Commit 5e3bf9c5 authored by Chunfeng Yun's avatar Chunfeng Yun Committed by Kishon Vijay Abraham I

dt-bindings: phy-mt65xx-usb: add support for new version phy

add a new compatible string for "mt2712", and move reference clock
into each port node;
Signed-off-by: default avatarChunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarKishon Vijay Abraham I <kishon@ti.com>
parent c0250fe5
......@@ -6,12 +6,11 @@ This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
Required properties (controller (parent) node):
- compatible : should be one of
"mediatek,mt2701-u3phy"
"mediatek,mt2712-u3phy"
"mediatek,mt8173-u3phy"
- reg : offset and length of register for phy, exclude port's
register.
- clocks : a list of phandle + clock-specifier pairs, one for each
entry in clock-names
- clock-names : must contain
- clocks : (deprecated, use port's clocks instead) a list of phandle +
clock-specifier pairs, one for each entry in clock-names
- clock-names : (deprecated, use port's one instead) must contain
"u3phya_ref": for reference clock of usb3.0 analog phy.
Required nodes : a sub-node is required for each port the controller
......@@ -19,8 +18,19 @@ Required nodes : a sub-node is required for each port the controller
'reg' property is used inside these nodes to describe
the controller's topology.
Optional properties (controller (parent) node):
- reg : offset and length of register shared by multiple ports,
exclude port's private register. It is needed on mt2701
and mt8173, but not on mt2712.
Required properties (port (child) node):
- reg : address and length of the register set for the port.
- clocks : a list of phandle + clock-specifier pairs, one for each
entry in clock-names
- clock-names : must contain
"ref": 48M reference clock for HighSpeed analog phy; and 26M
reference clock for SuperSpeed analog phy, sometimes is
24M, 25M or 27M, depended on platform.
- #phy-cells : should be 1 (See second example)
cell after port phandle is phy type from:
- PHY_TYPE_USB2
......@@ -31,21 +41,31 @@ Example:
u3phy: usb-phy@11290000 {
compatible = "mediatek,mt8173-u3phy";
reg = <0 0x11290000 0 0x800>;
clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
clock-names = "u3phya_ref";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "okay";
phy_port0: port@11290800 {
reg = <0 0x11290800 0 0x800>;
u2port0: usb-phy@11290800 {
reg = <0 0x11290800 0 0x100>;
clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
u3port0: usb-phy@11290900 {
reg = <0 0x11290800 0 0x700>;
clocks = <&clk26m>;
clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
phy_port1: port@11291000 {
reg = <0 0x11291000 0 0x800>;
u2port1: usb-phy@11291000 {
reg = <0 0x11291000 0 0x100>;
clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
......@@ -64,7 +84,54 @@ Example:
usb30: usb@11270000 {
...
phys = <&phy_port0 PHY_TYPE_USB3>;
phy-names = "usb3-0";
phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
phy-names = "usb2-0", "usb3-0";
...
};
Layout differences of banks between mt8173/mt2701 and mt2712
-------------------------------------------------------------
mt8173 and mt2701:
port offset bank
shared 0x0000 SPLLC
0x0100 FMREG
u2 port0 0x0800 U2PHY_COM
u3 port0 0x0900 U3PHYD
0x0a00 U3PHYD_BANK2
0x0b00 U3PHYA
0x0c00 U3PHYA_DA
u2 port1 0x1000 U2PHY_COM
u3 port1 0x1100 U3PHYD
0x1200 U3PHYD_BANK2
0x1300 U3PHYA
0x1400 U3PHYA_DA
u2 port2 0x1800 U2PHY_COM
...
mt2712:
port offset bank
u2 port0 0x0000 MISC
0x0100 FMREG
0x0300 U2PHY_COM
u3 port0 0x0700 SPLLC
0x0800 CHIP
0x0900 U3PHYD
0x0a00 U3PHYD_BANK2
0x0b00 U3PHYA
0x0c00 U3PHYA_DA
u2 port1 0x1000 MISC
0x1100 FMREG
0x1300 U2PHY_COM
u3 port1 0x1700 SPLLC
0x1800 CHIP
0x1900 U3PHYD
0x1a00 U3PHYD_BANK2
0x1b00 U3PHYA
0x1c00 U3PHYA_DA
u2 port2 0x2000 MISC
...
SPLLC shared by u3 ports and FMREG shared by u2 ports on
mt8173/mt2701 are put back into each port; a new bank MISC for
u2 ports and CHIP for u3 ports are added on mt2712.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment