Init FHC controller registers earlier so that

Zilog interrupt mappings are not clobbered on
Sun Enterprise servers.
Fix some FHC register offsets.
Sometimes IPIs can allow BHs to run with interrupts
disabled, fix that by rescheduling them to normal
PIL based interrupts.

arch/sparc64/kernel/central.c

@@ -247,6 +247,55 @@ static void probe_clock_board(struct linux_central *central,
 	       (central->clkver ? upa_readb(central->clkver) : 0x00));
 }
 
+static void init_all_fhc_hw(void)
+{
+	struct linux_fhc *fhc;
+
+	for(fhc = fhc_list; fhc != NULL; fhc = fhc->next) {
+		u32 tmp;
+
+		/* Clear all of the interrupt mapping registers
+		 * just in case OBP left them in a foul state.
+		 */
+#define ZAP(ICLR, IMAP) \
+do {	u32 imap_tmp; \
+	upa_writel(0, (ICLR)); \
+	upa_readl(ICLR); \
+	imap_tmp = upa_readl(IMAP); \
+	imap_tmp &= ~(0x80000000); \
+	upa_writel(imap_tmp, (IMAP)); \
+	upa_readl(IMAP); \
+} while (0)
+
+		ZAP(fhc->fhc_regs.ffregs + FHC_FFREGS_ICLR,
+		    fhc->fhc_regs.ffregs + FHC_FFREGS_IMAP);
+		ZAP(fhc->fhc_regs.sregs + FHC_SREGS_ICLR,
+		    fhc->fhc_regs.sregs + FHC_SREGS_IMAP);
+		ZAP(fhc->fhc_regs.uregs + FHC_UREGS_ICLR,
+		    fhc->fhc_regs.uregs + FHC_UREGS_IMAP);
+		ZAP(fhc->fhc_regs.tregs + FHC_TREGS_ICLR,
+		    fhc->fhc_regs.tregs + FHC_TREGS_IMAP);
+
+#undef ZAP
+
+		/* Setup FHC control register. */
+		tmp = upa_readl(fhc->fhc_regs.pregs + FHC_PREGS_CTRL);
+
+		/* All non-central boards have this bit set. */
+		if(! IS_CENTRAL_FHC(fhc))
+			tmp |= FHC_CONTROL_IXIST;
+
+		/* For all FHCs, clear the firmware synchronization
+		 * line and both low power mode enables.
+		 */
+		tmp &= ~(FHC_CONTROL_AOFF | FHC_CONTROL_BOFF | FHC_CONTROL_SLINE);
+
+		upa_writel(tmp, fhc->fhc_regs.pregs + FHC_PREGS_CTRL);
+		upa_readl(fhc->fhc_regs.pregs + FHC_PREGS_CTRL);
+	}
+
+}
+
 void central_probe(void)
 {
 	struct linux_prom_registers fpregs[6];
@@ -341,6 +390,8 @@ void central_probe(void)
 	       ((err & FHC_ID_MANUF) >> 1));
 
 	probe_other_fhcs();
+
+	init_all_fhc_hw();
 }
 
 static __inline__ void fhc_ledblink(struct linux_fhc *fhc, int on)
@@ -398,56 +449,12 @@ static void sunfire_timer(unsigned long __ignored)
 void firetruck_init(void)
 {
 	struct linux_central *central = central_bus;
-	struct linux_fhc *fhc;
 	u8 ctrl;
 
 	/* No central bus, nothing to do. */
 	if (central == NULL)
 		return;
 
-	for(fhc = fhc_list; fhc != NULL; fhc = fhc->next) {
-		u32 tmp;
-
-		/* Clear all of the interrupt mapping registers
-		 * just in case OBP left them in a foul state.
-		 */
-#define ZAP(ICLR, IMAP) \
-do {	u32 imap_tmp; \
-	upa_writel(0, (ICLR)); \
-	upa_readl(ICLR); \
-	imap_tmp = upa_readl(IMAP); \
-	imap_tmp &= ~(0x80000000); \
-	upa_writel(imap_tmp, (IMAP)); \
-	upa_readl(IMAP); \
-} while (0)
-
-		ZAP(fhc->fhc_regs.ffregs + FHC_FFREGS_ICLR,
-		    fhc->fhc_regs.ffregs + FHC_FFREGS_IMAP);
-		ZAP(fhc->fhc_regs.sregs + FHC_SREGS_ICLR,
-		    fhc->fhc_regs.sregs + FHC_SREGS_IMAP);
-		ZAP(fhc->fhc_regs.uregs + FHC_UREGS_ICLR,
-		    fhc->fhc_regs.uregs + FHC_UREGS_IMAP);
-		ZAP(fhc->fhc_regs.tregs + FHC_TREGS_ICLR,
-		    fhc->fhc_regs.tregs + FHC_TREGS_IMAP);
-
-#undef ZAP
-
-		/* Setup FHC control register. */
-		tmp = upa_readl(fhc->fhc_regs.pregs + FHC_PREGS_CTRL);
-
-		/* All non-central boards have this bit set. */
-		if(! IS_CENTRAL_FHC(fhc))
-			tmp |= FHC_CONTROL_IXIST;
-
-		/* For all FHCs, clear the firmware synchronization
-		 * line and both low power mode enables.
-		 */
-		tmp &= ~(FHC_CONTROL_AOFF | FHC_CONTROL_BOFF | FHC_CONTROL_SLINE);
-
-		upa_writel(tmp, fhc->fhc_regs.pregs + FHC_PREGS_CTRL);
-		upa_readl(fhc->fhc_regs.pregs + FHC_PREGS_CTRL);
-	}
-
 	/* OBP leaves it on, turn it off so clock board timer LED
 	 * is in sync with FHC ones.
 	 */

arch/sparc64/kernel/pci_psycho.c

@@ -326,15 +326,15 @@ static unsigned char psycho_pil_table[] = {
 /*0x14*/0, 0, 0, 0,	/* PCI B slot 1  Int A, B, C, D */
 /*0x18*/0, 0, 0, 0,	/* PCI B slot 2  Int A, B, C, D */
 /*0x1c*/0, 0, 0, 0,	/* PCI B slot 3  Int A, B, C, D */
-/*0x20*/3,		/* SCSI				*/
+/*0x20*/4,		/* SCSI				*/
 /*0x21*/5,		/* Ethernet			*/
 /*0x22*/8,		/* Parallel Port		*/
 /*0x23*/13,		/* Audio Record			*/
 /*0x24*/14,		/* Audio Playback		*/
 /*0x25*/15,		/* PowerFail			*/
-/*0x26*/3,		/* second SCSI			*/
+/*0x26*/4,		/* second SCSI			*/
 /*0x27*/11,		/* Floppy			*/
-/*0x28*/2,		/* Spare Hardware		*/
+/*0x28*/4,		/* Spare Hardware		*/
 /*0x29*/9,		/* Keyboard			*/
 /*0x2a*/4,		/* Mouse			*/
 /*0x2b*/12,		/* Serial			*/
@@ -353,7 +353,7 @@ static int __init psycho_ino_to_pil(struct pci_dev *pdev, unsigned int ino)
 
 	ret = psycho_pil_table[ino];
 	if (ret == 0 && pdev == NULL) {
-		ret = 2;
+		ret = 4;
 	} else if (ret == 0) {
 		switch ((pdev->class >> 16) & 0xff) {
 		case PCI_BASE_CLASS_STORAGE:
@@ -376,7 +376,7 @@ static int __init psycho_ino_to_pil(struct pci_dev *pdev, unsigned int ino)
 			break;
 
 		default:
-			ret = 2;
+			ret = 4;
 			break;
 		};
 	}

arch/sparc64/kernel/pci_sabre.c

@@ -564,15 +564,15 @@ static unsigned char sabre_pil_table[] = {
 /*0x14*/0, 0, 0, 0,	/* PCI B slot 1  Int A, B, C, D */
 /*0x18*/0, 0, 0, 0,	/* PCI B slot 2  Int A, B, C, D */
 /*0x1c*/0, 0, 0, 0,	/* PCI B slot 3  Int A, B, C, D */
-/*0x20*/3,		/* SCSI				*/
+/*0x20*/4,		/* SCSI				*/
 /*0x21*/5,		/* Ethernet			*/
 /*0x22*/8,		/* Parallel Port		*/
 /*0x23*/13,		/* Audio Record			*/
 /*0x24*/14,		/* Audio Playback		*/
 /*0x25*/15,		/* PowerFail			*/
-/*0x26*/3,		/* second SCSI			*/
+/*0x26*/4,		/* second SCSI			*/
 /*0x27*/11,		/* Floppy			*/
-/*0x28*/2,		/* Spare Hardware		*/
+/*0x28*/4,		/* Spare Hardware		*/
 /*0x29*/9,		/* Keyboard			*/
 /*0x2a*/4,		/* Mouse			*/
 /*0x2b*/12,		/* Serial			*/
@@ -596,7 +596,7 @@ static int __init sabre_ino_to_pil(struct pci_dev *pdev, unsigned int ino)
 
 	ret = sabre_pil_table[ino];
 	if (ret == 0 && pdev == NULL) {
-		ret = 2;
+		ret = 4;
 	} else if (ret == 0) {
 		switch ((pdev->class >> 16) & 0xff) {
 		case PCI_BASE_CLASS_STORAGE:
@@ -619,7 +619,7 @@ static int __init sabre_ino_to_pil(struct pci_dev *pdev, unsigned int ino)
 			break;
 
 		default:
-			ret = 2;
+			ret = 4;
 			break;
 		};
 	}

arch/sparc64/kernel/pci_schizo.c

@@ -291,8 +291,8 @@ static unsigned char schizo_pil_table[] = {
 /*0x0c*/0, 0, 0, 0,	/* PCI slot 3  Int A, B, C, D	*/
 /*0x10*/0, 0, 0, 0,	/* PCI slot 4  Int A, B, C, D	*/
 /*0x14*/0, 0, 0, 0,	/* PCI slot 5  Int A, B, C, D	*/
-/*0x18*/3,		/* SCSI				*/
-/*0x19*/3,		/* second SCSI			*/
+/*0x18*/4,		/* SCSI				*/
+/*0x19*/4,		/* second SCSI			*/
 /*0x1a*/0,		/* UNKNOWN			*/
 /*0x1b*/0,		/* UNKNOWN			*/
 /*0x1c*/8,		/* Parallel			*/
@@ -302,7 +302,7 @@ static unsigned char schizo_pil_table[] = {
 /*0x20*/13,		/* Audio Record			*/
 /*0x21*/14,		/* Audio Playback		*/
 /*0x22*/12,		/* Serial			*/
-/*0x23*/2,		/* EBUS I2C 			*/
+/*0x23*/4,		/* EBUS I2C 			*/
 /*0x24*/10,		/* RTC Clock			*/
 /*0x25*/11,		/* Floppy			*/
 /*0x26*/0,		/* UNKNOWN			*/
@@ -344,7 +344,7 @@ static int __init schizo_ino_to_pil(struct pci_dev *pdev, unsigned int ino)
 
 	ret = schizo_pil_table[ino];
 	if (ret == 0 && pdev == NULL) {
-		ret = 2;
+		ret = 4;
 	} else if (ret == 0) {
 		switch ((pdev->class >> 16) & 0xff) {
 		case PCI_BASE_CLASS_STORAGE:
@@ -367,7 +367,7 @@ static int __init schizo_ino_to_pil(struct pci_dev *pdev, unsigned int ino)
 			break;
 
 		default:
-			ret = 2;
+			ret = 4;
 			break;
 		};
 	}

arch/sparc64/kernel/rtrap.S

@@ -15,7 +15,6 @@
 #include <asm/visasm.h>
 #include <asm/processor.h>
 
-#define		PTREGS_OFF		(STACK_BIAS + REGWIN_SZ)
 #define		RTRAP_PSTATE		(PSTATE_RMO|PSTATE_PEF|PSTATE_PRIV|PSTATE_IE)
 #define		RTRAP_PSTATE_IRQOFF	(PSTATE_RMO|PSTATE_PEF|PSTATE_PRIV)
 #define		RTRAP_PSTATE_AG_IRQOFF	(PSTATE_RMO|PSTATE_PEF|PSTATE_PRIV|PSTATE_AG)
@@ -150,7 +149,7 @@ __handle_signal:
 		 andn			%l1, %l4, %l1
 
 		.align			64
-		.globl			rtrap_irq, rtrap_clr_l6, rtrap, irqsz_patchme
+		.globl			rtrap_irq, rtrap_clr_l6, rtrap, irqsz_patchme, rtrap_xcall
 rtrap_irq:
 #ifdef CONFIG_PREEMPT
 		ldsw			[%g6 + TI_PRE_COUNT], %l0
@@ -165,9 +164,11 @@ irqsz_patchme:	sllx			%l0, 0, %l0
 		lduw			[%l2 + %l0], %l1	! softirq_pending
 		cmp			%l1, 0
 
+		/* mm/ultra.S:xcall_report_regs KNOWS about this load. */
 		bne,pn			%icc, __handle_softirq
 		 ldx			[%sp + PTREGS_OFF + PT_V9_TSTATE], %l1
 __handle_softirq_continue:
+rtrap_xcall:
 		sethi			%hi(0xf << 20), %l4
 		andcc			%l1, TSTATE_PRIV, %l3
 		and			%l1, %l4, %l4
@@ -331,5 +332,3 @@ kern_fpucheck:	ldub			[%g6 + TI_FPDEPTH], %l5
 		wr			%g0, FPRS_DU, %fprs
 		ba,pt			%xcc, rt_continue
 		 stb			%l5, [%g6 + TI_FPDEPTH]
-
-#undef PTREGS_OFF

arch/sparc64/kernel/sbus.c

@@ -628,11 +628,11 @@ void sbus_set_sbus64(struct sbus_dev *sdev, int bursts)
 
 /* SBUS SYSIO INO number to Sparc PIL level. */
 static unsigned char sysio_ino_to_pil[] = {
-	0, 2, 2, 7, 5, 7, 8, 9,		/* SBUS slot 0 */
-	0, 2, 2, 7, 5, 7, 8, 9,		/* SBUS slot 1 */
-	0, 2, 2, 7, 5, 7, 8, 9,		/* SBUS slot 2 */
-	0, 2, 2, 7, 5, 7, 8, 9,		/* SBUS slot 3 */
-	3, /* Onboard SCSI */
+	0, 4, 4, 7, 5, 7, 8, 9,		/* SBUS slot 0 */
+	0, 4, 4, 7, 5, 7, 8, 9,		/* SBUS slot 1 */
+	0, 4, 4, 7, 5, 7, 8, 9,		/* SBUS slot 2 */
+	0, 4, 4, 7, 5, 7, 8, 9,		/* SBUS slot 3 */
+	4, /* Onboard SCSI */
 	5, /* Onboard Ethernet */
 /*XXX*/	8, /* Onboard BPP */
 	0, /* Bogon */

arch/sparc64/kernel/smp.c

@@ -594,11 +594,12 @@ int smp_call_function(void (*func)(void *info), void *info,
 	return 0;
 }
 
-void smp_call_function_client(void)
+void smp_call_function_client(int irq, struct pt_regs *regs)
 {
 	void (*func) (void *info) = call_data->func;
 	void *info = call_data->info;
 
+	clear_softint(1 << irq);
 	if (call_data->wait) {
 		/* let initiator proceed only after completion */
 		func(info);
@@ -722,6 +723,12 @@ void smp_receive_signal(int cpu)
 	}
 }
 
+void smp_receive_signal_client(int irq, struct pt_regs *regs)
+{
+	/* Just return, rtrap takes care of the rest. */
+	clear_softint(1 << irq);
+}
+
 void smp_report_regs(void)
 {
 	smp_cross_call(&xcall_report_regs, 0, 0, 0);
@@ -940,10 +947,14 @@ void smp_release(void)
 extern void prom_world(int);
 extern void save_alternate_globals(unsigned long *);
 extern void restore_alternate_globals(unsigned long *);
-void smp_penguin_jailcell(void)
+void smp_penguin_jailcell(int irq, struct pt_regs *regs)
 {
 	unsigned long global_save[24];
 
+	clear_softint(1 << irq);
+
+	preempt_disable();
+
 	__asm__ __volatile__("flushw");
 	save_alternate_globals(global_save);
 	prom_world(1);
@@ -954,6 +965,8 @@ void smp_penguin_jailcell(void)
 	restore_alternate_globals(global_save);
 	atomic_dec(&smp_capture_registry);
 	prom_world(0);
+
+	preempt_enable();
 }
 
 extern unsigned long xcall_promstop;

arch/sparc64/kernel/time.c

@@ -405,6 +405,7 @@ void __init clock_probe(void)
 	char model[128];
 	int node, busnd = -1, err;
 	unsigned long flags;
+	struct linux_central *cbus;
 #ifdef CONFIG_PCI
 	struct linux_ebus *ebus = NULL;
 	struct isa_bridge *isa_br = NULL;
@@ -431,21 +432,30 @@ void __init clock_probe(void)
 
 	__save_and_cli(flags);
 
-	if(central_bus != NULL) {
+	cbus = central_bus;
+	if (cbus != NULL)
 		busnd = central_bus->child->prom_node;
-	}
+
+	/* Check FHC Central then EBUSs then ISA bridges then SBUSs.
+	 * That way we handle the presence of multiple properly.
+	 *
+	 * As a special case, machines with Central must provide the
+	 * timer chip there.
+	 */
 #ifdef CONFIG_PCI
-	else if (ebus_chain != NULL) {
+	if (ebus_chain != NULL) {
 		ebus = ebus_chain;
+		if (busnd == -1)
 			busnd = ebus->prom_node;
-	} else if (isa_chain != NULL) {
+	}
+	if (isa_chain != NULL) {
 		isa_br = isa_chain;
+		if (busnd == -1)
 			busnd = isa_br->prom_node;
 	}
 #endif
-	else if (sbus_root != NULL) {
+	if (sbus_root != NULL && busnd == -1)
 		busnd = sbus_root->prom_node;
-	}
 
 	if (busnd == -1) {
 		prom_printf("clock_probe: problem, cannot find bus to search.\n");
@@ -464,7 +474,12 @@ void __init clock_probe(void)
 		    strcmp(model, "mk48t59") &&
 		    strcmp(model, "m5819") &&
 		    strcmp(model, "ds1287")) {
-		   	if (node)
+			if (cbus != NULL) {
+				prom_printf("clock_probe: Central bus lacks timer chip.\n");
+				prom_halt();
+			}
+
+		   	if (node != 0)
 				node = prom_getsibling(node);
 #ifdef CONFIG_PCI
 			while ((node == 0) && ebus != NULL) {
@@ -496,12 +511,12 @@ void __init clock_probe(void)
 			prom_halt();
 		}
 
-		if(central_bus) {
+		if (cbus != NULL) {
 			apply_fhc_ranges(central_bus->child, clk_reg, 1);
 			apply_central_ranges(central_bus, clk_reg, 1);
 		}
 #ifdef CONFIG_PCI
-		else if (ebus_chain != NULL) {
+		else if (ebus != NULL) {
 			struct linux_ebus_device *edev;
 
 			for_each_ebusdev(edev, ebus)
@@ -523,7 +538,8 @@ void __init clock_probe(void)
 				mstk48t02_regs = mstk48t59_regs + MOSTEK_48T59_48T02;
 			}
 			break;
-		} else if (isa_chain != NULL) {
+		}
+		else if (isa_br != NULL) {
 			struct isa_device *isadev;
 
 try_isa_clock:

arch/sparc64/kernel/ttable.S

@@ -44,9 +44,16 @@ tl0_stdfmna:	TRAP_NOSAVE(do_stdfmna)
 tl0_privact:	TRAP_NOSAVE(__do_privact)
 tl0_resv038:	BTRAP(0x38) BTRAP(0x39) BTRAP(0x3a) BTRAP(0x3b) BTRAP(0x3c) BTRAP(0x3d)
 tl0_resv03e:	BTRAP(0x3e) BTRAP(0x3f) BTRAP(0x40)
+#ifdef CONFIG_SMP
+tl0_irq1:	TRAP_IRQ(smp_call_function_client, 1)
+tl0_irq2:	TRAP_IRQ(smp_receive_signal_client, 2)
+tl0_irq3:	TRAP_IRQ(smp_penguin_jailcell, 3)
+#else
 tl0_irq1:	BTRAP(0x41)
-tl0_irq2:	TRAP_IRQ(handler_irq, 2)
-tl0_irq3:	TRAP_IRQ(handler_irq, 3)  TRAP_IRQ(handler_irq, 4)
+tl0_irq2:	BTRAP(0x42)
+tl0_irq3:	BTRAP(0x43)
+#endif
+tl0_irq4:	TRAP_IRQ(handler_irq, 4)
 tl0_irq5:	TRAP_IRQ(handler_irq, 5)  TRAP_IRQ(handler_irq, 6)
 tl0_irq7:	TRAP_IRQ(handler_irq, 7)  TRAP_IRQ(handler_irq, 8)
 tl0_irq9:	TRAP_IRQ(handler_irq, 9)  TRAP_IRQ(handler_irq, 10)

arch/sparc64/mm/ultra.S

@@ -11,6 +11,7 @@
 #include <asm/spitfire.h>
 #include <asm/mmu_context.h>
 #include <asm/pil.h>
+#include <asm/head.h>
 
 	/* Basically, all this madness has to do with the
 	 * fact that Cheetah does not support IMMU flushes
@@ -482,6 +483,15 @@ xcall_flush_tlb_range:
 	nop
 	nop
 
+	/* NOTE: This is SPECIAL!!  We do etrap/rtrap however
+	 *       we choose to deal with the "BH's run with
+	 *       %pil==15" problem (described in asm/pil.h)
+	 *       by just invoking rtrap directly past where
+	 *       BH's are checked for.
+	 *
+	 *       We do it like this because we do not want %pil==15
+	 *       lockups to prevent regs being reported.
+	 */
 	.globl		xcall_report_regs
 xcall_report_regs:
 	rdpr		%pstate, %g2
@@ -489,12 +499,14 @@ xcall_report_regs:
 	rdpr		%pil, %g2
 	wrpr		%g0, 15, %pil
 	sethi		%hi(109f), %g7
-	b,pt		%xcc, etrap_irq
+	b,pt		%xcc, etrap
 109:	 or		%g7, %lo(109b), %g7
 	call		__show_regs
 	 add		%sp, STACK_BIAS + REGWIN_SZ, %o0
-	b,pt		%xcc, rtrap_irq
-	 nop
+	clr		%l6
+	/* Has to be a non-v9 branch due to the large distance. */
+	b		rtrap_xcall
+	 ldx		[%sp + PTREGS_OFF + PT_V9_TSTATE], %l1
 
 	.align		32
 	.globl		xcall_flush_dcache_page_cheetah
@@ -543,20 +555,6 @@ xcall_flush_dcache_page_spitfire: /* %g1 == physical page address
 	nop
 	nop
 
-	.globl		xcall_capture
-xcall_capture:
-	rdpr		%pstate, %g2
-	wrpr		%g2, PSTATE_IG | PSTATE_AG, %pstate
-	rdpr		%pil, %g2
-	wrpr		%g0, 15, %pil
-	sethi		%hi(109f), %g7
-	b,pt		%xcc, etrap_irq
-109:	 or		%g7, %lo(109b), %g7
-	call		smp_penguin_jailcell
-	 nop
-	b,pt		%xcc, rtrap_irq
-	 nop
-
 	.globl		xcall_promstop
 xcall_promstop:
 	rdpr		%pstate, %g2
@@ -564,7 +562,7 @@ xcall_promstop:
 	rdpr		%pil, %g2
 	wrpr		%g0, 15, %pil
 	sethi		%hi(109f), %g7
-	b,pt		%xcc, etrap_irq
+	b,pt		%xcc, etrap
 109:	 or		%g7, %lo(109b), %g7
 	flushw
 	call		prom_stopself
@@ -573,21 +571,6 @@ xcall_promstop:
 1:	b,a,pt		%xcc, 1b
 	nop
 
-	.globl		xcall_receive_signal
-xcall_receive_signal:
-	rdpr		%pstate, %g2
-	wrpr		%g2, PSTATE_IG | PSTATE_AG, %pstate
-	rdpr		%tstate, %g1
-	andcc		%g1, TSTATE_PRIV, %g0
-	/* If we did not trap from user space, just ignore. */
-	bne,pn		%xcc, 99f
-	 sethi		%hi(109f), %g7
-	b,pt		%xcc, etrap
-109:	 or		%g7, %lo(109b), %g7
-	b,pt		%xcc, rtrap
-	 clr		%l6
-99:	retry
-
 	.data
 
 errata32_hwbug:
@@ -670,18 +653,20 @@ __spitfire_xcall_flush_cache_all:
 __cheetah_xcall_flush_cache_all:
 	retry
 
+	/* These just get rescheduled to PIL vectors. */
 	.globl		xcall_call_function
 xcall_call_function:
-	rdpr		%pstate, %g2
-	wrpr		%g2, PSTATE_IG | PSTATE_AG, %pstate
-	rdpr		%pil, %g2
-	wrpr		%g0, 15, %pil
-	sethi		%hi(109f), %g7
-	b,pt		%xcc, etrap_irq
-109:	 or		%g7, %lo(109b), %g7
-	call		smp_call_function_client
-	 nop
-	b,pt		%xcc, rtrap_irq
-	 nop
+	wr		%g0, (1 << PIL_SMP_CALL_FUNC), %set_softint
+	retry
+
+	.globl		xcall_receive_signal
+xcall_receive_signal:
+	wr		%g0, (1 << PIL_SMP_RECEIVE_SIGNAL), %set_softint
+	retry
+
+	.globl		xcall_capture
+xcall_capture:
+	wr		%g0, (1 << PIL_SMP_CAPTURE), %set_softint
+	retry
 
 #endif /* CONFIG_SMP */

include/asm-sparc64/fhc.h

@@ -86,10 +86,10 @@ struct fhc_regs {
 #define  FHC_BSR_NIA		0x0000001c /* Jumper, bit 18 in PROM space       */
 #define  FHC_BSR_SI		0x00000001 /* Spare input pin value              */
 #define FHC_PREGS_ECC	0x40UL	/* FHC ECC Control Register (16 bits) */
-#define FHC_PREGS_JCTRL	0x50UL	/* FHC JTAG Control Register */
+#define FHC_PREGS_JCTRL	0xf0UL	/* FHC JTAG Control Register */
 #define  FHC_JTAG_CTRL_MENAB	0x80000000 /* Indicates this is JTAG Master	 */
 #define  FHC_JTAG_CTRL_MNONE	0x40000000 /* Indicates no JTAG Master present	 */
-#define FHC_PREGS_JCMD	0x60UL	/* FHC JTAG Command Register */
+#define FHC_PREGS_JCMD	0x100UL	/* FHC JTAG Command Register */
 	unsigned long			ireg;	/* FHC IGN reg */
 #define FHC_IREG_IGN	0x00UL	/* This FHC's IGN */
 	unsigned long			ffregs;	/* FHC fanfail regs */

include/asm-sparc64/head.h

@@ -6,4 +6,6 @@
 
 #define KERNBASE	0x400000
 
+#define	PTREGS_OFF	(STACK_BIAS + REGWIN_SZ)
+
 #endif /* !(_SPARC64_HEAD_H) */

include/asm-sparc64/pil.h

@@ -3,20 +3,24 @@
 #define _SPARC64_PIL_H
 
 /* To avoid some locking problems, we hard allocate certain PILs
- * for SMP cross call messages.  cli() does not block the cross
- * call delivery, so when SMP locking is an issue we reschedule
- * the event into a PIL interrupt which is blocked by cli().
+ * for SMP cross call messages that must do a etrap/rtrap.
  *
- * XXX In fact the whole set of PILs used for hardware interrupts
- * XXX may be allocated in this manner.  All of the devices can
- * XXX happily sit at the same PIL.  We would then need only two
- * XXX PILs, one for devices and one for the CPU local timer tick.
+ * A cli() does not block the cross call delivery, so when SMP
+ * locking is an issue we reschedule the event into a PIL interrupt
+ * which is blocked by cli().
+ *
+ * In fact any XCALL which has to etrap/rtrap has a problem because
+ * it is difficult to prevent rtrap from running BH's, and that would
+ * need to be done if the XCALL arrived while %pil==15.
  */
-/* None currently allocated, '1' is available for use. */
-#define PIL_SMP_1	1
+#define PIL_SMP_CALL_FUNC	1
+#define PIL_SMP_RECEIVE_SIGNAL	2
+#define PIL_SMP_CAPTURE		3
 
 #ifndef __ASSEMBLY__
-#define PIL_RESERVED(PIL)	((PIL) == PIL_SMP_1)
+#define PIL_RESERVED(PIL)	((PIL) == PIL_SMP_CALL_FUNC || \
+				 (PIL) == PIL_SMP_RECEIVE_SIGNAL || \
+				 (PIL) == PIL_SMP_CAPTURE)
 #endif
 
 #endif /* !(_SPARC64_PIL_H) */