Commit 59a2e53b authored by Yaniv Rosner's avatar Yaniv Rosner Committed by David S. Miller

bnx2x: Fix link issue for BCM8727 boards.

This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: default avatarYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: default avatarEilon Greenstein <eilong@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 9379c9be
......@@ -8089,6 +8089,8 @@ static int bnx2x_verify_sfp_module(struct bnx2x_phy *phy,
netdev_err(bp->dev, "Warning: Unqualified SFP+ module detected,"
" Port %d from %s part number %s\n",
params->port, vendor_name, vendor_pn);
if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) !=
PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_WARNING_MSG)
phy->flags |= FLAGS_SFP_NOT_APPROVED;
return -EINVAL;
}
......@@ -9149,6 +9151,12 @@ static int bnx2x_8727_config_init(struct bnx2x_phy *phy,
tmp2 &= 0xFFEF;
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, tmp2);
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER,
&tmp2);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER,
(tmp2 & 0x7fff));
}
return 0;
......@@ -9329,12 +9337,11 @@ static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy,
MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL,
((1<<5) | (1<<2)));
}
DP(NETIF_MSG_LINK, "Enabling 8727 TX laser if SFP is approved\n");
bnx2x_8727_specific_func(phy, params, ENABLE_TX);
/* If transmitter is disabled, ignore false link up indication */
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &val1);
if (val1 & (1<<15)) {
if (!(phy->flags & FLAGS_SFP_NOT_APPROVED)) {
DP(NETIF_MSG_LINK, "Enabling 8727 TX laser\n");
bnx2x_sfp_set_transmitter(params, phy, 1);
} else {
DP(NETIF_MSG_LINK, "Tx is disabled\n");
return 0;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment