Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix port 0 mac address for mips mv6434x platforms
  [SERIAL] serial_txx9 driver update
  Revert "[PATCH] Generic ioremap_page_range: mips conversion"
  [MIPS] Cobalt: Rename "Colo" MTD partition to "firmware".
  [MIPS] SMP: Get smp_tune_scheduling to do something useful.
  [MIPS] Add basic SMARTMIPS ASE support

arch/mips/Kconfig

@@ -274,6 +274,7 @@ config MIPS_ATLAS
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_SUPPORTS_MULTITHREADING if EXPERIMENTAL
+	select SYS_SUPPORTS_SMARTMIPS
 	select GENERIC_HARDIRQS_NO__DO_IRQ
 	help
 	  This enables support for the MIPS Technologies Atlas evaluation
@@ -305,6 +306,7 @@ config MIPS_MALTA
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_SUPPORTS_MULTITHREADING
+	select SYS_SUPPORTS_SMARTMIPS
 	help
 	  This enables support for the MIPS Technologies Malta evaluation
 	  board.
@@ -322,6 +324,7 @@ config MIPS_SEAD
 	select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_SMARTMIPS
 	help
 	  This enables support for the MIPS Technologies SEAD evaluation
 	  board.
@@ -1641,6 +1644,18 @@ config 64BIT_PHYS_ADDR
 config CPU_HAS_LLSC
 	bool
 
+config CPU_HAS_SMARTMIPS
+	depends on SYS_SUPPORTS_SMARTMIPS
+	bool "Support for the SmartMIPS ASE"
+	help
+	  SmartMIPS is a extension of the MIPS32 architecture aimed at
+	  increased security at both hardware and software level for
+	  smartcards.  Enabling this option will allow proper use of the
+	  SmartMIPS instructions by Linux applications.  However a kernel with
+	  this option will not work on a MIPS core without SmartMIPS core.  If
+	  you don't know you probably don't have SmartMIPS and should say N
+	  here.
+
 config CPU_HAS_WB
 	bool
 
@@ -1704,6 +1719,9 @@ config CPU_SUPPORTS_HIGHMEM
 config SYS_SUPPORTS_HIGHMEM
 	bool
 
+config SYS_SUPPORTS_SMARTMIPS
+	bool
+
 config ARCH_FLATMEM_ENABLE
 	def_bool y
 	depends on !NUMA

arch/mips/Makefile

@@ -103,6 +103,8 @@ predef-le += -DMIPSEL -D_MIPSEL -D__MIPSEL -D__MIPSEL__
 cflags-$(CONFIG_CPU_BIG_ENDIAN)		+= $(shell $(CC) -dumpmachine |grep -q 'mips.*el-.*' && echo -EB $(undef-all) $(predef-be))
 cflags-$(CONFIG_CPU_LITTLE_ENDIAN)	+= $(shell $(CC) -dumpmachine |grep -q 'mips.*el-.*' || echo -EL $(undef-all) $(predef-le))
 
+cflags-$(CONFIG_CPU_HAS_SMARTMIPS)	+= $(call cc-option,-msmartmips)
+
 cflags-$(CONFIG_SB1XXX_CORELIS)	+= $(call cc-option,-mno-sched-prolog) \
 				   -fno-omit-frame-pointer
 

arch/mips/cobalt/mtd.c

@@ -24,7 +24,7 @@
 
 static struct mtd_partition cobalt_mtd_partitions[] = {
 	{
-		.name	= "Colo",
+		.name	= "firmware",
 		.offset	= 0x0,
 		.size	= 0x80000,
 	},

arch/mips/configs/atlas_defconfig

@@ -139,10 +139,12 @@ CONFIG_MIPS_MT_DISABLED=y
 CONFIG_SYS_SUPPORTS_MULTITHREADING=y
 # CONFIG_64BIT_PHYS_ADDR is not set
 CONFIG_CPU_HAS_LLSC=y
+# CONFIG_CPU_HAS_SMARTMIPS is not set
 CONFIG_CPU_HAS_SYNC=y
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_SYS_SUPPORTS_SMARTMIPS=y
 CONFIG_ARCH_FLATMEM_ENABLE=y
 CONFIG_SELECT_MEMORY_MODEL=y
 CONFIG_FLATMEM_MANUAL=y

arch/mips/configs/bigsur_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:35 2007
+# Tue Feb 20 21:47:22 2007
 #
 CONFIG_MIPS=y
 
@@ -417,6 +417,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -589,6 +590,7 @@ CONFIG_NET_SB1250_MAC=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 # CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1025,7 +1027,6 @@ CONFIG_FORCED_INLINING=y
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
 # CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
 # CONFIG_SB1XXX_CORELIS is not set
 # CONFIG_RUNTIME_DEBUG is not set
 

arch/mips/configs/capcella_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:36 2007
+# Tue Feb 20 21:47:22 2007
 #
 CONFIG_MIPS=y
 
@@ -388,6 +388,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/cobalt_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Mon Feb 19 14:51:58 2007
+# Tue Feb 20 21:47:24 2007
 #
 CONFIG_MIPS=y
 
@@ -425,7 +425,7 @@ CONFIG_MTD_CFI_UTIL=y
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_PHYSMAP_START=0x0
-CONFIG_MTD_PHYSMAP_LEN=0
+CONFIG_MTD_PHYSMAP_LEN=0x0
 CONFIG_MTD_PHYSMAP_BANKWIDTH=0
 # CONFIG_MTD_PLATRAM is not set
 
@@ -449,7 +449,6 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=0
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -464,6 +463,7 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=0
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -658,6 +658,7 @@ CONFIG_TULIP=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=y
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)

arch/mips/configs/db1000_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:39 2007
+# Tue Feb 20 21:47:24 2007
 #
 CONFIG_MIPS=y
 
@@ -548,6 +548,7 @@ CONFIG_MTD_ALCHEMY=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1103,6 +1104,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1100_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:39 2007
+# Tue Feb 20 21:47:24 2007
 #
 CONFIG_MIPS=y
 
@@ -537,6 +537,7 @@ CONFIG_MTD_ALCHEMY=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1103,6 +1104,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1200_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:40 2007
+# Tue Feb 20 21:47:25 2007
 #
 CONFIG_MIPS=y
 
@@ -541,6 +541,7 @@ CONFIG_MTD_NAND_IDS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1185,6 +1186,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="mem=48M"
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1500_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:41 2007
+# Tue Feb 20 21:47:26 2007
 #
 CONFIG_MIPS=y
 
@@ -542,7 +542,6 @@ CONFIG_MTD_ALCHEMY=y
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -557,6 +556,7 @@ CONFIG_MTD_ALCHEMY=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -715,6 +715,7 @@ CONFIG_MIPS_AU1X00_ENET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1145,6 +1146,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set
@@ -1402,6 +1404,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1550_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:42 2007
+# Tue Feb 20 21:47:27 2007
 #
 CONFIG_MIPS=y
 
@@ -562,6 +562,7 @@ CONFIG_MTD_NAND_AU1550=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -751,6 +752,7 @@ CONFIG_MIPS_AU1X00_ENET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1219,6 +1221,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/ddb5477_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:43 2007
+# Tue Feb 20 21:47:28 2007
 #
 CONFIG_MIPS=y
 
@@ -386,6 +386,7 @@ CONFIG_PROC_EVENTS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -925,6 +926,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="ip=any"
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/decstation_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:44 2007
+# Tue Feb 20 21:47:28 2007
 #
 CONFIG_MIPS=y
 
@@ -398,6 +398,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/e55_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:44 2007
+# Tue Feb 20 21:47:28 2007
 #
 CONFIG_MIPS=y
 
@@ -294,6 +294,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # Plug and Play support
 #
 # CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/emma2rh_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:46 2007
+# Tue Feb 20 21:47:29 2007
 #
 CONFIG_MIPS=y
 
@@ -611,7 +611,6 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -626,6 +625,7 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1039,6 +1039,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_ADM1021 is not set
 # CONFIG_SENSORS_ADM1025 is not set
 # CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
 # CONFIG_SENSORS_ADM1031 is not set
 # CONFIG_SENSORS_ADM9240 is not set
 # CONFIG_SENSORS_ASB100 is not set

arch/mips/configs/ev64120_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:46 2007
+# Tue Feb 20 21:47:30 2007
 #
 CONFIG_MIPS=y
 
@@ -391,6 +391,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -520,6 +521,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -914,6 +916,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs rw nfsroot=192.168.1.1:/mnt/disk2/fs.gal ip=192.168.1.211:192.168.1.1:::gt::"
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/excite_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:47 2007
+# Tue Feb 20 21:47:31 2007
 #
 CONFIG_MIPS=y
 
@@ -451,6 +451,7 @@ CONFIG_MTD_NAND_VERIFY_WRITE=y
 # CONFIG_MTD_NAND_ECC_SMC is not set
 CONFIG_MTD_NAND_IDS=y
 # CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_BASLER_EXCITE is not set
 # CONFIG_MTD_NAND_CAFE is not set
 # CONFIG_MTD_NAND_NANDSIM is not set
 
@@ -467,6 +468,7 @@ CONFIG_MTD_NAND_IDS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -638,6 +640,7 @@ CONFIG_NETDEVICES=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1008,6 +1011,7 @@ CONFIG_USB_HID=m
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set
@@ -1277,6 +1281,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/ip22_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:48 2007
+# Tue Feb 20 21:47:32 2007
 #
 CONFIG_MIPS=y
 
@@ -620,6 +620,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/ip27_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:49 2007
+# Tue Feb 20 21:47:32 2007
 #
 CONFIG_MIPS=y
 
@@ -456,6 +456,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -672,6 +673,7 @@ CONFIG_SGI_IOC3_ETH=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1060,6 +1062,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=15
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/ip32_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:50 2007
+# Tue Feb 20 21:47:33 2007
 #
 CONFIG_MIPS=y
 
@@ -396,6 +396,7 @@ CONFIG_PROC_EVENTS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -600,6 +601,7 @@ CONFIG_SGI_O2MACE_ETH=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=y
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)

arch/mips/configs/jaguar-atx_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:51 2007
+# Tue Feb 20 21:47:33 2007
 #
 CONFIG_MIPS=y
 
@@ -375,6 +375,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -518,9 +519,6 @@ CONFIG_EEPRO100=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_MV643XX_ETH=y
-CONFIG_MV643XX_ETH_0=y
-CONFIG_MV643XX_ETH_1=y
-CONFIG_MV643XX_ETH_2=y
 CONFIG_QLA3XXX=m
 
 #
@@ -833,6 +831,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/jazz_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:52 2007
+# Tue Feb 20 21:47:33 2007
 #
 CONFIG_MIPS=y
 
@@ -646,6 +646,7 @@ CONFIG_PARPORT_1284=y
 # Plug and Play support
 #
 # CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/jmr3927_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:53 2007
+# Tue Feb 20 21:47:34 2007
 #
 CONFIG_MIPS=y
 
@@ -384,6 +384,7 @@ CONFIG_PROC_EVENTS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -513,6 +514,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=y
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)

arch/mips/configs/lasat200_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:54 2007
+# Tue Feb 20 21:47:34 2007
 #
 CONFIG_MIPS=y
 
@@ -454,7 +454,6 @@ CONFIG_MTD_LASAT=y
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -469,6 +468,7 @@ CONFIG_MTD_LASAT=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -654,6 +654,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)

arch/mips/configs/malta_defconfig

@@ -145,6 +145,7 @@ CONFIG_SYS_SUPPORTS_MULTITHREADING=y
 CONFIG_MIPS_MT_FPAFF=y
 # CONFIG_64BIT_PHYS_ADDR is not set
 CONFIG_CPU_HAS_LLSC=y
+# CONFIG_CPU_HAS_SMARTMIPS is not set
 CONFIG_CPU_MIPSR2_IRQ_VI=y
 CONFIG_CPU_MIPSR2_SRS=y
 CONFIG_CPU_HAS_SYNC=y
@@ -152,6 +153,7 @@ CONFIG_GENERIC_HARDIRQS=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_IRQ_PER_CPU=y
 CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_SYS_SUPPORTS_SMARTMIPS=y
 CONFIG_ARCH_FLATMEM_ENABLE=y
 CONFIG_SELECT_MEMORY_MODEL=y
 CONFIG_FLATMEM_MANUAL=y

arch/mips/configs/mipssim_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:56 2007
+# Tue Feb 20 21:47:35 2007
 #
 CONFIG_MIPS=y
 
@@ -436,6 +436,7 @@ CONFIG_FIB_RULES=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -878,7 +879,6 @@ CONFIG_FORCED_INLINING=y
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="nfsroot=192.168.192.169:/u1/mipsel,timeo=20 ip=dhcp"
 # CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
 # CONFIG_RUNTIME_DEBUG is not set
 # CONFIG_MIPS_UNCACHED is not set
 

arch/mips/configs/mpc30x_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:56 2007
+# Tue Feb 20 21:47:35 2007
 #
 CONFIG_MIPS=y
 
@@ -405,6 +405,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -531,6 +532,7 @@ CONFIG_MII=m
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -883,6 +885,7 @@ CONFIG_USB_PEGASUS=m
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set

arch/mips/configs/ocelot_3_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:58 2007
+# Tue Feb 20 21:47:35 2007
 #
 CONFIG_MIPS=y
 
@@ -496,6 +496,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -713,9 +714,6 @@ CONFIG_E100=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_MV643XX_ETH=y
-CONFIG_MV643XX_ETH_0=y
-CONFIG_MV643XX_ETH_1=y
-CONFIG_MV643XX_ETH_2=y
 CONFIG_QLA3XXX=m
 # CONFIG_ATL1 is not set
 

arch/mips/configs/ocelot_c_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:58 2007
+# Tue Feb 20 21:47:36 2007
 #
 CONFIG_MIPS=y
 
@@ -393,6 +393,7 @@ CONFIG_PROC_EVENTS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -523,6 +524,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_BNX2 is not set
 # CONFIG_MV643XX_ETH is not set
 CONFIG_QLA3XXX=y
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)

arch/mips/configs/ocelot_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:59 2007
+# Tue Feb 20 21:47:36 2007
 #
 CONFIG_MIPS=y
 
@@ -390,6 +390,7 @@ CONFIG_PROC_EVENTS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -854,6 +855,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/ocelot_g_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:00 2007
+# Tue Feb 20 21:47:36 2007
 #
 CONFIG_MIPS=y
 
@@ -392,6 +392,7 @@ CONFIG_PROC_EVENTS=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -522,6 +523,7 @@ CONFIG_GALILEO_64240_ETH=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=y
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)

arch/mips/configs/pb1100_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:01 2007
+# Tue Feb 20 21:47:37 2007
 #
 CONFIG_MIPS=y
 
@@ -549,6 +549,7 @@ CONFIG_MTD_ALCHEMY=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1096,6 +1097,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pb1500_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:02 2007
+# Tue Feb 20 21:47:37 2007
 #
 CONFIG_MIPS=y
 
@@ -541,7 +541,6 @@ CONFIG_MTD_ALCHEMY=y
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -556,6 +555,7 @@ CONFIG_MTD_ALCHEMY=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -745,6 +745,7 @@ CONFIG_MIPS_AU1X00_ENET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1213,6 +1214,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pb1550_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:03 2007
+# Tue Feb 20 21:47:37 2007
 #
 CONFIG_MIPS=y
 
@@ -542,7 +542,6 @@ CONFIG_MTD_ALCHEMY=y
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -557,6 +556,7 @@ CONFIG_MTD_ALCHEMY=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -746,6 +746,7 @@ CONFIG_MIPS_AU1X00_ENET=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1206,6 +1207,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pnx8550-jbs_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:04 2007
+# Tue Feb 20 21:47:38 2007
 #
 CONFIG_MIPS=y
 
@@ -389,6 +389,7 @@ CONFIG_FW_LOADER=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -962,6 +963,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set
@@ -1229,6 +1231,7 @@ CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="console=ttyS1,38400n8 kgdb=ttyS0 root=/dev/nfs ip=bootp"
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_KGDB is not set
+CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 # CONFIG_MIPS_UNCACHED is not set
 

arch/mips/configs/pnx8550-stb810_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:04 2007
+# Tue Feb 20 21:47:38 2007
 #
 CONFIG_MIPS=y
 
@@ -386,6 +386,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -952,6 +953,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set
@@ -1219,6 +1221,7 @@ CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="console=ttyS1,38400n8 kgdb=ttyS0 root=/dev/nfs ip=bootp"
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_KGDB is not set
+CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 # CONFIG_MIPS_UNCACHED is not set
 

arch/mips/configs/pnx8550-v2pci_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:06 2007
+# Tue Feb 20 21:47:39 2007
 #
 CONFIG_MIPS=y
 
@@ -474,6 +474,7 @@ CONFIG_FW_LOADER=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -987,6 +988,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_ADM1021 is not set
 # CONFIG_SENSORS_ADM1025 is not set
 # CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
 # CONFIG_SENSORS_ADM1031 is not set
 # CONFIG_SENSORS_ADM9240 is not set
 # CONFIG_SENSORS_ASB100 is not set
@@ -1209,6 +1211,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set
@@ -1466,6 +1469,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/qemu_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:06 2007
+# Tue Feb 20 21:47:39 2007
 #
 CONFIG_MIPS=y
 
@@ -348,6 +348,7 @@ CONFIG_PROC_EVENTS=y
 # Plug and Play support
 #
 # CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/rbhma4500_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:07 2007
+# Tue Feb 20 21:47:39 2007
 #
 CONFIG_MIPS=y
 
@@ -560,7 +560,6 @@ CONFIG_MTD_CFI_UTIL=y
 # NAND Flash Device Drivers
 #
 # CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
 
 #
 # OneNAND Flash Device Drivers
@@ -576,6 +575,7 @@ CONFIG_MTD_CFI_UTIL=y
 # Plug and Play support
 #
 # CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1191,6 +1191,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set
@@ -1462,6 +1463,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/rm200_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:09 2007
+# Tue Feb 20 21:47:40 2007
 #
 CONFIG_MIPS=y
 
@@ -661,6 +661,7 @@ CONFIG_PARPORT_NOT_PC=y
 # Plug and Play support
 #
 # CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -1397,6 +1398,7 @@ CONFIG_USB_AUERSWALD=m
 CONFIG_USB_RIO500=m
 CONFIG_USB_LEGOTOWER=m
 CONFIG_USB_LCD=m
+# CONFIG_USB_BERRY_CHARGE is not set
 CONFIG_USB_LED=m
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 CONFIG_USB_CYTHERM=m

arch/mips/configs/sb1250-swarm_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:09 2007
+# Tue Feb 20 21:47:40 2007
 #
 CONFIG_MIPS=y
 
@@ -424,6 +424,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -581,6 +582,7 @@ CONFIG_NET_SB1250_MAC=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -945,6 +947,7 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=15
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
+CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_SB1XXX_CORELIS is not set
 
 #

arch/mips/configs/sead_defconfig

@@ -129,10 +129,12 @@ CONFIG_MIPS_MT_DISABLED=y
 # CONFIG_MIPS_VPE_LOADER is not set
 # CONFIG_64BIT_PHYS_ADDR is not set
 CONFIG_CPU_HAS_LLSC=y
+# CONFIG_CPU_HAS_SMARTMIPS is not set
 CONFIG_CPU_HAS_SYNC=y
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_SYS_SUPPORTS_SMARTMIPS=y
 CONFIG_ARCH_FLATMEM_ENABLE=y
 CONFIG_SELECT_MEMORY_MODEL=y
 CONFIG_FLATMEM_MANUAL=y

arch/mips/configs/tb0226_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:11 2007
+# Tue Feb 20 21:47:41 2007
 #
 CONFIG_MIPS=y
 
@@ -396,6 +396,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -920,6 +921,7 @@ CONFIG_USB_STORAGE=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set

arch/mips/configs/tb0229_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:12 2007
+# Tue Feb 20 21:47:41 2007
 #
 CONFIG_MIPS=y
 
@@ -397,6 +397,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -530,6 +531,7 @@ CONFIG_R8169=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 CONFIG_QLA3XXX=m
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -819,6 +821,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set

arch/mips/configs/tb0287_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:13 2007
+# Tue Feb 20 21:47:41 2007
 #
 CONFIG_MIPS=y
 
@@ -409,6 +409,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -675,6 +676,7 @@ CONFIG_R8169=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 # CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -1016,6 +1018,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_RIO500 is not set
 # CONFIG_USB_LEGOTOWER is not set
 # CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
 # CONFIG_USB_LED is not set
 # CONFIG_USB_CYPRESS_CY7C63 is not set
 # CONFIG_USB_CYTHERM is not set

arch/mips/configs/workpad_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:13 2007
+# Tue Feb 20 21:47:42 2007
 #
 CONFIG_MIPS=y
 
@@ -396,6 +396,7 @@ CONFIG_CONNECTOR=m
 # Plug and Play support
 #
 # CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/wrppmc_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:14 2007
+# Tue Feb 20 21:47:42 2007
 #
 CONFIG_MIPS=y
 
@@ -400,6 +400,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/configs/yosemite_defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:28:15 2007
+# Tue Feb 20 21:47:42 2007
 #
 CONFIG_MIPS=y
 
@@ -381,6 +381,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices
@@ -841,6 +842,7 @@ CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_KGDB is not set
+CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 
 #

arch/mips/defconfig

 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.20
-# Sun Feb 18 21:27:34 2007
+# Tue Feb 20 21:47:14 2007
 #
 CONFIG_MIPS=y
 
@@ -620,6 +620,7 @@ CONFIG_CONNECTOR=m
 #
 # Plug and Play support
 #
+# CONFIG_PNPACPI is not set
 
 #
 # Block devices

arch/mips/kernel/asm-offsets.c

@@ -64,6 +64,9 @@ void output_ptreg_defines(void)
 	offset("#define PT_R31    ", struct pt_regs, regs[31]);
 	offset("#define PT_LO     ", struct pt_regs, lo);
 	offset("#define PT_HI     ", struct pt_regs, hi);
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	offset("#define PT_ACX    ", struct pt_regs, acx);
+#endif
 	offset("#define PT_EPC    ", struct pt_regs, cp0_epc);
 	offset("#define PT_BVADDR ", struct pt_regs, cp0_badvaddr);
 	offset("#define PT_STATUS ", struct pt_regs, cp0_status);
@@ -246,6 +249,7 @@ void output_sc_defines(void)
 	text("/* Linux sigcontext offsets. */");
 	offset("#define SC_REGS       ", struct sigcontext, sc_regs);
 	offset("#define SC_FPREGS     ", struct sigcontext, sc_fpregs);
+	offset("#define SC_ACX        ", struct sigcontext, sc_acx);
 	offset("#define SC_MDHI       ", struct sigcontext, sc_mdhi);
 	offset("#define SC_MDLO       ", struct sigcontext, sc_mdlo);
 	offset("#define SC_PC         ", struct sigcontext, sc_pc);

arch/mips/kernel/ptrace.c

@@ -236,6 +236,11 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 		case MMLO:
 			tmp = regs->lo;
 			break;
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		case ACX:
+			tmp = regs->acx;
+			break;
+#endif
 		case FPC_CSR:
 			tmp = child->thread.fpu.fcr31;
 			break;
@@ -362,6 +367,11 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 		case MMLO:
 			regs->lo = data;
 			break;
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		case ACX:
+			regs->acx = data;
+			break;
+#endif
 		case FPC_CSR:
 			child->thread.fpu.fcr31 = data;
 			break;

arch/mips/kernel/signal.c

@@ -89,6 +89,9 @@ int setup_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc)
 	for (i = 1; i < 32; i++)
 		err |= __put_user(regs->regs[i], &sc->sc_regs[i]);
 
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	err |= __put_user(regs->acx, &sc->sc_acx);
+#endif
 	err |= __put_user(regs->hi, &sc->sc_mdhi);
 	err |= __put_user(regs->lo, &sc->sc_mdlo);
 	if (cpu_has_dsp) {
@@ -132,6 +135,10 @@ int restore_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc)
 	current_thread_info()->restart_block.fn = do_no_restart_syscall;
 
 	err |= __get_user(regs->cp0_epc, &sc->sc_pc);
+
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	err |= __get_user(regs->acx, &sc->sc_acx);
+#endif
 	err |= __get_user(regs->hi, &sc->sc_mdhi);
 	err |= __get_user(regs->lo, &sc->sc_mdlo);
 	if (cpu_has_dsp) {

arch/mips/kernel/smp.c

@@ -51,31 +51,14 @@ int __cpu_logical_map[NR_CPUS];		/* Map logical to physical */
 EXPORT_SYMBOL(phys_cpu_present_map);
 EXPORT_SYMBOL(cpu_online_map);
 
+/* This happens early in bootup, can't really do it better */
 static void smp_tune_scheduling (void)
 {
 	struct cache_desc *cd = &current_cpu_data.scache;
-	unsigned long cachesize;       /* kB   */
-	unsigned long cpu_khz;
+	unsigned long cachesize = cd->linesz * cd->sets * cd->ways;
 
-	/*
-	 * Crude estimate until we actually meassure ...
-	 */
-	cpu_khz = loops_per_jiffy * 2 * HZ / 1000;
-
-	/*
-	 * Rough estimation for SMP scheduling, this is the number of
-	 * cycles it takes for a fully memory-limited process to flush
-	 * the SMP-local cache.
-	 *
-	 * (For a P5 this pretty much means we will choose another idle
-	 *  CPU almost always at wakeup time (this is due to the small
-	 *  L1 cache), on PIIs it's around 50-100 usecs, depending on
-	 *  the cache size)
-	 */
-	if (!cpu_khz)
-		return;
-
-	cachesize = cd->linesz * cd->sets * cd->ways;
+	if (cachesize > max_cache_size)
+		max_cache_size = cachesize;
 }
 
 extern void __init calibrate_delay(void);

arch/mips/kernel/traps.c

@@ -229,6 +229,9 @@ void show_regs(struct pt_regs *regs)
 			printk("\n");
 	}
 
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	printk("Acx    : %0*lx\n", field, regs->acx);
+#endif
 	printk("Hi    : %0*lx\n", field, regs->hi);
 	printk("Lo    : %0*lx\n", field, regs->lo);
 

arch/mips/mm/ioremap.c

@@ -6,13 +6,98 @@
  * (C) Copyright 1995 1996 Linus Torvalds
  * (C) Copyright 2001, 2002 Ralf Baechle
  */
-#include <linux/mm.h>
 #include <linux/module.h>
 #include <asm/addrspace.h>
 #include <asm/byteorder.h>
 
 #include <linux/vmalloc.h>
-#include <linux/io.h>
+#include <asm/cacheflush.h>
+#include <asm/io.h>
+#include <asm/tlbflush.h>
+
+static inline void remap_area_pte(pte_t * pte, unsigned long address,
+	phys_t size, phys_t phys_addr, unsigned long flags)
+{
+	phys_t end;
+	unsigned long pfn;
+	pgprot_t pgprot = __pgprot(_PAGE_GLOBAL | _PAGE_PRESENT | __READABLE
+	                           | __WRITEABLE | flags);
+
+	address &= ~PMD_MASK;
+	end = address + size;
+	if (end > PMD_SIZE)
+		end = PMD_SIZE;
+	if (address >= end)
+		BUG();
+	pfn = phys_addr >> PAGE_SHIFT;
+	do {
+		if (!pte_none(*pte)) {
+			printk("remap_area_pte: page already exists\n");
+			BUG();
+		}
+		set_pte(pte, pfn_pte(pfn, pgprot));
+		address += PAGE_SIZE;
+		pfn++;
+		pte++;
+	} while (address && (address < end));
+}
+
+static inline int remap_area_pmd(pmd_t * pmd, unsigned long address,
+	phys_t size, phys_t phys_addr, unsigned long flags)
+{
+	phys_t end;
+
+	address &= ~PGDIR_MASK;
+	end = address + size;
+	if (end > PGDIR_SIZE)
+		end = PGDIR_SIZE;
+	phys_addr -= address;
+	if (address >= end)
+		BUG();
+	do {
+		pte_t * pte = pte_alloc_kernel(pmd, address);
+		if (!pte)
+			return -ENOMEM;
+		remap_area_pte(pte, address, end - address, address + phys_addr, flags);
+		address = (address + PMD_SIZE) & PMD_MASK;
+		pmd++;
+	} while (address && (address < end));
+	return 0;
+}
+
+static int remap_area_pages(unsigned long address, phys_t phys_addr,
+	phys_t size, unsigned long flags)
+{
+	int error;
+	pgd_t * dir;
+	unsigned long end = address + size;
+
+	phys_addr -= address;
+	dir = pgd_offset(&init_mm, address);
+	flush_cache_all();
+	if (address >= end)
+		BUG();
+	do {
+		pud_t *pud;
+		pmd_t *pmd;
+
+		error = -ENOMEM;
+		pud = pud_alloc(&init_mm, dir, address);
+		if (!pud)
+			break;
+		pmd = pmd_alloc(&init_mm, pud, address);
+		if (!pmd)
+			break;
+		if (remap_area_pmd(pmd, address, end - address,
+					 phys_addr + address, flags))
+			break;
+		error = 0;
+		address = (address + PGDIR_SIZE) & PGDIR_MASK;
+		dir++;
+	} while (address && (address < end));
+	flush_tlb_all();
+	return error;
+}
 
 /*
  * Generic mapping function (not visible outside):
@@ -36,7 +121,6 @@ void __iomem * __ioremap(phys_t phys_addr, phys_t size, unsigned long flags)
 	unsigned long offset;
 	phys_t last_addr;
 	void * addr;
-	pgprot_t pgprot;
 
 	phys_addr = fixup_bigphys_addr(phys_addr, size);
 
@@ -68,9 +152,6 @@ void __iomem * __ioremap(phys_t phys_addr, phys_t size, unsigned long flags)
 				return NULL;
 	}
 
-	pgprot = __pgprot(_PAGE_GLOBAL | _PAGE_PRESENT | __READABLE
-			  | __WRITEABLE | flags);
-
 	/*
 	 * Mappings have to be page-aligned
 	 */
@@ -85,8 +166,7 @@ void __iomem * __ioremap(phys_t phys_addr, phys_t size, unsigned long flags)
 	if (!area)
 		return NULL;
 	addr = area->addr;
-	if (ioremap_page_range((unsigned long)addr, (unsigned long)addr + size,
-			       phys_addr, pgprot)) {
+	if (remap_area_pages((unsigned long) addr, phys_addr, size, flags)) {
 		vunmap(addr);
 		return NULL;
 	}

arch/mips/momentum/jaguar_atx/platform.c

@@ -200,7 +200,7 @@ static int __init mv643xx_eth_add_pds(void)
 	int ret;
 
 	get_mac(mac);
-	eth_mac_add(eth1_mac_addr, mac, 0);
+	eth_mac_add(eth0_mac_addr, mac, 0);
 	eth_mac_add(eth1_mac_addr, mac, 1);
 	eth_mac_add(eth2_mac_addr, mac, 2);
 	ret = platform_add_devices(mv643xx_eth_pd_devs,

arch/mips/momentum/ocelot_3/platform.c

@@ -200,7 +200,7 @@ static int __init mv643xx_eth_add_pds(void)
 	int ret;
 
 	get_mac(mac);
-	eth_mac_add(eth1_mac_addr, mac, 0);
+	eth_mac_add(eth0_mac_addr, mac, 0);
 	eth_mac_add(eth1_mac_addr, mac, 1);
 	eth_mac_add(eth2_mac_addr, mac, 2);
 	ret = platform_add_devices(mv643xx_eth_pd_devs,

arch/mips/momentum/ocelot_c/platform.c

@@ -174,7 +174,7 @@ static int __init mv643xx_eth_add_pds(void)
 	int ret;
 
 	get_mac(mac);
-	eth_mac_add(eth1_mac_addr, mac, 0);
+	eth_mac_add(eth0_mac_addr, mac, 0);
 	eth_mac_add(eth1_mac_addr, mac, 1);
 	ret = platform_add_devices(mv643xx_eth_pd_devs,
 			ARRAY_SIZE(mv643xx_eth_pd_devs));

drivers/serial/serial_txx9.c

@@ -38,6 +38,8 @@
  *		Fix some spin_locks.
  *		Do not call uart_add_one_port for absent ports.
  *	1.07	Use CONFIG_SERIAL_TXX9_NR_UARTS.  Cleanup.
+ *	1.08	Use platform_device.
+ *		Fix and cleanup suspend/resume/initialization codes.
  */
 
 #if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
@@ -50,7 +52,7 @@
 #include <linux/console.h>
 #include <linux/sysrq.h>
 #include <linux/delay.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
 #include <linux/pci.h>
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
@@ -60,7 +62,7 @@
 
 #include <asm/io.h>
 
-static char *serial_version = "1.07";
+static char *serial_version = "1.08";
 static char *serial_name = "TX39/49 Serial driver";
 
 #define PASS_LIMIT	256
@@ -94,12 +96,7 @@ static char *serial_name = "TX39/49 Serial driver";
 
 struct uart_txx9_port {
 	struct uart_port	port;
-
-	/*
-	 * We provide a per-port pm hook.
-	 */
-	void			(*pm)(struct uart_port *port,
-				      unsigned int state, unsigned int old);
+	/* No additional info for now */
 };
 
 #define TXX9_REGION_SIZE	0x24
@@ -277,6 +274,31 @@ static void serial_txx9_enable_ms(struct uart_port *port)
 	/* TXX9-SIO can not control DTR... */
 }
 
+static void serial_txx9_initialize(struct uart_port *port)
+{
+	struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+	unsigned int tmout = 10000;
+
+	sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
+	/* TX4925 BUG WORKAROUND.  Accessing SIOC register
+	 * immediately after soft reset causes bus error. */
+	mmiowb();
+	udelay(1);
+	while ((sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST) && --tmout)
+		udelay(1);
+	/* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
+	sio_set(up, TXX9_SIFCR,
+		TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
+	/* initial settings */
+	sio_out(up, TXX9_SILCR,
+		TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
+		((up->port.flags & UPF_TXX9_USE_SCLK) ?
+		 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
+	sio_quot_set(up, uart_get_divisor(port, 9600));
+	sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
+	sio_out(up, TXX9_SIDICR, 0);
+}
+
 static inline void
 receive_chars(struct uart_txx9_port *up, unsigned int *status)
 {
@@ -657,9 +679,8 @@ static void
 serial_txx9_pm(struct uart_port *port, unsigned int state,
 	      unsigned int oldstate)
 {
-	struct uart_txx9_port *up = (struct uart_txx9_port *)port;
-	if (up->pm)
-		up->pm(port, state, oldstate);
+	if (state == 0)
+		serial_txx9_initialize(port);
 }
 
 static int serial_txx9_request_resource(struct uart_txx9_port *up)
@@ -732,7 +753,6 @@ static int serial_txx9_request_port(struct uart_port *port)
 static void serial_txx9_config_port(struct uart_port *port, int uflags)
 {
 	struct uart_txx9_port *up = (struct uart_txx9_port *)port;
-	unsigned long flags;
 	int ret;
 
 	/*
@@ -749,30 +769,7 @@ static void serial_txx9_config_port(struct uart_port *port, int uflags)
 	if (up->port.line == up->port.cons->index)
 		return;
 #endif
-	spin_lock_irqsave(&up->port.lock, flags);
-	/*
-	 * Reset the UART.
-	 */
-	sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
-#ifdef CONFIG_CPU_TX49XX
-	/* TX4925 BUG WORKAROUND.  Accessing SIOC register
-	 * immediately after soft reset causes bus error. */
-	iob();
-	udelay(1);
-#endif
-	while (sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST)
-		;
-	/* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
-	sio_set(up, TXX9_SIFCR,
-		TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
-	/* initial settings */
-	sio_out(up, TXX9_SILCR,
-		TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
-		((up->port.flags & UPF_TXX9_USE_SCLK) ?
-		 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
-	sio_quot_set(up, uart_get_divisor(port, 9600));
-	sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
-	spin_unlock_irqrestore(&up->port.lock, flags);
+	serial_txx9_initialize(port);
 }
 
 static int
@@ -818,7 +815,8 @@ static struct uart_ops serial_txx9_pops = {
 
 static struct uart_txx9_port serial_txx9_ports[UART_NR];
 
-static void __init serial_txx9_register_ports(struct uart_driver *drv)
+static void __init serial_txx9_register_ports(struct uart_driver *drv,
+					      struct device *dev)
 {
 	int i;
 
@@ -827,6 +825,7 @@ static void __init serial_txx9_register_ports(struct uart_driver *drv)
 
 		up->port.line = i;
 		up->port.ops = &serial_txx9_pops;
+		up->port.dev = dev;
 		if (up->port.iobase || up->port.mapbase)
 			uart_add_one_port(drv, &up->port);
 	}
@@ -898,7 +897,7 @@ serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
 	sio_out(up, TXX9_SIDICR, ier);
 }
 
-static int serial_txx9_console_setup(struct console *co, char *options)
+static int __init serial_txx9_console_setup(struct console *co, char *options)
 {
 	struct uart_port *port;
 	struct uart_txx9_port *up;
@@ -919,17 +918,7 @@ static int serial_txx9_console_setup(struct console *co, char *options)
 	if (!port->ops)
 		return -ENODEV;
 
-	/*
-	 *	Disable UART interrupts, set DTR and RTS high
-	 *	and set speed.
-	 */
-	sio_out(up, TXX9_SIDICR, 0);
-	/* initial settings */
-	sio_out(up, TXX9_SILCR,
-		TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
-		((port->flags & UPF_TXX9_USE_SCLK) ?
-		 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
-	sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
+	serial_txx9_initialize(&up->port);
 
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
@@ -981,31 +970,6 @@ int __init early_serial_txx9_setup(struct uart_port *port)
 	return 0;
 }
 
-#ifdef ENABLE_SERIAL_TXX9_PCI
-#ifdef CONFIG_PM
-/**
- *	serial_txx9_suspend_port - suspend one serial port
- *	@line:  serial line number
- *
- *	Suspend one serial port.
- */
-static void serial_txx9_suspend_port(int line)
-{
-	uart_suspend_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
-}
-
-/**
- *	serial_txx9_resume_port - resume one serial port
- *	@line:  serial line number
- *
- *	Resume one serial port.
- */
-static void serial_txx9_resume_port(int line)
-{
-	uart_resume_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
-}
-#endif
-
 static DEFINE_MUTEX(serial_txx9_mutex);
 
 /**
@@ -1028,8 +992,18 @@ static int __devinit serial_txx9_register_port(struct uart_port *port)
 	mutex_lock(&serial_txx9_mutex);
 	for (i = 0; i < UART_NR; i++) {
 		uart = &serial_txx9_ports[i];
-		if (!(uart->port.iobase || uart->port.mapbase))
+		if (uart_match_port(&uart->port, port)) {
+			uart_remove_one_port(&serial_txx9_reg, &uart->port);
 			break;
+		}
+	}
+	if (i == UART_NR) {
+		/* Find unused port */
+		for (i = 0; i < UART_NR; i++) {
+			uart = &serial_txx9_ports[i];
+			if (!(uart->port.iobase || uart->port.mapbase))
+				break;
+		}
 	}
 	if (i < UART_NR) {
 		uart->port.iobase = port->iobase;
@@ -1071,6 +1045,95 @@ static void __devexit serial_txx9_unregister_port(int line)
 	mutex_unlock(&serial_txx9_mutex);
 }
 
+/*
+ * Register a set of serial devices attached to a platform device.
+ */
+static int __devinit serial_txx9_probe(struct platform_device *dev)
+{
+	struct uart_port *p = dev->dev.platform_data;
+	struct uart_port port;
+	int ret, i;
+
+	memset(&port, 0, sizeof(struct uart_port));
+	for (i = 0; p && p->uartclk != 0; p++, i++) {
+		port.iobase	= p->iobase;
+		port.membase	= p->membase;
+		port.irq	= p->irq;
+		port.uartclk	= p->uartclk;
+		port.iotype	= p->iotype;
+		port.flags	= p->flags;
+		port.mapbase	= p->mapbase;
+		port.dev	= &dev->dev;
+		ret = serial_txx9_register_port(&port);
+		if (ret < 0) {
+			dev_err(&dev->dev, "unable to register port at index %d "
+				"(IO%x MEM%lx IRQ%d): %d\n", i,
+				p->iobase, p->mapbase, p->irq, ret);
+		}
+	}
+	return 0;
+}
+
+/*
+ * Remove serial ports registered against a platform device.
+ */
+static int __devexit serial_txx9_remove(struct platform_device *dev)
+{
+	int i;
+
+	for (i = 0; i < UART_NR; i++) {
+		struct uart_txx9_port *up = &serial_txx9_ports[i];
+
+		if (up->port.dev == &dev->dev)
+			serial_txx9_unregister_port(i);
+	}
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int serial_txx9_suspend(struct platform_device *dev, pm_message_t state)
+{
+	int i;
+
+	for (i = 0; i < UART_NR; i++) {
+		struct uart_txx9_port *up = &serial_txx9_ports[i];
+
+		if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
+			uart_suspend_port(&serial_txx9_reg, &up->port);
+	}
+
+	return 0;
+}
+
+static int serial_txx9_resume(struct platform_device *dev)
+{
+	int i;
+
+	for (i = 0; i < UART_NR; i++) {
+		struct uart_txx9_port *up = &serial_txx9_ports[i];
+
+		if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
+			uart_resume_port(&serial_txx9_reg, &up->port);
+	}
+
+	return 0;
+}
+#endif
+
+static struct platform_driver serial_txx9_plat_driver = {
+	.probe		= serial_txx9_probe,
+	.remove		= __devexit_p(serial_txx9_remove),
+#ifdef CONFIG_PM
+	.suspend	= serial_txx9_suspend,
+	.resume		= serial_txx9_resume,
+#endif
+	.driver		= {
+		.name	= "serial_txx9",
+		.owner	= THIS_MODULE,
+	},
+};
+
+#ifdef ENABLE_SERIAL_TXX9_PCI
 /*
  * Probe one serial board.  Unfortunately, there is no rhyme nor reason
  * to the arrangement of serial ports on a PCI card.
@@ -1097,20 +1160,22 @@ pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
 	line = serial_txx9_register_port(&port);
 	if (line < 0) {
 		printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
+		pci_disable_device(dev);
+		return line;
 	}
-	pci_set_drvdata(dev, (void *)(long)line);
+	pci_set_drvdata(dev, &serial_txx9_ports[line]);
 
 	return 0;
 }
 
 static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev)
 {
-	int line = (int)(long)pci_get_drvdata(dev);
+	struct uart_txx9_port *up = pci_get_drvdata(dev);
 
 	pci_set_drvdata(dev, NULL);
 
-	if (line) {
-		serial_txx9_unregister_port(line);
+	if (up) {
+		serial_txx9_unregister_port(up->port.line);
 		pci_disable_device(dev);
 	}
 }
@@ -1118,10 +1183,10 @@ static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev)
 #ifdef CONFIG_PM
 static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
 {
-	int line = (int)(long)pci_get_drvdata(dev);
+	struct uart_txx9_port *up = pci_get_drvdata(dev);
 
-	if (line)
-		serial_txx9_suspend_port(line);
+	if (up)
+		uart_suspend_port(&serial_txx9_reg, &up->port);
 	pci_save_state(dev);
 	pci_set_power_state(dev, pci_choose_state(dev, state));
 	return 0;
@@ -1129,15 +1194,12 @@ static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
 
 static int pciserial_txx9_resume_one(struct pci_dev *dev)
 {
-	int line = (int)(long)pci_get_drvdata(dev);
+	struct uart_txx9_port *up = pci_get_drvdata(dev);
 
 	pci_set_power_state(dev, PCI_D0);
 	pci_restore_state(dev);
-
-	if (line) {
-		pci_enable_device(dev);
-		serial_txx9_resume_port(line);
-	}
+	if (up)
+		uart_resume_port(&serial_txx9_reg, &up->port);
 	return 0;
 }
 #endif
@@ -1161,6 +1223,8 @@ static struct pci_driver serial_txx9_pci_driver = {
 MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
 #endif /* ENABLE_SERIAL_TXX9_PCI */
 
+static struct platform_device *serial_txx9_plat_devs;
+
 static int __init serial_txx9_init(void)
 {
 	int ret;
@@ -1168,13 +1232,39 @@ static int __init serial_txx9_init(void)
  	printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
 
 	ret = uart_register_driver(&serial_txx9_reg);
-	if (ret >= 0) {
-		serial_txx9_register_ports(&serial_txx9_reg);
+	if (ret)
+		goto out;
+
+	serial_txx9_plat_devs = platform_device_alloc("serial_txx9", -1);
+	if (!serial_txx9_plat_devs) {
+		ret = -ENOMEM;
+		goto unreg_uart_drv;
+	}
+
+	ret = platform_device_add(serial_txx9_plat_devs);
+	if (ret)
+		goto put_dev;
+
+	serial_txx9_register_ports(&serial_txx9_reg,
+				   &serial_txx9_plat_devs->dev);
+
+	ret = platform_driver_register(&serial_txx9_plat_driver);
+	if (ret)
+		goto del_dev;
 
 #ifdef ENABLE_SERIAL_TXX9_PCI
-		ret = pci_register_driver(&serial_txx9_pci_driver);
+	ret = pci_register_driver(&serial_txx9_pci_driver);
 #endif
-	}
+	if (ret == 0)
+		goto out;
+
+ del_dev:
+	platform_device_del(serial_txx9_plat_devs);
+ put_dev:
+	platform_device_put(serial_txx9_plat_devs);
+ unreg_uart_drv:
+	uart_unregister_driver(&serial_txx9_reg);
+ out:
 	return ret;
 }
 
@@ -1185,6 +1275,8 @@ static void __exit serial_txx9_exit(void)
 #ifdef ENABLE_SERIAL_TXX9_PCI
 	pci_unregister_driver(&serial_txx9_pci_driver);
 #endif
+	platform_driver_unregister(&serial_txx9_plat_driver);
+	platform_device_unregister(serial_txx9_plat_devs);
 	for (i = 0; i < UART_NR; i++) {
 		struct uart_txx9_port *up = &serial_txx9_ports[i];
 		if (up->port.iobase || up->port.mapbase)

include/asm-mips/ptrace.h

@@ -21,6 +21,7 @@
 #define FPC_EIR		70
 #define DSP_BASE	71		/* 3 more hi / lo register pairs */
 #define DSP_CONTROL	77
+#define ACX		78
 
 /*
  * This struct defines the way the registers are stored on the stack during a
@@ -39,6 +40,9 @@ struct pt_regs {
 	unsigned long cp0_status;
 	unsigned long hi;
 	unsigned long lo;
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	unsigned long acx;
+#endif
 	unsigned long cp0_badvaddr;
 	unsigned long cp0_cause;
 	unsigned long cp0_epc;

include/asm-mips/sigcontext.h

@@ -23,7 +23,7 @@ struct sigcontext {
 	unsigned long long	sc_pc;
 	unsigned long long	sc_regs[32];
 	unsigned long long	sc_fpregs[32];
-	unsigned int		sc_ownedfp;	/* Unused */
+	unsigned int		sc_acx;		/* Was sc_ownedfp */
 	unsigned int		sc_fpc_csr;
 	unsigned int		sc_fpc_eir;	/* Unused */
 	unsigned int		sc_used_math;
@@ -79,7 +79,7 @@ struct sigcontext32 {
 	__u64		sc_pc;
 	__u64		sc_regs[32];
 	__u64		sc_fpregs[32];
-	__u32		sc_ownedfp;	/* Unused */
+	__u32		sc_acx;		/* Only MIPS32; was sc_ownedfp */
 	__u32		sc_fpc_csr;
 	__u32		sc_fpc_eir;	/* Unused */
 	__u32		sc_used_math;

include/asm-mips/stackframe.h

@@ -29,16 +29,25 @@
 		.endm
 
 		.macro	SAVE_TEMP
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		mflhxu	v1
+		LONG_S	v1, PT_LO(sp)
+		mflhxu	v1
+		LONG_S	v1, PT_HI(sp)
+		mflhxu	v1
+		LONG_S	v1, PT_ACX(sp)
+#else
 		mfhi	v1
+		LONG_S	v1, PT_HI(sp)
+		mflo	v1
+		LONG_S	v1, PT_LO(sp)
+#endif
 #ifdef CONFIG_32BIT
 		LONG_S	$8, PT_R8(sp)
 		LONG_S	$9, PT_R9(sp)
 #endif
-		LONG_S	v1, PT_HI(sp)
-		mflo	v1
 		LONG_S	$10, PT_R10(sp)
 		LONG_S	$11, PT_R11(sp)
-		LONG_S	v1,  PT_LO(sp)
 		LONG_S	$12, PT_R12(sp)
 		LONG_S	$13, PT_R13(sp)
 		LONG_S	$14, PT_R14(sp)
@@ -182,16 +191,25 @@
 		.endm
 
 		.macro	RESTORE_TEMP
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		LONG_L	$24, PT_ACX(sp)
+		mtlhx	$24
+		LONG_L	$24, PT_HI(sp)
+		mtlhx	$24
 		LONG_L	$24, PT_LO(sp)
+		mtlhx	$24
+#else
+		LONG_L	$24, PT_LO(sp)
+		mtlo	$24
+		LONG_L	$24, PT_HI(sp)
+		mthi	$24
+#endif
 #ifdef CONFIG_32BIT
 		LONG_L	$8, PT_R8(sp)
 		LONG_L	$9, PT_R9(sp)
 #endif
-		mtlo	$24
-		LONG_L	$24, PT_HI(sp)
 		LONG_L	$10, PT_R10(sp)
 		LONG_L	$11, PT_R11(sp)
-		mthi	$24
 		LONG_L	$12, PT_R12(sp)
 		LONG_L	$13, PT_R13(sp)
 		LONG_L	$14, PT_R14(sp)