Commit 62c83cde authored by Jim Cromie's avatar Jim Cromie Committed by Linus Torvalds

[PATCH] chardev: GPIO for SCx200 & PC-8736x: whitespace pre-clean

GPIO SUPPORT FOR SCx200 & PC8736x

The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips.  Its handy for the Soekris.com net-4801, which has both chips.

These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it.  His feedback has
been incorporated.  Thanks Jesper !

Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far.  Theyre mostly BSD folk over there, but we'll
see..

Device-file & Sysfs

The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call.  Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.

Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.

I've recently bolted on a proto sysfs interface for both new drivers.  Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed.  Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.

The driver-split

The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.

The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.

The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable.  Driver specific open()s set private_data to the vtable so its
available for use by write().

The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface.  To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.

heres how the pins are presented in syslog:

[ 1890.176223]  scx200_gpio.0: io00: 0x0044 TS OD PUE  EDGE LO DEBOUNCE
[ 1890.287223]  scx200_gpio.0: io01: 0x0003 OE PP PUD  EDGE LO

nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.

scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable).  A driver-spcific open() initializes filp->private_data with the
vtable.

Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.

Heres a working overview of the patchset:

# series file for GPIO

# Spring Cleaning
gpio-scx/patch.preclean        # scripts/Lindent fixes, editor-ctrl comments

# API Modernization

gpio-scx/patch.api26        # what I learned from LDD3
gpio-scx/patch.platform-dev-2    # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor    # fix to match std practice

# Debuggability

gpio-scx/patch.dump-diet    # shrink gpio_dump()
gpio-scx/patch.viewpins        # add new 'command' to call dump()
gpio-scx/patch.init-refactor    # pull shadow-register init to sub

# Access-Abstraction (add vtable)

gpio-scx/patch.access-vtable    # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls    # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell    # add empty driver for common-fops

# move code under abstraction
gpio-scx/patch.migrate-fops    # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump    # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio    # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG    # enable all dev_dbg()s

# Cleanups

# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x    # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio    # add device to 'vtable', use in dev_dbg()

# gpio-scx/patch.pin-config-view    # another 'c' 'command'
# gpio-scx/quiet-getset        # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current    # imitate scx200_gpio's shadow regs in
pc87*

# post KMentors-post patches ..

gpio-scx/patch.mutexes        # use mutexes for config-locks
gpio-scx/patch.viewpins-values    # extend dump to obsolete separate 'c' cmd

gpio-scx/patch.kconfig        # add stuff for kbuild

# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.

diff.sys-gpio-rollup-1

This patch:

Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: default avatarJim Cromie <jim.cromie@gmail.com>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent 5a67e4c5
......@@ -159,10 +159,3 @@ EXPORT_SYMBOL(scx200_gpio_base);
EXPORT_SYMBOL(scx200_gpio_shadow);
EXPORT_SYMBOL(scx200_gpio_configure);
EXPORT_SYMBOL(scx200_cb_base);
/*
Local variables:
compile-command: "make -k -C ../../.. SUBDIRS=arch/i386/kernel modules"
c-basic-offset: 8
End:
*/
......@@ -34,10 +34,9 @@ static ssize_t scx200_gpio_write(struct file *file, const char __user *data,
for (i = 0; i < len; ++i) {
char c;
if (get_user(c, data+i))
if (get_user(c, data + i))
return -EFAULT;
switch (c)
{
switch (c) {
case '0':
scx200_gpio_set(m, 0);
break;
......@@ -140,10 +139,3 @@ static void __exit scx200_gpio_cleanup(void)
module_init(scx200_gpio_init);
module_exit(scx200_gpio_cleanup);
/*
Local variables:
compile-command: "make -k -C ../.. SUBDIRS=drivers/char modules"
c-basic-offset: 8
End:
*/
......@@ -49,10 +49,3 @@ extern unsigned scx200_cb_base;
#define SCx200_REV 0x3d /* Revision Register */
#define SCx200_CBA 0x3e /* Configuration Base Address Register */
#define SCx200_CBA_SCRATCH 0x64 /* Configuration Base Address Scratchpad */
/*
Local variables:
compile-command: "make -C ../.. bzImage modules"
c-basic-offset: 8
End:
*/
......@@ -87,10 +87,3 @@ static inline void scx200_gpio_change(int index) {
#undef __SCx200_GPIO_SHADOW
#undef __SCx200_GPIO_INDEX
#undef __SCx200_GPIO_OUT
/*
Local variables:
compile-command: "make -C ../.. bzImage modules"
c-basic-offset: 8
End:
*/
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment