Commit 6436db37 authored by Linus Walleij's avatar Linus Walleij Committed by Jonathan Cameron

iio: st_sensors: read each channel individually

The current buffer read code tries to optimize reads from the
sensor data registers by issuing a single read operation across
all the indata registers.

This doesn't work: when the LIS331DL accelerometer sensor is
configured to open drain, active low interrupt mode, this will
just clear the XDA (X-axis data available) bit in the STATUS_REG
register (0x27), while YDA, ZDA and even ZYXDA remain set to 1,
and the internal logic of the sensor holds the DRDY (INT1) line
asserted (the value of the status register is 0xee).

If we instead issue one read operation per enabled channel
(X, Y, Z) things start working and we can use open drain and
active low interrupts.

Note that a backported patch fixing this issue will be heading
via the fixes branch but changes in this file already in staging-next
will make that patch 'look' rather different.  The code in here
is the correct one when that clash hits.

Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarJonathan Cameron <jic23@kernel.org>
parent 850c25c8
......@@ -24,67 +24,30 @@
int st_sensors_get_buffer_element(struct iio_dev *indio_dev, u8 *buf)
{
u8 addr[3]; /* no ST sensor has more than 3 channels */
int i, n = 0, len;
int i, len;
int total = 0;
struct st_sensor_data *sdata = iio_priv(indio_dev);
unsigned int num_data_channels = sdata->num_data_channels;
unsigned int byte_for_channel =
indio_dev->channels[0].scan_type.storagebits >> 3;
for (i = 0; i < num_data_channels; i++) {
unsigned int bytes_to_read;
if (test_bit(i, indio_dev->active_scan_mask)) {
addr[n] = indio_dev->channels[i].address;
n++;
}
}
switch (n) {
case 1:
len = sdata->tf->read_multiple_byte(&sdata->tb, sdata->dev,
addr[0], byte_for_channel, buf, sdata->multiread_bit);
break;
case 2:
if ((addr[1] - addr[0]) == byte_for_channel) {
bytes_to_read = indio_dev->channels[i].scan_type.storagebits >> 3;
len = sdata->tf->read_multiple_byte(&sdata->tb,
sdata->dev, addr[0], byte_for_channel * n,
buf, sdata->multiread_bit);
} else {
u8 *rx_array;
rx_array = kmalloc(byte_for_channel * num_data_channels,
GFP_KERNEL);
if (!rx_array)
return -ENOMEM;
sdata->dev, indio_dev->channels[i].address,
bytes_to_read,
buf + total, sdata->multiread_bit);
len = sdata->tf->read_multiple_byte(&sdata->tb,
sdata->dev, addr[0],
byte_for_channel * num_data_channels,
rx_array, sdata->multiread_bit);
if (len < 0) {
kfree(rx_array);
return len;
}
if (len < bytes_to_read)
return -EIO;
for (i = 0; i < n * byte_for_channel; i++) {
if (i < n)
buf[i] = rx_array[i];
else
buf[i] = rx_array[n + i];
/* Advance the buffer pointer */
total += len;
}
kfree(rx_array);
len = byte_for_channel * n;
}
break;
case 3:
len = sdata->tf->read_multiple_byte(&sdata->tb, sdata->dev,
addr[0], byte_for_channel * num_data_channels,
buf, sdata->multiread_bit);
break;
default:
return -EINVAL;
}
if (len != byte_for_channel * n)
return -EIO;
return len;
return total;
}
EXPORT_SYMBOL(st_sensors_get_buffer_element);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment