2443_DMAREQSEL_SRC(23)
-#define S3C2443_DMAREQSEL_UART2_1	S3C2443_DMAREQSEL_SRC(24)
-#define S3C2443_DMAREQSEL_UART3_0	S3C2443_DMAREQSEL_SRC(25)
-#define S3C2443_DMAREQSEL_UART3_1	S3C2443_DMAREQSEL_SRC(26)
-#define S3C2443_DMAREQSEL_PCMOUT	S3C2443_DMAREQSEL_SRC(27)
-#define S3C2443_DMAREQSEL_PCMIN 	S3C2443_DMAREQSEL_SRC(28)
-#define S3C2443_DMAREQSEL_MICIN		S3C2443_DMAREQSEL_SRC(29)
-
 #endif /* __ASM_ARCH_DMA_H */

arch/arm/mach-s3c2410/include/mach/gpio-core.h

@@ -24,7 +24,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin)
 {
 	struct s3c_gpio_chip *chip;
 
-	if (pin > S3C2410_GPG10)
+	if (pin > S3C2410_GPG(10))
 		return NULL;
 
 	chip = &s3c24xx_gpios[pin/32];

arch/arm/mach-s3c2410/include/mach/gpio-fns.h

+/* arch/arm/mach-s3c2410/include/mach/gpio-fns.h
+ *
+ * Copyright (c) 2003,2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - hardware
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* These functions are in the to-be-removed category and it is strongly
+ * encouraged not to use these in new code. They will be marked deprecated
+ * very soon.
+ *
+ * Most of the functionality can be either replaced by the gpiocfg calls
+ * for the s3c platform or by the generic GPIOlib API.
+*/
+
+/* external functions for GPIO support
+ *
+ * These allow various different clients to access the same GPIO
+ * registers without conflicting. If your driver only owns the entire
+ * GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
+*/
+
+/* s3c2410_gpio_cfgpin
+ *
+ * set the configuration of the given pin to the value passed.
+ *
+ * eg:
+ *    s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0);
+ *    s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
+*/
+
+extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function);
+
+extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
+
+/* s3c2410_gpio_getirq
+ *
+ * turn the given pin number into the corresponding IRQ number
+ *
+ * returns:
+ *	< 0 = no interrupt for this pin
+ *	>=0 = interrupt number for the pin
+*/
+
+extern int s3c2410_gpio_getirq(unsigned int pin);
+
+#ifdef CONFIG_CPU_S3C2400
+
+extern int s3c2400_gpio_getirq(unsigned int pin);
+
+#endif /* CONFIG_CPU_S3C2400 */
+
+/* s3c2410_gpio_irqfilter
+ *
+ * set the irq filtering on the given pin
+ *
+ * on = 0 => disable filtering
+ *      1 => enable filtering
+ *
+ * config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
+ *          width of filter (0 through 63)
+ *
+ *
+*/
+
+extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
+				  unsigned int config);
+
+/* s3c2410_gpio_pullup
+ *
+ * configure the pull-up control on the given pin
+ *
+ * to = 1 => disable the pull-up
+ *      0 => enable the pull-up
+ *
+ * eg;
+ *
+ *   s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
+ *   s3c2410_gpio_pullup(S3C2410_GPE(8), 0);
+*/
+
+extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
+
+/* s3c2410_gpio_getpull
+ *
+ * Read the state of the pull-up on a given pin
+ *
+ * return:
+ *	< 0 => error code
+ *	  0 => enabled
+ *	  1 => disabled
+*/
+
+extern int s3c2410_gpio_getpull(unsigned int pin);
+
+extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
+
+extern unsigned int s3c2410_gpio_getpin(unsigned int pin);

arch/arm/mach-s3c2410/include/mach/gpio-nrs.h

@@ -11,6 +11,9 @@
  * published by the Free Software Foundation.
 */
 
+#ifndef __MACH_GPIONRS_H
+#define __MACH_GPIONRS_H
+
 #define S3C2410_GPIONO(bank,offset) ((bank) + (offset))
 
 #define S3C2410_GPIO_BANKA   (32*0)
@@ -21,3 +24,70 @@
 #define S3C2410_GPIO_BANKF   (32*5)
 #define S3C2410_GPIO_BANKG   (32*6)
 #define S3C2410_GPIO_BANKH   (32*7)
+
+/* GPIO bank sizes */
+#define S3C2410_GPIO_A_NR	(32)
+#define S3C2410_GPIO_B_NR	(32)
+#define S3C2410_GPIO_C_NR	(32)
+#define S3C2410_GPIO_D_NR	(32)
+#define S3C2410_GPIO_E_NR	(32)
+#define S3C2410_GPIO_F_NR	(32)
+#define S3C2410_GPIO_G_NR	(32)
+#define S3C2410_GPIO_H_NR	(32)
+
+#if CONFIG_S3C_GPIO_SPACE != 0
+#error CONFIG_S3C_GPIO_SPACE cannot be zero at the moment
+#endif
+
+#define S3C2410_GPIO_NEXT(__gpio) \
+	((__gpio##_START) + (__gpio##_NR) + CONFIG_S3C_GPIO_SPACE + 0)
+
+#ifndef __ASSEMBLY__
+
+enum s3c_gpio_number {
+	S3C2410_GPIO_A_START = 0,
+	S3C2410_GPIO_B_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_A),
+	S3C2410_GPIO_C_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_B),
+	S3C2410_GPIO_D_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_C),
+	S3C2410_GPIO_E_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_D),
+	S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E),
+	S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F),
+	S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G),
+};
+
+#endif /* __ASSEMBLY__ */
+
+/* S3C2410 GPIO number definitions. */
+
+#define S3C2410_GPA(_nr)	(S3C2410_GPIO_A_START + (_nr))
+#define S3C2410_GPB(_nr)	(S3C2410_GPIO_B_START + (_nr))
+#define S3C2410_GPC(_nr)	(S3C2410_GPIO_C_START + (_nr))
+#define S3C2410_GPD(_nr)	(S3C2410_GPIO_D_START + (_nr))
+#define S3C2410_GPE(_nr)	(S3C2410_GPIO_E_START + (_nr))
+#define S3C2410_GPF(_nr)	(S3C2410_GPIO_F_START + (_nr))
+#define S3C2410_GPG(_nr)	(S3C2410_GPIO_G_START + (_nr))
+#define S3C2410_GPH(_nr)	(S3C2410_GPIO_H_START + (_nr))
+
+/* compatibility until drivers can be modified */
+
+#define S3C2410_GPA0	S3C2410_GPA(0)
+#define S3C2410_GPA1	S3C2410_GPA(1)
+#define S3C2410_GPA3	S3C2410_GPA(3)
+#define S3C2410_GPA7	S3C2410_GPA(7)
+
+#define S3C2410_GPE0	S3C2410_GPE(0)
+#define S3C2410_GPE1	S3C2410_GPE(1)
+#define S3C2410_GPE2	S3C2410_GPE(2)
+#define S3C2410_GPE3	S3C2410_GPE(3)
+#define S3C2410_GPE4	S3C2410_GPE(4)
+#define S3C2410_GPE5	S3C2410_GPE(5)
+#define S3C2410_GPE6	S3C2410_GPE(6)
+#define S3C2410_GPE7	S3C2410_GPE(7)
+#define S3C2410_GPE8	S3C2410_GPE(8)
+#define S3C2410_GPE9	S3C2410_GPE(9)
+#define S3C2410_GPE10	S3C2410_GPE(10)
+
+#define S3C2410_GPH10	S3C2410_GPH(10)
+
+#endif /* __MACH_GPIONRS_H */
+

arch/arm/mach-s3c2410/include/mach/gpio.h

@@ -24,5 +24,6 @@
 
 #include <asm-generic/gpio.h>
 #include <mach/gpio-nrs.h>
+#include <mach/gpio-fns.h>
 
 #define S3C_GPIO_END	(S3C2410_GPIO_BANKH + 32)

arch/arm/mach-s3c2410/include/mach/hardware.h

@@ -15,101 +15,6 @@
 
 #ifndef __ASSEMBLY__
 
-/* external functions for GPIO support
- *
- * These allow various different clients to access the same GPIO
- * registers without conflicting. If your driver only owns the entire
- * GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
-*/
-
-/* s3c2410_gpio_cfgpin
- *
- * set the configuration of the given pin to the value passed.
- *
- * eg:
- *    s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0);
- *    s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
-*/
-
-extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function);
-
-extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
-
-/* s3c2410_gpio_getirq
- *
- * turn the given pin number into the corresponding IRQ number
- *
- * returns:
- *	< 0 = no interrupt for this pin
- *	>=0 = interrupt number for the pin
-*/
-
-extern int s3c2410_gpio_getirq(unsigned int pin);
-
-/* s3c2410_gpio_irq2pin
- *
- * turn the given irq number into the corresponding GPIO number
- *
- * returns:
- *	< 0 = no pin
- *	>=0 = gpio pin number
-*/
-
-extern int s3c2410_gpio_irq2pin(unsigned int irq);
-
-#ifdef CONFIG_CPU_S3C2400
-
-extern int s3c2400_gpio_getirq(unsigned int pin);
-
-#endif /* CONFIG_CPU_S3C2400 */
-
-/* s3c2410_gpio_irqfilter
- *
- * set the irq filtering on the given pin
- *
- * on = 0 => disable filtering
- *      1 => enable filtering
- *
- * config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
- *          width of filter (0 through 63)
- *
- *
-*/
-
-extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
-				  unsigned int config);
-
-/* s3c2410_gpio_pullup
- *
- * configure the pull-up control on the given pin
- *
- * to = 1 => disable the pull-up
- *      0 => enable the pull-up
- *
- * eg;
- *
- *   s3c2410_gpio_pullup(S3C2410_GPB0, 0);
- *   s3c2410_gpio_pullup(S3C2410_GPE8, 0);
-*/
-
-extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
-
-/* s3c2410_gpio_getpull
- *
- * Read the state of the pull-up on a given pin
- *
- * return:
- *	< 0 => error code
- *	  0 => enabled
- *	  1 => disabled
-*/
-
-extern int s3c2410_gpio_getpull(unsigned int pin);
-
-extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
-
-extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
-
 extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg);
 
 #ifdef CONFIG_CPU_S3C2440

arch/arm/mach-s3c2410/include/mach/map.h

@@ -84,7 +84,6 @@
 
 #define S3C24XX_PA_IRQ      S3C2410_PA_IRQ
 #define S3C24XX_PA_MEMCTRL  S3C2410_PA_MEMCTRL
-#define S3C24XX_PA_USBHOST  S3C2410_PA_USBHOST
 #define S3C24XX_PA_DMA      S3C2410_PA_DMA
 #define S3C24XX_PA_CLKPWR   S3C2410_PA_CLKPWR
 #define S3C24XX_PA_LCD      S3C2410_PA_LCD
@@ -102,6 +101,7 @@
 
 #define S3C_PA_IIC          S3C2410_PA_IIC
 #define S3C_PA_UART	    S3C24XX_PA_UART
+#define S3C_PA_USBHOST	S3C2410_PA_USBHOST
 #define S3C_PA_HSMMC0	    S3C2443_PA_HSMMC
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s3c2410/include/mach/regs-gpio.h

@@ -69,104 +69,58 @@
 #define S3C2400_GPACON	   S3C2410_GPIOREG(0x00)
 #define S3C2400_GPADAT	   S3C2410_GPIOREG(0x04)
 
-#define S3C2410_GPA0         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 0)
-#define S3C2410_GPA0_OUT     (0<<0)
 #define S3C2410_GPA0_ADDR0   (1<<0)
 
-#define S3C2410_GPA1         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 1)
-#define S3C2410_GPA1_OUT     (0<<1)
 #define S3C2410_GPA1_ADDR16  (1<<1)
 
-#define S3C2410_GPA2         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 2)
-#define S3C2410_GPA2_OUT     (0<<2)
 #define S3C2410_GPA2_ADDR17  (1<<2)
 
-#define S3C2410_GPA3         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 3)
-#define S3C2410_GPA3_OUT     (0<<3)
 #define S3C2410_GPA3_ADDR18  (1<<3)
 
-#define S3C2410_GPA4         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 4)
-#define S3C2410_GPA4_OUT     (0<<4)
 #define S3C2410_GPA4_ADDR19  (1<<4)
 
-#define S3C2410_GPA5         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 5)
-#define S3C2410_GPA5_OUT     (0<<5)
 #define S3C2410_GPA5_ADDR20  (1<<5)
 
-#define S3C2410_GPA6         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 6)
-#define S3C2410_GPA6_OUT     (0<<6)
 #define S3C2410_GPA6_ADDR21  (1<<6)
 
-#define S3C2410_GPA7         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 7)
-#define S3C2410_GPA7_OUT     (0<<7)
 #define S3C2410_GPA7_ADDR22  (1<<7)
 
-#define S3C2410_GPA8         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 8)
-#define S3C2410_GPA8_OUT     (0<<8)
 #define S3C2410_GPA8_ADDR23  (1<<8)
 
-#define S3C2410_GPA9         S3C2410_GPIONO(S3C2410_GPIO_BANKA, 9)
-#define S3C2410_GPA9_OUT     (0<<9)
 #define S3C2410_GPA9_ADDR24  (1<<9)
 
-#define S3C2410_GPA10        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 10)
-#define S3C2410_GPA10_OUT    (0<<10)
 #define S3C2410_GPA10_ADDR25 (1<<10)
 #define S3C2400_GPA10_SCKE   (1<<10)
 
-#define S3C2410_GPA11        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 11)
-#define S3C2410_GPA11_OUT    (0<<11)
 #define S3C2410_GPA11_ADDR26 (1<<11)
 #define S3C2400_GPA11_nCAS0  (1<<11)
 
-#define S3C2410_GPA12        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 12)
-#define S3C2410_GPA12_OUT    (0<<12)
 #define S3C2410_GPA12_nGCS1  (1<<12)
 #define S3C2400_GPA12_nCAS1  (1<<12)
 
-#define S3C2410_GPA13        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 13)
-#define S3C2410_GPA13_OUT    (0<<13)
 #define S3C2410_GPA13_nGCS2  (1<<13)
 #define S3C2400_GPA13_nGCS1  (1<<13)
 
-#define S3C2410_GPA14        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 14)
-#define S3C2410_GPA14_OUT    (0<<14)
 #define S3C2410_GPA14_nGCS3  (1<<14)
 #define S3C2400_GPA14_nGCS2  (1<<14)
 
-#define S3C2410_GPA15        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 15)
-#define S3C2410_GPA15_OUT    (0<<15)
 #define S3C2410_GPA15_nGCS4  (1<<15)
 #define S3C2400_GPA15_nGCS3  (1<<15)
 
-#define S3C2410_GPA16        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 16)
-#define S3C2410_GPA16_OUT    (0<<16)
 #define S3C2410_GPA16_nGCS5  (1<<16)
 #define S3C2400_GPA16_nGCS4  (1<<16)
 
-#define S3C2410_GPA17        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 17)
-#define S3C2410_GPA17_OUT    (0<<17)
 #define S3C2410_GPA17_CLE    (1<<17)
 #define S3C2400_GPA17_nGCS5  (1<<17)
 
-#define S3C2410_GPA18        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 18)
-#define S3C2410_GPA18_OUT    (0<<18)
 #define S3C2410_GPA18_ALE    (1<<18)
 
-#define S3C2410_GPA19        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 19)
-#define S3C2410_GPA19_OUT    (0<<19)
 #define S3C2410_GPA19_nFWE   (1<<19)
 
-#define S3C2410_GPA20        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 20)
-#define S3C2410_GPA20_OUT    (0<<20)
 #define S3C2410_GPA20_nFRE   (1<<20)
 
-#define S3C2410_GPA21        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 21)
-#define S3C2410_GPA21_OUT    (0<<21)
 #define S3C2410_GPA21_nRSTOUT (1<<21)
 
-#define S3C2410_GPA22        S3C2410_GPIONO(S3C2410_GPIO_BANKA, 22)
-#define S3C2410_GPA22_OUT    (0<<22)
 #define S3C2410_GPA22_nFCE   (1<<22)
 
 /* 0x08 and 0x0c are reserved on S3C2410 */
@@ -194,107 +148,69 @@
 
 /* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */
 
-#define S3C2410_GPB0         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 0)
-#define S3C2410_GPB0_INP     (0x00 << 0)
-#define S3C2410_GPB0_OUTP    (0x01 << 0)
 #define S3C2410_GPB0_TOUT0   (0x02 << 0)
 #define S3C2400_GPB0_DATA16  (0x02 << 0)
 
-#define S3C2410_GPB1         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 1)
-#define S3C2410_GPB1_INP     (0x00 << 2)
-#define S3C2410_GPB1_OUTP    (0x01 << 2)
 #define S3C2410_GPB1_TOUT1   (0x02 << 2)
 #define S3C2400_GPB1_DATA17  (0x02 << 2)
 
-#define S3C2410_GPB2         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 2)
-#define S3C2410_GPB2_INP     (0x00 << 4)
-#define S3C2410_GPB2_OUTP    (0x01 << 4)
 #define S3C2410_GPB2_TOUT2   (0x02 << 4)
 #define S3C2400_GPB2_DATA18  (0x02 << 4)
 #define S3C2400_GPB2_TCLK1   (0x03 << 4)
 
-#define S3C2410_GPB3         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 3)
-#define S3C2410_GPB3_INP     (0x00 << 6)
-#define S3C2410_GPB3_OUTP    (0x01 << 6)
 #define S3C2410_GPB3_TOUT3   (0x02 << 6)
 #define S3C2400_GPB3_DATA19  (0x02 << 6)
 #define S3C2400_GPB3_TXD1    (0x03 << 6)
 
-#define S3C2410_GPB4         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 4)
-#define S3C2410_GPB4_INP     (0x00 << 8)
-#define S3C2410_GPB4_OUTP    (0x01 << 8)
 #define S3C2410_GPB4_TCLK0   (0x02 << 8)
 #define S3C2400_GPB4_DATA20  (0x02 << 8)
 #define S3C2410_GPB4_MASK    (0x03 << 8)
 #define S3C2400_GPB4_RXD1    (0x03 << 8)
 #define S3C2400_GPB4_MASK    (0x03 << 8)
 
-#define S3C2410_GPB5         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 5)
-#define S3C2410_GPB5_INP     (0x00 << 10)
-#define S3C2410_GPB5_OUTP    (0x01 << 10)
 #define S3C2410_GPB5_nXBACK  (0x02 << 10)
 #define S3C2443_GPB5_XBACK   (0x03 << 10)
 #define S3C2400_GPB5_DATA21  (0x02 << 10)
 #define S3C2400_GPB5_nCTS1   (0x03 << 10)
 
-#define S3C2410_GPB6         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 6)
-#define S3C2410_GPB6_INP     (0x00 << 12)
-#define S3C2410_GPB6_OUTP    (0x01 << 12)
 #define S3C2410_GPB6_nXBREQ  (0x02 << 12)
 #define S3C2443_GPB6_XBREQ   (0x03 << 12)
 #define S3C2400_GPB6_DATA22  (0x02 << 12)
 #define S3C2400_GPB6_nRTS1   (0x03 << 12)
 
-#define S3C2410_GPB7         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 7)
-#define S3C2410_GPB7_INP     (0x00 << 14)
-#define S3C2410_GPB7_OUTP    (0x01 << 14)
 #define S3C2410_GPB7_nXDACK1 (0x02 << 14)
 #define S3C2443_GPB7_XDACK1  (0x03 << 14)
 #define S3C2400_GPB7_DATA23  (0x02 << 14)
 
-#define S3C2410_GPB8         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 8)
-#define S3C2410_GPB8_INP     (0x00 << 16)
-#define S3C2410_GPB8_OUTP    (0x01 << 16)
 #define S3C2410_GPB8_nXDREQ1 (0x02 << 16)
 #define S3C2400_GPB8_DATA24  (0x02 << 16)
 
-#define S3C2410_GPB9         S3C2410_GPIONO(S3C2410_GPIO_BANKB, 9)
-#define S3C2410_GPB9_INP     (0x00 << 18)
-#define S3C2410_GPB9_OUTP    (0x01 << 18)
 #define S3C2410_GPB9_nXDACK0 (0x02 << 18)
 #define S3C2443_GPB9_XDACK0  (0x03 << 18)
 #define S3C2400_GPB9_DATA25  (0x02 << 18)
 #define S3C2400_GPB9_I2SSDI  (0x03 << 18)
 
-#define S3C2410_GPB10        S3C2410_GPIONO(S3C2410_GPIO_BANKB, 10)
-#define S3C2410_GPB10_INP    (0x00 << 20)
-#define S3C2410_GPB10_OUTP   (0x01 << 20)
 #define S3C2410_GPB10_nXDRE0 (0x02 << 20)
 #define S3C2443_GPB10_XDREQ0 (0x03 << 20)
 #define S3C2400_GPB10_DATA26 (0x02 << 20)
 #define S3C2400_GPB10_nSS    (0x03 << 20)
 
-#define S3C2400_GPB11        S3C2410_GPIONO(S3C2410_GPIO_BANKB, 11)
 #define S3C2400_GPB11_INP    (0x00 << 22)
 #define S3C2400_GPB11_OUTP   (0x01 << 22)
 #define S3C2400_GPB11_DATA27 (0x02 << 22)
 
-#define S3C2400_GPB12        S3C2410_GPIONO(S3C2410_GPIO_BANKB, 12)
 #define S3C2400_GPB12_INP    (0x00 << 24)
 #define S3C2400_GPB12_OUTP   (0x01 << 24)
 #define S3C2400_GPB12_DATA28 (0x02 << 24)
 
-#define S3C2400_GPB13        S3C2410_GPIONO(S3C2410_GPIO_BANKB, 13)
 #define S3C2400_GPB13_INP    (0x00 << 26)
 #define S3C2400_GPB13_OUTP   (0x01 << 26)
 #define S3C2400_GPB13_DATA29 (0x02 << 26)
 
-#define S3C2400_GPB14        S3C2410_GPIONO(S3C2410_GPIO_BANKB, 14)
 #define S3C2400_GPB14_INP    (0x00 << 28)
 #define S3C2400_GPB14_OUTP   (0x01 << 28)
 #define S3C2400_GPB14_DATA30 (0x02 << 28)
 
-#define S3C2400_GPB15        S3C2410_GPIONO(S3C2410_GPIO_BANKB, 15)
 #define S3C2400_GPB15_INP    (0x00 << 30)
 #define S3C2400_GPB15_OUTP   (0x01 << 30)
 #define S3C2400_GPB15_DATA31 (0x02 << 30)
@@ -315,99 +231,51 @@
 #define S3C2400_GPCDAT	   S3C2410_GPIOREG(0x18)
 #define S3C2400_GPCUP	   S3C2410_GPIOREG(0x1C)
 
-#define S3C2410_GPC0            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 0)
-#define S3C2410_GPC0_INP	(0x00 << 0)
-#define S3C2410_GPC0_OUTP	(0x01 << 0)
 #define S3C2410_GPC0_LEND	(0x02 << 0)
 #define S3C2400_GPC0_VD0 	(0x02 << 0)
 
-#define S3C2410_GPC1            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 1)
-#define S3C2410_GPC1_INP	(0x00 << 2)
-#define S3C2410_GPC1_OUTP	(0x01 << 2)
 #define S3C2410_GPC1_VCLK	(0x02 << 2)
 #define S3C2400_GPC1_VD1 	(0x02 << 2)
 
-#define S3C2410_GPC2            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 2)
-#define S3C2410_GPC2_INP	(0x00 << 4)
-#define S3C2410_GPC2_OUTP	(0x01 << 4)
 #define S3C2410_GPC2_VLINE	(0x02 << 4)
 #define S3C2400_GPC2_VD2  	(0x02 << 4)
 
-#define S3C2410_GPC3            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 3)
-#define S3C2410_GPC3_INP	(0x00 << 6)
-#define S3C2410_GPC3_OUTP	(0x01 << 6)
 #define S3C2410_GPC3_VFRAME	(0x02 << 6)
 #define S3C2400_GPC3_VD3   	(0x02 << 6)
 
-#define S3C2410_GPC4            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 4)
-#define S3C2410_GPC4_INP	(0x00 << 8)
-#define S3C2410_GPC4_OUTP	(0x01 << 8)
 #define S3C2410_GPC4_VM		(0x02 << 8)
 #define S3C2400_GPC4_VD4	(0x02 << 8)
 
-#define S3C2410_GPC5            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 5)
-#define S3C2410_GPC5_INP	(0x00 << 10)
-#define S3C2410_GPC5_OUTP	(0x01 << 10)
 #define S3C2410_GPC5_LCDVF0	(0x02 << 10)
 #define S3C2400_GPC5_VD5   	(0x02 << 10)
 
-#define S3C2410_GPC6            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 6)
-#define S3C2410_GPC6_INP	(0x00 << 12)
-#define S3C2410_GPC6_OUTP	(0x01 << 12)
 #define S3C2410_GPC6_LCDVF1	(0x02 << 12)
 #define S3C2400_GPC6_VD6   	(0x02 << 12)
 
-#define S3C2410_GPC7            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 7)
-#define S3C2410_GPC7_INP	(0x00 << 14)
-#define S3C2410_GPC7_OUTP	(0x01 << 14)
 #define S3C2410_GPC7_LCDVF2	(0x02 << 14)
 #define S3C2400_GPC7_VD7   	(0x02 << 14)
 
-#define S3C2410_GPC8            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 8)
-#define S3C2410_GPC8_INP	(0x00 << 16)
-#define S3C2410_GPC8_OUTP	(0x01 << 16)
 #define S3C2410_GPC8_VD0	(0x02 << 16)
 #define S3C2400_GPC8_VD8	(0x02 << 16)
 
-#define S3C2410_GPC9            S3C2410_GPIONO(S3C2410_GPIO_BANKC, 9)
-#define S3C2410_GPC9_INP	(0x00 << 18)
-#define S3C2410_GPC9_OUTP	(0x01 << 18)
 #define S3C2410_GPC9_VD1	(0x02 << 18)
 #define S3C2400_GPC9_VD9	(0x02 << 18)
 
-#define S3C2410_GPC10           S3C2410_GPIONO(S3C2410_GPIO_BANKC, 10)
-#define S3C2410_GPC10_INP	(0x00 << 20)
-#define S3C2410_GPC10_OUTP	(0x01 << 20)
 #define S3C2410_GPC10_VD2	(0x02 << 20)
 #define S3C2400_GPC10_VD10	(0x02 << 20)
 
-#define S3C2410_GPC11           S3C2410_GPIONO(S3C2410_GPIO_BANKC, 11)
-#define S3C2410_GPC11_INP	(0x00 << 22)
-#define S3C2410_GPC11_OUTP	(0x01 << 22)
 #define S3C2410_GPC11_VD3	(0x02 << 22)
 #define S3C2400_GPC11_VD11	(0x02 << 22)
 
-#define S3C2410_GPC12           S3C2410_GPIONO(S3C2410_GPIO_BANKC, 12)
-#define S3C2410_GPC12_INP	(0x00 << 24)
-#define S3C2410_GPC12_OUTP	(0x01 << 24)
 #define S3C2410_GPC12_VD4	(0x02 << 24)
 #define S3C2400_GPC12_VD12	(0x02 << 24)
 
-#define S3C2410_GPC13           S3C2410_GPIONO(S3C2410_GPIO_BANKC, 13)
-#define S3C2410_GPC13_INP	(0x00 << 26)
-#define S3C2410_GPC13_OUTP	(0x01 << 26)
 #define S3C2410_GPC13_VD5	(0x02 << 26)
 #define S3C2400_GPC13_VD13	(0x02 << 26)
 
-#define S3C2410_GPC14           S3C2410_GPIONO(S3C2410_GPIO_BANKC, 14)
-#define S3C2410_GPC14_INP	(0x00 << 28)
-#define S3C2410_GPC14_OUTP	(0x01 << 28)
 #define S3C2410_GPC14_VD6	(0x02 << 28)
 #define S3C2400_GPC14_VD14	(0x02 << 28)
 
-#define S3C2410_GPC15           S3C2410_GPIONO(S3C2410_GPIO_BANKC, 15)
-#define S3C2410_GPC15_INP	(0x00 << 30)
-#define S3C2410_GPC15_OUTP	(0x01 << 30)
 #define S3C2410_GPC15_VD7	(0x02 << 30)
 #define S3C2400_GPC15_VD15	(0x02 << 30)
 
@@ -432,99 +300,51 @@
 #define S3C2400_GPDDAT	   S3C2410_GPIOREG(0x24)
 #define S3C2400_GPDUP	   S3C2410_GPIOREG(0x28)
 
-#define S3C2410_GPD0            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 0)
-#define S3C2410_GPD0_INP	(0x00 << 0)
-#define S3C2410_GPD0_OUTP	(0x01 << 0)
 #define S3C2410_GPD0_VD8	(0x02 << 0)
 #define S3C2400_GPD0_VFRAME	(0x02 << 0)
 #define S3C2442_GPD0_nSPICS1	(0x03 << 0)
 
-#define S3C2410_GPD1            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1)
-#define S3C2410_GPD1_INP	(0x00 << 2)
-#define S3C2410_GPD1_OUTP	(0x01 << 2)
 #define S3C2410_GPD1_VD9	(0x02 << 2)
 #define S3C2400_GPD1_VM		(0x02 << 2)
 #define S3C2442_GPD1_SPICLK1	(0x03 << 2)
 
-#define S3C2410_GPD2            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2)
-#define S3C2410_GPD2_INP	(0x00 << 4)
-#define S3C2410_GPD2_OUTP	(0x01 << 4)
 #define S3C2410_GPD2_VD10	(0x02 << 4)
 #define S3C2400_GPD2_VLINE	(0x02 << 4)
 
-#define S3C2410_GPD3            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 3)
-#define S3C2410_GPD3_INP	(0x00 << 6)
-#define S3C2410_GPD3_OUTP	(0x01 << 6)
 #define S3C2410_GPD3_VD11	(0x02 << 6)
 #define S3C2400_GPD3_VCLK	(0x02 << 6)
 
-#define S3C2410_GPD4            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 4)
-#define S3C2410_GPD4_INP	(0x00 << 8)
-#define S3C2410_GPD4_OUTP	(0x01 << 8)
 #define S3C2410_GPD4_VD12	(0x02 << 8)
 #define S3C2400_GPD4_LEND	(0x02 << 8)
 
-#define S3C2410_GPD5            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 5)
-#define S3C2410_GPD5_INP	(0x00 << 10)
-#define S3C2410_GPD5_OUTP	(0x01 << 10)
 #define S3C2410_GPD5_VD13	(0x02 << 10)
 #define S3C2400_GPD5_TOUT0	(0x02 << 10)
 
-#define S3C2410_GPD6            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 6)
-#define S3C2410_GPD6_INP	(0x00 << 12)
-#define S3C2410_GPD6_OUTP	(0x01 << 12)
 #define S3C2410_GPD6_VD14	(0x02 << 12)
 #define S3C2400_GPD6_TOUT1	(0x02 << 12)
 
-#define S3C2410_GPD7            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 7)
-#define S3C2410_GPD7_INP	(0x00 << 14)
-#define S3C2410_GPD7_OUTP	(0x01 << 14)
 #define S3C2410_GPD7_VD15	(0x02 << 14)
 #define S3C2400_GPD7_TOUT2	(0x02 << 14)
 
-#define S3C2410_GPD8            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 8)
-#define S3C2410_GPD8_INP	(0x00 << 16)
-#define S3C2410_GPD8_OUTP	(0x01 << 16)
 #define S3C2410_GPD8_VD16	(0x02 << 16)
 #define S3C2400_GPD8_TOUT3	(0x02 << 16)
 
-#define S3C2410_GPD9            S3C2410_GPIONO(S3C2410_GPIO_BANKD, 9)
-#define S3C2410_GPD9_INP	(0x00 << 18)
-#define S3C2410_GPD9_OUTP	(0x01 << 18)
 #define S3C2410_GPD9_VD17	(0x02 << 18)
 #define S3C2400_GPD9_TCLK0	(0x02 << 18)
 #define S3C2410_GPD9_MASK       (0x03 << 18)
 
-#define S3C2410_GPD10           S3C2410_GPIONO(S3C2410_GPIO_BANKD, 10)
-#define S3C2410_GPD10_INP	(0x00 << 20)
-#define S3C2410_GPD10_OUTP	(0x01 << 20)
 #define S3C2410_GPD10_VD18	(0x02 << 20)
 #define S3C2400_GPD10_nWAIT	(0x02 << 20)
 
-#define S3C2410_GPD11           S3C2410_GPIONO(S3C2410_GPIO_BANKD, 11)
-#define S3C2410_GPD11_INP	(0x00 << 22)
-#define S3C2410_GPD11_OUTP	(0x01 << 22)
 #define S3C2410_GPD11_VD19	(0x02 << 22)
 
-#define S3C2410_GPD12           S3C2410_GPIONO(S3C2410_GPIO_BANKD, 12)
-#define S3C2410_GPD12_INP	(0x00 << 24)
-#define S3C2410_GPD12_OUTP	(0x01 << 24)
 #define S3C2410_GPD12_VD20	(0x02 << 24)
 
-#define S3C2410_GPD13           S3C2410_GPIONO(S3C2410_GPIO_BANKD, 13)
-#define S3C2410_GPD13_INP	(0x00 << 26)
-#define S3C2410_GPD13_OUTP	(0x01 << 26)
 #define S3C2410_GPD13_VD21	(0x02 << 26)
 
-#define S3C2410_GPD14           S3C2410_GPIONO(S3C2410_GPIO_BANKD, 14)
-#define S3C2410_GPD14_INP	(0x00 << 28)
-#define S3C2410_GPD14_OUTP	(0x01 << 28)
 #define S3C2410_GPD14_VD22	(0x02 << 28)
 #define S3C2410_GPD14_nSS1	(0x03 << 28)
 
-#define S3C2410_GPD15           S3C2410_GPIONO(S3C2410_GPIO_BANKD, 15)
-#define S3C2410_GPD15_INP	(0x00 << 30)
-#define S3C2410_GPD15_OUTP	(0x01 << 30)
 #define S3C2410_GPD15_VD23	(0x02 << 30)
 #define S3C2410_GPD15_nSS0	(0x03 << 30)
 
@@ -550,34 +370,22 @@
 #define S3C2400_GPEDAT	   S3C2410_GPIOREG(0x30)
 #define S3C2400_GPEUP	   S3C2410_GPIOREG(0x34)
 
-#define S3C2410_GPE0           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 0)
-#define S3C2410_GPE0_INP       (0x00 << 0)
-#define S3C2410_GPE0_OUTP      (0x01 << 0)
 #define S3C2410_GPE0_I2SLRCK   (0x02 << 0)
 #define S3C2443_GPE0_AC_nRESET (0x03 << 0)
 #define S3C2400_GPE0_EINT0     (0x02 << 0)
 #define S3C2410_GPE0_MASK      (0x03 << 0)
 
-#define S3C2410_GPE1           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 1)
-#define S3C2410_GPE1_INP       (0x00 << 2)
-#define S3C2410_GPE1_OUTP      (0x01 << 2)
 #define S3C2410_GPE1_I2SSCLK   (0x02 << 2)
 #define S3C2443_GPE1_AC_SYNC   (0x03 << 2)
 #define S3C2400_GPE1_EINT1     (0x02 << 2)
 #define S3C2400_GPE1_nSS       (0x03 << 2)
 #define S3C2410_GPE1_MASK      (0x03 << 2)
 
-#define S3C2410_GPE2           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 2)
-#define S3C2410_GPE2_INP       (0x00 << 4)
-#define S3C2410_GPE2_OUTP      (0x01 << 4)
 #define S3C2410_GPE2_CDCLK     (0x02 << 4)
 #define S3C2443_GPE2_AC_BITCLK (0x03 << 4)
 #define S3C2400_GPE2_EINT2     (0x02 << 4)
 #define S3C2400_GPE2_I2SSDI    (0x03 << 4)
 
-#define S3C2410_GPE3           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 3)
-#define S3C2410_GPE3_INP       (0x00 << 6)
-#define S3C2410_GPE3_OUTP      (0x01 << 6)
 #define S3C2410_GPE3_I2SSDI    (0x02 << 6)
 #define S3C2443_GPE3_AC_SDI    (0x03 << 6)
 #define S3C2400_GPE3_EINT3     (0x02 << 6)
@@ -585,9 +393,6 @@
 #define S3C2410_GPE3_nSS0      (0x03 << 6)
 #define S3C2410_GPE3_MASK      (0x03 << 6)
 
-#define S3C2410_GPE4           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 4)
-#define S3C2410_GPE4_INP       (0x00 << 8)
-#define S3C2410_GPE4_OUTP      (0x01 << 8)
 #define S3C2410_GPE4_I2SSDO    (0x02 << 8)
 #define S3C2443_GPE4_AC_SDO    (0x03 << 8)
 #define S3C2400_GPE4_EINT4     (0x02 << 8)
@@ -595,81 +400,48 @@
 #define S3C2410_GPE4_I2SSDI    (0x03 << 8)
 #define S3C2410_GPE4_MASK      (0x03 << 8)
 
-#define S3C2410_GPE5           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 5)
-#define S3C2410_GPE5_INP       (0x00 << 10)
-#define S3C2410_GPE5_OUTP      (0x01 << 10)
 #define S3C2410_GPE5_SDCLK     (0x02 << 10)
 #define S3C2443_GPE5_SD1_CLK   (0x02 << 10)
 #define S3C2400_GPE5_EINT5     (0x02 << 10)
 #define S3C2400_GPE5_TCLK1     (0x03 << 10)
 
-#define S3C2410_GPE6           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 6)
-#define S3C2410_GPE6_INP       (0x00 << 12)
-#define S3C2410_GPE6_OUTP      (0x01 << 12)
 #define S3C2410_GPE6_SDCMD     (0x02 << 12)
 #define S3C2443_GPE6_SD1_CMD   (0x02 << 12)
 #define S3C2443_GPE6_AC_BITCLK (0x03 << 12)
 #define S3C2400_GPE6_EINT6     (0x02 << 12)
 
-#define S3C2410_GPE7           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 7)
-#define S3C2410_GPE7_INP       (0x00 << 14)
-#define S3C2410_GPE7_OUTP      (0x01 << 14)
 #define S3C2410_GPE7_SDDAT0    (0x02 << 14)
 #define S3C2443_GPE5_SD1_DAT0  (0x02 << 14)
 #define S3C2443_GPE7_AC_SDI    (0x03 << 14)
 #define S3C2400_GPE7_EINT7     (0x02 << 14)
 
-#define S3C2410_GPE8           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 8)
-#define S3C2410_GPE8_INP       (0x00 << 16)
-#define S3C2410_GPE8_OUTP      (0x01 << 16)
 #define S3C2410_GPE8_SDDAT1    (0x02 << 16)
 #define S3C2443_GPE8_SD1_DAT1  (0x02 << 16)
 #define S3C2443_GPE8_AC_SDO    (0x03 << 16)
 #define S3C2400_GPE8_nXDACK0   (0x02 << 16)
 
-#define S3C2410_GPE9           S3C2410_GPIONO(S3C2410_GPIO_BANKE, 9)
-#define S3C2410_GPE9_INP       (0x00 << 18)
-#define S3C2410_GPE9_OUTP      (0x01 << 18)
 #define S3C2410_GPE9_SDDAT2    (0x02 << 18)
 #define S3C2443_GPE9_SD1_DAT2  (0x02 << 18)
 #define S3C2443_GPE9_AC_SYNC   (0x03 << 18)
 #define S3C2400_GPE9_nXDACK1   (0x02 << 18)
 #define S3C2400_GPE9_nXBACK    (0x03 << 18)
 
-#define S3C2410_GPE10          S3C2410_GPIONO(S3C2410_GPIO_BANKE, 10)
-#define S3C2410_GPE10_INP      (0x00 << 20)
-#define S3C2410_GPE10_OUTP     (0x01 << 20)
 #define S3C2410_GPE10_SDDAT3   (0x02 << 20)
 #define S3C2443_GPE10_SD1_DAT3 (0x02 << 20)
 #define S3C2443_GPE10_AC_nRESET (0x03 << 20)
 #define S3C2400_GPE10_nXDREQ0  (0x02 << 20)
 
-#define S3C2410_GPE11          S3C2410_GPIONO(S3C2410_GPIO_BANKE, 11)
-#define S3C2410_GPE11_INP      (0x00 << 22)
-#define S3C2410_GPE11_OUTP     (0x01 << 22)
 #define S3C2410_GPE11_SPIMISO0 (0x02 << 22)
 #define S3C2400_GPE11_nXDREQ1  (0x02 << 22)
 #define S3C2400_GPE11_nXBREQ   (0x03 << 22)
 
-#define S3C2410_GPE12          S3C2410_GPIONO(S3C2410_GPIO_BANKE, 12)
-#define S3C2410_GPE12_INP      (0x00 << 24)
-#define S3C2410_GPE12_OUTP     (0x01 << 24)
 #define S3C2410_GPE12_SPIMOSI0 (0x02 << 24)
 
-#define S3C2410_GPE13          S3C2410_GPIONO(S3C2410_GPIO_BANKE, 13)
-#define S3C2410_GPE13_INP      (0x00 << 26)
-#define S3C2410_GPE13_OUTP     (0x01 << 26)
 #define S3C2410_GPE13_SPICLK0  (0x02 << 26)
 
-#define S3C2410_GPE14          S3C2410_GPIONO(S3C2410_GPIO_BANKE, 14)
-#define S3C2410_GPE14_INP      (0x00 << 28)
-#define S3C2410_GPE14_OUTP     (0x01 << 28)
 #define S3C2410_GPE14_IICSCL   (0x02 << 28)
 #define S3C2410_GPE14_MASK     (0x03 << 28)
 
-#define S3C2410_GPE15          S3C2410_GPIONO(S3C2410_GPIO_BANKE, 15)
-#define S3C2410_GPE15_INP      (0x00 << 30)
-#define S3C2410_GPE15_OUTP     (0x01 << 30)
 #define S3C2410_GPE15_IICSDA   (0x02 << 30)
 #define S3C2410_GPE15_MASK     (0x03 << 30)
 
@@ -705,55 +477,31 @@
 #define S3C2400_GPFDAT	   S3C2410_GPIOREG(0x3C)
 #define S3C2400_GPFUP	   S3C2410_GPIOREG(0x40)
 
-#define S3C2410_GPF0        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 0)
-#define S3C2410_GPF0_INP    (0x00 << 0)
-#define S3C2410_GPF0_OUTP   (0x01 << 0)
 #define S3C2410_GPF0_EINT0  (0x02 << 0)
 #define S3C2400_GPF0_RXD0   (0x02 << 0)
 
-#define S3C2410_GPF1        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 1)
-#define S3C2410_GPF1_INP    (0x00 << 2)
-#define S3C2410_GPF1_OUTP   (0x01 << 2)
 #define S3C2410_GPF1_EINT1  (0x02 << 2)
 #define S3C2400_GPF1_RXD1   (0x02 << 2)
 #define S3C2400_GPF1_IICSDA (0x03 << 2)
 
-#define S3C2410_GPF2        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 2)
-#define S3C2410_GPF2_INP    (0x00 << 4)
-#define S3C2410_GPF2_OUTP   (0x01 << 4)
 #define S3C2410_GPF2_EINT2  (0x02 << 4)
 #define S3C2400_GPF2_TXD0   (0x02 << 4)
 
-#define S3C2410_GPF3        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 3)
-#define S3C2410_GPF3_INP    (0x00 << 6)
-#define S3C2410_GPF3_OUTP   (0x01 << 6)
 #define S3C2410_GPF3_EINT3  (0x02 << 6)
 #define S3C2400_GPF3_TXD1   (0x02 << 6)
 #define S3C2400_GPF3_IICSCL (0x03 << 6)
 
-#define S3C2410_GPF4        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 4)
-#define S3C2410_GPF4_INP    (0x00 << 8)
-#define S3C2410_GPF4_OUTP   (0x01 << 8)
 #define S3C2410_GPF4_EINT4  (0x02 << 8)
 #define S3C2400_GPF4_nRTS0  (0x02 << 8)
 #define S3C2400_GPF4_nXBACK (0x03 << 8)
 
-#define S3C2410_GPF5        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 5)
-#define S3C2410_GPF5_INP    (0x00 << 10)
-#define S3C2410_GPF5_OUTP   (0x01 << 10)
 #define S3C2410_GPF5_EINT5  (0x02 << 10)
 #define S3C2400_GPF5_nCTS0  (0x02 << 10)
 #define S3C2400_GPF5_nXBREQ (0x03 << 10)
 
-#define S3C2410_GPF6        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 6)
-#define S3C2410_GPF6_INP    (0x00 << 12)
-#define S3C2410_GPF6_OUTP   (0x01 << 12)
 #define S3C2410_GPF6_EINT6  (0x02 << 12)
 #define S3C2400_GPF6_CLKOUT (0x02 << 12)
 
-#define S3C2410_GPF7        S3C2410_GPIONO(S3C2410_GPIO_BANKF, 7)
-#define S3C2410_GPF7_INP    (0x00 << 14)
-#define S3C2410_GPF7_OUTP   (0x01 << 14)
 #define S3C2410_GPF7_EINT7  (0x02 << 14)
 
 #define S3C2410_GPF_PUPDIS(x)  (1<<(x))
@@ -778,117 +526,69 @@
 #define S3C2400_GPGDAT	   S3C2410_GPIOREG(0x48)
 #define S3C2400_GPGUP	   S3C2410_GPIOREG(0x4C)
 
-#define S3C2410_GPG0          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 0)
-#define S3C2410_GPG0_INP      (0x00 << 0)
-#define S3C2410_GPG0_OUTP     (0x01 << 0)
 #define S3C2410_GPG0_EINT8    (0x02 << 0)
 #define S3C2400_GPG0_I2SLRCK  (0x02 << 0)
 
-#define S3C2410_GPG1          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 1)
-#define S3C2410_GPG1_INP      (0x00 << 2)
-#define S3C2410_GPG1_OUTP     (0x01 << 2)
 #define S3C2410_GPG1_EINT9    (0x02 << 2)
 #define S3C2400_GPG1_I2SSCLK  (0x02 << 2)
 
-#define S3C2410_GPG2          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 2)
-#define S3C2410_GPG2_INP      (0x00 << 4)
-#define S3C2410_GPG2_OUTP     (0x01 << 4)
 #define S3C2410_GPG2_EINT10   (0x02 << 4)
 #define S3C2410_GPG2_nSS0     (0x03 << 4)
 #define S3C2400_GPG2_CDCLK    (0x02 << 4)
 
-#define S3C2410_GPG3          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 3)
-#define S3C2410_GPG3_INP      (0x00 << 6)
-#define S3C2410_GPG3_OUTP     (0x01 << 6)
 #define S3C2410_GPG3_EINT11   (0x02 << 6)
 #define S3C2410_GPG3_nSS1     (0x03 << 6)
 #define S3C2400_GPG3_I2SSDO   (0x02 << 6)
 #define S3C2400_GPG3_I2SSDI   (0x03 << 6)
 
-#define S3C2410_GPG4          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 4)
-#define S3C2410_GPG4_INP      (0x00 << 8)
-#define S3C2410_GPG4_OUTP     (0x01 << 8)
 #define S3C2410_GPG4_EINT12   (0x02 << 8)
 #define S3C2400_GPG4_MMCCLK   (0x02 << 8)
 #define S3C2400_GPG4_I2SSDI   (0x03 << 8)
 #define S3C2410_GPG4_LCDPWREN (0x03 << 8)
 #define S3C2443_GPG4_LCDPWRDN (0x03 << 8)
 
-#define S3C2410_GPG5          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 5)
-#define S3C2410_GPG5_INP      (0x00 << 10)
-#define S3C2410_GPG5_OUTP     (0x01 << 10)
 #define S3C2410_GPG5_EINT13   (0x02 << 10)
 #define S3C2400_GPG5_MMCCMD   (0x02 << 10)
 #define S3C2400_GPG5_IICSDA   (0x03 << 10)
 #define S3C2410_GPG5_SPIMISO1 (0x03 << 10)	/* not s3c2443 */
 
-#define S3C2410_GPG6          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 6)
-#define S3C2410_GPG6_INP      (0x00 << 12)
-#define S3C2410_GPG6_OUTP     (0x01 << 12)
 #define S3C2410_GPG6_EINT14   (0x02 << 12)
 #define S3C2400_GPG6_MMCDAT   (0x02 << 12)
 #define S3C2400_GPG6_IICSCL   (0x03 << 12)
 #define S3C2410_GPG6_SPIMOSI1 (0x03 << 12)
 
-#define S3C2410_GPG7          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 7)
-#define S3C2410_GPG7_INP      (0x00 << 14)
-#define S3C2410_GPG7_OUTP     (0x01 << 14)
 #define S3C2410_GPG7_EINT15   (0x02 << 14)
 #define S3C2410_GPG7_SPICLK1  (0x03 << 14)
 #define S3C2400_GPG7_SPIMISO  (0x02 << 14)
 #define S3C2400_GPG7_IICSDA   (0x03 << 14)
 
-#define S3C2410_GPG8          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 8)
-#define S3C2410_GPG8_INP      (0x00 << 16)
-#define S3C2410_GPG8_OUTP     (0x01 << 16)
 #define S3C2410_GPG8_EINT16   (0x02 << 16)
 #define S3C2400_GPG8_SPIMOSI  (0x02 << 16)
 #define S3C2400_GPG8_IICSCL   (0x03 << 16)
 
-#define S3C2410_GPG9          S3C2410_GPIONO(S3C2410_GPIO_BANKG, 9)
-#define S3C2410_GPG9_INP      (0x00 << 18)
-#define S3C2410_GPG9_OUTP     (0x01 << 18)
 #define S3C2410_GPG9_EINT17   (0x02 << 18)
 #define S3C2400_GPG9_SPICLK   (0x02 << 18)
 #define S3C2400_GPG9_MMCCLK   (0x03 << 18)
 
-#define S3C2410_GPG10         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 10)
-#define S3C2410_GPG10_INP     (0x00 << 20)
-#define S3C2410_GPG10_OUTP    (0x01 << 20)
 #define S3C2410_GPG10_EINT18  (0x02 << 20)
 
-#define S3C2410_GPG11         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 11)
-#define S3C2410_GPG11_INP     (0x00 << 22)
-#define S3C2410_GPG11_OUTP    (0x01 << 22)
 #define S3C2410_GPG11_EINT19  (0x02 << 22)
 #define S3C2410_GPG11_TCLK1   (0x03 << 22)
 #define S3C2443_GPG11_CF_nIREQ (0x03 << 22)
 
-#define S3C2410_GPG12         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 12)
-#define S3C2410_GPG12_INP     (0x00 << 24)
-#define S3C2410_GPG12_OUTP    (0x01 << 24)
 #define S3C2410_GPG12_EINT20  (0x02 << 24)
 #define S3C2410_GPG12_XMON    (0x03 << 24)
 #define S3C2442_GPG12_nSPICS0 (0x03 << 24)
 #define S3C2443_GPG12_nINPACK (0x03 << 24)
 
-#define S3C2410_GPG13         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13)
-#define S3C2410_GPG13_INP     (0x00 << 26)
-#define S3C2410_GPG13_OUTP    (0x01 << 26)
 #define S3C2410_GPG13_EINT21  (0x02 << 26)
 #define S3C2410_GPG13_nXPON   (0x03 << 26)
 #define S3C2443_GPG13_CF_nREG (0x03 << 26)
 
-#define S3C2410_GPG14         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 14)
-#define S3C2410_GPG14_INP     (0x00 << 28)
-#define S3C2410_GPG14_OUTP    (0x01 << 28)
 #define S3C2410_GPG14_EINT22  (0x02 << 28)
 #define S3C2410_GPG14_YMON    (0x03 << 28)
 #define S3C2443_GPG14_CF_RESET (0x03 << 28)
 
-#define S3C2410_GPG15         S3C2410_GPIONO(S3C2410_GPIO_BANKG, 15)
-#define S3C2410_GPG15_INP     (0x00 << 30)
-#define S3C2410_GPG15_OUTP    (0x01 << 30)
 #define S3C2410_GPG15_EINT23  (0x02 << 30)
 #define S3C2410_GPG15_nYPON   (0x03 << 30)
 #define S3C2443_GPG15_CF_PWR  (0x03 << 30)
@@ -907,62 +607,29 @@
 #define S3C2410_GPHDAT	   S3C2410_GPIOREG(0x74)
 #define S3C2410_GPHUP	   S3C2410_GPIOREG(0x78)
 
-#define S3C2410_GPH0        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 0)
-#define S3C2410_GPH0_INP    (0x00 << 0)
-#define S3C2410_GPH0_OUTP   (0x01 << 0)
 #define S3C2410_GPH0_nCTS0  (0x02 << 0)
 
-#define S3C2410_GPH1        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 1)
-#define S3C2410_GPH1_INP    (0x00 << 2)
-#define S3C2410_GPH1_OUTP   (0x01 << 2)
 #define S3C2410_GPH1_nRTS0  (0x02 << 2)
 
-#define S3C2410_GPH2        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 2)
-#define S3C2410_GPH2_INP    (0x00 << 4)
-#define S3C2410_GPH2_OUTP   (0x01 << 4)
 #define S3C2410_GPH2_TXD0   (0x02 << 4)
 
-#define S3C2410_GPH3        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 3)
-#define S3C2410_GPH3_INP    (0x00 << 6)
-#define S3C2410_GPH3_OUTP   (0x01 << 6)
 #define S3C2410_GPH3_RXD0   (0x02 << 6)
 
-#define S3C2410_GPH4        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 4)
-#define S3C2410_GPH4_INP    (0x00 << 8)
-#define S3C2410_GPH4_OUTP   (0x01 << 8)
 #define S3C2410_GPH4_TXD1   (0x02 << 8)
 
-#define S3C2410_GPH5        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 5)
-#define S3C2410_GPH5_INP    (0x00 << 10)
-#define S3C2410_GPH5_OUTP   (0x01 << 10)
 #define S3C2410_GPH5_RXD1   (0x02 << 10)
 
-#define S3C2410_GPH6        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 6)
-#define S3C2410_GPH6_INP    (0x00 << 12)
-#define S3C2410_GPH6_OUTP   (0x01 << 12)
 #define S3C2410_GPH6_TXD2   (0x02 << 12)
 #define S3C2410_GPH6_nRTS1  (0x03 << 12)
 
-#define S3C2410_GPH7        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 7)
-#define S3C2410_GPH7_INP    (0x00 << 14)
-#define S3C2410_GPH7_OUTP   (0x01 << 14)
 #define S3C2410_GPH7_RXD2   (0x02 << 14)
 #define S3C2410_GPH7_nCTS1  (0x03 << 14)
 
-#define S3C2410_GPH8        S3C2410_GPIONO(S3C2410_GPIO_BANKH, 8)
-#define S3C2410_GPH8_INP    (0x00 << 16)
-#define S3C2410_GPH8_OUTP   (0x01 << 16)
 #define S3C2410_GPH8_UCLK   (0x02 << 16)
 
-#define S3C2410_GPH9          S3C2410_GPIONO(S3C2410_GPIO_BANKH, 9)
-#define S3C2410_GPH9_INP      (0x00 << 18)
-#define S3C2410_GPH9_OUTP     (0x01 << 18)
 #define S3C2410_GPH9_CLKOUT0  (0x02 << 18)
 #define S3C2442_GPH9_nSPICS0  (0x03 << 18)
 
-#define S3C2410_GPH10         S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10)
-#define S3C2410_GPH10_INP     (0x00 << 20)
-#define S3C2410_GPH10_OUTP    (0x01 << 20)
 #define S3C2410_GPH10_CLKOUT1 (0x02 << 20)
 
 /* The S3C2412 and S3C2413 move the GPJ register set to after

arch/arm/mach-s3c2410/include/mach/system-reset.h

@@ -11,21 +11,13 @@
 */
 
 #include <mach/hardware.h>
-#include <linux/io.h>
-
-#include <plat/regs-watchdog.h>
-#include <mach/regs-clock.h>
-
-#include <linux/clk.h>
-#include <linux/err.h>
+#include <plat/watchdog-reset.h>
 
 extern void (*s3c24xx_reset_hook)(void);
 
 static void
 arch_reset(char mode, const char *cmd)
 {
-	struct clk *wdtclk;
-
 	if (mode == 's') {
 		cpu_reset(0);
 	}
@@ -33,31 +25,7 @@ arch_reset(char mode, const char *cmd)
 	if (s3c24xx_reset_hook)
 		s3c24xx_reset_hook();
 
-	printk("arch_reset: attempting watchdog reset\n");
-
-	__raw_writel(0, S3C2410_WTCON);	  /* disable watchdog, to be safe  */
-
-	wdtclk = clk_get(NULL, "watchdog");
-	if (!IS_ERR(wdtclk)) {
-		clk_enable(wdtclk);
-	} else
-		printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__);
-
-	/* put initial values into count and data */
-	__raw_writel(0x80, S3C2410_WTCNT);
-	__raw_writel(0x80, S3C2410_WTDAT);
-
-	/* set the watchdog to go and reset... */
-	__raw_writel(S3C2410_WTCON_ENABLE|S3C2410_WTCON_DIV16|S3C2410_WTCON_RSTEN |
-		     S3C2410_WTCON_PRESCALE(0x20), S3C2410_WTCON);
-
-	/* wait for reset to assert... */
-	mdelay(500);
-
-	printk(KERN_ERR "Watchdog reset failed to assert reset\n");
-
-	/* delay to allow the serial port to show the message */
-	mdelay(50);
+	arch_wdt_reset();
 
 	/* we'll take a jump through zero as a poor second */
 	cpu_reset(0);

arch/arm/mach-s3c2410/mach-amlm5900.c

@@ -32,6 +32,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/proc_fs.h>
@@ -224,8 +225,8 @@ static void amlm5900_init_pm(void)
 	} else {
 		enable_irq_wake(IRQ_EINT9);
 		/* configure the suspend/resume status pin */
-		s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP);
-		s3c2410_gpio_pullup(S3C2410_GPF2, 0);
+		s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
+		s3c2410_gpio_pullup(S3C2410_GPF(2), 0);
 	}
 }
 static void __init amlm5900_init(void)

arch/arm/mach-s3c2410/mach-bast.c

@@ -16,6 +16,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
@@ -212,15 +213,15 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 static int bast_pm_suspend(struct sys_device *sd, pm_message_t state)
 {
 	/* ensure that an nRESET is not generated on resume. */
-	s3c2410_gpio_setpin(S3C2410_GPA21, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_OUT);
+	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
 
 	return 0;
 }
 
 static int bast_pm_resume(struct sys_device *sd)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT);
+	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
 	return 0;
 }
 
@@ -591,8 +592,6 @@ static void __init bast_map_io(void)
 	s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc));
 	s3c24xx_init_clocks(0);
 	s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs));
-
-	usb_simtec_init();
 }
 
 static void __init bast_init(void)
@@ -607,6 +606,7 @@ static void __init bast_init(void)
 	i2c_register_board_info(0, bast_i2c_devs,
 				ARRAY_SIZE(bast_i2c_devs));
 
+	usb_simtec_init();
 	nor_simtec_init();
 }
 

arch/arm/mach-s3c2410/mach-h1940.c

@@ -127,7 +127,7 @@ static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 
 static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = {
 	.udc_command		= h1940_udc_pullup,
-	.vbus_pin		= S3C2410_GPG5,
+	.vbus_pin		= S3C2410_GPG(5),
 	.vbus_pin_inverted	= 1,
 };
 

arch/arm/mach-s3c2410/mach-n30.c

@@ -19,6 +19,7 @@
 
 #include <linux/gpio_keys.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
@@ -85,10 +86,10 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 {
 	switch (cmd) {
 	case S3C2410_UDC_P_ENABLE :
-		s3c2410_gpio_setpin(S3C2410_GPB3, 1);
+		s3c2410_gpio_setpin(S3C2410_GPB(3), 1);
 		break;
 	case S3C2410_UDC_P_DISABLE :
-		s3c2410_gpio_setpin(S3C2410_GPB3, 0);
+		s3c2410_gpio_setpin(S3C2410_GPB(3), 0);
 		break;
 	case S3C2410_UDC_P_RESET :
 		break;
@@ -99,55 +100,55 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 
 static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = {
 	.udc_command		= n30_udc_pullup,
-	.vbus_pin		= S3C2410_GPG1,
+	.vbus_pin		= S3C2410_GPG(1),
 	.vbus_pin_inverted	= 0,
 };
 
 static struct gpio_keys_button n30_buttons[] = {
 	{
-		.gpio		= S3C2410_GPF0,
+		.gpio		= S3C2410_GPF(0),
 		.code		= KEY_POWER,
 		.desc		= "Power",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG9,
+		.gpio		= S3C2410_GPG(9),
 		.code		= KEY_UP,
 		.desc		= "Thumbwheel Up",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG8,
+		.gpio		= S3C2410_GPG(8),
 		.code		= KEY_DOWN,
 		.desc		= "Thumbwheel Down",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG7,
+		.gpio		= S3C2410_GPG(7),
 		.code		= KEY_ENTER,
 		.desc		= "Thumbwheel Press",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF7,
+		.gpio		= S3C2410_GPF(7),
 		.code		= KEY_HOMEPAGE,
 		.desc		= "Home",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF6,
+		.gpio		= S3C2410_GPF(6),
 		.code		= KEY_CALENDAR,
 		.desc		= "Calendar",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF5,
+		.gpio		= S3C2410_GPF(5),
 		.code		= KEY_ADDRESSBOOK,
 		.desc		= "Contacts",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF4,
+		.gpio		= S3C2410_GPF(4),
 		.code		= KEY_MAIL,
 		.desc		= "Mail",
 		.active_low	= 0,
@@ -169,73 +170,73 @@ static struct platform_device n30_button_device = {
 
 static struct gpio_keys_button n35_buttons[] = {
 	{
-		.gpio		= S3C2410_GPF0,
+		.gpio		= S3C2410_GPF(0),
 		.code		= KEY_POWER,
 		.desc		= "Power",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG9,
+		.gpio		= S3C2410_GPG(9),
 		.code		= KEY_UP,
 		.desc		= "Joystick Up",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG8,
+		.gpio		= S3C2410_GPG(8),
 		.code		= KEY_DOWN,
 		.desc		= "Joystick Down",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG6,
+		.gpio		= S3C2410_GPG(6),
 		.code		= KEY_DOWN,
 		.desc		= "Joystick Left",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG5,
+		.gpio		= S3C2410_GPG(5),
 		.code		= KEY_DOWN,
 		.desc		= "Joystick Right",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG7,
+		.gpio		= S3C2410_GPG(7),
 		.code		= KEY_ENTER,
 		.desc		= "Joystick Press",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF7,
+		.gpio		= S3C2410_GPF(7),
 		.code		= KEY_HOMEPAGE,
 		.desc		= "Home",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF6,
+		.gpio		= S3C2410_GPF(6),
 		.code		= KEY_CALENDAR,
 		.desc		= "Calendar",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF5,
+		.gpio		= S3C2410_GPF(5),
 		.code		= KEY_ADDRESSBOOK,
 		.desc		= "Contacts",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF4,
+		.gpio		= S3C2410_GPF(4),
 		.code		= KEY_MAIL,
 		.desc		= "Mail",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPF3,
+		.gpio		= S3C2410_GPF(3),
 		.code		= SW_RADIO,
 		.desc		= "GPS Antenna",
 		.active_low	= 0,
 	},
 	{
-		.gpio		= S3C2410_GPG2,
+		.gpio		= S3C2410_GPG(2),
 		.code		= SW_HEADPHONE_INSERT,
 		.desc		= "Headphone",
 		.active_low	= 0,
@@ -259,7 +260,7 @@ static struct platform_device n35_button_device = {
 /* This is the bluetooth LED on the device. */
 static struct s3c24xx_led_platdata n30_blue_led_pdata = {
 	.name		= "blue_led",
-	.gpio		= S3C2410_GPG6,
+	.gpio		= S3C2410_GPG(6),
 	.def_trigger	= "",
 };
 
@@ -270,7 +271,7 @@ static struct s3c24xx_led_platdata n30_blue_led_pdata = {
 static struct s3c24xx_led_platdata n30_warning_led_pdata = {
 	.name		= "warning_led",
 	.flags          = S3C24XX_LEDF_ACTLOW,
-	.gpio		= S3C2410_GPD9,
+	.gpio		= S3C2410_GPD(9),
 	.def_trigger	= "",
 };
 

arch/arm/mach-s3c2410/mach-qt2410.c

@@ -27,6 +27,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/sysdev.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
@@ -198,7 +199,7 @@ static struct platform_device qt2410_cs89x0 = {
 /* LED */
 
 static struct s3c24xx_led_platdata qt2410_pdata_led = {
-	.gpio		= S3C2410_GPB0,
+	.gpio		= S3C2410_GPB(0),
 	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
 	.name		= "led",
 	.def_trigger	= "timer",
@@ -218,18 +219,18 @@ static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs)
 {
 	switch (cs) {
 	case BITBANG_CS_ACTIVE:
-		s3c2410_gpio_setpin(S3C2410_GPB5, 0);
+		s3c2410_gpio_setpin(S3C2410_GPB(5), 0);
 		break;
 	case BITBANG_CS_INACTIVE:
-		s3c2410_gpio_setpin(S3C2410_GPB5, 1);
+		s3c2410_gpio_setpin(S3C2410_GPB(5), 1);
 		break;
 	}
 }
 
 static struct s3c2410_spigpio_info spi_gpio_cfg = {
-	.pin_clk	= S3C2410_GPG7,
-	.pin_mosi	= S3C2410_GPG6,
-	.pin_miso	= S3C2410_GPG5,
+	.pin_clk	= S3C2410_GPG(7),
+	.pin_mosi	= S3C2410_GPG(6),
+	.pin_miso	= S3C2410_GPG(5),
 	.chip_select	= &spi_gpio_cs,
 };
 
@@ -346,13 +347,13 @@ static void __init qt2410_machine_init(void)
 	}
 	s3c24xx_fb_set_platdata(&qt2410_fb_info);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB0, S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_setpin(S3C2410_GPB0, 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPB(0), 1);
 
 	s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
 	s3c_i2c0_set_platdata(NULL);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB5, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT);
 
 	platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices));
 	s3c_pm_init();

arch/arm/mach-s3c2410/mach-vr1000.c

@@ -18,6 +18,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/dm9000.h>
 #include <linux/i2c.h>
 
@@ -277,19 +278,19 @@ static struct platform_device vr1000_dm9k1 = {
 
 static struct s3c24xx_led_platdata vr1000_led1_pdata = {
 	.name		= "led1",
-	.gpio		= S3C2410_GPB0,
+	.gpio		= S3C2410_GPB(0),
 	.def_trigger	= "",
 };
 
 static struct s3c24xx_led_platdata vr1000_led2_pdata = {
 	.name		= "led2",
-	.gpio		= S3C2410_GPB1,
+	.gpio		= S3C2410_GPB(1),
 	.def_trigger	= "",
 };
 
 static struct s3c24xx_led_platdata vr1000_led3_pdata = {
 	.name		= "led3",
-	.gpio		= S3C2410_GPB2,
+	.gpio		= S3C2410_GPB(2),
 	.def_trigger	= "",
 };
 
@@ -355,8 +356,8 @@ static struct clk *vr1000_clocks[] __initdata = {
 
 static void vr1000_power_off(void)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPB9, S3C2410_GPB9_OUTP);
-	s3c2410_gpio_setpin(S3C2410_GPB9, 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPB(9), 1);
 }
 
 static void __init vr1000_map_io(void)

arch/arm/mach-s3c2410/pm.c

@@ -25,6 +25,7 @@
 #include <linux/errno.h>
 #include <linux/time.h>
 #include <linux/sysdev.h>
+#include <linux/gpio.h>
 #include <linux/io.h>
 
 #include <mach/hardware.h>
@@ -76,7 +77,7 @@ static void s3c2410_pm_prepare(void)
 	}
 
 	if ( machine_is_aml_m5900() )
-		s3c2410_gpio_setpin(S3C2410_GPF2, 1);
+		s3c2410_gpio_setpin(S3C2410_GPF(2), 1);
 
 }
 
@@ -91,7 +92,7 @@ static int s3c2410_pm_resume(struct sys_device *dev)
 	__raw_writel(tmp, S3C2410_GSTATUS2);
 
 	if ( machine_is_aml_m5900() )
-		s3c2410_gpio_setpin(S3C2410_GPF2, 0);
+		s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
 
 	return 0;
 }

arch/arm/mach-s3c2410/usb-simtec.c

@@ -18,9 +18,11 @@
 #include <linux/types.h>
 #include <linux/interrupt.h>
 #include <linux/list.h>
+#include <linux/gpio.h>
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/device.h>
+#include <linux/gpio.h>
 #include <linux/io.h>
 
 #include <asm/mach/arch.h>
@@ -29,7 +31,6 @@
 
 #include <mach/bast-map.h>
 #include <mach/bast-irq.h>
-#include <mach/regs-gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/irq.h>
@@ -53,9 +54,9 @@ usb_simtec_powercontrol(int port, int to)
 	power_state[port] = to;
 
 	if (power_state[0] && power_state[1])
-		s3c2410_gpio_setpin(S3C2410_GPB4, 0);
+		gpio_set_value(S3C2410_GPB(4), 0);
 	else
-		s3c2410_gpio_setpin(S3C2410_GPB4, 1);
+		gpio_set_value(S3C2410_GPB(4), 1);
 }
 
 static irqreturn_t
@@ -63,7 +64,7 @@ usb_simtec_ocirq(int irq, void *pw)
 {
 	struct s3c2410_hcd_info *info = pw;
 
-	if (s3c2410_gpio_getpin(S3C2410_GPG10) == 0) {
+	if (gpio_get_value(S3C2410_GPG(10)) == 0) {
 		pr_debug("usb_simtec: over-current irq (oc detected)\n");
 		s3c2410_usb_report_oc(info, 3);
 	} else {
@@ -106,10 +107,27 @@ static struct s3c2410_hcd_info usb_simtec_info = {
 
 int usb_simtec_init(void)
 {
+	int ret;
+
 	printk("USB Power Control, (c) 2004 Simtec Electronics\n");
-	s3c_device_usb.dev.platform_data = &usb_simtec_info;
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB4, S3C2410_GPB4_OUTP);
-	s3c2410_gpio_setpin(S3C2410_GPB4, 1);
+	ret = gpio_request(S3C2410_GPB(4), "USB power control");
+	if (ret < 0) {
+		pr_err("%s: failed to get GPB4\n", __func__);
+		return ret;
+	}
+
+	ret = gpio_request(S3C2410_GPG(10), "USB overcurrent");
+	if (ret < 0) {
+		pr_err("%s: failed to get GPG10\n", __func__);
+		gpio_free(S3C2410_GPB(4));
+		return ret;
+	}
+
+	/* turn power on */
+	gpio_direction_output(S3C2410_GPB(4), 1);
+	gpio_direction_input(S3C2410_GPG(10));
+
+	s3c_device_usb.dev.platform_data = &usb_simtec_info;
 	return 0;
 }

arch/arm/mach-s3c2412/Kconfig

@@ -38,6 +38,7 @@ menu "S3C2412 Machines"
 config MACH_JIVE
 	bool "Logitech Jive"
 	select CPU_S3C2412
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Logitech Jive.
 
@@ -50,6 +51,7 @@ config MACH_SMDK2413
 	select CPU_S3C2412
 	select MACH_S3C2413
 	select MACH_SMDK
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using an SMDK2413
 
@@ -72,6 +74,7 @@ config MACH_SMDK2412
 config MACH_VSTMS
 	bool "VMSTMS"
 	select CPU_S3C2412
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using an VSTMS board
 

arch/arm/mach-s3c2412/dma.c

@@ -20,12 +20,13 @@
 
 #include <mach/dma.h>
 
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
 #include <plat/cpu.h>
 
 #include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
 #include <mach/regs-mem.h>
 #include <mach/regs-lcd.h>
 #include <mach/regs-sdi.h>

arch/arm/mach-s3c2412/mach-jive.c

@@ -16,6 +16,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
@@ -356,8 +357,8 @@ static void jive_lcm_reset(unsigned int set)
 {
 	printk(KERN_DEBUG "%s(%d)\n", __func__, set);
 
-	s3c2410_gpio_setpin(S3C2410_GPG13, set);
-	s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPG(13), set);
+	s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
 }
 
 #undef LCD_UPPER_MARGIN
@@ -390,13 +391,13 @@ static struct ili9320_platdata jive_lcm_config = {
 
 static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
 {
-	s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1);
+	s3c2410_gpio_setpin(S3C2410_GPB(7), cs ? 0 : 1);
 }
 
 static struct s3c2410_spigpio_info jive_lcd_spi = {
 	.bus_num	= 1,
-	.pin_clk	= S3C2410_GPG8,
-	.pin_mosi	= S3C2410_GPB8,
+	.pin_clk	= S3C2410_GPG(8),
+	.pin_mosi	= S3C2410_GPB(8),
 	.num_chipselect	= 1,
 	.chip_select	= jive_lcd_spi_chipselect,
 };
@@ -412,13 +413,13 @@ static struct platform_device jive_device_lcdspi = {
 
 static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs)
 {
-	s3c2410_gpio_setpin(S3C2410_GPH10, cs ? 0 : 1);
+	s3c2410_gpio_setpin(S3C2410_GPH(10), cs ? 0 : 1);
 }
 
 static struct s3c2410_spigpio_info jive_wm8750_spi = {
 	.bus_num	= 2,
-	.pin_clk	= S3C2410_GPB4,
-	.pin_mosi	= S3C2410_GPB9,
+	.pin_clk	= S3C2410_GPB(4),
+	.pin_mosi	= S3C2410_GPB(9),
 	.num_chipselect	= 1,
 	.chip_select	= jive_wm8750_chipselect,
 };
@@ -479,7 +480,7 @@ static struct platform_device *jive_devices[] __initdata = {
 };
 
 static struct s3c2410_udc_mach_info jive_udc_cfg __initdata = {
-	.vbus_pin	= S3C2410_GPG1,		/* detect is on GPG1 */
+	.vbus_pin	= S3C2410_GPG(1),		/* detect is on GPG1 */
 };
 
 /* Jive power management device */
@@ -529,8 +530,8 @@ static void jive_power_off(void)
 {
 	printk(KERN_INFO "powering system down...\n");
 
-	s3c2410_gpio_setpin(S3C2410_GPC5, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPC5, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
 }
 
 static void __init jive_machine_init(void)
@@ -634,22 +635,22 @@ static void __init jive_machine_init(void)
 
 	/* initialise the spi */
 
-	s3c2410_gpio_setpin(S3C2410_GPG13, 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPG(13), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
 
-	s3c2410_gpio_setpin(S3C2410_GPB7, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPB(7), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(7), S3C2410_GPIO_OUTPUT);
 
-	s3c2410_gpio_setpin(S3C2410_GPB6, 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPB(6), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
 
-	s3c2410_gpio_setpin(S3C2410_GPG8, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPG(8), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT);
 
 	/* initialise the WM8750 spi */
 
-	s3c2410_gpio_setpin(S3C2410_GPH10, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH10, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPH(10), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPH(10), S3C2410_GPIO_OUTPUT);
 
 	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */

arch/arm/mach-s3c2412/mach-smdk2413.c

@@ -17,6 +17,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
@@ -84,10 +85,10 @@ static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 	switch (cmd)
 	{
 		case S3C2410_UDC_P_ENABLE :
-			s3c2410_gpio_setpin(S3C2410_GPF2, 1);
+			s3c2410_gpio_setpin(S3C2410_GPF(2), 1);
 			break;
 		case S3C2410_UDC_P_DISABLE :
-			s3c2410_gpio_setpin(S3C2410_GPF2, 0);
+			s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
 			break;
 		case S3C2410_UDC_P_RESET :
 			break;
@@ -134,8 +135,8 @@ static void __init smdk2413_machine_init(void)
 {	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */
 
-	s3c2410_gpio_setpin(S3C2410_GPF2, 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
 
 	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
 			      S3C2410_MISCCR_USBSUSPND0 |

arch/arm/mach-s3c2440/Kconfig

@@ -33,6 +33,7 @@ config MACH_ANUBIS
 	select PM_SIMTEC if PM
 	select HAVE_PATA_PLATFORM
 	select S3C24XX_GPIO_EXTRA64
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Simtec Electronics ANUBIS
 	  development system
@@ -43,6 +44,7 @@ config MACH_OSIRIS
 	select S3C24XX_DCLK
 	select PM_SIMTEC if PM
 	select S3C24XX_GPIO_EXTRA128
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Simtec IM2440D20 module, also
 	  known as the Osiris.
@@ -58,12 +60,14 @@ config ARCH_S3C2440
 	bool "SMDK2440"
 	select CPU_S3C2440
 	select MACH_SMDK
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the SMDK2440.
 
 config MACH_NEXCODER_2440
  	bool "NexVision NEXCODER 2440 Light Board"
  	select CPU_S3C2440
+	select S3C_DEV_USB_HOST
 	help
  	  Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
 
@@ -76,6 +80,7 @@ config SMDK2440_CPU2440
 config MACH_AT2440EVB
 	bool "Avantech AT2440EVB development board"
 	select CPU_S3C2440
+	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the AT2440EVB development board
 

arch/arm/mach-s3c2440/dma.c

@@ -17,14 +17,16 @@
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 
+#include <mach/map.h>
 #include <mach/dma.h>
 
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
 #include <plat/cpu.h>
 
 #include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
 #include <mach/regs-mem.h>
 #include <mach/regs-lcd.h>
 #include <mach/regs-sdi.h>

arch/arm/mach-s3c2440/mach-anubis.c

@@ -15,6 +15,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
 #include <linux/ata_platform.h>
@@ -468,7 +469,7 @@ static void __init anubis_map_io(void)
 		anubis_nand_sets[0].nr_partitions = ARRAY_SIZE(anubis_default_nand_part_large);
 	} else {
 		/* ensure that the GPIO is setup */
-		s3c2410_gpio_setpin(S3C2410_GPA0, 1);
+		s3c2410_gpio_setpin(S3C2410_GPA(0), 1);
 	}
 }
 

arch/arm/mach-s3c2440/mach-at2440evb.c

@@ -166,7 +166,7 @@ static struct platform_device at2440evb_device_eth = {
 };
 
 static struct s3c24xx_mci_pdata at2440evb_mci_pdata = {
-	.gpio_detect	= S3C2410_GPG10,
+	.gpio_detect	= S3C2410_GPG(10),
 };
 
 /* 7" LCD panel */

arch/arm/mach-s3c2440/mach-nexcoder.c

@@ -18,6 +18,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/string.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
@@ -120,16 +121,16 @@ static struct platform_device *nexcoder_devices[] __initdata = {
 static void __init nexcoder_sensorboard_init(void)
 {
 	// Initialize SCCB bus
-	s3c2410_gpio_setpin(S3C2410_GPE14, 1); // IICSCL
-	s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_OUTP);
-	s3c2410_gpio_setpin(S3C2410_GPE15, 1); // IICSDA
-	s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_OUTP);
+	s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL
+	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA
+	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
 
 	// Power up the sensor board
-	s3c2410_gpio_setpin(S3C2410_GPF1, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPF1, S3C2410_GPF1_OUTP); // CAM_GPIO7 => nLDO_PWRDN
-	s3c2410_gpio_setpin(S3C2410_GPF2, 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP); // CAM_GPIO6 => CAM_PWRDN
+	s3c2410_gpio_setpin(S3C2410_GPF(1), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
+	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
 }
 
 static void __init nexcoder_map_io(void)

arch/arm/mach-s3c2440/mach-osiris.c

@@ -15,6 +15,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/device.h>
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
@@ -291,8 +292,8 @@ static int osiris_pm_suspend(struct sys_device *sd, pm_message_t state)
 	__raw_writeb(tmp, OSIRIS_VA_CTRL0);
 
 	/* ensure that an nRESET is not generated on resume. */
-	s3c2410_gpio_setpin(S3C2410_GPA21, 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_OUT);
+	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
 
 	return 0;
 }
@@ -304,7 +305,7 @@ static int osiris_pm_resume(struct sys_device *sd)
 
 	__raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT);
+	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
 
 	return 0;
 }
@@ -384,7 +385,7 @@ static void __init osiris_map_io(void)
 		osiris_nand_sets[0].nr_partitions = ARRAY_SIZE(osiris_default_nand_part_large);
 	} else {
 		/* write-protect line to the NAND */
-		s3c2410_gpio_setpin(S3C2410_GPA0, 1);
+		s3c2410_gpio_setpin(S3C2410_GPA(0), 1);
 	}
 
 	/* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */

arch/arm/mach-s3c2443/dma.c

@@ -20,12 +20,13 @@
 
 #include <mach/dma.h>
 
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
 #include <plat/cpu.h>
 
 #include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
 #include <mach/regs-mem.h>
 #include <mach/regs-lcd.h>
 #include <mach/regs-sdi.h>

arch/arm/mach-s3c6400/Kconfig

@@ -5,4 +5,27 @@
 #
 # Licensed under GPLv2
 
-# Currently nothing here, this will be added later
+# Configuration options for the S3C6410 CPU
+
+config CPU_S3C6400
+	bool
+	select CPU_S3C6400_INIT
+	select CPU_S3C6400_CLOCK
+	help
+	  Enable S3C6400 CPU support
+
+config S3C6400_SETUP_SDHCI
+	bool
+	help
+	  Internal configuration for default SDHCI
+	  setup for S3C6400.
+
+# S36400 Macchine support
+
+config MACH_SMDK6400
+       bool "SMDK6400"
+	select CPU_S3C6400
+	select S3C_DEV_HSMMC
+	select S3C6400_SETUP_SDHCI
+	help
+	  Machine support for the Samsung SMDK6400

arch/arm/mach-s3c6400/Makefile

@@ -12,4 +12,12 @@ obj-				:=
 
 # Core support for S3C6400 system
 
-obj-n				+= blank.o
+obj-$(CONFIG_CPU_S3C6400)	+= s3c6400.o
+
+# setup support
+
+obj-$(CONFIG_S3C6400_SETUP_SDHCI) += setup-sdhci.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_SMDK6400)	+= mach-smdk6400.o

arch/arm/mach-s3c6400/include/mach/dma.h

@@ -11,6 +11,63 @@
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H __FILE__
 
-/* currently nothing here, placeholder */
+#define S3C_DMA_CHANNELS	(16)
+
+/* see mach-s3c2410/dma.h for notes on dma channel numbers */
+
+/* Note, for the S3C64XX architecture we keep the DMACH_
+ * defines in the order they are allocated to [S]DMA0/[S]DMA1
+ * so that is easy to do DHACH_ -> DMA controller conversion
+ */
+enum dma_ch {
+	/* DMA0/SDMA0 */
+	DMACH_UART0 = 0,
+	DMACH_UART0_SRC2,
+	DMACH_UART1,
+	DMACH_UART1_SRC2,
+	DMACH_UART2,
+	DMACH_UART2_SRC2,
+	DMACH_UART3,
+	DMACH_UART3_SRC2,
+	DMACH_PCM0_TX,
+	DMACH_PCM0_RX,
+	DMACH_I2S0_OUT,
+	DMACH_I2S0_IN,
+	DMACH_SPI0_TX,
+	DMACH_SPI0_RX,
+	DMACH_HSI_I2SV40_TX,
+	DMACH_HSI_I2SV40_RX,
+
+	/* DMA1/SDMA1 */
+	DMACH_PCM1_TX = 16,
+	DMACH_PCM1_RX,
+	DMACH_I2S1_OUT,
+	DMACH_I2S1_IN,
+	DMACH_SPI1_TX,
+	DMACH_SPI1_RX,
+	DMACH_AC97_PCMOUT,
+	DMACH_AC97_PCMIN,
+	DMACH_AC97_MICIN,
+	DMACH_PWM,
+	DMACH_IRDA,
+	DMACH_EXTERNAL,
+	DMACH_RES1,
+	DMACH_RES2,
+	DMACH_SECURITY_RX,	/* SDMA1 only */
+	DMACH_SECURITY_TX,	/* SDMA1 only */
+	DMACH_MAX		/* the end */
+};
+
+static __inline__ int s3c_dma_has_circular(void)
+{
+	/* we will be supporting ciruclar buffers as soon as we have DMA
+	 * engine support.
+	 */
+	return 1;
+}
+
+#define S3C2410_DMAF_CIRCULAR		(1 << 0)
+
+#include <plat/dma.h>
 
 #endif /* __ASM_ARCH_IRQ_H */

arch/arm/mach-s3c6400/include/mach/map.h

@@ -39,6 +39,8 @@
 #define S3C_VA_UART3		S3C_VA_UARTx(3)
 
 #define S3C64XX_PA_FB		(0x77100000)
+#define S3C64XX_PA_USB_HSOTG	(0x7C000000)
+#define S3C64XX_PA_WATCHDOG	(0x7E004000)
 #define S3C64XX_PA_SYSCON	(0x7E00F000)
 #define S3C64XX_PA_IIS0		(0x7F002000)
 #define S3C64XX_PA_IIS1		(0x7F003000)
@@ -57,6 +59,8 @@
 #define S3C64XX_PA_MODEM	(0x74108000)
 #define S3C64XX_VA_MODEM	S3C_ADDR(0x00600000)
 
+#define S3C64XX_PA_USBHOST	(0x74300000)
+
 /* place VICs close together */
 #define S3C_VA_VIC0		(S3C_VA_IRQ + 0x00)
 #define S3C_VA_VIC1		(S3C_VA_IRQ + 0x10000)
@@ -69,5 +73,7 @@
 #define S3C_PA_IIC		S3C64XX_PA_IIC0
 #define S3C_PA_IIC1		S3C64XX_PA_IIC1
 #define S3C_PA_FB		S3C64XX_PA_FB
+#define S3C_PA_USBHOST		S3C64XX_PA_USBHOST
+#define S3C_PA_USB_HSOTG	S3C64XX_PA_USB_HSOTG
 
 #endif /* __ASM_ARCH_6400_MAP_H */

arch/arm/mach-s3c6400/include/mach/regs-clock.h

+/* linux/arch/arm/mach-s3c6400/include/mach/regs-clock.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C64XX - clock register compatibility with s3c24xx
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <plat/regs-clock.h>
+

arch/arm/mach-s3c6400/include/mach/system.h

@@ -11,6 +11,8 @@
 #ifndef __ASM_ARCH_SYSTEM_H
 #define __ASM_ARCH_SYSTEM_H __FILE__
 
+#include <plat/watchdog-reset.h>
+
 static void arch_idle(void)
 {
 	/* nothing here yet */
@@ -18,7 +20,11 @@ static void arch_idle(void)
 
 static void arch_reset(char mode, const char *cmd)
 {
-	/* nothing here yet */
+	if (mode != 's')
+		arch_wdt_reset();
+
+	/* if all else fails, or mode was for soft, jump to 0 */
+	cpu_reset(0);
 }
 
 #endif /* __ASM_ARCH_IRQ_H */

arch/arm/mach-s3c6400/mach-smdk6400.c

+/* linux/arch/arm/mach-s3c6400/mach-smdk6400.c
+ *
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+
+#include <asm/mach-types.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/map.h>
+
+#include <plat/regs-serial.h>
+
+#include <plat/s3c6400.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/iic.h>
+
+#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg smdk6400_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+};
+
+static struct map_desc smdk6400_iodesc[] = {};
+
+static void __init smdk6400_map_io(void)
+{
+	s3c64xx_init_io(smdk6400_iodesc, ARRAY_SIZE(smdk6400_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(smdk6400_uartcfgs, ARRAY_SIZE(smdk6400_uartcfgs));
+}
+
+static struct platform_device *smdk6400_devices[] __initdata = {
+	&s3c_device_hsmmc1,
+	&s3c_device_i2c0,
+};
+
+static struct i2c_board_info i2c_devs[] __initdata = {
+	{ I2C_BOARD_INFO("wm8753", 0x1A), },
+	{ I2C_BOARD_INFO("24c08", 0x50), },
+};
+
+static void __init smdk6400_machine_init(void)
+{
+	i2c_register_board_info(0, i2c_devs, ARRAY_SIZE(i2c_devs));
+	platform_add_devices(smdk6400_devices, ARRAY_SIZE(smdk6400_devices));
+}
+
+MACHINE_START(SMDK6400, "SMDK6400")
+	/* Maintainer: Ben Dooks <ben@fluff.org> */
+	.phys_io	= S3C_PA_UART & 0xfff00000,
+	.io_pg_offst	= (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+
+	.init_irq	= s3c6400_init_irq,
+	.map_io		= smdk6400_map_io,
+	.init_machine	= smdk6400_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mach-s3c6400/s3c6400.c

+/* linux/arch/arm/mach-s3c6410/cpu.c
+ *
+ * Copyright 2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/sysdev.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <plat/cpu-freq.h>
+#include <plat/regs-serial.h>
+#include <plat/regs-clock.h>
+
+#include <plat/cpu.h>
+#include <plat/devs.h>
+#include <plat/clock.h>
+#include <plat/sdhci.h>
+#include <plat/iic-core.h>
+#include <plat/s3c6400.h>
+
+void __init s3c6400_map_io(void)
+{
+	/* setup SDHCI */
+
+	s3c6400_default_sdhci0();
+	s3c6400_default_sdhci1();
+
+	/* the i2c devices are directly compatible with s3c2440 */
+	s3c_i2c0_setname("s3c2440-i2c");
+}
+
+void __init s3c6400_init_clocks(int xtal)
+{
+	printk(KERN_DEBUG "%s: initialising clocks\n", __func__);
+	s3c24xx_register_baseclocks(xtal);
+	s3c64xx_register_clocks();
+	s3c6400_register_clocks(S3C6400_CLKDIV0_ARM_MASK);
+	s3c6400_setup_clocks();
+}
+
+void __init s3c6400_init_irq(void)
+{
+	/* VIC0 does not have IRQS 5..7,
+	 * VIC1 is fully populated. */
+	s3c64xx_init_irq(~0 & ~(0xf << 5), ~0);
+}
+
+struct sysdev_class s3c6400_sysclass = {
+	.name	= "s3c6400-core",
+};
+
+static struct sys_device s3c6400_sysdev = {
+	.cls	= &s3c6400_sysclass,
+};
+
+static int __init s3c6400_core_init(void)
+{
+	return sysdev_class_register(&s3c6400_sysclass);
+}
+
+core_initcall(s3c6400_core_init);
+
+int __init s3c6400_init(void)
+{
+	printk("S3C6400: Initialising architecture\n");
+
+	return sysdev_register(&s3c6400_sysdev);
+}

arch/arm/mach-s3c6400/setup-sdhci.c

+/* linux/arch/arm/mach-s3c6410/setup-sdhci.c
+ *
+ * Copyright 2008 Simtec Electronics
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C6410 - Helper functions for settign up SDHCI device(s) (HSMMC)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+
+#include <plat/regs-sdhci.h>
+#include <plat/sdhci.h>
+
+/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
+
+char *s3c6400_hsmmc_clksrcs[4] = {
+	[0] = "hsmmc",
+	[1] = "hsmmc",
+	[2] = "mmc_bus",
+	/* [3] = "48m", - note not succesfully used yet */
+};
+
+void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev,
+				  void __iomem *r,
+				  struct mmc_ios *ios,
+				  struct mmc_card *card)
+{
+	u32 ctrl2, ctrl3;
+
+	ctrl2 = readl(r + S3C_SDHCI_CONTROL2);
+	ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
+	ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
+		  S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
+		  S3C_SDHCI_CTRL2_ENFBCLKRX |
+		  S3C_SDHCI_CTRL2_DFCNT_NONE |
+		  S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
+
+	if (ios->clock < 25 * 1000000)
+		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
+			 S3C_SDHCI_CTRL3_FCSEL2 |
+			 S3C_SDHCI_CTRL3_FCSEL1 |
+			 S3C_SDHCI_CTRL3_FCSEL0);
+	else
+		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
+
+	printk(KERN_INFO "%s: CTRL 2=%08x, 3=%08x\n", __func__, ctrl2, ctrl3);
+	writel(ctrl2, r + S3C_SDHCI_CONTROL2);
+	writel(ctrl3, r + S3C_SDHCI_CONTROL3);
+}
+

arch/arm/mach-s3c6410/Kconfig

@@ -16,9 +16,18 @@ config CPU_S3C6410
 
 config S3C6410_SETUP_SDHCI
 	bool
+	select S3C64XX_SETUP_SDHCI_GPIO
 	help
 	  Internal helper functions for S3C6410 based SDHCI systems
 
+config MACH_ANW6410
+	bool "A&W6410"
+	select CPU_S3C6410
+	select S3C_DEV_FB
+	select S3C64XX_SETUP_FB_24BPP
+	help
+	  Machine support for the A&W6410
+
 config MACH_SMDK6410
 	bool "SMDK6410"
 	select CPU_S3C6410
@@ -26,6 +35,8 @@ config MACH_SMDK6410
 	select S3C_DEV_HSMMC1
 	select S3C_DEV_I2C1
 	select S3C_DEV_FB
+	select S3C_DEV_USB_HOST
+	select S3C_DEV_USB_HSOTG
 	select S3C6410_SETUP_SDHCI
 	select S3C64XX_SETUP_I2C1
 	select S3C64XX_SETUP_FB_24BPP
@@ -60,3 +71,29 @@ config SMDK6410_SD_CH1
 	  channels 0 and 1 are the same.
 
 endchoice
+
+config SMDK6410_WM1190_EV1
+	bool "Support Wolfson Microelectronics 1190-EV1 PMIC card"
+	depends on MACH_SMDK6410
+	select REGULATOR
+	select REGULATOR_WM8350
+	select MFD_WM8350_I2C
+	select MFD_WM8350_CONFIG_MODE_0
+	select MFD_WM8350_CONFIG_MODE_3
+	select MFD_WM8352_CONFIG_MODE_0
+	help
+	  The Wolfson Microelectronics 1190-EV1 is a WM835x based PMIC
+	  and audio daughtercard for the Samsung SMDK6410 reference
+	  platform.  Enabling this option will build support for this
+	  module into the kernel.  The presence of the module will be
+	  detected at runtime so the the resulting kernel can be used
+	  with or without the 1190-EV1 fitted.
+
+config MACH_NCP
+	bool "NCP"
+	select CPU_S3C6410
+	select S3C_DEV_I2C1
+	select S3C_DEV_HSMMC1
+	select S3C64XX_SETUP_I2C1
+	help
+          Machine support for the Samsung NCP

arch/arm/mach-s3c6410/Makefile

@@ -20,4 +20,8 @@ obj-$(CONFIG_S3C6410_SETUP_SDHCI)	+= setup-sdhci.o
 
 # machine support
 
+obj-$(CONFIG_MACH_ANW6410)	+= mach-anw6410.o
 obj-$(CONFIG_MACH_SMDK6410)	+= mach-smdk6410.o
+obj-$(CONFIG_MACH_NCP)		+= mach-ncp.o
+
+

arch/arm/mach-s3c6410/cpu.c

@@ -31,6 +31,7 @@
 
 #include <plat/cpu-freq.h>
 #include <plat/regs-serial.h>
+#include <plat/regs-clock.h>
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
@@ -68,7 +69,7 @@ void __init s3c6410_init_clocks(int xtal)
 	printk(KERN_DEBUG "%s: initialising clocks\n", __func__);
 	s3c24xx_register_baseclocks(xtal);
 	s3c64xx_register_clocks();
-	s3c6400_register_clocks();
+	s3c6400_register_clocks(S3C6410_CLKDIV0_ARM_MASK);
 	s3c6400_setup_clocks();
 }
 

arch/arm/mach-s3c6410/mach-anw6410.c

+/* linux/arch/arm/mach-s3c6410/mach-anw6410.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ * Copyright 2009 Kwangwoo Lee
+ * 	Kwangwoo Lee <kwangwoo.lee@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/dm9000.h>
+
+#include <video/platform_lcd.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/regs-fb.h>
+#include <mach/map.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <plat/iic.h>
+#include <plat/fb.h>
+
+#include <plat/s3c6410.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-modem.h>
+
+/* DM9000 */
+#define ANW6410_PA_DM9000	(0x18000000)
+
+/* A hardware buffer to control external devices is mapped at 0x30000000.
+ * It can not be read. So current status must be kept in anw6410_extdev_status.
+ */
+#define ANW6410_VA_EXTDEV	S3C_ADDR(0x02000000)
+#define ANW6410_PA_EXTDEV	(0x30000000)
+
+#define ANW6410_EN_DM9000	(1<<11)
+#define ANW6410_EN_LCD		(1<<14)
+
+static __u32 anw6410_extdev_status;
+
+static struct s3c2410_uartcfg anw6410_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+};
+
+/* framebuffer and LCD setup. */
+static void __init anw6410_lcd_mode_set(void)
+{
+	u32 tmp;
+
+	/* set the LCD type */
+	tmp = __raw_readl(S3C64XX_SPCON);
+	tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK;
+	tmp |= S3C64XX_SPCON_LCD_SEL_RGB;
+	__raw_writel(tmp, S3C64XX_SPCON);
+
+	/* remove the LCD bypass */
+	tmp = __raw_readl(S3C64XX_MODEM_MIFPCON);
+	tmp &= ~MIFPCON_LCD_BYPASS;
+	__raw_writel(tmp, S3C64XX_MODEM_MIFPCON);
+}
+
+/* GPF1 = LCD panel power
+ * GPF4 = LCD backlight control
+ */
+static void anw6410_lcd_power_set(struct plat_lcd_data *pd,
+				   unsigned int power)
+{
+	if (power) {
+		anw6410_extdev_status |= (ANW6410_EN_LCD << 16);
+		__raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV);
+
+		gpio_direction_output(S3C64XX_GPF(1), 1);
+		gpio_direction_output(S3C64XX_GPF(4), 1);
+	} else {
+		anw6410_extdev_status &= ~(ANW6410_EN_LCD << 16);
+		__raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV);
+
+		gpio_direction_output(S3C64XX_GPF(1), 0);
+		gpio_direction_output(S3C64XX_GPF(4), 0);
+	}
+}
+
+static struct plat_lcd_data anw6410_lcd_power_data = {
+	.set_power	= anw6410_lcd_power_set,
+};
+
+static struct platform_device anw6410_lcd_powerdev = {
+	.name			= "platform-lcd",
+	.dev.parent		= &s3c_device_fb.dev,
+	.dev.platform_data	= &anw6410_lcd_power_data,
+};
+
+static struct s3c_fb_pd_win anw6410_fb_win0 = {
+	/* this is to ensure we use win0 */
+	.win_mode	= {
+		.pixclock	= 41094,
+		.left_margin	= 8,
+		.right_margin	= 13,
+		.upper_margin	= 7,
+		.lower_margin	= 5,
+		.hsync_len	= 3,
+		.vsync_len	= 1,
+		.xres		= 800,
+		.yres		= 480,
+	},
+	.max_bpp	= 32,
+	.default_bpp	= 16,
+};
+
+/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */
+static struct s3c_fb_platdata anw6410_lcd_pdata __initdata = {
+	.setup_gpio	= s3c64xx_fb_gpio_setup_24bpp,
+	.win[0]		= &anw6410_fb_win0,
+	.vidcon0	= VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
+	.vidcon1	= VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
+};
+
+/* DM9000AEP 10/100 ethernet controller */
+static void __init anw6410_dm9000_enable(void)
+{
+	anw6410_extdev_status |= (ANW6410_EN_DM9000 << 16);
+	__raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV);
+}
+
+static struct resource anw6410_dm9000_resource[] = {
+	[0] = {
+		.start = ANW6410_PA_DM9000,
+		.end   = ANW6410_PA_DM9000 + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = ANW6410_PA_DM9000 + 4,
+		.end   = ANW6410_PA_DM9000 + 4 + 500,
+		.flags = IORESOURCE_MEM,
+	},
+	[2] = {
+		.start = IRQ_EINT(15),
+		.end   = IRQ_EINT(15),
+		.flags = IORESOURCE_IRQ | IRQF_TRIGGER_HIGH,
+	},
+};
+
+static struct dm9000_plat_data anw6410_dm9000_pdata = {
+	.flags	  = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
+	/* dev_addr can be set to provide hwaddr. */
+};
+
+static struct platform_device anw6410_device_eth = {
+	.name	= "dm9000",
+	.id	= -1,
+	.num_resources	= ARRAY_SIZE(anw6410_dm9000_resource),
+	.resource	= anw6410_dm9000_resource,
+	.dev	= {
+		.platform_data  = &anw6410_dm9000_pdata,
+	},
+};
+
+static struct map_desc anw6410_iodesc[] __initdata = {
+	{
+		.virtual	= (unsigned long)ANW6410_VA_EXTDEV,
+		.pfn		= __phys_to_pfn(ANW6410_PA_EXTDEV),
+		.length		= SZ_64K,
+		.type		= MT_DEVICE,
+	},
+};
+
+static struct platform_device *anw6410_devices[] __initdata = {
+	&s3c_device_fb,
+	&anw6410_lcd_powerdev,
+	&anw6410_device_eth,
+};
+
+static void __init anw6410_map_io(void)
+{
+	s3c64xx_init_io(anw6410_iodesc, ARRAY_SIZE(anw6410_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(anw6410_uartcfgs, ARRAY_SIZE(anw6410_uartcfgs));
+
+	anw6410_lcd_mode_set();
+}
+
+static void __init anw6410_machine_init(void)
+{
+	s3c_fb_set_platdata(&anw6410_lcd_pdata);
+
+	gpio_request(S3C64XX_GPF(1), "panel power");
+	gpio_request(S3C64XX_GPF(4), "LCD backlight");
+
+	anw6410_dm9000_enable();
+
+	platform_add_devices(anw6410_devices, ARRAY_SIZE(anw6410_devices));
+}
+
+MACHINE_START(ANW6410, "A&W6410")
+	/* Maintainer: Kwangwoo Lee <kwangwoo.lee@gmail.com> */
+	.phys_io	= S3C_PA_UART & 0xfff00000,
+	.io_pg_offst	= (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+
+	.init_irq	= s3c6410_init_irq,
+	.map_io		= anw6410_map_io,
+	.init_machine	= anw6410_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mach-s3c6410/mach-ncp.c

+/*
+ * linux/arch/arm/mach-s3c6410/mach-ncp.c
+ *
+ * Copyright (C) 2008-2009 Samsung Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+
+#include <video/platform_lcd.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/regs-fb.h>
+#include <mach/map.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <plat/iic.h>
+#include <plat/fb.h>
+
+#include <plat/s3c6410.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg ncp_uartcfgs[] __initdata = {
+	/* REVISIT: NCP uses only serial 1, 2 */
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+};
+
+static struct platform_device *ncp_devices[] __initdata = {
+	&s3c_device_hsmmc1,
+	&s3c_device_i2c0,
+};
+
+struct map_desc ncp_iodesc[] = {};
+
+static void __init ncp_map_io(void)
+{
+	s3c64xx_init_io(ncp_iodesc, ARRAY_SIZE(ncp_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(ncp_uartcfgs, ARRAY_SIZE(ncp_uartcfgs));
+}
+
+static void __init ncp_machine_init(void)
+{
+	s3c_i2c0_set_platdata(NULL);
+
+	platform_add_devices(ncp_devices, ARRAY_SIZE(ncp_devices));
+}
+
+MACHINE_START(NCP, "NCP")
+	/* Maintainer: Samsung Electronics */
+	.phys_io	= S3C_PA_UART & 0xfff00000,
+	.io_pg_offst	= (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.init_irq	= s3c6410_init_irq,
+	.map_io		= ncp_map_io,
+	.init_machine	= ncp_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mach-s3c6410/mach-smdk6410.c

@@ -24,6 +24,12 @@
 #include <linux/fb.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
+#include <linux/smsc911x.h>
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+#include <linux/mfd/wm8350/core.h>
+#include <linux/mfd/wm8350/pmic.h>
+#endif
 
 #include <video/platform_lcd.h>
 
@@ -39,8 +45,12 @@
 #include <asm/mach-types.h>
 
 #include <plat/regs-serial.h>
+#include <plat/regs-modem.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-sys.h>
 #include <plat/iic.h>
 #include <plat/fb.h>
+#include <plat/gpio-cfg.h>
 
 #include <plat/s3c6410.h>
 #include <plat/clock.h>
@@ -129,6 +139,37 @@ static struct s3c_fb_platdata smdk6410_lcd_pdata __initdata = {
 	.vidcon1	= VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
 };
 
+static struct resource smdk6410_smsc911x_resources[] = {
+	[0] = {
+		.start = 0x18000000,
+		.end   = 0x18000000 + SZ_64K - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = S3C_EINT(10),
+		.end   = S3C_EINT(10),
+		.flags = IORESOURCE_IRQ | IRQ_TYPE_LEVEL_LOW,
+	},
+};
+
+static struct smsc911x_platform_config smdk6410_smsc911x_pdata = {
+	.irq_polarity  = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type      = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.flags         = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
+	.phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+
+static struct platform_device smdk6410_smsc911x = {
+	.name          = "smsc911x",
+	.id            = -1,
+	.num_resources = ARRAY_SIZE(smdk6410_smsc911x_resources),
+	.resource      = &smdk6410_smsc911x_resources[0],
+	.dev = {
+		.platform_data = &smdk6410_smsc911x_pdata,
+	},
+};
+
 static struct map_desc smdk6410_iodesc[] = {};
 
 static struct platform_device *smdk6410_devices[] __initdata = {
@@ -141,12 +182,155 @@ static struct platform_device *smdk6410_devices[] __initdata = {
 	&s3c_device_i2c0,
 	&s3c_device_i2c1,
 	&s3c_device_fb,
+	&s3c_device_usb,
+	&s3c_device_usb_hsotg,
 	&smdk6410_lcd_powerdev,
+
+	&smdk6410_smsc911x,
+};
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+/* S3C64xx internal logic & PLL */
+static struct regulator_init_data wm8350_dcdc1_data = {
+	.constraints = {
+		.name = "PVDD_INT/PVDD_PLL",
+		.min_uV = 1200000,
+		.max_uV = 1200000,
+		.always_on = 1,
+		.apply_uV = 1,
+	},
+};
+
+/* Memory */
+static struct regulator_init_data wm8350_dcdc3_data = {
+	.constraints = {
+		.name = "PVDD_MEM",
+		.min_uV = 1800000,
+		.max_uV = 1800000,
+		.always_on = 1,
+		.state_mem = {
+			 .uV = 1800000,
+			 .mode = REGULATOR_MODE_NORMAL,
+			 .enabled = 1,
+		 },
+		.initial_state = PM_SUSPEND_MEM,
+	},
+};
+
+/* USB, EXT, PCM, ADC/DAC, USB, MMC */
+static struct regulator_init_data wm8350_dcdc4_data = {
+	.constraints = {
+		.name = "PVDD_HI/PVDD_EXT/PVDD_SYS/PVCCM2MTV",
+		.min_uV = 3000000,
+		.max_uV = 3000000,
+		.always_on = 1,
+	},
+};
+
+/* ARM core */
+static struct regulator_consumer_supply dcdc6_consumers[] = {
+	{
+		.supply = "vddarm",
+	}
+};
+
+static struct regulator_init_data wm8350_dcdc6_data = {
+	.constraints = {
+		.name = "PVDD_ARM",
+		.min_uV = 1000000,
+		.max_uV = 1300000,
+		.always_on = 1,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(dcdc6_consumers),
+	.consumer_supplies = dcdc6_consumers,
 };
 
+/* Alive */
+static struct regulator_init_data wm8350_ldo1_data = {
+	.constraints = {
+		.name = "PVDD_ALIVE",
+		.min_uV = 1200000,
+		.max_uV = 1200000,
+		.always_on = 1,
+		.apply_uV = 1,
+	},
+};
+
+/* OTG */
+static struct regulator_init_data wm8350_ldo2_data = {
+	.constraints = {
+		.name = "PVDD_OTG",
+		.min_uV = 3300000,
+		.max_uV = 3300000,
+		.always_on = 1,
+	},
+};
+
+/* LCD */
+static struct regulator_init_data wm8350_ldo3_data = {
+	.constraints = {
+		.name = "PVDD_LCD",
+		.min_uV = 3000000,
+		.max_uV = 3000000,
+		.always_on = 1,
+	},
+};
+
+/* OTGi/1190-EV1 HPVDD & AVDD */
+static struct regulator_init_data wm8350_ldo4_data = {
+	.constraints = {
+		.name = "PVDD_OTGI/HPVDD/AVDD",
+		.min_uV = 1200000,
+		.max_uV = 1200000,
+		.apply_uV = 1,
+		.always_on = 1,
+	},
+};
+
+static struct {
+	int regulator;
+	struct regulator_init_data *initdata;
+} wm1190_regulators[] = {
+	{ WM8350_DCDC_1, &wm8350_dcdc1_data },
+	{ WM8350_DCDC_3, &wm8350_dcdc3_data },
+	{ WM8350_DCDC_4, &wm8350_dcdc4_data },
+	{ WM8350_DCDC_6, &wm8350_dcdc6_data },
+	{ WM8350_LDO_1, &wm8350_ldo1_data },
+	{ WM8350_LDO_2, &wm8350_ldo2_data },
+	{ WM8350_LDO_3, &wm8350_ldo3_data },
+	{ WM8350_LDO_4, &wm8350_ldo4_data },
+};
+
+static int __init smdk6410_wm8350_init(struct wm8350 *wm8350)
+{
+	int i;
+
+	/* Instantiate the regulators */
+	for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++)
+		wm8350_register_regulator(wm8350,
+					  wm1190_regulators[i].regulator,
+					  wm1190_regulators[i].initdata);
+
+	return 0;
+}
+
+static struct wm8350_platform_data __initdata smdk6410_wm8350_pdata = {
+	.init = smdk6410_wm8350_init,
+	.irq_high = 1,
+};
+#endif
+
 static struct i2c_board_info i2c_devs0[] __initdata = {
 	{ I2C_BOARD_INFO("24c08", 0x50), },
 	{ I2C_BOARD_INFO("wm8580", 0x1b), },
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+	{ I2C_BOARD_INFO("wm8350", 0x1a),
+	  .platform_data = &smdk6410_wm8350_pdata,
+	  .irq = S3C_EINT(12),
+	},
+#endif
 };
 
 static struct i2c_board_info i2c_devs1[] __initdata = {
@@ -155,9 +339,23 @@ static struct i2c_board_info i2c_devs1[] __initdata = {
 
 static void __init smdk6410_map_io(void)
 {
+	u32 tmp;
+
 	s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
 	s3c24xx_init_clocks(12000000);
 	s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
+
+	/* set the LCD type */
+
+	tmp = __raw_readl(S3C64XX_SPCON);
+	tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK;
+	tmp |= S3C64XX_SPCON_LCD_SEL_RGB;
+	__raw_writel(tmp, S3C64XX_SPCON);
+
+	/* remove the lcd bypass */
+	tmp = __raw_readl(S3C64XX_MODEM_MIFPCON);
+	tmp &= ~MIFPCON_LCD_BYPASS;
+	__raw_writel(tmp, S3C64XX_MODEM_MIFPCON);
 }
 
 static void __init smdk6410_machine_init(void)

arch/arm/mach-s3c6410/setup-sdhci.c

@@ -21,8 +21,6 @@
 #include <linux/mmc/card.h>
 #include <linux/mmc/host.h>
 
-#include <mach/gpio.h>
-#include <plat/gpio-cfg.h>
 #include <plat/regs-sdhci.h>
 #include <plat/sdhci.h>
 
@@ -35,22 +33,6 @@ char *s3c6410_hsmmc_clksrcs[4] = {
 	/* [3] = "48m", - note not succesfully used yet */
 };
 
-void s3c6410_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
-{
-	unsigned int gpio;
-	unsigned int end;
-
-	end = S3C64XX_GPG(2 + width);
-
-	/* Set all the necessary GPG pins to special-function 0 */
-	for (gpio = S3C64XX_GPG(0); gpio < end; gpio++) {
-		s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
-		s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
-	}
-
-	s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
-	s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(2));
-}
 
 void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev,
 				    void __iomem *r,
@@ -84,19 +66,3 @@ void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev,
 	writel(ctrl3, r + S3C_SDHCI_CONTROL3);
 }
 
-void s3c6410_setup_sdhci1_cfg_gpio(struct platform_device *dev, int width)
-{
-	unsigned int gpio;
-	unsigned int end;
-
-	end = S3C64XX_GPH(2 + width);
-
-	/* Set all the necessary GPG pins to special-function 0 */
-	for (gpio = S3C64XX_GPH(0); gpio < end; gpio++) {
-		s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
-		s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
-	}
-
-	s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
-	s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(3));
-}

arch/arm/mach-versatile/core.c

@@ -116,7 +116,7 @@ void __init versatile_init_irq(void)
 {
 	unsigned int i;
 
-	vic_init(VA_VIC_BASE, IRQ_VIC_START, ~0);
+	vic_init(VA_VIC_BASE, IRQ_VIC_START, ~0, 0);
 
 	set_irq_chained_handler(IRQ_VICSOURCE31, sic_handle_irq);
 

arch/arm/plat-s3c/Kconfig

@@ -71,6 +71,15 @@ config S3C2410_PM_DEBUG
 	  Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
 	  for more information.
 
+config S3C_PM_DEBUG_LED_SMDK
+       bool "SMDK LED suspend/resume debugging"
+       depends on PM && (MACH_SMDK6410)
+       help
+         Say Y here to enable the use of the SMDK LEDs on the baseboard
+	 for debugging of the state of the suspend and resume process.
+
+	 Note, this currently only works for S3C64XX based SMDK boards.
+
 config S3C2410_PM_CHECK
 	bool "S3C2410 PM Suspend Memory CRC"
 	depends on PM && CRC32
@@ -150,6 +159,13 @@ config S3C_GPIO_CFG_S3C64XX
 	  Internal configuration to enable S3C64XX style GPIO configuration
 	  functions.
 
+# DMA
+
+config S3C_DMA
+	bool
+	help
+	  Internal configuration for S3C DMA core
+
 # device definitions to compile in
 
 config S3C_DEV_HSMMC
@@ -172,4 +188,14 @@ config S3C_DEV_FB
 	help
 	  Compile in platform device definition for framebuffer
 
+config S3C_DEV_USB_HOST
+	bool
+	help
+	  Compile in platform device definition for USB host.
+
+config S3C_DEV_USB_HSOTG
+	bool
+	help
+	  Compile in platform device definition for USB high-speed OtG
+
 endif

arch/arm/plat-s3c/Makefile

@@ -18,9 +18,14 @@ obj-y				+= pwm-clock.o
 obj-y				+= gpio.o
 obj-y				+= gpio-config.o
 
+# DMA support
+
+obj-$(CONFIG_S3C_DMA)		+= dma.o
+
 # PM support
 
 obj-$(CONFIG_PM)		+= pm.o
+obj-$(CONFIG_PM)		+= pm-gpio.o
 obj-$(CONFIG_S3C2410_PM_CHECK)	+= pm-check.o
 
 # devices
@@ -30,3 +35,5 @@ obj-$(CONFIG_S3C_DEV_HSMMC1)	+= dev-hsmmc1.o
 obj-y				+= dev-i2c0.o
 obj-$(CONFIG_S3C_DEV_I2C1)	+= dev-i2c1.o
 obj-$(CONFIG_S3C_DEV_FB)	+= dev-fb.o
+obj-$(CONFIG_S3C_DEV_USB_HOST)	+= dev-usb.o
+obj-$(CONFIG_S3C_DEV_USB_HSOTG)	+= dev-usb-hsotg.o

arch/arm/plat-s3c/dev-usb-hsotg.c

+/* linux/arch/arm/plat-s3c/dev-usb-hsotg.c
+ *
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C series device definition for USB high-speed UDC/OtG block
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+static struct resource s3c_usb_hsotg_resources[] = {
+	[0] = {
+		.start	= S3C_PA_USB_HSOTG,
+		.end	= S3C_PA_USB_HSOTG + 0x10000 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_OTG,
+		.end	= IRQ_OTG,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device s3c_device_usb_hsotg = {
+	.name		= "s3c-hsotg",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_usb_hsotg_resources),
+	.resource	= s3c_usb_hsotg_resources,
+};

arch/arm/plat-s3c/dev-usb.c

+/* linux/arch/arm/plat-s3c/dev-usb.c
+ *
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C series device definition for USB host
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+
+static struct resource s3c_usb_resource[] = {
+	[0] = {
+		.start = S3C_PA_USBHOST,
+		.end   = S3C_PA_USBHOST + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_USBH,
+		.end   = IRQ_USBH,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static u64 s3c_device_usb_dmamask = 0xffffffffUL;
+
+struct platform_device s3c_device_usb = {
+	.name		  = "s3c2410-ohci",
+	.id		  = -1,
+	.num_resources	  = ARRAY_SIZE(s3c_usb_resource),
+	.resource	  = s3c_usb_resource,
+	.dev              = {
+		.dma_mask = &s3c_device_usb_dmamask,
+		.coherent_dma_mask = 0xffffffffUL
+	}
+};
+
+EXPORT_SYMBOL(s3c_device_usb);

arch/arm/plat-s3c/dma.c

+/* linux/arch/arm/plat-s3c/dma.c
+ *
+ * Copyright (c) 2003-2005,2006,2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C DMA core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+struct s3c2410_dma_buf;
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+
+#include <mach/dma.h>
+#include <mach/irqs.h>
+
+#include <plat/dma-plat.h>
+
+/* dma channel state information */
+struct s3c2410_dma_chan s3c2410_chans[S3C_DMA_CHANNELS];
+struct s3c2410_dma_chan *s3c_dma_chan_map[DMACH_MAX];
+
+/* s3c_dma_lookup_channel
+ *
+ * change the dma channel number given into a real dma channel id
+*/
+
+struct s3c2410_dma_chan *s3c_dma_lookup_channel(unsigned int channel)
+{
+	if (channel & DMACH_LOW_LEVEL)
+		return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL];
+	else
+		return s3c_dma_chan_map[channel];
+}
+
+/* do we need to protect the settings of the fields from
+ * irq?
+*/
+
+int s3c2410_dma_set_opfn(unsigned int channel, s3c2410_dma_opfn_t rtn)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: chan=%p, op rtn=%p\n", __func__, chan, rtn);
+
+	chan->op_fn = rtn;
+
+	return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_set_opfn);
+
+int s3c2410_dma_set_buffdone_fn(unsigned int channel, s3c2410_dma_cbfn_t rtn)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: chan=%p, callback rtn=%p\n", __func__, chan, rtn);
+
+	chan->callback_fn = rtn;
+
+	return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
+
+int s3c2410_dma_setflags(unsigned int channel, unsigned int flags)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	chan->flags = flags;
+	return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_setflags);

arch/arm/plat-s3c/gpio.c

@@ -16,7 +16,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 
-#include <plat/gpio-core.h>
+#include <mach/gpio-core.h>
 
 #ifdef CONFIG_S3C_GPIO_TRACK
 struct s3c_gpio_chip *s3c_gpios[S3C_GPIO_END];
@@ -140,6 +140,15 @@ __init void s3c_gpiolib_add(struct s3c_gpio_chip *chip)
 	if (!gc->get)
 		gc->get = s3c_gpiolib_get;
 
+#ifdef CONFIG_PM
+	if (chip->pm != NULL) {
+		if (!chip->pm->save || !chip->pm->resume)
+			printk(KERN_ERR "gpio: %s has missing PM functions\n",
+			       gc->label);
+	} else
+		printk(KERN_ERR "gpio: %s has no PM function\n", gc->label);
+#endif
+
 	/* gpiochip_add() prints own failure message on error. */
 	ret = gpiochip_add(gc);
 	if (ret >= 0)

arch/arm/plat-s3c/include/plat/adc.h

@@ -19,10 +19,12 @@ struct s3c_adc_client;
 extern int s3c_adc_start(struct s3c_adc_client *client,
 			 unsigned int channel, unsigned int nr_samples);
 
-extern struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev,
-					       void (*select)(unsigned selected),
-					       void (*conv)(unsigned d0, unsigned d1),
-					       unsigned int is_ts);
+extern struct s3c_adc_client *
+	s3c_adc_register(struct platform_device *pdev,
+			 void (*select)(unsigned selected),
+			 void (*conv)(unsigned d0, unsigned d1,
+				      unsigned *samples_left),
+			 unsigned int is_ts);
 
 extern void s3c_adc_release(struct s3c_adc_client *client);
 

arch/arm/plat-s3c/include/plat/clock.h

@@ -50,6 +50,7 @@ extern struct clk clk_xtal;
 extern struct clk clk_ext;
 
 /* S3C64XX specific clocks */
+extern struct clk clk_h2;
 extern struct clk clk_27m;
 extern struct clk clk_48m;
 

arch/arm/plat-s3c/include/plat/cpu.h

@@ -69,3 +69,6 @@ extern struct sysdev_class s3c2412_sysclass;
 extern struct sysdev_class s3c2440_sysclass;
 extern struct sysdev_class s3c2442_sysclass;
 extern struct sysdev_class s3c2443_sysclass;
+extern struct sysdev_class s3c6410_sysclass;
+extern struct sysdev_class s3c64xx_sysclass;
+

arch/arm/plat-s3c/include/plat/devs.h

@@ -45,6 +45,7 @@ extern struct platform_device s3c_device_spi1;
 extern struct platform_device s3c_device_nand;
 
 extern struct platform_device s3c_device_usbgadget;
+extern struct platform_device s3c_device_usb_hsotg;
 
 /* s3c2440 specific devices */
 

arch/arm/plat-s3c/include/plat/dma-core.h

+/* arch/arm/plat-s3c/include/plat/dma.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * Samsung S3C DMA core support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+extern struct s3c2410_dma_chan *s3c_dma_lookup_channel(unsigned int channel);
+
+extern struct s3c2410_dma_chan *s3c_dma_chan_map[];
+
+/* the currently allocated channel information */
+extern struct s3c2410_dma_chan s3c2410_chans[];
+
+

arch/arm/plat-s3c/include/plat/dma.h

+/* arch/arm/plat-s3c/include/plat/dma.h
+ *
+ * Copyright (C) 2003,2004,2006 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C DMA support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+enum s3c2410_dma_buffresult {
+	S3C2410_RES_OK,
+	S3C2410_RES_ERR,
+	S3C2410_RES_ABORT
+};
+
+enum s3c2410_dmasrc {
+	S3C2410_DMASRC_HW,		/* source is memory */
+	S3C2410_DMASRC_MEM		/* source is hardware */
+};
+
+/* enum s3c2410_chan_op
+ *
+ * operation codes passed to the DMA code by the user, and also used
+ * to inform the current channel owner of any changes to the system state
+*/
+
+enum s3c2410_chan_op {
+	S3C2410_DMAOP_START,
+	S3C2410_DMAOP_STOP,
+	S3C2410_DMAOP_PAUSE,
+	S3C2410_DMAOP_RESUME,
+	S3C2410_DMAOP_FLUSH,
+	S3C2410_DMAOP_TIMEOUT,		/* internal signal to handler */
+	S3C2410_DMAOP_STARTED,		/* indicate channel started */
+};
+
+struct s3c2410_dma_client {
+	char                *name;
+};
+
+struct s3c2410_dma_chan;
+
+/* s3c2410_dma_cbfn_t
+ *
+ * buffer callback routine type
+*/
+
+typedef void (*s3c2410_dma_cbfn_t)(struct s3c2410_dma_chan *,
+				   void *buf, int size,
+				   enum s3c2410_dma_buffresult result);
+
+typedef int  (*s3c2410_dma_opfn_t)(struct s3c2410_dma_chan *,
+				   enum s3c2410_chan_op );
+
+
+
+/* s3c2410_dma_request
+ *
+ * request a dma channel exclusivley
+*/
+
+extern int s3c2410_dma_request(unsigned int channel,
+			       struct s3c2410_dma_client *, void *dev);
+
+
+/* s3c2410_dma_ctrl
+ *
+ * change the state of the dma channel
+*/
+
+extern int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op);
+
+/* s3c2410_dma_setflags
+ *
+ * set the channel's flags to a given state
+*/
+
+extern int s3c2410_dma_setflags(unsigned int channel,
+				unsigned int flags);
+
+/* s3c2410_dma_free
+ *
+ * free the dma channel (will also abort any outstanding operations)
+*/
+
+extern int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *);
+
+/* s3c2410_dma_enqueue
+ *
+ * place the given buffer onto the queue of operations for the channel.
+ * The buffer must be allocated from dma coherent memory, or the Dcache/WB
+ * drained before the buffer is given to the DMA system.
+*/
+
+extern int s3c2410_dma_enqueue(unsigned int channel, void *id,
+			       dma_addr_t data, int size);
+
+/* s3c2410_dma_config
+ *
+ * configure the dma channel
+*/
+
+extern int s3c2410_dma_config(unsigned int channel, int xferunit);
+
+/* s3c2410_dma_devconfig
+ *
+ * configure the device we're talking to
+*/
+
+extern int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source,
+				 unsigned long devaddr);
+
+/* s3c2410_dma_getposition
+ *
+ * get the position that the dma transfer is currently at
+*/
+
+extern int s3c2410_dma_getposition(unsigned int channel,
+				   dma_addr_t *src, dma_addr_t *dest);
+
+extern int s3c2410_dma_set_opfn(unsigned int, s3c2410_dma_opfn_t rtn);
+extern int s3c2410_dma_set_buffdone_fn(unsigned int, s3c2410_dma_cbfn_t rtn);
+
+

arch/arm/plat-s3c/include/plat/gpio-core.h

@@ -20,6 +20,18 @@
  * specific code.
 */
 
+struct s3c_gpio_chip;
+
+/**
+ * struct s3c_gpio_pm - power management (suspend/resume) information
+ * @save: Routine to save the state of the GPIO block
+ * @resume: Routine to resume the GPIO block.
+ */
+struct s3c_gpio_pm {
+	void (*save)(struct s3c_gpio_chip *chip);
+	void (*resume)(struct s3c_gpio_chip *chip);
+};
+
 struct s3c_gpio_cfg;
 
 /**
@@ -27,6 +39,7 @@ struct s3c_gpio_cfg;
  * @chip: The chip structure to be exported via gpiolib.
  * @base: The base pointer to the gpio configuration registers.
  * @config: special function and pull-resistor control information.
+ * @pm_save: Save information for suspend/resume support.
  *
  * This wrapper provides the necessary information for the Samsung
  * specific gpios being registered with gpiolib.
@@ -34,7 +47,11 @@ struct s3c_gpio_cfg;
 struct s3c_gpio_chip {
 	struct gpio_chip	chip;
 	struct s3c_gpio_cfg	*config;
+	struct s3c_gpio_pm	*pm;
 	void __iomem		*base;
+#ifdef CONFIG_PM
+	u32			pm_save[4];
+#endif
 };
 
 static inline struct s3c_gpio_chip *to_s3c_gpio(struct gpio_chip *gpc)
@@ -75,3 +92,16 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int chip)
 
 static inline void s3c_gpiolib_track(struct s3c_gpio_chip *chip) { }
 #endif
+
+#ifdef CONFIG_PM
+extern struct s3c_gpio_pm s3c_gpio_pm_1bit;
+extern struct s3c_gpio_pm s3c_gpio_pm_2bit;
+extern struct s3c_gpio_pm s3c_gpio_pm_4bit;
+#define __gpio_pm(x) x
+#else
+#define s3c_gpio_pm_1bit NULL
+#define s3c_gpio_pm_2bit NULL
+#define s3c_gpio_pm_4bit NULL
+#define __gpio_pm(x) NULL
+
+#endif /* CONFIG_PM */

arch/arm/plat-s3c/include/plat/pm.h

@@ -44,6 +44,8 @@ extern void (*pm_cpu_sleep)(void);
 
 extern unsigned long s3c_pm_flags;
 
+extern unsigned char pm_uart_udivslot;  /* true to save UART UDIVSLOT */
+
 /* from sleep.S */
 
 extern int  s3c_cpu_save(unsigned long *saveblk);
@@ -88,6 +90,7 @@ struct pm_uart_save {
 	u32	ufcon;
 	u32	umcon;
 	u32	ubrdiv;
+	u32	udivslot;
 };
 
 /* helper functions to save/restore lists of registers. */
@@ -124,6 +127,18 @@ extern void s3c_pm_dbg(const char *msg, ...);
 #define S3C_PMDBG(fmt...) printk(KERN_DEBUG fmt)
 #endif
 
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+/**
+ * s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs
+ * @set: set bits for the state of the LEDs
+ * @clear: clear bits for the state of the LEDs.
+ */
+extern void s3c_pm_debug_smdkled(u32 set, u32 clear);
+
+#else
+static inline void s3c_pm_debug_smdkled(u32 set, u32 clear) { }
+#endif /* CONFIG_S3C_PM_DEBUG_LED_SMDK */
+
 /* suspend memory checking */
 
 #ifdef CONFIG_S3C2410_PM_CHECK

arch/arm/plat-s3c/include/plat/regs-serial.h

@@ -189,6 +189,11 @@
 
 #define S3C2443_DIVSLOT		  (0x2C)
 
+/* S3C64XX interrupt registers. */
+#define S3C64XX_UINTP		0x30
+#define S3C64XX_UINTSP		0x34
+#define S3C64XX_UINTM		0x38
+
 #ifndef __ASSEMBLY__
 
 /* struct s3c24xx_uart_clksrc

arch/arm/plat-s3c/include/plat/sdhci.h

@@ -67,12 +67,52 @@ extern struct s3c_sdhci_platdata s3c_hsmmc1_def_platdata;
 
 /* Helper function availablity */
 
+extern void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
+extern void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
+
+/* S3C6400 SDHCI setup */
+
+#ifdef CONFIG_S3C6400_SETUP_SDHCI
+extern char *s3c6400_hsmmc_clksrcs[4];
+
+#ifdef CONFIG_S3C_DEV_HSMMC
+extern void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev,
+					 void __iomem *r,
+					 struct mmc_ios *ios,
+					 struct mmc_card *card);
+
+static inline void s3c6400_default_sdhci0(void)
+{
+	s3c_hsmmc0_def_platdata.clocks = s3c6400_hsmmc_clksrcs;
+	s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
+	s3c_hsmmc0_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
+}
+
+#else
+static inline void s3c6400_default_sdhci0(void) { }
+#endif  /* CONFIG_S3C_DEV_HSMMC */
+
+#ifdef CONFIG_S3C_DEV_HSMMC1
+static inline void s3c6400_default_sdhci1(void)
+{
+	s3c_hsmmc1_def_platdata.clocks = s3c6400_hsmmc_clksrcs;
+	s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
+	s3c_hsmmc1_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
+}
+#else
+static inline void s3c6400_default_sdhci1(void) { }
+#endif /* CONFIG_S3C_DEV_HSMMC1 */
+
+#else
+static inline void s3c6400_default_sdhci0(void) { }
+static inline void s3c6400_default_sdhci1(void) { }
+#endif /* CONFIG_S3C6400_SETUP_SDHCI */
+
+/* S3C6410 SDHCI setup */
+
 #ifdef CONFIG_S3C6410_SETUP_SDHCI
 extern char *s3c6410_hsmmc_clksrcs[4];
 
-extern void s3c6410_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
-extern void s3c6410_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
-
 extern void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev,
 					   void __iomem *r,
 					   struct mmc_ios *ios,
@@ -82,7 +122,7 @@ extern void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev,
 static inline void s3c6410_default_sdhci0(void)
 {
 	s3c_hsmmc0_def_platdata.clocks = s3c6410_hsmmc_clksrcs;
-	s3c_hsmmc0_def_platdata.cfg_gpio = s3c6410_setup_sdhci0_cfg_gpio;
+	s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
 	s3c_hsmmc0_def_platdata.cfg_card = s3c6410_setup_sdhci0_cfg_card;
 }
 #else
@@ -93,7 +133,7 @@ static inline void s3c6410_default_sdhci0(void) { }
 static inline void s3c6410_default_sdhci1(void)
 {
 	s3c_hsmmc1_def_platdata.clocks = s3c6410_hsmmc_clksrcs;
-	s3c_hsmmc1_def_platdata.cfg_gpio = s3c6410_setup_sdhci1_cfg_gpio;
+	s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
 	s3c_hsmmc1_def_platdata.cfg_card = s3c6410_setup_sdhci0_cfg_card;
 }
 #else

arch/arm/plat-s3c/include/plat/udc-hs.h

+/* arch/arm/plat-s3c/include/plat/udc-hs.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *      Ben Dooks <ben@simtec.co.uk>
+ *      http://armlinux.simtec.co.uk/
+ *
+ * S3C USB2.0 High-speed / OtG platform information
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+enum s3c_hostg_dmamode {
+	S3C_HSOTG_DMA_NONE,	/* do not use DMA at-all */
+	S3C_HSOTG_DMA_ONLY,	/* always use DMA */
+	S3C_HSOTG_DMA_DRV,	/* DMA is chosen by driver */
+};
+
+/**
+ * struct s3c_hsotg_plat - platform data for high-speed otg/udc
+ * @dma: Whether to use DMA or not.
+ * @is_osc: The clock source is an oscillator, not a crystal
+ */
+struct s3c_hsotg_plat {
+	enum s3c_hostg_dmamode	dma;
+	unsigned int		is_osc : 1;
+};

arch/arm/plat-s3c/include/plat/watchdog-reset.h

+/* arch/arm/plat-s3c/include/plat/watchdog-reset.h
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - System define for arch_reset() function
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <plat/regs-watchdog.h>
+#include <mach/map.h>
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+static inline void arch_wdt_reset(void)
+{
+	struct clk *wdtclk;
+
+	printk("arch_reset: attempting watchdog reset\n");
+
+	__raw_writel(0, S3C2410_WTCON);	  /* disable watchdog, to be safe  */
+
+	wdtclk = clk_get(NULL, "watchdog");
+	if (!IS_ERR(wdtclk)) {
+		clk_enable(wdtclk);
+	} else
+		printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__);
+
+	/* put initial values into count and data */
+	__raw_writel(0x80, S3C2410_WTCNT);
+	__raw_writel(0x80, S3C2410_WTDAT);
+
+	/* set the watchdog to go and reset... */
+	__raw_writel(S3C2410_WTCON_ENABLE|S3C2410_WTCON_DIV16|S3C2410_WTCON_RSTEN |
+		     S3C2410_WTCON_PRESCALE(0x20), S3C2410_WTCON);
+
+	/* wait for reset to assert... */
+	mdelay(500);
+
+	printk(KERN_ERR "Watchdog reset failed to assert reset\n");
+
+	/* delay to allow the serial port to show the message */
+	mdelay(50);
+}

arch/arm/plat-s3c/pm-gpio.c

+
+/* linux/arch/arm/plat-s3c/pm-gpio.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C series GPIO PM code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/sysdev.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <mach/gpio-core.h>
+#include <plat/pm.h>
+
+/* PM GPIO helpers */
+
+#define OFFS_CON	(0x00)
+#define OFFS_DAT	(0x04)
+#define OFFS_UP		(0x08)
+
+static void s3c_gpio_pm_1bit_save(struct s3c_gpio_chip *chip)
+{
+	chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
+	chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
+}
+
+static void s3c_gpio_pm_1bit_resume(struct s3c_gpio_chip *chip)
+{
+	void __iomem *base = chip->base;
+	u32 old_gpcon = __raw_readl(base + OFFS_CON);
+	u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+	u32 gps_gpcon = chip->pm_save[0];
+	u32 gps_gpdat = chip->pm_save[1];
+	u32 gpcon;
+
+	/* GPACON only has one bit per control / data and no PULLUPs.
+	 * GPACON[x] = 0 => Output, 1 => SFN */
+
+	/* first set all SFN bits to SFN */
+
+	gpcon = old_gpcon | gps_gpcon;
+	__raw_writel(gpcon, base + OFFS_CON);
+
+	/* now set all the other bits */
+
+	__raw_writel(gps_gpdat, base + OFFS_DAT);
+	__raw_writel(gps_gpcon, base + OFFS_CON);
+
+	S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n",
+		  chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
+}
+
+struct s3c_gpio_pm s3c_gpio_pm_1bit = {
+	.save	= s3c_gpio_pm_1bit_save,
+	.resume = s3c_gpio_pm_1bit_resume,
+};
+
+static void s3c_gpio_pm_2bit_save(struct s3c_gpio_chip *chip)
+{
+	chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
+	chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
+	chip->pm_save[2] = __raw_readl(chip->base + OFFS_UP);
+}
+
+/* Test whether the given masked+shifted bits of an GPIO configuration
+ * are one of the SFN (special function) modes. */
+
+static inline int is_sfn(unsigned long con)
+{
+	return con >= 2;
+}
+
+/* Test if the given masked+shifted GPIO configuration is an input */
+
+static inline int is_in(unsigned long con)
+{
+	return con == 0;
+}
+
+/* Test if the given masked+shifted GPIO configuration is an output */
+
+static inline int is_out(unsigned long con)
+{
+	return con == 1;
+}
+
+/**
+ * s3c_gpio_pm_2bit_resume() - restore the given GPIO bank
+ * @chip: The chip information to resume.
+ *
+ * Restore one of the GPIO banks that was saved during suspend. This is
+ * not as simple as once thought, due to the possibility of glitches
+ * from the order that the CON and DAT registers are set in.
+ *
+ * The three states the pin can be are {IN,OUT,SFN} which gives us 9
+ * combinations of changes to check. Three of these, if the pin stays
+ * in the same configuration can be discounted. This leaves us with
+ * the following:
+ *
+ * { IN => OUT }  Change DAT first
+ * { IN => SFN }  Change CON first
+ * { OUT => SFN } Change CON first, so new data will not glitch
+ * { OUT => IN }  Change CON first, so new data will not glitch
+ * { SFN => IN }  Change CON first
+ * { SFN => OUT } Change DAT first, so new data will not glitch [1]
+ *
+ * We do not currently deal with the UP registers as these control
+ * weak resistors, so a small delay in change should not need to bring
+ * these into the calculations.
+ *
+ * [1] this assumes that writing to a pin DAT whilst in SFN will set the
+ *     state for when it is next output.
+ */
+static void s3c_gpio_pm_2bit_resume(struct s3c_gpio_chip *chip)
+{
+	void __iomem *base = chip->base;
+	u32 old_gpcon = __raw_readl(base + OFFS_CON);
+	u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+	u32 gps_gpcon = chip->pm_save[0];
+	u32 gps_gpdat = chip->pm_save[1];
+	u32 gpcon, old, new, mask;
+	u32 change_mask = 0x0;
+	int nr;
+
+	/* restore GPIO pull-up settings */
+	__raw_writel(chip->pm_save[2], base + OFFS_UP);
+
+	/* Create a change_mask of all the items that need to have
+	 * their CON value changed before their DAT value, so that
+	 * we minimise the work between the two settings.
+	 */
+
+	for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) {
+		old = (old_gpcon & mask) >> nr;
+		new = (gps_gpcon & mask) >> nr;
+
+		/* If there is no change, then skip */
+
+		if (old == new)
+			continue;
+
+		/* If both are special function, then skip */
+
+		if (is_sfn(old) && is_sfn(new))
+			continue;
+
+		/* Change is IN => OUT, do not change now */
+
+		if (is_in(old) && is_out(new))
+			continue;
+
+		/* Change is SFN => OUT, do not change now */
+
+		if (is_sfn(old) && is_out(new))
+			continue;
+
+		/* We should now be at the case of IN=>SFN,
+		 * OUT=>SFN, OUT=>IN, SFN=>IN. */
+
+		change_mask |= mask;
+	}
+
+
+	/* Write the new CON settings */
+
+	gpcon = old_gpcon & ~change_mask;
+	gpcon |= gps_gpcon & change_mask;
+
+	__raw_writel(gpcon, base + OFFS_CON);
+
+	/* Now change any items that require DAT,CON */
+
+	__raw_writel(gps_gpdat, base + OFFS_DAT);
+	__raw_writel(gps_gpcon, base + OFFS_CON);
+
+	S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n",
+		  chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
+}
+
+struct s3c_gpio_pm s3c_gpio_pm_2bit = {
+	.save	= s3c_gpio_pm_2bit_save,
+	.resume = s3c_gpio_pm_2bit_resume,
+};
+
+#ifdef CONFIG_ARCH_S3C64XX
+static void s3c_gpio_pm_4bit_save(struct s3c_gpio_chip *chip)
+{
+	chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON);
+	chip->pm_save[2] = __raw_readl(chip->base + OFFS_DAT);
+	chip->pm_save[3] = __raw_readl(chip->base + OFFS_UP);
+
+	if (chip->chip.ngpio > 8)
+		chip->pm_save[0] = __raw_readl(chip->base - 4);
+}
+
+static u32 s3c_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon)
+{
+	u32 old, new, mask;
+	u32 change_mask = 0x0;
+	int nr;
+
+	for (nr = 0, mask = 0x0f; nr < 16; nr += 4, mask <<= 4) {
+		old = (old_gpcon & mask) >> nr;
+		new = (gps_gpcon & mask) >> nr;
+
+		/* If there is no change, then skip */
+
+		if (old == new)
+			continue;
+
+		/* If both are special function, then skip */
+
+		if (is_sfn(old) && is_sfn(new))
+			continue;
+
+		/* Change is IN => OUT, do not change now */
+
+		if (is_in(old) && is_out(new))
+			continue;
+
+		/* Change is SFN => OUT, do not change now */
+
+		if (is_sfn(old) && is_out(new))
+			continue;
+
+		/* We should now be at the case of IN=>SFN,
+		 * OUT=>SFN, OUT=>IN, SFN=>IN. */
+
+		change_mask |= mask;
+	}
+
+	return change_mask;
+}
+
+static void s3c_gpio_pm_4bit_con(struct s3c_gpio_chip *chip, int index)
+{
+	void __iomem *con = chip->base + (index * 4);
+	u32 old_gpcon = __raw_readl(con);
+	u32 gps_gpcon = chip->pm_save[index + 1];
+	u32 gpcon, mask;
+
+	mask = s3c_gpio_pm_4bit_mask(old_gpcon, gps_gpcon);
+
+	gpcon = old_gpcon & ~mask;
+	gpcon |= gps_gpcon & mask;
+
+	__raw_writel(gpcon, con);
+}
+
+static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip)
+{
+	void __iomem *base = chip->base;
+	u32 old_gpcon[2];
+	u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+	u32 gps_gpdat = chip->pm_save[2];
+
+	/* First, modify the CON settings */
+
+	old_gpcon[0] = 0;
+	old_gpcon[1] = __raw_readl(base + OFFS_CON);
+
+	s3c_gpio_pm_4bit_con(chip, 0);
+	if (chip->chip.ngpio > 8) {
+		old_gpcon[0] = __raw_readl(base - 4);
+		s3c_gpio_pm_4bit_con(chip, -1);
+	}
+
+	/* Now change the configurations that require DAT,CON */
+
+	__raw_writel(chip->pm_save[2], base + OFFS_DAT);
+	__raw_writel(chip->pm_save[1], base + OFFS_CON);
+	if (chip->chip.ngpio > 8)
+		__raw_writel(chip->pm_save[0], base - 4);
+
+	__raw_writel(chip->pm_save[2], base + OFFS_DAT);
+	__raw_writel(chip->pm_save[3], base + OFFS_UP);
+
+	if (chip->chip.ngpio > 8) {
+		S3C_PMDBG("%s: CON4 %08x,%08x => %08x,%08x, DAT %08x => %08x\n",
+			  chip->chip.label, old_gpcon[0], old_gpcon[1],
+			  __raw_readl(base - 4),
+			  __raw_readl(base + OFFS_CON),
+			  old_gpdat, gps_gpdat);
+	} else
+		S3C_PMDBG("%s: CON4 %08x => %08x, DAT %08x => %08x\n",
+			  chip->chip.label, old_gpcon[1],
+			  __raw_readl(base + OFFS_CON),
+			  old_gpdat, gps_gpdat);
+}
+
+struct s3c_gpio_pm s3c_gpio_pm_4bit = {
+	.save	= s3c_gpio_pm_4bit_save,
+	.resume = s3c_gpio_pm_4bit_resume,
+};
+#endif /* CONFIG_ARCH_S3C64XX */
+
+/**
+ * s3c_pm_save_gpio() - save gpio chip data for suspend
+ * @ourchip: The chip for suspend.
+ */
+static void s3c_pm_save_gpio(struct s3c_gpio_chip *ourchip)
+{
+	struct s3c_gpio_pm *pm = ourchip->pm;
+
+	if (pm == NULL || pm->save == NULL)
+		S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
+	else
+		pm->save(ourchip);
+}
+
+/**
+ * s3c_pm_save_gpios() - Save the state of the GPIO banks.
+ *
+ * For all the GPIO banks, save the state of each one ready for going
+ * into a suspend mode.
+ */
+void s3c_pm_save_gpios(void)
+{
+	struct s3c_gpio_chip *ourchip;
+	unsigned int gpio_nr;
+
+	for (gpio_nr = 0; gpio_nr < S3C_GPIO_END; gpio_nr++) {
+		ourchip = s3c_gpiolib_getchip(gpio_nr);
+		if (!ourchip)
+			continue;
+
+		s3c_pm_save_gpio(ourchip);
+
+		S3C_PMDBG("%s: save %08x,%08x,%08x,%08x\n",
+			  ourchip->chip.label,
+			  ourchip->pm_save[0],
+			  ourchip->pm_save[1],
+			  ourchip->pm_save[2],
+			  ourchip->pm_save[3]);
+
+		gpio_nr += ourchip->chip.ngpio;
+		gpio_nr += CONFIG_S3C_GPIO_SPACE;
+	}
+}
+
+/**
+ * s3c_pm_resume_gpio() - restore gpio chip data after suspend
+ * @ourchip: The suspended chip.
+ */
+static void s3c_pm_resume_gpio(struct s3c_gpio_chip *ourchip)
+{
+	struct s3c_gpio_pm *pm = ourchip->pm;
+
+	if (pm == NULL || pm->resume == NULL)
+		S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
+	else
+		pm->resume(ourchip);
+}
+
+void s3c_pm_restore_gpios(void)
+{
+	struct s3c_gpio_chip *ourchip;
+	unsigned int gpio_nr;
+
+	for (gpio_nr = 0; gpio_nr < S3C_GPIO_END; gpio_nr++) {
+		ourchip = s3c_gpiolib_getchip(gpio_nr);
+		if (!ourchip)
+			continue;
+
+		s3c_pm_resume_gpio(ourchip);
+
+		gpio_nr += ourchip->chip.ngpio;
+		gpio_nr += CONFIG_S3C_GPIO_SPACE;
+	}
+}

arch/arm/plat-s3c/pm.c

@@ -21,11 +21,10 @@
 
 #include <asm/cacheflush.h>
 #include <mach/hardware.h>
+#include <mach/map.h>
 
 #include <plat/regs-serial.h>
 #include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-mem.h>
 #include <mach/regs-irq.h>
 #include <asm/irq.h>
 
@@ -70,6 +69,8 @@ static inline void s3c_pm_debug_init(void)
 
 /* Save the UART configurations if we are configured for debug. */
 
+unsigned char pm_uart_udivslot;
+
 #ifdef CONFIG_S3C2410_PM_DEBUG
 
 struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS];
@@ -83,6 +84,12 @@ static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save)
 	save->ufcon = __raw_readl(regs + S3C2410_UFCON);
 	save->umcon = __raw_readl(regs + S3C2410_UMCON);
 	save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
+
+	if (pm_uart_udivslot)
+		save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
+
+	S3C_PMDBG("UART[%d]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
+		  uart, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
 }
 
 static void s3c_pm_save_uarts(void)
@@ -98,11 +105,16 @@ static void s3c_pm_restore_uart(unsigned int uart, struct pm_uart_save *save)
 {
 	void __iomem *regs = S3C_VA_UARTx(uart);
 
+	s3c_pm_arch_update_uart(regs, save);
+
 	__raw_writel(save->ulcon, regs + S3C2410_ULCON);
 	__raw_writel(save->ucon,  regs + S3C2410_UCON);
 	__raw_writel(save->ufcon, regs + S3C2410_UFCON);
 	__raw_writel(save->umcon, regs + S3C2410_UMCON);
 	__raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
+
+	if (pm_uart_udivslot)
+		__raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
 }
 
 static void s3c_pm_restore_uarts(void)
@@ -313,6 +325,9 @@ static int s3c_pm_enter(suspend_state_t state)
 
 	S3C_PMDBG("%s: post sleep, preparing to return\n", __func__);
 
+	/* LEDs should now be 1110 */
+	s3c_pm_debug_smdkled(1 << 1, 0);
+
 	s3c_pm_check_restore();
 
 	/* ok, let's return from sleep */

arch/arm/plat-s3c24xx/Kconfig

@@ -71,6 +71,7 @@ config PM_SIMTEC
 config S3C2410_DMA
 	bool "S3C2410 DMA support"
 	depends on ARCH_S3C2410
+	select S3C_DMA
 	help
 	  S3C2410 DMA support. This is needed for drivers like sound which
 	  use the S3C2410's DMA system to move data to and from the

arch/arm/plat-s3c24xx/adc.c

@@ -45,7 +45,8 @@ struct s3c_adc_client {
 	unsigned char		 channel;
 
 	void	(*select_cb)(unsigned selected);
-	void	(*convert_cb)(unsigned val1, unsigned val2);
+	void	(*convert_cb)(unsigned val1, unsigned val2,
+			      unsigned *samples_left);
 };
 
 struct adc_device {
@@ -158,7 +159,8 @@ static void s3c_adc_default_select(unsigned select)
 
 struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev,
 					void (*select)(unsigned int selected),
-					void (*conv)(unsigned d0, unsigned d1),
+					void (*conv)(unsigned d0, unsigned d1,
+						     unsigned *samples_left),
 					unsigned int is_ts)
 {
 	struct s3c_adc_client *client;
@@ -227,9 +229,10 @@ static irqreturn_t s3c_adc_irq(int irq, void *pw)
 	data1 = readl(adc->regs + S3C2410_ADCDAT1);
 	adc_dbg(adc, "read %d: 0x%04x, 0x%04x\n", client->nr_samples, data0, data1);
 
-	(client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff);
+	client->nr_samples--;
+	(client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff, &client->nr_samples);
 
-	if (--client->nr_samples > 0) {
+	if (client->nr_samples > 0) {
 		/* fire another conversion for this */
 
 		client->select_cb(1);

arch/arm/plat-s3c24xx/common-smdk.c

@@ -18,6 +18,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/sysdev.h>
 #include <linux/platform_device.h>
 
@@ -47,27 +48,27 @@
 /* LED devices */
 
 static struct s3c24xx_led_platdata smdk_pdata_led4 = {
-	.gpio		= S3C2410_GPF4,
+	.gpio		= S3C2410_GPF(4),
 	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
 	.name		= "led4",
 	.def_trigger	= "timer",
 };
 
 static struct s3c24xx_led_platdata smdk_pdata_led5 = {
-	.gpio		= S3C2410_GPF5,
+	.gpio		= S3C2410_GPF(5),
 	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
 	.name		= "led5",
 	.def_trigger	= "nand-disk",
 };
 
 static struct s3c24xx_led_platdata smdk_pdata_led6 = {
-	.gpio		= S3C2410_GPF6,
+	.gpio		= S3C2410_GPF(6),
 	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
 	.name		= "led6",
 };
 
 static struct s3c24xx_led_platdata smdk_pdata_led7 = {
-	.gpio		= S3C2410_GPF7,
+	.gpio		= S3C2410_GPF(7),
 	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
 	.name		= "led7",
 };
@@ -184,15 +185,15 @@ void __init smdk_machine_init(void)
 {
 	/* Configure the LEDs (even if we have no LED support)*/
 
-	s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP);
-	s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP);
-	s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP);
-	s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT);
 
-	s3c2410_gpio_setpin(S3C2410_GPF4, 1);
-	s3c2410_gpio_setpin(S3C2410_GPF5, 1);
-	s3c2410_gpio_setpin(S3C2410_GPF6, 1);
-	s3c2410_gpio_setpin(S3C2410_GPF7, 1);
+	s3c2410_gpio_setpin(S3C2410_GPF(4), 1);
+	s3c2410_gpio_setpin(S3C2410_GPF(5), 1);
+	s3c2410_gpio_setpin(S3C2410_GPF(6), 1);
+	s3c2410_gpio_setpin(S3C2410_GPF(7), 1);
 
 	if (machine_is_smdk2443())
 		smdk_nand_info.twrph0 = 50;

arch/arm/plat-s3c24xx/devs.c

@@ -136,36 +136,6 @@ struct platform_device *s3c24xx_uart_src[4] = {
 struct platform_device *s3c24xx_uart_devs[4] = {
 };
 
-/* USB Host Controller */
-
-static struct resource s3c_usb_resource[] = {
-	[0] = {
-		.start = S3C24XX_PA_USBHOST,
-		.end   = S3C24XX_PA_USBHOST + S3C24XX_SZ_USBHOST - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_USBH,
-		.end   = IRQ_USBH,
-		.flags = IORESOURCE_IRQ,
-	}
-};
-
-static u64 s3c_device_usb_dmamask = 0xffffffffUL;
-
-struct platform_device s3c_device_usb = {
-	.name		  = "s3c2410-ohci",
-	.id		  = -1,
-	.num_resources	  = ARRAY_SIZE(s3c_usb_resource),
-	.resource	  = s3c_usb_resource,
-	.dev              = {
-		.dma_mask = &s3c_device_usb_dmamask,
-		.coherent_dma_mask = 0xffffffffUL
-	}
-};
-
-EXPORT_SYMBOL(s3c_device_usb);
-
 /* LCD Controller */
 
 static struct resource s3c_lcd_resource[] = {

arch/arm/plat-s3c24xx/dma.c

@@ -31,10 +31,10 @@
 #include <asm/irq.h>
 #include <mach/hardware.h>
 #include <mach/dma.h>
-
 #include <mach/map.h>
 
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
+#include <plat/regs-dma.h>
 
 /* io map for dma */
 static void __iomem *dma_base;
@@ -44,8 +44,6 @@ static int dma_channels;
 
 static struct s3c24xx_dma_selection dma_sel;
 
-/* dma channel state information */
-struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
 
 /* debugging functions */
 
@@ -135,21 +133,6 @@ dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan)
 #define dbg_showchan(chan) do { } while(0)
 #endif /* CONFIG_S3C2410_DMA_DEBUG */
 
-static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX];
-
-/* lookup_dma_channel
- *
- * change the dma channel number given into a real dma channel id
-*/
-
-static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel)
-{
-	if (channel & DMACH_LOW_LEVEL)
-		return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL];
-	else
-		return dma_chan_map[channel];
-}
-
 /* s3c2410_dma_stats_timeout
  *
  * Update DMA stats from timeout info
@@ -214,8 +197,6 @@ s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line)
 	return 0;
 }
 
-
-
 /* s3c2410_dma_loadbuffer
  *
  * load a buffer, and update the channel state
@@ -453,7 +434,7 @@ s3c2410_dma_canload(struct s3c2410_dma_chan *chan)
 int s3c2410_dma_enqueue(unsigned int channel, void *id,
 			dma_addr_t data, int size)
 {
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
 	struct s3c2410_dma_buf *buf;
 	unsigned long flags;
 
@@ -804,7 +785,7 @@ EXPORT_SYMBOL(s3c2410_dma_request);
 
 int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client)
 {
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
 	unsigned long flags;
 
 	if (chan == NULL)
@@ -836,7 +817,7 @@ int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client)
 	chan->irq_claimed = 0;
 
 	if (!(channel & DMACH_LOW_LEVEL))
-		dma_chan_map[channel] = NULL;
+		s3c_dma_chan_map[channel] = NULL;
 
 	local_irq_restore(flags);
 
@@ -995,7 +976,7 @@ static int s3c2410_dma_started(struct s3c2410_dma_chan *chan)
 int
 s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op)
 {
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
 
 	if (chan == NULL)
 		return -EINVAL;
@@ -1038,14 +1019,13 @@ EXPORT_SYMBOL(s3c2410_dma_ctrl);
 /* s3c2410_dma_config
  *
  * xfersize:     size of unit in bytes (1,2,4)
- * dcon:         base value of the DCONx register
 */
 
 int s3c2410_dma_config(unsigned int channel,
-		       int xferunit,
-		       int dcon)
+		       int xferunit)
 {
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+	unsigned int dcon;
 
 	pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n",
 		 __func__, channel, xferunit, dcon);
@@ -1055,10 +1035,33 @@ int s3c2410_dma_config(unsigned int channel,
 
 	pr_debug("%s: Initial dcon is %08x\n", __func__, dcon);
 
-	dcon |= chan->dcon & dma_sel.dcon_mask;
+	dcon = chan->dcon & dma_sel.dcon_mask;
 
 	pr_debug("%s: New dcon is %08x\n", __func__, dcon);
 
+	switch (chan->req_ch) {
+	case DMACH_I2S_IN:
+	case DMACH_I2S_OUT:
+	case DMACH_PCM_IN:
+	case DMACH_PCM_OUT:
+	case DMACH_MIC_IN:
+	default:
+		dcon |= S3C2410_DCON_HANDSHAKE;
+		dcon |= S3C2410_DCON_SYNC_PCLK;
+		break;
+
+	case DMACH_SDI:
+		/* note, ensure if need HANDSHAKE or not */
+		dcon |= S3C2410_DCON_SYNC_PCLK;
+		break;
+
+	case DMACH_XD0:
+	case DMACH_XD1:
+		dcon |= S3C2410_DCON_HANDSHAKE;
+		dcon |= S3C2410_DCON_SYNC_HCLK;
+		break;
+	}
+
 	switch (xferunit) {
 	case 1:
 		dcon |= S3C2410_DCON_BYTE;
@@ -1090,58 +1093,6 @@ int s3c2410_dma_config(unsigned int channel,
 
 EXPORT_SYMBOL(s3c2410_dma_config);
 
-int s3c2410_dma_setflags(unsigned int channel, unsigned int flags)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: chan=%p, flags=%08x\n", __func__, chan, flags);
-
-	chan->flags = flags;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_setflags);
-
-
-/* do we need to protect the settings of the fields from
- * irq?
-*/
-
-int s3c2410_dma_set_opfn(unsigned int channel, s3c2410_dma_opfn_t rtn)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: chan=%p, op rtn=%p\n", __func__, chan, rtn);
-
-	chan->op_fn = rtn;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_set_opfn);
-
-int s3c2410_dma_set_buffdone_fn(unsigned int channel, s3c2410_dma_cbfn_t rtn)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: chan=%p, callback rtn=%p\n", __func__, chan, rtn);
-
-	chan->callback_fn = rtn;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
 
 /* s3c2410_dma_devconfig
  *
@@ -1150,29 +1101,38 @@ EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
  * source:    S3C2410_DMASRC_HW: source is hardware
  *            S3C2410_DMASRC_MEM: source is memory
  *
- * hwcfg:     the value for xxxSTCn register,
- *            bit 0: 0=increment pointer, 1=leave pointer
- *            bit 1: 0=source is AHB, 1=source is APB
- *
  * devaddr:   physical address of the source
 */
 
 int s3c2410_dma_devconfig(int channel,
 			  enum s3c2410_dmasrc source,
-			  int hwcfg,
 			  unsigned long devaddr)
 {
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+	unsigned int hwcfg;
 
 	if (chan == NULL)
 		return -EINVAL;
 
-	pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n",
-		 __func__, (int)source, hwcfg, devaddr);
+	pr_debug("%s: source=%d, devaddr=%08lx\n",
+		 __func__, (int)source, devaddr);
 
 	chan->source = source;
 	chan->dev_addr = devaddr;
-	chan->hw_cfg = hwcfg;
+
+	switch (chan->req_ch) {
+	case DMACH_XD0:
+	case DMACH_XD1:
+		hwcfg = 0; /* AHB */
+		break;
+
+	default:
+		hwcfg = S3C2410_DISRCC_APB;
+	}
+
+	/* always assume our peripheral desintation is a fixed
+	 * address in memory. */
+	 hwcfg |= S3C2410_DISRCC_INC;
 
 	switch (source) {
 	case S3C2410_DMASRC_HW:
@@ -1219,7 +1179,7 @@ EXPORT_SYMBOL(s3c2410_dma_devconfig);
 
 int s3c2410_dma_getposition(unsigned int channel, dma_addr_t *src, dma_addr_t *dst)
 {
- 	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
 
 	if (chan == NULL)
 		return -EINVAL;
@@ -1278,8 +1238,8 @@ static int s3c2410_dma_resume(struct sys_device *dev)
 
 	printk(KERN_INFO "dma%d: restoring configuration\n", cp->number);
 
-	s3c2410_dma_config(no, cp->xfer_unit, cp->dcon);
-	s3c2410_dma_devconfig(no, cp->source, cp->hw_cfg, cp->dev_addr);
+	s3c2410_dma_config(no, cp->xfer_unit);
+	s3c2410_dma_devconfig(no, cp->source, cp->dev_addr);
 
 	/* re-select the dma source for this channel */
 
@@ -1476,7 +1436,8 @@ static struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel)
  found:
 	dmach = &s3c2410_chans[ch];
 	dmach->map = ch_map;
-	dma_chan_map[channel] = dmach;
+	dmach->req_ch = channel;
+	s3c_dma_chan_map[channel] = dmach;
 
 	/* select the channel */
 

arch/arm/plat-s3c24xx/gpio.c

@@ -183,35 +183,19 @@ EXPORT_SYMBOL(s3c2410_modify_misccr);
 
 int s3c2410_gpio_getirq(unsigned int pin)
 {
-	if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15)
-		return -1;	/* not valid interrupts */
+	if (pin < S3C2410_GPF(0) || pin > S3C2410_GPG(15))
+		return -EINVAL;	/* not valid interrupts */
 
-	if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7)
-		return -1;	/* not valid pin */
+	if (pin < S3C2410_GPG(0) && pin > S3C2410_GPF(7))
+		return -EINVAL;	/* not valid pin */
 
-	if (pin < S3C2410_GPF4)
-		return (pin - S3C2410_GPF0) + IRQ_EINT0;
+	if (pin < S3C2410_GPF(4))
+		return (pin - S3C2410_GPF(0)) + IRQ_EINT0;
 
-	if (pin < S3C2410_GPG0)
-		return (pin - S3C2410_GPF4) + IRQ_EINT4;
+	if (pin < S3C2410_GPG(0))
+		return (pin - S3C2410_GPF(4)) + IRQ_EINT4;
 
-	return (pin - S3C2410_GPG0) + IRQ_EINT8;
+	return (pin - S3C2410_GPG(0)) + IRQ_EINT8;
 }
 
 EXPORT_SYMBOL(s3c2410_gpio_getirq);
-
-int s3c2410_gpio_irq2pin(unsigned int irq)
-{
-	if (irq >= IRQ_EINT0 && irq <= IRQ_EINT3)
-		return S3C2410_GPF0 + (irq - IRQ_EINT0);
-
-	if (irq >= IRQ_EINT4 && irq <= IRQ_EINT7)
-		return S3C2410_GPF4 + (irq - IRQ_EINT4);
-
-	if (irq >= IRQ_EINT8 && irq <= IRQ_EINT23)
-		return S3C2410_GPG0 + (irq - IRQ_EINT8);
-
-	return -EINVAL;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_irq2pin);

arch/arm/plat-s3c24xx/gpiolib.c

@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
+#include <linux/sysdev.h>
 #include <linux/ioport.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
@@ -22,6 +23,7 @@
 #include <mach/gpio-core.h>
 #include <mach/hardware.h>
 #include <asm/irq.h>
+#include <plat/pm.h>
 
 #include <mach/regs-gpio.h>
 
@@ -77,9 +79,10 @@ static int s3c24xx_gpiolib_bankg_toirq(struct gpio_chip *chip, unsigned offset)
 
 struct s3c_gpio_chip s3c24xx_gpios[] = {
 	[0] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPA0),
+		.base	= S3C2410_GPACON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_1bit),
 		.chip	= {
-			.base			= S3C2410_GPA0,
+			.base			= S3C2410_GPA(0),
 			.owner			= THIS_MODULE,
 			.label			= "GPIOA",
 			.ngpio			= 24,
@@ -88,45 +91,50 @@ struct s3c_gpio_chip s3c24xx_gpios[] = {
 		},
 	},
 	[1] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPB0),
+		.base	= S3C2410_GPBCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
 		.chip	= {
-			.base			= S3C2410_GPB0,
+			.base			= S3C2410_GPB(0),
 			.owner			= THIS_MODULE,
 			.label			= "GPIOB",
 			.ngpio			= 16,
 		},
 	},
 	[2] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPC0),
+		.base	= S3C2410_GPCCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
 		.chip	= {
-			.base			= S3C2410_GPC0,
+			.base			= S3C2410_GPC(0),
 			.owner			= THIS_MODULE,
 			.label			= "GPIOC",
 			.ngpio			= 16,
 		},
 	},
 	[3] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPD0),
+		.base	= S3C2410_GPDCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
 		.chip	= {
-			.base			= S3C2410_GPD0,
+			.base			= S3C2410_GPD(0),
 			.owner			= THIS_MODULE,
 			.label			= "GPIOD",
 			.ngpio			= 16,
 		},
 	},
 	[4] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPE0),
+		.base	= S3C2410_GPECON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
 		.chip	= {
-			.base			= S3C2410_GPE0,
+			.base			= S3C2410_GPE(0),
 			.label			= "GPIOE",
 			.owner			= THIS_MODULE,
 			.ngpio			= 16,
 		},
 	},
 	[5] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPF0),
+		.base	= S3C2410_GPFCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
 		.chip	= {
-			.base			= S3C2410_GPF0,
+			.base			= S3C2410_GPF(0),
 			.owner			= THIS_MODULE,
 			.label			= "GPIOF",
 			.ngpio			= 8,
@@ -134,14 +142,24 @@ struct s3c_gpio_chip s3c24xx_gpios[] = {
 		},
 	},
 	[6] = {
-		.base	= S3C24XX_GPIO_BASE(S3C2410_GPG0),
+		.base	= S3C2410_GPGCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
 		.chip	= {
-			.base			= S3C2410_GPG0,
+			.base			= S3C2410_GPG(0),
 			.owner			= THIS_MODULE,
 			.label			= "GPIOG",
-			.ngpio			= 10,
+			.ngpio			= 16,
 			.to_irq			= s3c24xx_gpiolib_bankg_toirq,
 		},
+	}, {
+		.base	= S3C2410_GPHCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
+		.chip	= {
+			.base			= S3C2410_GPH(0),
+			.owner			= THIS_MODULE,
+			.label			= "GPIOH",
+			.ngpio			= 11,
+		},
 	},
 };
 
@@ -156,4 +174,4 @@ static __init int s3c24xx_gpiolib_init(void)
 	return 0;
 }
 
-arch_initcall(s3c24xx_gpiolib_init);
+core_initcall(s3c24xx_gpiolib_init);

arch/arm/plat-s3c24xx/include/plat/dma.h → arch/arm/plat-s3c24xx/include/plat/dma-plat.h

-/* linux/include/asm-arm/plat-s3c24xx/dma.h
+/* linux/arch/arm/plat-s3c24xx/include/plat/dma-plat.h
  *
  * Copyright (C) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -10,8 +10,10 @@
  * published by the Free Software Foundation.
 */
 
+#include <plat/dma-core.h>
+
 extern struct sysdev_class dma_sysclass;
-extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
+extern struct s3c2410_dma_chan s3c2410_chans[S3C_DMA_CHANNELS];
 
 #define DMA_CH_VALID		(1<<31)
 #define DMA_CH_NEVER		(1<<30)
@@ -31,8 +33,8 @@ struct s3c24xx_dma_map {
 	const char		*name;
 	struct s3c24xx_dma_addr  hw_addr;
 
-	unsigned long		 channels[S3C2410_DMA_CHANNELS];
-	unsigned long		 channels_rx[S3C2410_DMA_CHANNELS];
+	unsigned long		 channels[S3C_DMA_CHANNELS];
+	unsigned long		 channels_rx[S3C_DMA_CHANNELS];
 };
 
 struct s3c24xx_dma_selection {
@@ -58,7 +60,7 @@ extern int s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel);
 */
 
 struct s3c24xx_dma_order_ch {
-	unsigned int	list[S3C2410_DMA_CHANNELS];	/* list of channels */
+	unsigned int	list[S3C_DMA_CHANNELS];	/* list of channels */
 	unsigned int	flags;				/* flags */
 };
 

arch/arm/plat-s3c24xx/include/plat/map.h

@@ -58,7 +58,6 @@
 #define S3C24XX_SZ_SPI		SZ_1M
 #define S3C24XX_SZ_SDI		SZ_1M
 #define S3C24XX_SZ_NAND		SZ_1M
-#define S3C24XX_SZ_USBHOST	SZ_1M
 
 /* GPIO ports */
 

arch/arm/plat-s3c24xx/include/plat/pm-core.h

@@ -57,3 +57,8 @@ static inline void s3c_pm_arch_show_resume_irqs(void)
 	s3c_pm_show_resume_irqs(IRQ_EINT4-4, __raw_readl(S3C2410_EINTPEND),
 				s3c_irqwake_eintmask);
 }
+
+static inline void s3c_pm_arch_update_uart(void __iomem *regs,
+					   struct pm_uart_save *save)
+{
+}

arch/arm/plat-s3c24xx/include/plat/regs-dma.h

+/* arch/arm/mach-s3c2410/include/mach/dma.h
+ *
+ * Copyright (C) 2003,2004,2006 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C24XX DMA support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* DMA Register definitions */
+
+#define S3C2410_DMA_DISRC		(0x00)
+#define S3C2410_DMA_DISRCC		(0x04)
+#define S3C2410_DMA_DIDST		(0x08)
+#define S3C2410_DMA_DIDSTC		(0x0C)
+#define S3C2410_DMA_DCON		(0x10)
+#define S3C2410_DMA_DSTAT		(0x14)
+#define S3C2410_DMA_DCSRC		(0x18)
+#define S3C2410_DMA_DCDST		(0x1C)
+#define S3C2410_DMA_DMASKTRIG		(0x20)
+#define S3C2412_DMA_DMAREQSEL		(0x24)
+#define S3C2443_DMA_DMAREQSEL		(0x24)
+
+#define S3C2410_DISRCC_INC		(1<<0)
+#define S3C2410_DISRCC_APB		(1<<1)
+
+#define S3C2410_DMASKTRIG_STOP		(1<<2)
+#define S3C2410_DMASKTRIG_ON		(1<<1)
+#define S3C2410_DMASKTRIG_SWTRIG	(1<<0)
+
+#define S3C2410_DCON_DEMAND		(0<<31)
+#define S3C2410_DCON_HANDSHAKE		(1<<31)
+#define S3C2410_DCON_SYNC_PCLK		(0<<30)
+#define S3C2410_DCON_SYNC_HCLK		(1<<30)
+
+#define S3C2410_DCON_INTREQ		(1<<29)
+
+#define S3C2410_DCON_CH0_XDREQ0		(0<<24)
+#define S3C2410_DCON_CH0_UART0		(1<<24)
+#define S3C2410_DCON_CH0_SDI		(2<<24)
+#define S3C2410_DCON_CH0_TIMER		(3<<24)
+#define S3C2410_DCON_CH0_USBEP1		(4<<24)
+
+#define S3C2410_DCON_CH1_XDREQ1		(0<<24)
+#define S3C2410_DCON_CH1_UART1		(1<<24)
+#define S3C2410_DCON_CH1_I2SSDI		(2<<24)
+#define S3C2410_DCON_CH1_SPI		(3<<24)
+#define S3C2410_DCON_CH1_USBEP2		(4<<24)
+
+#define S3C2410_DCON_CH2_I2SSDO		(0<<24)
+#define S3C2410_DCON_CH2_I2SSDI		(1<<24)
+#define S3C2410_DCON_CH2_SDI		(2<<24)
+#define S3C2410_DCON_CH2_TIMER		(3<<24)
+#define S3C2410_DCON_CH2_USBEP3		(4<<24)
+
+#define S3C2410_DCON_CH3_UART2		(0<<24)
+#define S3C2410_DCON_CH3_SDI		(1<<24)
+#define S3C2410_DCON_CH3_SPI		(2<<24)
+#define S3C2410_DCON_CH3_TIMER		(3<<24)
+#define S3C2410_DCON_CH3_USBEP4		(4<<24)
+
+#define S3C2410_DCON_SRCSHIFT		(24)
+#define S3C2410_DCON_SRCMASK		(7<<24)
+
+#define S3C2410_DCON_BYTE		(0<<20)
+#define S3C2410_DCON_HALFWORD		(1<<20)
+#define S3C2410_DCON_WORD		(2<<20)
+
+#define S3C2410_DCON_AUTORELOAD		(0<<22)
+#define S3C2410_DCON_NORELOAD		(1<<22)
+#define S3C2410_DCON_HWTRIG		(1<<23)
+
+#ifdef CONFIG_CPU_S3C2440
+#define S3C2440_DIDSTC_CHKINT		(1<<2)
+
+#define S3C2440_DCON_CH0_I2SSDO		(5<<24)
+#define S3C2440_DCON_CH0_PCMIN		(6<<24)
+
+#define S3C2440_DCON_CH1_PCMOUT		(5<<24)
+#define S3C2440_DCON_CH1_SDI		(6<<24)
+
+#define S3C2440_DCON_CH2_PCMIN		(5<<24)
+#define S3C2440_DCON_CH2_MICIN		(6<<24)
+
+#define S3C2440_DCON_CH3_MICIN		(5<<24)
+#define S3C2440_DCON_CH3_PCMOUT		(6<<24)
+#endif
+
+#ifdef CONFIG_CPU_S3C2412
+
+#define S3C2412_DMAREQSEL_SRC(x)	((x)<<1)
+
+#define S3C2412_DMAREQSEL_HW		(1)
+
+#define S3C2412_DMAREQSEL_SPI0TX	S3C2412_DMAREQSEL_SRC(0)
+#define S3C2412_DMAREQSEL_SPI0RX	S3C2412_DMAREQSEL_SRC(1)
+#define S3C2412_DMAREQSEL_SPI1TX	S3C2412_DMAREQSEL_SRC(2)
+#define S3C2412_DMAREQSEL_SPI1RX	S3C2412_DMAREQSEL_SRC(3)
+#define S3C2412_DMAREQSEL_I2STX		S3C2412_DMAREQSEL_SRC(4)
+#define S3C2412_DMAREQSEL_I2SRX		S3C2412_DMAREQSEL_SRC(5)
+#define S3C2412_DMAREQSEL_TIMER		S3C2412_DMAREQSEL_SRC(9)
+#define S3C2412_DMAREQSEL_SDI		S3C2412_DMAREQSEL_SRC(10)
+#define S3C2412_DMAREQSEL_USBEP1	S3C2412_DMAREQSEL_SRC(13)
+#define S3C2412_DMAREQSEL_USBEP2	S3C2412_DMAREQSEL_SRC(14)
+#define S3C2412_DMAREQSEL_USBEP3	S3C2412_DMAREQSEL_SRC(15)
+#define S3C2412_DMAREQSEL_USBEP4	S3C2412_DMAREQSEL_SRC(16)
+#define S3C2412_DMAREQSEL_XDREQ0	S3C2412_DMAREQSEL_SRC(17)
+#define S3C2412_DMAREQSEL_XDREQ1	S3C2412_DMAREQSEL_SRC(18)
+#define S3C2412_DMAREQSEL_UART0_0	S3C2412_DMAREQSEL_SRC(19)
+#define S3C2412_DMAREQSEL_UART0_1	S3C2412_DMAREQSEL_SRC(20)
+#define S3C2412_DMAREQSEL_UART1_0	S3C2412_DMAREQSEL_SRC(21)
+#define S3C2412_DMAREQSEL_UART1_1	S3C2412_DMAREQSEL_SRC(22)
+#define S3C2412_DMAREQSEL_UART2_0	S3C2412_DMAREQSEL_SRC(23)
+#define S3C2412_DMAREQSEL_UART2_1	S3C2412_DMAREQSEL_SRC(24)
+
+#endif
+
+#define S3C2443_DMAREQSEL_SRC(x)	((x)<<1)
+
+#define S3C2443_DMAREQSEL_HW		(1)
+
+#define S3C2443_DMAREQSEL_SPI0TX	S3C2443_DMAREQSEL_SRC(0)
+#define S3C2443_DMAREQSEL_SPI0RX	S3C2443_DMAREQSEL_SRC(1)
+#define S3C2443_DMAREQSEL_SPI1TX	S3C2443_DMAREQSEL_SRC(2)
+#define S3C2443_DMAREQSEL_SPI1RX	S3C2443_DMAREQSEL_SRC(3)
+#define S3C2443_DMAREQSEL_I2STX		S3C2443_DMAREQSEL_SRC(4)
+#define S3C2443_DMAREQSEL_I2SRX		S3C2443_DMAREQSEL_SRC(5)
+#define S3C2443_DMAREQSEL_TIMER		S3C2443_DMAREQSEL_SRC(9)
+#define S3C2443_DMAREQSEL_SDI		S3C2443_DMAREQSEL_SRC(10)
+#define S3C2443_DMAREQSEL_XDREQ0	S3C2443_DMAREQSEL_SRC(17)
+#define S3C2443_DMAREQSEL_XDREQ1	S3C2443_DMAREQSEL_SRC(18)
+#define S3C2443_DMAREQSEL_UART0_0	S3C2443_DMAREQSEL_SRC(19)
+#define S3C2443_DMAREQSEL_UART0_1	S3C2443_DMAREQSEL_SRC(20)
+#define S3C2443_DMAREQSEL_UART1_0	S3C2443_DMAREQSEL_SRC(21)
+#define S3C2443_DMAREQSEL_UART1_1	S3C2443_DMAREQSEL_SRC(22)
+#define S3C2443_DMAREQSEL_UART2_0	S3C2443_DMAREQSEL_SRC(23)
+#define S3C2443_DMAREQSEL_UART2_1	S3C2443_DMAREQSEL_SRC(24)
+#define S3C2443_DMAREQSEL_UART3_0	S3C2443_DMAREQSEL_SRC(25)
+#define S3C2443_DMAREQSEL_UART3_1	S3C2443_DMAREQSEL_SRC(26)
+#define S3C2443_DMAREQSEL_PCMOUT	S3C2443_DMAREQSEL_SRC(27)
+#define S3C2443_DMAREQSEL_PCMIN 	S3C2443_DMAREQSEL_SRC(28)
+#define S3C2443_DMAREQSEL_MICIN		S3C2443_DMAREQSEL_SRC(29)

arch/arm/plat-s3c24xx/pm.c

@@ -30,6 +30,7 @@
 #include <linux/suspend.h>
 #include <linux/errno.h>
 #include <linux/time.h>
+#include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/serial_core.h>
 #include <linux/io.h>
@@ -75,43 +76,10 @@ static struct sleep_save core_save[] = {
 	SAVE_ITEM(S3C2410_CLKSLOW),
 };
 
-static struct gpio_sleep {
-	void __iomem	*base;
-	unsigned int	 gpcon;
-	unsigned int	 gpdat;
-	unsigned int	 gpup;
-} gpio_save[] = {
-	[0] = {
-		.base	= S3C2410_GPACON,
-	},
-	[1] = {
-		.base	= S3C2410_GPBCON,
-	},
-	[2] = {
-		.base	= S3C2410_GPCCON,
-	},
-	[3] = {
-		.base	= S3C2410_GPDCON,
-	},
-	[4] = {
-		.base	= S3C2410_GPECON,
-	},
-	[5] = {
-		.base	= S3C2410_GPFCON,
-	},
-	[6] = {
-		.base	= S3C2410_GPGCON,
-	},
-	[7] = {
-		.base	= S3C2410_GPHCON,
-	},
-};
-
 static struct sleep_save misc_save[] = {
 	SAVE_ITEM(S3C2410_DCLKCON),
 };
 
-
 /* s3c_pm_check_resume_pin
  *
  * check to see if the pin is configured correctly for sleep mode, and
@@ -156,195 +124,15 @@ void s3c_pm_configure_extint(void)
 	 * and then configure it as an input if it is not
 	*/
 
-	for (pin = S3C2410_GPF0; pin <= S3C2410_GPF7; pin++) {
-		s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF0);
-	}
-
-	for (pin = S3C2410_GPG0; pin <= S3C2410_GPG7; pin++) {
-		s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG0)+8);
+	for (pin = S3C2410_GPF(0); pin <= S3C2410_GPF(7); pin++) {
+		s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF(0));
 	}
-}
-
-/* offsets for CON/DAT/UP registers */
-
-#define OFFS_CON	(S3C2410_GPACON - S3C2410_GPACON)
-#define OFFS_DAT	(S3C2410_GPADAT - S3C2410_GPACON)
-#define OFFS_UP		(S3C2410_GPBUP  - S3C2410_GPBCON)
-
-/* s3c_pm_save_gpios()
- *
- * Save the state of the GPIOs
- */
-
-void s3c_pm_save_gpios(void)
-{
-	struct gpio_sleep *gps = gpio_save;
-	unsigned int gpio;
-
-	for (gpio = 0; gpio < ARRAY_SIZE(gpio_save); gpio++, gps++) {
-		void __iomem *base = gps->base;
-
-		gps->gpcon = __raw_readl(base + OFFS_CON);
-		gps->gpdat = __raw_readl(base + OFFS_DAT);
-
-		if (gpio > 0)
-			gps->gpup = __raw_readl(base + OFFS_UP);
 
+	for (pin = S3C2410_GPG(0); pin <= S3C2410_GPG(7); pin++) {
+		s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG(0))+8);
 	}
 }
 
-/* Test whether the given masked+shifted bits of an GPIO configuration
- * are one of the SFN (special function) modes. */
-
-static inline int is_sfn(unsigned long con)
-{
-	return (con == 2 || con == 3);
-}
-
-/* Test if the given masked+shifted GPIO configuration is an input */
-
-static inline int is_in(unsigned long con)
-{
-	return con == 0;
-}
-
-/* Test if the given masked+shifted GPIO configuration is an output */
-
-static inline int is_out(unsigned long con)
-{
-	return con == 1;
-}
-
-/**
- * s3c2410_pm_restore_gpio() - restore the given GPIO bank
- * @index: The number of the GPIO bank being resumed.
- * @gps: The sleep confgiuration for the bank.
- *
- * Restore one of the GPIO banks that was saved during suspend. This is
- * not as simple as once thought, due to the possibility of glitches
- * from the order that the CON and DAT registers are set in.
- *
- * The three states the pin can be are {IN,OUT,SFN} which gives us 9
- * combinations of changes to check. Three of these, if the pin stays
- * in the same configuration can be discounted. This leaves us with
- * the following:
- *
- * { IN => OUT }  Change DAT first
- * { IN => SFN }  Change CON first
- * { OUT => SFN } Change CON first, so new data will not glitch
- * { OUT => IN }  Change CON first, so new data will not glitch
- * { SFN => IN }  Change CON first
- * { SFN => OUT } Change DAT first, so new data will not glitch [1]
- *
- * We do not currently deal with the UP registers as these control
- * weak resistors, so a small delay in change should not need to bring
- * these into the calculations.
- *
- * [1] this assumes that writing to a pin DAT whilst in SFN will set the
- *     state for when it is next output.
- */
-
-static void s3c2410_pm_restore_gpio(int index, struct gpio_sleep *gps)
-{
-	void __iomem *base = gps->base;
-	unsigned long gps_gpcon = gps->gpcon;
-	unsigned long gps_gpdat = gps->gpdat;
-	unsigned long old_gpcon;
-	unsigned long old_gpdat;
-	unsigned long old_gpup = 0x0;
-	unsigned long gpcon;
-	int nr;
-
-	old_gpcon = __raw_readl(base + OFFS_CON);
-	old_gpdat = __raw_readl(base + OFFS_DAT);
-
-	if (base == S3C2410_GPACON) {
-		/* GPACON only has one bit per control / data and no PULLUPs.
-		 * GPACON[x] = 0 => Output, 1 => SFN */
-
-		/* first set all SFN bits to SFN */
-
-		gpcon = old_gpcon | gps->gpcon;
-		__raw_writel(gpcon, base + OFFS_CON);
-
-		/* now set all the other bits */
-
-		__raw_writel(gps_gpdat, base + OFFS_DAT);
-		__raw_writel(gps_gpcon, base + OFFS_CON);
-	} else {
-		unsigned long old, new, mask;
-		unsigned long change_mask = 0x0;
-
-		old_gpup = __raw_readl(base + OFFS_UP);
-
-		/* Create a change_mask of all the items that need to have
-		 * their CON value changed before their DAT value, so that
-		 * we minimise the work between the two settings.
-		 */
-
-		for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) {
-			old = (old_gpcon & mask) >> nr;
-			new = (gps_gpcon & mask) >> nr;
-
-			/* If there is no change, then skip */
-
-			if (old == new)
-				continue;
-
-			/* If both are special function, then skip */
-
-			if (is_sfn(old) && is_sfn(new))
-				continue;
-
-			/* Change is IN => OUT, do not change now */
-
-			if (is_in(old) && is_out(new))
-				continue;
-
-			/* Change is SFN => OUT, do not change now */
-
-			if (is_sfn(old) && is_out(new))
-				continue;
-
-			/* We should now be at the case of IN=>SFN,
-			 * OUT=>SFN, OUT=>IN, SFN=>IN. */
-
-			change_mask |= mask;
-		}
-
-		/* Write the new CON settings */
-
-		gpcon = old_gpcon & ~change_mask;
-		gpcon |= gps_gpcon & change_mask;
-
-		__raw_writel(gpcon, base + OFFS_CON);
-
-		/* Now change any items that require DAT,CON */
-
-		__raw_writel(gps_gpdat, base + OFFS_DAT);
-		__raw_writel(gps_gpcon, base + OFFS_CON);
-		__raw_writel(gps->gpup, base + OFFS_UP);
-	}
-
-	S3C_PMDBG("GPIO[%d] CON %08lx => %08lx, DAT %08lx => %08lx\n",
-		  index, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
-}
-
-
-/** s3c2410_pm_restore_gpios()
- *
- * Restore the state of the GPIOs
- */
-
-void s3c_pm_restore_gpios(void)
-{
-	struct gpio_sleep *gps = gpio_save;
-	int gpio;
-
-	for (gpio = 0; gpio < ARRAY_SIZE(gpio_save); gpio++, gps++) {
-		s3c2410_pm_restore_gpio(gpio, gps);
-	}
-}
 
 void s3c_pm_restore_core(void)
 {

arch/arm/plat-s3c24xx/setup-i2c.c

@@ -11,6 +11,7 @@
 */
 
 #include <linux/kernel.h>
+#include <linux/gpio.h>
 
 struct platform_device;
 
@@ -20,6 +21,6 @@ struct platform_device;
 
 void s3c_i2c0_cfg_gpio(struct platform_device *dev)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_IICSDA);
-	s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_IICSCL);
+	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA);
+	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL);
 }

arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c

@@ -22,16 +22,16 @@ void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi,
 					  int enable)
 {
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPE13_SPICLK0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE12, S3C2410_GPE12_SPIMOSI0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPE11_SPIMISO0);
-		s3c2410_gpio_pullup(S3C2410_GPE11, 0);
-		s3c2410_gpio_pullup(S3C2410_GPE13, 0);
+		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0);
+		s3c2410_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0);
+		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0);
+		s3c2410_gpio_pullup(S3C2410_GPE(11), 0);
+		s3c2410_gpio_pullup(S3C2410_GPE(13), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPE11, 1);
-		s3c2410_gpio_pullup(S3C2410_GPE12, 1);
-		s3c2410_gpio_pullup(S3C2410_GPE13, 1);
+		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
+		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
+		s3c2410_gpio_pullup(S3C2410_GPE(11), 1);
+		s3c2410_gpio_pullup(S3C2410_GPE(12), 1);
+		s3c2410_gpio_pullup(S3C2410_GPE(13), 1);
 	}
 }

arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c

@@ -22,16 +22,16 @@ void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi,
 				       int enable)
 {
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPG7_SPICLK1);
-		s3c2410_gpio_cfgpin(S3C2410_GPG6, S3C2410_GPG6_SPIMOSI1);
-		s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPG5_SPIMISO1);
-		s3c2410_gpio_pullup(S3C2410_GPG5, 0);
-		s3c2410_gpio_pullup(S3C2410_GPG6, 0);
+		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1);
+		s3c2410_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1);
+		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1);
+		s3c2410_gpio_pullup(S3C2410_GPG(5), 0);
+		s3c2410_gpio_pullup(S3C2410_GPG(6), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPG5, 1);
-		s3c2410_gpio_pullup(S3C2410_GPG6, 1);
-		s3c2410_gpio_pullup(S3C2410_GPG7, 1);
+		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
+		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
+		s3c2410_gpio_pullup(S3C2410_GPG(5), 1);
+		s3c2410_gpio_pullup(S3C2410_GPG(6), 1);
+		s3c2410_gpio_pullup(S3C2410_GPG(7), 1);
 	}
 }

arch/arm/plat-s3c64xx/Kconfig

@@ -19,6 +19,7 @@ config PLAT_S3C64XX
 	select S3C_GPIO_PULL_UPDOWN
 	select S3C_GPIO_CFG_S3C24XX
 	select S3C_GPIO_CFG_S3C64XX
+	select USB_ARCH_HAS_OHCI
 	help
 	  Base platform code for any Samsung S3C64XX device
 
@@ -38,6 +39,10 @@ config CPU_S3C6400_CLOCK
 	  Common clock support code for the S3C6400 that is shared
 	  by other CPUs in the series, such as the S3C6410.
 
+config S3C64XX_DMA
+	bool "S3C64XX DMA"
+	select S3C_DMA
+
 # platform specific device setup
 
 config S3C64XX_SETUP_I2C0
@@ -59,4 +64,9 @@ config S3C64XX_SETUP_FB_24BPP
 	help
 	  Common setup code for S3C64XX with an 24bpp RGB display helper.
 
+config S3C64XX_SETUP_SDHCI_GPIO
+	bool
+	help
+	  Common setup code for S3C64XX SDHCI GPIO configurations
+
 endif

arch/arm/plat-s3c64xx/Makefile

@@ -24,8 +24,19 @@ obj-y				+= gpiolib.o
 obj-$(CONFIG_CPU_S3C6400_INIT)	+= s3c6400-init.o
 obj-$(CONFIG_CPU_S3C6400_CLOCK)	+= s3c6400-clock.o
 
+# PM support
+
+obj-$(CONFIG_PM)		+= pm.o
+obj-$(CONFIG_PM)		+= sleep.o
+obj-$(CONFIG_PM)		+= irq-pm.o
+
+# DMA support
+
+obj-$(CONFIG_S3C64XX_DMA)	+= dma.o
+
 # Device setup
 
 obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0.o
 obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o
 obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o
+obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
\ No newline at end of file

arch/arm/plat-s3c64xx/clock.c

@@ -27,6 +27,12 @@
 #include <plat/devs.h>
 #include <plat/clock.h>
 
+struct clk clk_h2 = {
+	.name		= "hclk2",
+	.id		= -1,
+	.rate		= 0,
+};
+
 struct clk clk_27m = {
 	.name		= "clk_27m",
 	.id		= -1,
@@ -152,6 +158,18 @@ static struct clk init_clocks_disable[] = {
 		.parent		= &clk_48m,
 		.enable		= s3c64xx_sclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_SCLK_MMC2_48,
+	}, {
+		.name		= "dma0",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c64xx_hclk_ctrl,
+		.ctrlbit	= S3C_CLKCON_HCLK_DMA0,
+	}, {
+		.name		= "dma1",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c64xx_hclk_ctrl,
+		.ctrlbit	= S3C_CLKCON_HCLK_DMA1,
 	},
 };
 
@@ -246,6 +264,7 @@ static struct clk *clks[] __initdata = {
 	&clk_epll,
 	&clk_27m,
 	&clk_48m,
+	&clk_h2,
 };
 
 void __init s3c64xx_register_clocks(void)

arch/arm/plat-s3c64xx/cpu.c

@@ -16,6 +16,7 @@
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
+#include <linux/sysdev.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
@@ -101,9 +102,24 @@ static struct map_desc s3c_iodesc[] __initdata = {
 		.pfn		= __phys_to_pfn(S3C64XX_PA_MODEM),
 		.length		= SZ_4K,
 		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (unsigned long)S3C_VA_WATCHDOG,
+		.pfn		= __phys_to_pfn(S3C64XX_PA_WATCHDOG),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE,
 	},
 };
 
+
+struct sysdev_class s3c64xx_sysclass = {
+	.name	= "s3c64xx-core",
+};
+
+static struct sys_device s3c64xx_sysdev = {
+	.cls	= &s3c64xx_sysclass,
+};
+
+
 /* read cpu identification code */
 
 void __init s3c64xx_init_io(struct map_desc *mach_desc, int size)
@@ -115,5 +131,21 @@ void __init s3c64xx_init_io(struct map_desc *mach_desc, int size)
 	iotable_init(mach_desc, size);
 
 	idcode = __raw_readl(S3C_VA_SYS + 0x118);
+	if (!idcode) {
+		/* S3C6400 has the ID register in a different place,
+		 * and needs a write before it can be read. */
+
+		__raw_writel(0x0, S3C_VA_SYS + 0xA1C);
+		idcode = __raw_readl(S3C_VA_SYS + 0xA1C);
+	}
+
 	s3c_init_cpu(idcode, cpu_ids, ARRAY_SIZE(cpu_ids));
 }
+
+static __init int s3c64xx_sysdev_init(void)
+{
+	sysdev_class_register(&s3c64xx_sysclass);
+	return sysdev_register(&s3c64xx_sysdev);
+}
+
+core_initcall(s3c64xx_sysdev_init);

arch/arm/plat-s3c64xx/dma.c

+/* linux/arch/arm/plat-s3c64xx/dma.c
+ *
+ * Copyright 2009 Openmoko, Inc.
+ * Copyright 2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX DMA core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/dmapool.h>
+#include <linux/sysdev.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <mach/dma.h>
+#include <mach/map.h>
+#include <mach/irqs.h>
+
+#include <plat/dma-plat.h>
+#include <plat/regs-sys.h>
+
+#include <asm/hardware/pl080.h>
+
+/* dma channel state information */
+
+struct s3c64xx_dmac {
+	struct sys_device	 sysdev;
+	struct clk		*clk;
+	void __iomem		*regs;
+	struct s3c2410_dma_chan *channels;
+	enum dma_ch		 chanbase;
+};
+
+/* pool to provide LLI buffers */
+static struct dma_pool *dma_pool;
+
+/* Debug configuration and code */
+
+static unsigned char debug_show_buffs = 0;
+
+static void dbg_showchan(struct s3c2410_dma_chan *chan)
+{
+	pr_debug("DMA%d: %08x->%08x L %08x C %08x,%08x S %08x\n",
+		 chan->number,
+		 readl(chan->regs + PL080_CH_SRC_ADDR),
+		 readl(chan->regs + PL080_CH_DST_ADDR),
+		 readl(chan->regs + PL080_CH_LLI),
+		 readl(chan->regs + PL080_CH_CONTROL),
+		 readl(chan->regs + PL080S_CH_CONTROL2),
+		 readl(chan->regs + PL080S_CH_CONFIG));
+}
+
+static void show_lli(struct pl080s_lli *lli)
+{
+	pr_debug("LLI[%p] %08x->%08x, NL %08x C %08x,%08x\n",
+		 lli, lli->src_addr, lli->dst_addr, lli->next_lli,
+		 lli->control0, lli->control1);
+}
+
+static void dbg_showbuffs(struct s3c2410_dma_chan *chan)
+{
+	struct s3c64xx_dma_buff *ptr;
+	struct s3c64xx_dma_buff *end;
+
+	pr_debug("DMA%d: buffs next %p, curr %p, end %p\n",
+		 chan->number, chan->next, chan->curr, chan->end);
+
+	ptr = chan->next;
+	end = chan->end;
+
+	if (debug_show_buffs) {
+		for (; ptr != NULL; ptr = ptr->next) {
+			pr_debug("DMA%d: %08x ",
+				 chan->number, ptr->lli_dma);
+			show_lli(ptr->lli);
+		}
+	}
+}
+
+/* End of Debug */
+
+static struct s3c2410_dma_chan *s3c64xx_dma_map_channel(unsigned int channel)
+{
+	struct s3c2410_dma_chan *chan;
+	unsigned int start, offs;
+
+	start = 0;
+
+	if (channel >= DMACH_PCM1_TX)
+		start = 8;
+
+	for (offs = 0; offs < 8; offs++) {
+		chan = &s3c2410_chans[start + offs];
+		if (!chan->in_use)
+			goto found;
+	}
+
+	return NULL;
+
+found:
+	s3c_dma_chan_map[channel] = chan;
+	return chan;
+}
+
+int s3c2410_dma_config(unsigned int channel, int xferunit)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	switch (xferunit) {
+	case 1:
+		chan->hw_width = 0;
+		break;
+	case 2:
+		chan->hw_width = 1;
+		break;
+	case 4:
+		chan->hw_width = 2;
+		break;
+	default:
+		printk(KERN_ERR "%s: illegal width %d\n", __func__, xferunit);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_config);
+
+static void s3c64xx_dma_fill_lli(struct s3c2410_dma_chan *chan,
+				 struct pl080s_lli *lli,
+				 dma_addr_t data, int size)
+{
+	dma_addr_t src, dst;
+	u32 control0, control1;
+
+	switch (chan->source) {
+	case S3C2410_DMASRC_HW:
+		src = chan->dev_addr;
+		dst = data;
+		control0 = PL080_CONTROL_SRC_AHB2;
+		control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT;
+		control0 |= 2 << PL080_CONTROL_DWIDTH_SHIFT;
+		control0 |= PL080_CONTROL_DST_INCR;
+		break;
+
+	case S3C2410_DMASRC_MEM:
+		src = data;
+		dst = chan->dev_addr;
+		control0 = PL080_CONTROL_DST_AHB2;
+		control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT;
+		control0 |= 2 << PL080_CONTROL_SWIDTH_SHIFT;
+		control0 |= PL080_CONTROL_SRC_INCR;
+		break;
+	default:
+		BUG();
+	}
+
+	/* note, we do not currently setup any of the burst controls */
+
+	control1 = size >> chan->hw_width;	/* size in no of xfers */
+	control0 |= PL080_CONTROL_PROT_SYS;	/* always in priv. mode */
+	control0 |= PL080_CONTROL_TC_IRQ_EN;	/* always fire IRQ */
+
+	lli->src_addr = src;
+	lli->dst_addr = dst;
+	lli->next_lli = 0;
+	lli->control0 = control0;
+	lli->control1 = control1;
+}
+
+static void s3c64xx_lli_to_regs(struct s3c2410_dma_chan *chan,
+				struct pl080s_lli *lli)
+{
+	void __iomem *regs = chan->regs;
+
+	pr_debug("%s: LLI %p => regs\n", __func__, lli);
+	show_lli(lli);
+
+	writel(lli->src_addr, regs + PL080_CH_SRC_ADDR);
+	writel(lli->dst_addr, regs + PL080_CH_DST_ADDR);
+	writel(lli->next_lli, regs + PL080_CH_LLI);
+	writel(lli->control0, regs + PL080_CH_CONTROL);
+	writel(lli->control1, regs + PL080S_CH_CONTROL2);
+}
+
+static int s3c64xx_dma_start(struct s3c2410_dma_chan *chan)
+{
+	struct s3c64xx_dmac *dmac = chan->dmac;
+	u32 config;
+	u32 bit = chan->bit;
+
+	dbg_showchan(chan);
+
+	pr_debug("%s: clearing interrupts\n", __func__);
+
+	/* clear interrupts */
+	writel(bit, dmac->regs + PL080_TC_CLEAR);
+	writel(bit, dmac->regs + PL080_ERR_CLEAR);
+
+	pr_debug("%s: starting channel\n", __func__);
+
+	config = readl(chan->regs + PL080S_CH_CONFIG);
+	config |= PL080_CONFIG_ENABLE;
+
+	pr_debug("%s: writing config %08x\n", __func__, config);
+	writel(config, chan->regs + PL080S_CH_CONFIG);
+
+	return 0;
+}
+
+static int s3c64xx_dma_stop(struct s3c2410_dma_chan *chan)
+{
+	u32 config;
+	int timeout;
+
+	pr_debug("%s: stopping channel\n", __func__);
+
+	dbg_showchan(chan);
+
+	config = readl(chan->regs + PL080S_CH_CONFIG);
+	config |= PL080_CONFIG_HALT;
+	writel(config, chan->regs + PL080S_CH_CONFIG);
+
+	timeout = 1000;
+	do {
+		config = readl(chan->regs + PL080S_CH_CONFIG);
+		pr_debug("%s: %d - config %08x\n", __func__, timeout, config);
+		if (config & PL080_CONFIG_ACTIVE)
+			udelay(10);
+		else
+			break;
+		} while (--timeout > 0);
+
+	if (config & PL080_CONFIG_ACTIVE) {
+		printk(KERN_ERR "%s: channel still active\n", __func__);
+		return -EFAULT;
+	}
+
+	config = readl(chan->regs + PL080S_CH_CONFIG);
+	config &= ~PL080_CONFIG_ENABLE;
+	writel(config, chan->regs + PL080S_CH_CONFIG);
+
+	return 0;
+}
+
+static inline void s3c64xx_dma_bufffdone(struct s3c2410_dma_chan *chan,
+					 struct s3c64xx_dma_buff *buf,
+					 enum s3c2410_dma_buffresult result)
+{
+	if (chan->callback_fn != NULL)
+		(chan->callback_fn)(chan, buf->pw, 0, result);
+}
+
+static void s3c64xx_dma_freebuff(struct s3c64xx_dma_buff *buff)
+{
+	dma_pool_free(dma_pool, buff->lli, buff->lli_dma);
+	kfree(buff);
+}
+
+static int s3c64xx_dma_flush(struct s3c2410_dma_chan *chan)
+{
+	struct s3c64xx_dma_buff *buff, *next;
+	u32 config;
+
+	dbg_showchan(chan);
+
+	pr_debug("%s: flushing channel\n", __func__);
+
+	config = readl(chan->regs + PL080S_CH_CONFIG);
+	config &= ~PL080_CONFIG_ENABLE;
+	writel(config, chan->regs + PL080S_CH_CONFIG);
+
+	/* dump all the buffers associated with this channel */
+
+	for (buff = chan->curr; buff != NULL; buff = next) {
+		next = buff->next;
+		pr_debug("%s: buff %p (next %p)\n", __func__, buff, buff->next);
+
+		s3c64xx_dma_bufffdone(chan, buff, S3C2410_RES_ABORT);
+		s3c64xx_dma_freebuff(buff);
+	}
+
+	chan->curr = chan->next = chan->end = NULL;
+
+	return 0;
+}
+
+int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+	WARN_ON(!chan);
+	if (!chan)
+		return -EINVAL;
+
+	switch (op) {
+	case S3C2410_DMAOP_START:
+		return s3c64xx_dma_start(chan);
+
+	case S3C2410_DMAOP_STOP:
+		return s3c64xx_dma_stop(chan);
+
+	case S3C2410_DMAOP_FLUSH:
+		return s3c64xx_dma_flush(chan);
+
+	/* belive PAUSE/RESUME are no-ops */
+	case S3C2410_DMAOP_PAUSE:
+	case S3C2410_DMAOP_RESUME:
+	case S3C2410_DMAOP_STARTED:
+	case S3C2410_DMAOP_TIMEOUT:
+		return 0;
+	}
+
+	return -ENOENT;
+}
+EXPORT_SYMBOL(s3c2410_dma_ctrl);
+
+/* s3c2410_dma_enque
+ *
+ */
+
+int s3c2410_dma_enqueue(unsigned int channel, void *id,
+			dma_addr_t data, int size)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+	struct s3c64xx_dma_buff *next;
+	struct s3c64xx_dma_buff *buff;
+	struct pl080s_lli *lli;
+	int ret;
+
+	WARN_ON(!chan);
+	if (!chan)
+		return -EINVAL;
+
+	buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_KERNEL);
+	if (!buff) {
+		printk(KERN_ERR "%s: no memory for buffer\n", __func__);
+		return -ENOMEM;
+	}
+
+	lli = dma_pool_alloc(dma_pool, GFP_KERNEL, &buff->lli_dma);
+	if (!lli) {
+		printk(KERN_ERR "%s: no memory for lli\n", __func__);
+		ret = -ENOMEM;
+		goto err_buff;
+	}
+
+	pr_debug("%s: buff %p, dp %08x lli (%p, %08x) %d\n",
+		 __func__, buff, data, lli, (u32)buff->lli_dma, size);
+
+	buff->lli = lli;
+	buff->pw = id;
+
+	s3c64xx_dma_fill_lli(chan, lli, data, size);
+
+	if ((next = chan->next) != NULL) {
+		struct s3c64xx_dma_buff *end = chan->end;
+		struct pl080s_lli *endlli = end->lli;
+
+		pr_debug("enquing onto channel\n");
+
+		end->next = buff;
+		endlli->next_lli = buff->lli_dma;
+
+		if (chan->flags & S3C2410_DMAF_CIRCULAR) {
+			struct s3c64xx_dma_buff *curr = chan->curr;
+			lli->next_lli = curr->lli_dma;
+		}
+
+		if (next == chan->curr) {
+			writel(buff->lli_dma, chan->regs + PL080_CH_LLI);
+			chan->next = buff;
+		}
+
+		show_lli(endlli);
+		chan->end = buff;
+	} else {
+		pr_debug("enquing onto empty channel\n");
+
+		chan->curr = buff;
+		chan->next = buff;
+		chan->end = buff;
+
+		s3c64xx_lli_to_regs(chan, lli);
+	}
+
+	show_lli(lli);
+
+	dbg_showchan(chan);
+	dbg_showbuffs(chan);
+	return 0;
+
+err_buff:
+	kfree(buff);
+	return ret;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_enqueue);
+
+
+int s3c2410_dma_devconfig(int channel,
+			  enum s3c2410_dmasrc source,
+			  unsigned long devaddr)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+	u32 peripheral;
+	u32 config = 0;
+
+	pr_debug("%s: channel %d, source %d, dev %08lx, chan %p\n",
+		 __func__, channel, source, devaddr, chan);
+
+	WARN_ON(!chan);
+	if (!chan)
+		return -EINVAL;
+
+	peripheral = (chan->peripheral & 0xf);
+	chan->source = source;
+	chan->dev_addr = devaddr;
+
+	pr_debug("%s: peripheral %d\n", __func__, peripheral);
+
+	switch (source) {
+	case S3C2410_DMASRC_HW:
+		config = 2 << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+		config |= peripheral << PL080_CONFIG_SRC_SEL_SHIFT;
+		break;
+	case S3C2410_DMASRC_MEM:
+		config = 1 << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+		config |= peripheral << PL080_CONFIG_DST_SEL_SHIFT;
+		break;
+	default:
+		printk(KERN_ERR "%s: bad source\n", __func__);
+		return -EINVAL;
+	}
+
+	/* allow TC and ERR interrupts */
+	config |= PL080_CONFIG_TC_IRQ_MASK;
+	config |= PL080_CONFIG_ERR_IRQ_MASK;
+
+	pr_debug("%s: config %08x\n", __func__, config);
+
+	writel(config, chan->regs + PL080S_CH_CONFIG);
+
+	return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_devconfig);
+
+
+int s3c2410_dma_getposition(unsigned int channel,
+			    dma_addr_t *src, dma_addr_t *dst)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+	WARN_ON(!chan);
+	if (!chan)
+		return -EINVAL;
+
+	if (src != NULL)
+		*src = readl(chan->regs + PL080_CH_SRC_ADDR);
+
+	if (dst != NULL)
+		*dst = readl(chan->regs + PL080_CH_DST_ADDR);
+
+	return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_getposition);
+
+/* s3c2410_request_dma
+ *
+ * get control of an dma channel
+*/
+
+int s3c2410_dma_request(unsigned int channel,
+			struct s3c2410_dma_client *client,
+			void *dev)
+{
+	struct s3c2410_dma_chan *chan;
+	unsigned long flags;
+
+	pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n",
+		 channel, client->name, dev);
+
+	local_irq_save(flags);
+
+	chan = s3c64xx_dma_map_channel(channel);
+	if (chan == NULL) {
+		local_irq_restore(flags);
+		return -EBUSY;
+	}
+
+	dbg_showchan(chan);
+
+	chan->client = client;
+	chan->in_use = 1;
+	chan->peripheral = channel;
+
+	local_irq_restore(flags);
+
+	/* need to setup */
+
+	pr_debug("%s: channel initialised, %p\n", __func__, chan);
+
+	return chan->number | DMACH_LOW_LEVEL;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_request);
+
+/* s3c2410_dma_free
+ *
+ * release the given channel back to the system, will stop and flush
+ * any outstanding transfers, and ensure the channel is ready for the
+ * next claimant.
+ *
+ * Note, although a warning is currently printed if the freeing client
+ * info is not the same as the registrant's client info, the free is still
+ * allowed to go through.
+*/
+
+int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client)
+{
+	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+	unsigned long flags;
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	local_irq_save(flags);
+
+	if (chan->client != client) {
+		printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n",
+		       channel, chan->client, client);
+	}
+
+	/* sort out stopping and freeing the channel */
+
+
+	chan->client = NULL;
+	chan->in_use = 0;
+
+	if (!(channel & DMACH_LOW_LEVEL))
+		s3c_dma_chan_map[channel] = NULL;
+
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_free);
+
+
+static void s3c64xx_dma_tcirq(struct s3c64xx_dmac *dmac, int offs)
+{
+	struct s3c2410_dma_chan *chan = dmac->channels + offs;
+
+	/* note, we currently do not bother to work out which buffer
+	 * or buffers have been completed since the last tc-irq. */
+
+	if (chan->callback_fn)
+		(chan->callback_fn)(chan, chan->curr->pw, 0, S3C2410_RES_OK);
+}
+
+static void s3c64xx_dma_errirq(struct s3c64xx_dmac *dmac, int offs)
+{
+	printk(KERN_DEBUG "%s: offs %d\n", __func__, offs);
+}
+
+static irqreturn_t s3c64xx_dma_irq(int irq, void *pw)
+{
+	struct s3c64xx_dmac *dmac = pw;
+	u32 tcstat, errstat;
+	u32 bit;
+	int offs;
+
+	tcstat = readl(dmac->regs + PL080_TC_STATUS);
+	errstat = readl(dmac->regs + PL080_ERR_STATUS);
+
+	for (offs = 0, bit = 1; offs < 8; offs++, bit <<= 1) {
+		if (tcstat & bit) {
+			writel(bit, dmac->regs + PL080_TC_CLEAR);
+			s3c64xx_dma_tcirq(dmac, offs);
+		}
+
+		if (errstat & bit) {
+			s3c64xx_dma_errirq(dmac, offs);
+			writel(bit, dmac->regs + PL080_ERR_CLEAR);
+		}
+	}
+
+	return IRQ_HANDLED;
+}
+
+static struct sysdev_class dma_sysclass = {
+	.name		= "s3c64xx-dma",
+};
+
+static int s3c64xx_dma_init1(int chno, enum dma_ch chbase,
+			     int irq, unsigned int base)
+{
+	struct s3c2410_dma_chan *chptr = &s3c2410_chans[chno];
+	struct s3c64xx_dmac *dmac;
+	char clkname[16];
+	void __iomem *regs;
+	void __iomem *regptr;
+	int err, ch;
+
+	dmac = kzalloc(sizeof(struct s3c64xx_dmac), GFP_KERNEL);
+	if (!dmac) {
+		printk(KERN_ERR "%s: failed to alloc mem\n", __func__);
+		return -ENOMEM;
+	}
+
+	dmac->sysdev.id = chno / 8;
+	dmac->sysdev.cls = &dma_sysclass;
+
+	err = sysdev_register(&dmac->sysdev);
+	if (err) {
+		printk(KERN_ERR "%s: failed to register sysdevice\n", __func__);
+		goto err_alloc;
+	}
+
+	regs = ioremap(base, 0x200);
+	if (!regs) {
+		printk(KERN_ERR "%s: failed to ioremap()\n", __func__);
+		err = -ENXIO;
+		goto err_dev;
+	}
+
+	snprintf(clkname, sizeof(clkname), "dma%d", dmac->sysdev.id);
+
+	dmac->clk = clk_get(NULL, clkname);
+	if (IS_ERR(dmac->clk)) {
+		printk(KERN_ERR "%s: failed to get clock %s\n", __func__, clkname);
+		err = PTR_ERR(dmac->clk);
+		goto err_map;
+	}
+
+	clk_enable(dmac->clk);
+
+	dmac->regs = regs;
+	dmac->chanbase = chbase;
+	dmac->channels = chptr;
+
+	err = request_irq(irq, s3c64xx_dma_irq, 0, "DMA", dmac);
+	if (err < 0) {
+		printk(KERN_ERR "%s: failed to get irq\n", __func__);
+		goto err_clk;
+	}
+
+	regptr = regs + PL080_Cx_BASE(0);
+
+	for (ch = 0; ch < 8; ch++, chno++, chptr++) {
+		printk(KERN_INFO "%s: registering DMA %d (%p)\n",
+		       __func__, chno, regptr);
+
+		chptr->bit = 1 << ch;
+		chptr->number = chno;
+		chptr->dmac = dmac;
+		chptr->regs = regptr;
+		regptr += PL008_Cx_STRIDE;
+	}
+
+	/* for the moment, permanently enable the controller */
+	writel(PL080_CONFIG_ENABLE, regs + PL080_CONFIG);
+
+	printk(KERN_INFO "PL080: IRQ %d, at %p\n", irq, regs);
+
+	return 0;
+
+err_clk:
+	clk_disable(dmac->clk);
+	clk_put(dmac->clk);
+err_map:
+	iounmap(regs);
+err_dev:
+	sysdev_unregister(&dmac->sysdev);
+err_alloc:
+	kfree(dmac);
+	return err;
+}
+
+static int __init s3c64xx_dma_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "%s: Registering DMA channels\n", __func__);
+
+	dma_pool = dma_pool_create("DMA-LLI", NULL, 32, 16, 0);
+	if (!dma_pool) {
+		printk(KERN_ERR "%s: failed to create pool\n", __func__);
+		return -ENOMEM;
+	}
+
+	ret = sysdev_class_register(&dma_sysclass);
+	if (ret) {
+		printk(KERN_ERR "%s: failed to create sysclass\n", __func__);
+		return -ENOMEM;
+	}
+
+	/* Set all DMA configuration to be DMA, not SDMA */
+	writel(0xffffff, S3C_SYSREG(0x110));
+
+	/* Register standard DMA controlers */
+	s3c64xx_dma_init1(0, DMACH_UART0, IRQ_DMA0, 0x75000000);
+	s3c64xx_dma_init1(8, DMACH_PCM1_TX, IRQ_DMA1, 0x75100000);
+
+	return 0;
+}
+
+arch_initcall(s3c64xx_dma_init);

arch/arm/plat-s3c64xx/gpiolib.c

@@ -385,12 +385,19 @@ static __init void s3c64xx_gpiolib_add_4bit(struct s3c_gpio_chip *chip)
 {
 	chip->chip.direction_input = s3c64xx_gpiolib_4bit_input;
 	chip->chip.direction_output = s3c64xx_gpiolib_4bit_output;
+	chip->pm = __gpio_pm(&s3c_gpio_pm_4bit);
 }
 
 static __init void s3c64xx_gpiolib_add_4bit2(struct s3c_gpio_chip *chip)
 {
 	chip->chip.direction_input = s3c64xx_gpiolib_4bit2_input;
 	chip->chip.direction_output = s3c64xx_gpiolib_4bit2_output;
+	chip->pm = __gpio_pm(&s3c_gpio_pm_4bit);
+}
+
+static __init void s3c64xx_gpiolib_add_2bit(struct s3c_gpio_chip *chip)
+{
+	chip->pm = __gpio_pm(&s3c_gpio_pm_2bit);
 }
 
 static __init void s3c64xx_gpiolib_add(struct s3c_gpio_chip *chips,
@@ -412,7 +419,8 @@ static __init int s3c64xx_gpiolib_init(void)
 	s3c64xx_gpiolib_add(gpio_4bit2, ARRAY_SIZE(gpio_4bit2),
 			    s3c64xx_gpiolib_add_4bit2);
 
-	s3c64xx_gpiolib_add(gpio_2bit, ARRAY_SIZE(gpio_2bit), NULL);
+	s3c64xx_gpiolib_add(gpio_2bit, ARRAY_SIZE(gpio_2bit),
+			    s3c64xx_gpiolib_add_2bit);
 
 	return 0;
 }

arch/arm/plat-s3c64xx/include/plat/dma-plat.h

+/* linux/arch/arm/plat-s3c64xx/include/plat/dma-plat.h
+ *
+ * Copyright 2009 Openmoko, Inc.
+ * Copyright 2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX DMA core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define DMACH_LOW_LEVEL (1<<28) /* use this to specifiy hardware ch no */
+
+struct s3c64xx_dma_buff;
+
+/** s3c64xx_dma_buff - S3C64XX DMA buffer descriptor
+ * @next: Pointer to next buffer in queue or ring.
+ * @pw: Client provided identifier
+ * @lli: Pointer to hardware descriptor this buffer is associated with.
+ * @lli_dma: Hardare address of the descriptor.
+ */
+struct s3c64xx_dma_buff {
+	struct s3c64xx_dma_buff *next;
+
+	void			*pw;
+	struct pl080_lli	*lli;
+	dma_addr_t		 lli_dma;
+};
+
+struct s3c64xx_dmac;
+
+struct s3c2410_dma_chan {
+	unsigned char		 number;      /* number of this dma channel */
+	unsigned char		 in_use;      /* channel allocated */
+	unsigned char		 bit;	      /* bit for enable/disable/etc */
+	unsigned char		 hw_width;
+	unsigned char		 peripheral;
+
+	unsigned int		 flags;
+	enum s3c2410_dmasrc	 source;
+
+
+	dma_addr_t		dev_addr;
+
+	struct s3c2410_dma_client *client;
+	struct s3c64xx_dmac	*dmac;		/* pointer to controller */
+
+	void __iomem		*regs;
+
+	/* cdriver callbacks */
+	s3c2410_dma_cbfn_t	 callback_fn;	/* buffer done callback */
+	s3c2410_dma_opfn_t	 op_fn;		/* channel op callback */
+
+	/* buffer list and information */
+	struct s3c64xx_dma_buff	*curr;		/* current dma buffer */
+	struct s3c64xx_dma_buff	*next;		/* next buffer to load */
+	struct s3c64xx_dma_buff	*end;		/* end of queue */
+
+	/* note, when channel is running in circular mode, curr is the
+	 * first buffer enqueued, end is the last and curr is where the
+	 * last buffer-done event is set-at. The buffers are not freed
+	 * and the last buffer hardware descriptor points back to the
+	 * first.
+	 */
+};
+
+#include <plat/dma-core.h>

arch/arm/plat-s3c64xx/include/plat/irqs.h

@@ -157,6 +157,7 @@
 
 #define S3C_EINT(x)		((x) + S3C_IRQ_EINT_BASE)
 #define IRQ_EINT(x)		S3C_EINT(x)
+#define IRQ_EINT_BIT(x)		((x) - S3C_EINT(0))
 
 /* Next the external interrupt groups. These are similar to the IRQ_EINT(x)
  * that they are sourced from the GPIO pins but with a different scheme for

arch/arm/plat-s3c64xx/include/plat/pm-core.h

+/* linux/arch/arm/plat-s3c64xx/include/plat/pm-core.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *      Ben Dooks <ben@simtec.co.uk>
+ *      http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - PM core support for arch/arm/plat-s3c/pm.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <plat/regs-gpio.h>
+
+static inline void s3c_pm_debug_init_uart(void)
+{
+	u32 tmp = __raw_readl(S3C_PCLK_GATE);
+
+	/* As a note, since the S3C64XX UARTs generally have multiple
+	 * clock sources, we simply enable PCLK at the moment and hope
+	 * that the resume settings for the UART are suitable for the
+	 * use with PCLK.
+	 */
+
+	tmp |= S3C_CLKCON_PCLK_UART0;
+	tmp |= S3C_CLKCON_PCLK_UART1;
+	tmp |= S3C_CLKCON_PCLK_UART2;
+	tmp |= S3C_CLKCON_PCLK_UART3;
+
+	__raw_writel(tmp, S3C_PCLK_GATE);
+	udelay(10);
+}
+
+static inline void s3c_pm_arch_prepare_irqs(void)
+{
+	/* VIC should have already been taken care of */
+
+	/* clear any pending EINT0 interrupts */
+	__raw_writel(__raw_readl(S3C64XX_EINT0PEND), S3C64XX_EINT0PEND);
+}
+
+static inline void s3c_pm_arch_stop_clocks(void)
+{
+}
+
+static inline void s3c_pm_arch_show_resume_irqs(void)
+{
+}
+
+/* make these defines, we currently do not have any need to change
+ * the IRQ wake controls depending on the CPU we are running on */
+
+#define s3c_irqwake_eintallow	((1 << 28) - 1)
+#define s3c_irqwake_intallow	(0)
+
+static inline void s3c_pm_arch_update_uart(void __iomem *regs,
+					   struct pm_uart_save *save)
+{
+	u32 ucon = __raw_readl(regs + S3C2410_UCON);
+	u32 ucon_clk = ucon & S3C6400_UCON_CLKMASK;
+	u32 save_clk = save->ucon & S3C6400_UCON_CLKMASK;
+	u32 new_ucon;
+	u32 delta;
+
+	/* S3C64XX UART blocks only support level interrupts, so ensure that
+	 * when we restore unused UART blocks we force the level interrupt
+	 * settigs. */
+	save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
+
+	/* We have a constraint on changing the clock type of the UART
+	 * between UCLKx and PCLK, so ensure that when we restore UCON
+	 * that the CLK field is correctly modified if the bootloader
+	 * has changed anything.
+	 */
+	if (ucon_clk != save_clk) {
+		new_ucon = save->ucon;
+		delta = ucon_clk ^ save_clk;
+
+		/* change from UCLKx => wrong PCLK,
+		 * either UCLK can be tested for by a bit-test
+		 * with UCLK0 */
+		if (ucon_clk & S3C6400_UCON_UCLK0 &&
+		    !(save_clk & S3C6400_UCON_UCLK0) &&
+		    delta & S3C6400_UCON_PCLK2) {
+			new_ucon &= ~S3C6400_UCON_UCLK0;
+		} else if (delta == S3C6400_UCON_PCLK2) {
+			/* as an precaution, don't change from
+			 * PCLK2 => PCLK or vice-versa */
+			new_ucon ^= S3C6400_UCON_PCLK2;
+		}
+
+		S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n",
+			  ucon, new_ucon, save->ucon);
+		save->ucon = new_ucon;
+	}
+}

arch/arm/plat-s3c64xx/include/plat/regs-clock.h

@@ -32,6 +32,7 @@
 #define S3C_HCLK_GATE		S3C_CLKREG(0x30)
 #define S3C_PCLK_GATE		S3C_CLKREG(0x34)
 #define S3C_SCLK_GATE		S3C_CLKREG(0x38)
+#define S3C_MEM0_GATE		S3C_CLKREG(0x3C)
 
 /* CLKDIV0 */
 #define S3C6400_CLKDIV0_MFC_MASK	(0xf << 28)

arch/arm/plat-s3c64xx/include/plat/s3c6400.h

@@ -15,12 +15,13 @@
 /* Common init code for S3C6400 related SoCs */
 
 extern void s3c6400_common_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-extern void s3c6400_register_clocks(void);
+extern void s3c6400_register_clocks(unsigned armclk_divlimit);
 extern void s3c6400_setup_clocks(void);
 
 #ifdef CONFIG_CPU_S3C6400
 
 extern  int s3c6400_init(void);
+extern void s3c6400_init_irq(void);
 extern void s3c6400_map_io(void);
 extern void s3c6400_init_clocks(int xtal);
 

arch/arm/plat-s3c64xx/irq-eint.c

@@ -14,6 +14,7 @@
 
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
+#include <linux/sysdev.h>
 #include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/io.h>
@@ -26,6 +27,7 @@
 
 #include <mach/map.h>
 #include <plat/cpu.h>
+#include <plat/pm.h>
 
 #define eint_offset(irq)	((irq) - IRQ_EINT(0))
 #define eint_irq_to_bit(irq)	(1 << eint_offset(irq))
@@ -134,6 +136,7 @@ static struct irq_chip s3c_irq_eint = {
 	.mask_ack	= s3c_irq_eint_maskack,
 	.ack		= s3c_irq_eint_ack,
 	.set_type	= s3c_irq_eint_set_type,
+	.set_wake	= s3c_irqext_wake,
 };
 
 /* s3c_irq_demux_eint

arch/arm/plat-s3c64xx/irq-pm.c

+/* arch/arm/plat-s3c64xx/irq-pm.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *      Ben Dooks <ben@simtec.co.uk>
+ *      http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - Interrupt handling Power Management
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/serial_core.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include <mach/map.h>
+
+#include <plat/regs-serial.h>
+#include <plat/regs-timer.h>
+#include <plat/regs-gpio.h>
+#include <plat/cpu.h>
+#include <plat/pm.h>
+
+/* We handled all the IRQ types in this code, to save having to make several
+ * small files to handle each different type separately. Having the EINT_GRP
+ * code here shouldn't be as much bloat as the IRQ table space needed when
+ * they are enabled. The added benefit is we ensure that these registers are
+ * in the same state as we suspended.
+ */
+
+static struct sleep_save irq_save[] = {
+	SAVE_ITEM(S3C64XX_PRIORITY),
+	SAVE_ITEM(S3C64XX_EINT0CON0),
+	SAVE_ITEM(S3C64XX_EINT0CON1),
+	SAVE_ITEM(S3C64XX_EINT0FLTCON0),
+	SAVE_ITEM(S3C64XX_EINT0FLTCON1),
+	SAVE_ITEM(S3C64XX_EINT0FLTCON2),
+	SAVE_ITEM(S3C64XX_EINT0FLTCON3),
+	SAVE_ITEM(S3C64XX_EINT0MASK),
+	SAVE_ITEM(S3C64XX_TINT_CSTAT),
+};
+
+static struct irq_grp_save {
+	u32	fltcon;
+	u32	con;
+	u32	mask;
+} eint_grp_save[5];
+
+static u32 irq_uart_mask[CONFIG_SERIAL_SAMSUNG_UARTS];
+
+static int s3c64xx_irq_pm_suspend(struct sys_device *dev, pm_message_t state)
+{
+	struct irq_grp_save *grp = eint_grp_save;
+	int i;
+
+	S3C_PMDBG("%s: suspending IRQs\n", __func__);
+
+	s3c_pm_do_save(irq_save, ARRAY_SIZE(irq_save));
+
+	for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++)
+		irq_uart_mask[i] = __raw_readl(S3C_VA_UARTx(i) + S3C64XX_UINTM);
+
+	for (i = 0; i < ARRAY_SIZE(eint_grp_save); i++, grp++) {
+		grp->con = __raw_readl(S3C64XX_EINT12CON + (i * 4));
+		grp->mask = __raw_readl(S3C64XX_EINT12MASK + (i * 4));
+		grp->fltcon = __raw_readl(S3C64XX_EINT12FLTCON + (i * 4));
+	}
+
+	return 0;
+}
+
+static int s3c64xx_irq_pm_resume(struct sys_device *dev)
+{
+	struct irq_grp_save *grp = eint_grp_save;
+	int i;
+
+	S3C_PMDBG("%s: resuming IRQs\n", __func__);
+
+	s3c_pm_do_restore(irq_save, ARRAY_SIZE(irq_save));
+
+	for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++)
+		__raw_writel(irq_uart_mask[i], S3C_VA_UARTx(i) + S3C64XX_UINTM);
+
+	for (i = 0; i < ARRAY_SIZE(eint_grp_save); i++, grp++) {
+		__raw_writel(grp->con, S3C64XX_EINT12CON + (i * 4));
+		__raw_writel(grp->mask, S3C64XX_EINT12MASK + (i * 4));
+		__raw_writel(grp->fltcon, S3C64XX_EINT12FLTCON + (i * 4));
+	}
+
+	S3C_PMDBG("%s: IRQ configuration restored\n", __func__);
+	return 0;
+}
+
+static struct sysdev_driver s3c64xx_irq_driver = {
+	.suspend = s3c64xx_irq_pm_suspend,
+	.resume	 = s3c64xx_irq_pm_resume,
+};
+
+static int __init s3c64xx_irq_pm_init(void)
+{
+	return sysdev_driver_register(&s3c64xx_sysclass, &s3c64xx_irq_driver);
+}
+
+arch_initcall(s3c64xx_irq_pm_init);
+

arch/arm/plat-s3c64xx/irq.c

@@ -14,12 +14,14 @@
 
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
+#include <linux/serial_core.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 
 #include <asm/hardware/vic.h>
 
 #include <mach/map.h>
+#include <plat/regs-serial.h>
 #include <plat/regs-timer.h>
 #include <plat/cpu.h>
 
@@ -135,9 +137,6 @@ static inline unsigned int s3c_irq_uart_bit(unsigned int irq)
 }
 
 /* UART interrupt registers, not worth adding to seperate include header */
-#define S3C64XX_UINTP	0x30
-#define S3C64XX_UINTSP	0x34
-#define S3C64XX_UINTM	0x38
 
 static void s3c_irq_uart_mask(unsigned int irq)
 {
@@ -233,8 +232,8 @@ void __init s3c64xx_init_irq(u32 vic0_valid, u32 vic1_valid)
 	printk(KERN_DEBUG "%s: initialising interrupts\n", __func__);
 
 	/* initialise the pair of VICs */
-	vic_init(S3C_VA_VIC0, S3C_VIC0_BASE, vic0_valid);
-	vic_init(S3C_VA_VIC1, S3C_VIC1_BASE, vic1_valid);
+	vic_init(S3C_VA_VIC0, S3C_VIC0_BASE, vic0_valid, 0);
+	vic_init(S3C_VA_VIC1, S3C_VIC1_BASE, vic1_valid, 0);
 
 	/* add the timer sub-irqs */
 

arch/arm/plat-s3c64xx/pm.c

+/* linux/arch/arm/plat-s3c64xx/pm.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX CPU PM support.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/init.h>
+#include <linux/suspend.h>
+#include <linux/serial_core.h>
+#include <linux/io.h>
+
+#include <mach/map.h>
+
+#include <plat/pm.h>
+#include <plat/regs-sys.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-clock.h>
+#include <plat/regs-syscon-power.h>
+#include <plat/regs-gpio-memport.h>
+
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+#include <plat/gpio-bank-n.h>
+
+void s3c_pm_debug_smdkled(u32 set, u32 clear)
+{
+	unsigned long flags;
+	u32 reg;
+
+	local_irq_save(flags);
+	reg = __raw_readl(S3C64XX_GPNCON);
+	reg &= ~(S3C64XX_GPN_CONMASK(12) | S3C64XX_GPN_CONMASK(13) |
+		 S3C64XX_GPN_CONMASK(14) | S3C64XX_GPN_CONMASK(15));
+	reg |= S3C64XX_GPN_OUTPUT(12) | S3C64XX_GPN_OUTPUT(13) |
+	       S3C64XX_GPN_OUTPUT(14) | S3C64XX_GPN_OUTPUT(15);
+	__raw_writel(reg, S3C64XX_GPNCON);
+
+	reg = __raw_readl(S3C64XX_GPNDAT);
+	reg &= ~(clear << 12);
+	reg |= set << 12;
+	__raw_writel(reg, S3C64XX_GPNDAT);
+
+	local_irq_restore(flags);
+}
+#endif
+
+static struct sleep_save core_save[] = {
+	SAVE_ITEM(S3C_APLL_LOCK),
+	SAVE_ITEM(S3C_MPLL_LOCK),
+	SAVE_ITEM(S3C_EPLL_LOCK),
+	SAVE_ITEM(S3C_CLK_SRC),
+	SAVE_ITEM(S3C_CLK_DIV0),
+	SAVE_ITEM(S3C_CLK_DIV1),
+	SAVE_ITEM(S3C_CLK_DIV2),
+	SAVE_ITEM(S3C_CLK_OUT),
+	SAVE_ITEM(S3C_HCLK_GATE),
+	SAVE_ITEM(S3C_PCLK_GATE),
+	SAVE_ITEM(S3C_SCLK_GATE),
+	SAVE_ITEM(S3C_MEM0_GATE),
+
+	SAVE_ITEM(S3C_EPLL_CON1),
+	SAVE_ITEM(S3C_EPLL_CON0),
+
+	SAVE_ITEM(S3C64XX_MEM0DRVCON),
+	SAVE_ITEM(S3C64XX_MEM1DRVCON),
+
+#ifndef CONFIG_CPU_FREQ
+	SAVE_ITEM(S3C_APLL_CON),
+	SAVE_ITEM(S3C_MPLL_CON),
+#endif
+};
+
+static struct sleep_save misc_save[] = {
+	SAVE_ITEM(S3C64XX_AHB_CON0),
+	SAVE_ITEM(S3C64XX_AHB_CON1),
+	SAVE_ITEM(S3C64XX_AHB_CON2),
+	
+	SAVE_ITEM(S3C64XX_SPCON),
+
+	SAVE_ITEM(S3C64XX_MEM0CONSTOP),
+	SAVE_ITEM(S3C64XX_MEM1CONSTOP),
+	SAVE_ITEM(S3C64XX_MEM0CONSLP0),
+	SAVE_ITEM(S3C64XX_MEM0CONSLP1),
+	SAVE_ITEM(S3C64XX_MEM1CONSLP),
+};
+
+void s3c_pm_configure_extint(void)
+{
+	__raw_writel(s3c_irqwake_eintmask, S3C64XX_EINT_MASK);
+}
+
+void s3c_pm_restore_core(void)
+{
+	__raw_writel(0, S3C64XX_EINT_MASK);
+
+	s3c_pm_debug_smdkled(1 << 2, 0);
+
+	s3c_pm_do_restore_core(core_save, ARRAY_SIZE(core_save));
+	s3c_pm_do_restore(misc_save, ARRAY_SIZE(misc_save));
+}
+
+void s3c_pm_save_core(void)
+{
+	s3c_pm_do_save(misc_save, ARRAY_SIZE(misc_save));
+	s3c_pm_do_save(core_save, ARRAY_SIZE(core_save));
+}
+
+/* since both s3c6400 and s3c6410 share the same sleep pm calls, we
+ * put the per-cpu code in here until any new cpu comes along and changes
+ * this.
+ */
+
+#include <plat/regs-gpio.h>
+
+static void s3c64xx_cpu_suspend(void)
+{
+	unsigned long tmp;
+
+	/* set our standby method to sleep */
+
+	tmp = __raw_readl(S3C64XX_PWR_CFG);
+	tmp &= ~S3C64XX_PWRCFG_CFG_WFI_MASK;
+	tmp |= S3C64XX_PWRCFG_CFG_WFI_SLEEP;
+	__raw_writel(tmp, S3C64XX_PWR_CFG);
+
+	/* clear any old wakeup */
+
+	__raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT),
+		     S3C64XX_WAKEUP_STAT);
+
+	/* set the LED state to 0110 over sleep */
+	s3c_pm_debug_smdkled(3 << 1, 0xf);
+
+	/* issue the standby signal into the pm unit. Note, we
+	 * issue a write-buffer drain just in case */
+
+	tmp = 0;
+
+	asm("b 1f\n\t"
+	    ".align 5\n\t"
+	    "1:\n\t"
+	    "mcr p15, 0, %0, c7, c10, 5\n\t"
+	    "mcr p15, 0, %0, c7, c10, 4\n\t"
+	    "mcr p15, 0, %0, c7, c0, 4" :: "r" (tmp));
+
+	/* we should never get past here */
+
+	panic("sleep resumed to originator?");
+}
+
+static void s3c64xx_pm_prepare(void)
+{
+	/* store address of resume. */
+	__raw_writel(virt_to_phys(s3c_cpu_resume), S3C64XX_INFORM0);
+
+	/* ensure previous wakeup state is cleared before sleeping */
+	__raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT), S3C64XX_WAKEUP_STAT);
+}
+
+static int s3c64xx_pm_init(void)
+{
+	pm_cpu_prep = s3c64xx_pm_prepare;
+	pm_cpu_sleep = s3c64xx_cpu_suspend;
+	pm_uart_udivslot = 1;
+	return 0;
+}
+
+arch_initcall(s3c64xx_pm_init);

arch/arm/plat-s3c64xx/s3c6400-clock.c

@@ -133,6 +133,65 @@ static struct clksrc_clk clk_mout_mpll = {
 	.sources	= &clk_src_mpll,
 };
 
+static unsigned int armclk_mask;
+
+static unsigned long s3c64xx_clk_arm_get_rate(struct clk *clk)
+{
+	unsigned long rate = clk_get_rate(clk->parent);
+	u32 clkdiv;
+
+	/* divisor mask starts at bit0, so no need to shift */
+	clkdiv = __raw_readl(S3C_CLK_DIV0) & armclk_mask;
+
+	return rate / (clkdiv + 1);
+}
+
+static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk,
+						unsigned long rate)
+{
+	unsigned long parent = clk_get_rate(clk->parent);
+	u32 div;
+
+	if (parent < rate)
+		return rate;
+
+	div = (parent / rate) - 1;
+	if (div > armclk_mask)
+		div = armclk_mask;
+
+	return parent / (div + 1);
+}
+
+static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent = clk_get_rate(clk->parent);
+	u32 div;
+	u32 val;
+
+	if (rate < parent / (armclk_mask + 1))
+		return -EINVAL;
+
+	rate = clk_round_rate(clk, rate);
+	div = clk_get_rate(clk->parent) / rate;
+
+	val = __raw_readl(S3C_CLK_DIV0);
+	val &= armclk_mask;
+	val |= (div - 1);
+	__raw_writel(val, S3C_CLK_DIV0);
+
+	return 0;
+
+}
+
+static struct clk clk_arm = {
+	.name		= "armclk",
+	.id		= -1,
+	.parent		= &clk_mout_apll.clk,
+	.get_rate	= s3c64xx_clk_arm_get_rate,
+	.set_rate	= s3c64xx_clk_arm_set_rate,
+	.round_rate	= s3c64xx_clk_arm_round_rate,
+};
+
 static unsigned long s3c64xx_clk_doutmpll_get_rate(struct clk *clk)
 {
 	unsigned long rate = clk_get_rate(clk->parent);
@@ -520,6 +579,33 @@ static struct clksrc_clk clk_irda = {
 	.reg_divider	= S3C_CLK_DIV2,
 };
 
+static struct clk *clkset_camif_list[] = {
+	&clk_h2,
+};
+
+static struct clk_sources clkset_camif = {
+	.sources	= clkset_camif_list,
+	.nr_sources	= ARRAY_SIZE(clkset_camif_list),
+};
+
+static struct clksrc_clk clk_camif = {
+	.clk	= {
+		.name		= "camera",
+		.id		= -1,
+		.ctrlbit        = S3C_CLKCON_SCLK_CAM,
+		.enable		= s3c64xx_sclk_ctrl,
+		.set_parent	= s3c64xx_setparent_clksrc,
+		.get_rate	= s3c64xx_getrate_clksrc,
+		.set_rate	= s3c64xx_setrate_clksrc,
+		.round_rate	= s3c64xx_roundrate_clksrc,
+	},
+	.shift		= 0,
+	.mask		= 0,
+	.sources	= &clkset_camif,
+	.divider_shift	= S3C6400_CLKDIV0_CAM_SHIFT,
+	.reg_divider	= S3C_CLK_DIV0,
+};
+
 /* Clock initialisation code */
 
 static struct clksrc_clk *init_parents[] = {
@@ -536,6 +622,7 @@ static struct clksrc_clk *init_parents[] = {
 	&clk_audio0,
 	&clk_audio1,
 	&clk_irda,
+	&clk_camif,
 };
 
 static void __init_or_cpufreq s3c6400_set_clksrc(struct clksrc_clk *clk)
@@ -608,6 +695,7 @@ void __init_or_cpufreq s3c6400_setup_clocks(void)
 	clk_fout_epll.rate = epll;
 	clk_fout_apll.rate = apll;
 
+	clk_h2.rate = hclk2;
 	clk_h.rate = hclk;
 	clk_p.rate = pclk;
 	clk_f.rate = fclk;
@@ -635,14 +723,30 @@ static struct clk *clks[] __initdata = {
 	&clk_audio0.clk,
 	&clk_audio1.clk,
 	&clk_irda.clk,
+	&clk_camif.clk,
+	&clk_arm,
 };
 
-void __init s3c6400_register_clocks(void)
+/**
+ * s3c6400_register_clocks - register clocks for s3c6400 and above
+ * @armclk_divlimit: Divisor mask for ARMCLK
+ *
+ * Register the clocks for the S3C6400 and above SoC range, such
+ * as ARMCLK and the clocks which have divider chains attached.
+ *
+ * This call does not setup the clocks, which is left to the
+ * s3c6400_setup_clocks() call which may be needed by the cpufreq
+ * or resume code to re-set the clocks if the bootloader has changed
+ * them.
+ */
+void __init s3c6400_register_clocks(unsigned armclk_divlimit)
 {
 	struct clk *clkp;
 	int ret;
 	int ptr;
 
+	armclk_mask = armclk_divlimit;
+
 	for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) {
 		clkp = clks[ptr];
 		ret = s3c24xx_register_clock(clkp);

arch/arm/plat-s3c64xx/setup-sdhci-gpio.c

+/* linux/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c
+ *
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - Helper functions for setting up SDHCI device(s) GPIO (HSMMC)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <mach/gpio.h>
+#include <plat/gpio-cfg.h>
+
+void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
+{
+	unsigned int gpio;
+	unsigned int end;
+
+	end = S3C64XX_GPG(2 + width);
+
+	/* Set all the necessary GPG pins to special-function 0 */
+	for (gpio = S3C64XX_GPG(0); gpio < end; gpio++) {
+		s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+		s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
+	}
+
+	s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
+	s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(2));
+}
+
+void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *dev, int width)
+{
+	unsigned int gpio;
+	unsigned int end;
+
+	end = S3C64XX_GPH(2 + width);
+
+	/* Set all the necessary GPG pins to special-function 0 */
+	for (gpio = S3C64XX_GPH(0); gpio < end; gpio++) {
+		s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+		s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
+	}
+
+	s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
+	s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(3));
+}

arch/arm/plat-s3c64xx/sleep.S

+/* linux/0arch/arm/plat-s3c64xx/sleep.S
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX CPU sleep code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <mach/map.h>
+
+#undef S3C64XX_VA_GPIO
+#define S3C64XX_VA_GPIO (0x0)
+
+#include <plat/regs-gpio.h>
+#include <plat/gpio-bank-n.h>
+
+#define LL_UART (S3C_PA_UART + (0x400 * CONFIG_S3C_LOWLEVEL_UART_PORT))
+
+	.text
+
+	/* s3c_cpu_save
+	 *
+	 * Save enough processor state to allow the restart of the pm.c
+	 * code after resume.
+	 *
+	 * entry:
+	 *	r0 = pointer to the save block
+	*/
+
+ENTRY(s3c_cpu_save)
+	stmfd	sp!, { r4 - r12, lr }
+
+	mrc	p15, 0, r4, c13, c0, 0	@ FCSE/PID
+	mrc	p15, 0, r5, c3, c0, 0	@ Domain ID
+	mrc	p15, 0, r6, c2, c0, 0	@ Translation Table BASE0
+	mrc	p15, 0, r7, c2, c0, 1	@ Translation Table BASE1
+	mrc	p15, 0, r8, c2, c0, 2	@ Translation Table Control
+	mrc	p15, 0, r9, c1, c0, 0	@ Control register
+	mrc	p15, 0, r10, c1, c0, 1	@ Auxiliary control register
+	mrc	p15, 0, r11, c1, c0, 2	@ Co-processor access controls
+
+	stmia	r0, { r4 - r13 }	@ Save CP registers and SP
+
+	@@ save our state to ram
+	bl	s3c_pm_cb_flushcache
+
+	@@ call final suspend code
+	ldr	r0, =pm_cpu_sleep
+	ldr	pc, [r0]
+	
+	@@ return to the caller, after the MMU is turned on.
+	@@ restore the last bits of the stack and return.
+resume_with_mmu:
+	ldmfd	sp!, { r4 - r12, pc }	@ return, from sp from s3c_cpu_save
+
+	.data
+
+	/* the next bit is code, but it requires easy access to the
+	 * s3c_sleep_save_phys data before the MMU is switched on, so
+	 * we store the code that needs this variable in the .data where
+	 * the value can be written to (the .text segment is RO).
+	*/
+
+	.global	s3c_sleep_save_phys
+s3c_sleep_save_phys:
+	.word	0
+
+	/* Sleep magic, the word before the resume entry point so that the
+	 * bootloader can check for a resumeable image. */
+
+	.word	0x2bedf00d
+
+	/* s3c_cpu_reusme
+	 *
+	 * This is the entry point, stored by whatever method the bootloader
+	 * requires to get the kernel runnign again. This code expects to be
+	 * entered with no caches live and the MMU disabled. It will then
+	 * restore the MMU and other basic CP registers saved and restart
+	 * the kernel C code to finish the resume code.
+	*/
+
+ENTRY(s3c_cpu_resume)
+	msr	cpsr_c, #PSR_I_BIT | PSR_F_BIT | SVC_MODE
+	ldr	r2, =LL_UART		/* for debug */
+
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+	/* Initialise the GPIO state if we are debugging via the SMDK LEDs,
+	 * as the uboot version supplied resets these to inputs during the
+	 * resume checks.
+	*/
+
+	ldr	r3, =S3C64XX_PA_GPIO
+	ldr	r0, [ r3, #S3C64XX_GPNCON ]
+	bic	r0, r0, #(S3C64XX_GPN_CONMASK(12) | S3C64XX_GPN_CONMASK(13) | \
+			  S3C64XX_GPN_CONMASK(14) | S3C64XX_GPN_CONMASK(15))
+	orr	r0, r0, #(S3C64XX_GPN_OUTPUT(12) | S3C64XX_GPN_OUTPUT(13) | \
+			  S3C64XX_GPN_OUTPUT(14) | S3C64XX_GPN_OUTPUT(15))
+	str	r0, [ r3, #S3C64XX_GPNCON ]
+
+	ldr	r0, [ r3, #S3C64XX_GPNDAT ]
+	bic	r0, r0, #0xf << 12			@ GPN12..15
+	orr	r0, r0, #1 << 15			@ GPN15
+	str	r0, [ r3, #S3C64XX_GPNDAT ]
+#endif
+
+	/* __v6_setup from arch/arm/mm/proc-v6.S, ensure that the caches
+	 * are thoroughly cleaned just in case the bootloader didn't do it
+	 * for us. */
+	mov	r0, #0
+	mcr	p15, 0, r0, c7, c14, 0		@ clean+invalidate D cache
+	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
+	mcr	p15, 0, r0, c7, c15, 0		@ clean+invalidate cache
+	mcr	p15, 0, r0, c7, c10, 4		@ drain write buffer
+	@@mcr	p15, 0, r0, c8, c7, 0		@ invalidate I + D TLBs
+	@@mcr	p15, 0, r0, c7, c7, 0		@ Invalidate I + D caches
+
+	ldr	r0, s3c_sleep_save_phys
+	ldmia	r0, { r4 - r13 }
+
+	mcr	p15, 0, r4, c13, c0, 0	@ FCSE/PID
+	mcr	p15, 0, r5, c3, c0, 0	@ Domain ID
+	mcr	p15, 0, r6, c2, c0, 0	@ Translation Table BASE0
+	mcr	p15, 0, r7, c2, c0, 1	@ Translation Table BASE1
+	mcr	p15, 0, r8, c2, c0, 2	@ Translation Table Control
+	mcr	p15, 0, r10, c1, c0, 1	@ Auxiliary control register
+
+	mov	r0, #0			@ restore copro access controls
+	mcr	p15, 0, r11, c1, c0, 2	@ Co-processor access controls
+	mcr 	p15, 0, r0, c7, c5, 4
+
+	ldr	r2, =resume_with_mmu
+	mcr	p15, 0, r9, c1, c0, 0		/* turn mmu back on */
+	nop
+	mov	pc, r2				/* jump back */
+
+	.end

drivers/leds/leds-h1940.c

@@ -16,6 +16,8 @@
 #include <linux/string.h>
 #include <linux/ctype.h>
 #include <linux/leds.h>
+#include <linux/gpio.h>
+
 #include <mach/regs-gpio.h>
 #include <mach/hardware.h>
 #include <mach/h1940-latch.h>

drivers/leds/leds-s3c24xx.c

@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/leds.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <mach/regs-gpio.h>

drivers/mmc/host/s3cmci.c

@@ -17,6 +17,7 @@
 #include <linux/mmc/host.h>
 #include <linux/platform_device.h>
 #include <linux/cpufreq.h>
+#include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 
@@ -789,7 +790,7 @@ static void s3cmci_dma_setup(struct s3cmci_host *host,
 
 	last_source = source;
 
-	s3c2410_dma_devconfig(host->dma, source, 3,
+	s3c2410_dma_devconfig(host->dma, source,
 			      host->mem->start + host->sdidata);
 
 	if (!setup_ok) {
@@ -1121,7 +1122,7 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	case MMC_POWER_OFF:
 	default:
 		s3c2410_gpio_setpin(S3C2410_GPE5, 0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP);
+		s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPIO_OUTPUT);
 
 		if (host->is2440)
 			mci_con |= S3C2440_SDICON_SDRESET;

drivers/spi/spi_s3c24xx_gpio.c

@@ -17,6 +17,7 @@
 #include <linux/spinlock.h>
 #include <linux/workqueue.h>
 #include <linux/platform_device.h>
+#include <linux/gpio.h>
 
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_bitbang.h>

sound/soc/s3c24xx/s3c2412-i2s.c

@@ -20,6 +20,7 @@
 #include <linux/module.h>
 #include <linux/device.h>
 #include <linux/delay.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/kernel.h>
 #include <linux/io.h>

sound/soc/s3c24xx/s3c2443-ac97.c

@@ -19,6 +19,7 @@
 #include <linux/io.h>
 #include <linux/wait.h>
 #include <linux/delay.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 
 #include <sound/core.h>

sound/soc/s3c24xx/s3c24xx-i2s.c

@@ -21,6 +21,8 @@
 #include <linux/clk.h>
 #include <linux/jiffies.h>
 #include <linux/io.h>
+#include <linux/gpio.h>
+
 #include <sound/core.h>
 #include <sound/pcm.h>
 #include <sound/pcm_params.h>

sound/soc/s3c24xx/s3c24xx-pcm.c

@@ -218,24 +218,17 @@ static int s3c24xx_pcm_prepare(struct snd_pcm_substream *substream)
 	 * sync to pclk, half-word transfers to the IIS-FIFO. */
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
 		s3c2410_dma_devconfig(prtd->params->channel,
-				S3C2410_DMASRC_MEM, S3C2410_DISRCC_INC |
-				S3C2410_DISRCC_APB, prtd->params->dma_addr);
-
-		s3c2410_dma_config(prtd->params->channel,
-				prtd->params->dma_size,
-				S3C2410_DCON_SYNC_PCLK |
-				S3C2410_DCON_HANDSHAKE);
+				      S3C2410_DMASRC_MEM,
+				      prtd->params->dma_addr);
 	} else {
-		s3c2410_dma_config(prtd->params->channel,
-				prtd->params->dma_size,
-				S3C2410_DCON_HANDSHAKE |
-				S3C2410_DCON_SYNC_PCLK);
-
 		s3c2410_dma_devconfig(prtd->params->channel,
-					S3C2410_DMASRC_HW, 0x3,
-					prtd->params->dma_addr);
+				      S3C2410_DMASRC_HW,
+				      prtd->params->dma_addr);
 	}
 
+	s3c2410_dma_config(prtd->params->channel,
+			   prtd->params->dma_size);
+
 	/* flush the DMA channel */
 	s3c2410_dma_ctrl(prtd->params->channel, S3C2410_DMAOP_FLUSH);
 	prtd->dma_loaded = 0;