Blackfin: cm-bf537u: split board from cm-bf537e

The cm-bf537u module, while similar to the cm-bf537e, is different enough
to warrant its own resources.  It has a USB controller but no PHY.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

arch/blackfin/Kconfig

@@ -342,8 +342,9 @@ config MEM_MT48LC64M4A2FB_7E
 config MEM_MT48LC16M16A2TG_75
 	bool
 	depends on (BFIN533_EZKIT || BFIN561_EZKIT \
-		|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
-		|| H8606_HVSISTEMAS || BFIN527_BLUETECHNIX_CM)
+		|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM_E \
+		|| BFIN537_BLUETECHNIX_CM_U || H8606_HVSISTEMAS \
+		|| BFIN527_BLUETECHNIX_CM)
 	default y
 
 config MEM_MT48LC32M8A2_75
@@ -459,7 +460,7 @@ config VCO_MULT
 	default "45" if BFIN533_STAMP
 	default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT)
 	default "22" if BFIN533_BLUETECHNIX_CM
-	default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
+	default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
 	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
 	help

arch/blackfin/mach-bf537/boards/Kconfig

@@ -9,11 +9,17 @@ config BFIN537_STAMP
 	help
 	  BF537-STAMP board support.
 
-config BFIN537_BLUETECHNIX_CM
-	bool "Bluetechnix CM-BF537"
+config BFIN537_BLUETECHNIX_CM_E
+	bool "Bluetechnix CM-BF537E"
 	depends on (BF537)
 	help
-	  CM-BF537 support for EVAL- and DEV-Board.
+	  CM-BF537E support for EVAL- and DEV-Board.
+
+config BFIN537_BLUETECHNIX_CM_U
+	bool "Bluetechnix CM-BF537U"
+	depends on (BF537)
+	help
+	  CM-BF537U support for EVAL- and DEV-Board.
 
 config BFIN537_BLUETECHNIX_TCM
 	bool "Bluetechnix TCM-BF537"

arch/blackfin/mach-bf537/boards/Makefile

@@ -3,7 +3,8 @@
 #
 
 obj-$(CONFIG_BFIN537_STAMP)            += stamp.o
-obj-$(CONFIG_BFIN537_BLUETECHNIX_CM)   += cm_bf537.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_E) += cm_bf537e.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_U) += cm_bf537u.o
 obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM)  += tcm_bf537.o
 obj-$(CONFIG_PNAV10)                   += pnav10.o
 obj-$(CONFIG_CAMSIG_MINOTAUR)          += minotaur.o

arch/blackfin/mach-bf537/boards/cm_bf537e.c

+/*
+ * File:         arch/blackfin/mach-bf537/boards/cm_bf537.c
+ * Based on:     arch/blackfin/mach-bf533/boards/ezkit.c
+ * Author:       Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:      2005
+ * Description:  Board description file
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb/isp1362.h>
+#endif
+#include <linux/ata_platform.h>
+#include <linux/irq.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "Bluetechnix CM BF537E";
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00020000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = 0xe0000,
+		.offset = 0x20000
+	}, {
+		.name = "file system(spi)",
+		.size = 0x700000,
+		.offset = 0x00100000,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+	{
+		.modalias = "ad1836",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+	{
+		.modalias = "mmc_spi",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &mmc_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI,
+		.end   = IRQ_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+static struct platform_device hitachi_fb_device = {
+	.name = "hitachi-tx09",
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91x_resources[] = {
+	{
+		.start = 0x20200300,
+		.end = 0x20200300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF14,
+		.end = IRQ_PF14,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		},
+};
+
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+	{
+		.start = 0x20308000,
+		.end = 0x20308000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20308004,
+		.end = 0x20308004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PG15,
+		.end = IRQ_PG15,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+	.sel15Kres = 1,
+	.clknotstop = 0,
+	.oc_enable = 0,
+	.int_act_high = 0,
+	.int_edge_triggered = 0,
+	.remote_wakeup_connected = 0,
+	.no_power_switching = 1,
+	.power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+	.name = "isp1362-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &isp1362_priv,
+	},
+	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+	.resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PG13,
+		.end = IRQ_PG13,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+	.start = 0,
+	.end   = MAX_BLACKFIN_GPIOS - 1,
+	.flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+	.name = "simple-gpio",
+	.id = -1,
+	.num_resources = 1,
+	.resource = &bfin_gpios_resources,
+};
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+	{
+		.name   = "bootloader(nor)",
+		.size   = 0x40000,
+		.offset = 0,
+	}, {
+		.name   = "linux kernel(nor)",
+		.size   = 0x100000,
+		.offset = MTDPART_OFS_APPEND,
+	}, {
+		.name   = "file system(nor)",
+		.size   = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data cm_flash_data = {
+	.width    = 2,
+	.parts    = cm_partitions,
+	.nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PF4 };
+
+static struct resource cm_flash_resource[] = {
+	{
+		.name  = "cfi_probe",
+		.start = 0x20000000,
+		.end   = 0x201fffff,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = (unsigned long)cm_flash_gpios,
+		.end   = ARRAY_SIZE(cm_flash_gpios),
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device cm_flash_device = {
+	.name          = "gpio-addr-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &cm_flash_data,
+	},
+	.num_resources = ARRAY_SIZE(cm_flash_resource),
+	.resource      = cm_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART0_ERROR,
+		.end = IRQ_UART0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_TX,
+		.end = CH_UART0_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX,
+		.flags = IORESOURCE_DMA,
+	},
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart0_device = {
+	.name = "bfin-uart",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_uart0_resources),
+	.resource = bfin_uart0_resources,
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART1_ERROR,
+		.end = IRQ_UART1_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_TX,
+		.end = CH_UART1_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX,
+		.flags = IORESOURCE_DMA,
+	},
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart1_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart1_resources),
+	.resource = bfin_uart1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+static struct platform_device bfin_sir0_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
+	.resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+static struct platform_device bfin_sir1_device = {
+	.name = "bfin_sir",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
+	.resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+	.name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+	.dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT	IRQ_PF14
+
+static struct pata_platform_info bfin_pata_platform_data = {
+	.ioport_shift = 2,
+	.irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+	{
+		.start = 0x2030C000,
+		.end = 0x2030C01F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = 0x2030D018,
+		.end = 0x2030D01B,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = PATA_INT,
+		.end = PATA_INT,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pata_device = {
+	.name = "pata_platform",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pata_resources),
+	.resource = bfin_pata_resources,
+	.dev = {
+		.platform_data = &bfin_pata_platform_data,
+	}
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+	VRPAIR(VLEV_085, 250000000),
+	VRPAIR(VLEV_090, 376000000),
+	VRPAIR(VLEV_095, 426000000),
+	VRPAIR(VLEV_100, 426000000),
+	VRPAIR(VLEV_105, 476000000),
+	VRPAIR(VLEV_110, 476000000),
+	VRPAIR(VLEV_115, 476000000),
+	VRPAIR(VLEV_120, 500000000),
+	VRPAIR(VLEV_125, 533000000),
+	VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+static struct platform_device *cm_bf537e_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+	&hitachi_fb_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	&bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	&bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+	&bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	&bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+	&isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mii_bus,
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	&bfin_pata_device,
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+	&cm_flash_device,
+#endif
+
+	&bfin_gpios_device,
+};
+
+static int __init cm_bf537e_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+	platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+	return 0;
+}
+
+arch_initcall(cm_bf537e_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+	random_ether_addr(addr);
+	printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);

arch/blackfin/mach-bf537/boards/cm_bf537.c → arch/blackfin/mach-bf537/boards/cm_bf537u.c

 /*
- * File:         arch/blackfin/mach-bf537/boards/cm_bf537.c
+ * File:         arch/blackfin/mach-bf537/boards/cm_bf537u.c
  * Based on:     arch/blackfin/mach-bf533/boards/ezkit.c
  * Author:       Aidan Williams <aidan@nicta.com.au>
  *
@@ -45,11 +45,12 @@
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
+#include <linux/spi/mmc_spi.h>
 
 /*
  * Name the Board for the /proc/cpuinfo
  */
-const char bfin_board_name[] = "Bluetechnix CM BF537";
+const char bfin_board_name[] = "Bluetechnix CM BF537U";
 
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 /* all SPI peripherals info goes here */
@@ -318,7 +319,7 @@ static struct mtd_partition cm_partitions[] = {
 		.offset = 0,
 	}, {
 		.name   = "linux kernel(nor)",
-		.size   = 0xE0000,
+		.size   = 0x100000,
 		.offset = MTDPART_OFS_APPEND,
 	}, {
 		.name   = "file system(nor)",
@@ -333,7 +334,7 @@ static struct physmap_flash_data cm_flash_data = {
 	.nr_parts = ARRAY_SIZE(cm_partitions),
 };
 
-static unsigned cm_flash_gpios[] = { GPIO_PF4 };
+static unsigned cm_flash_gpios[] = { GPIO_PH0 };
 
 static struct resource cm_flash_resource[] = {
 	{
@@ -542,7 +543,7 @@ static struct platform_device bfin_dpmc = {
 	},
 };
 
-static struct platform_device *cm_bf537_devices[] __initdata = {
+static struct platform_device *cm_bf537u_devices[] __initdata = {
 
 	&bfin_dpmc,
 
@@ -608,10 +609,10 @@ static struct platform_device *cm_bf537_devices[] __initdata = {
 	&bfin_gpios_device,
 };
 
-static int __init cm_bf537_init(void)
+static int __init cm_bf537u_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
-	platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices));
+	platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif
@@ -622,7 +623,7 @@ static int __init cm_bf537_init(void)
 	return 0;
 }
 
-arch_initcall(cm_bf537_init);
+arch_initcall(cm_bf537u_init);
 
 void bfin_get_ether_addr(char *addr)
 {