Commit 66583560 authored by Krzysztof Kozlowski's avatar Krzysztof Kozlowski Committed by Kukjin Kim

ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4

Add Hardkernel Odroid XU4 board Device Tree sources. The board differs
from Odroid XU3 and XU3-Lite by:
1. No green and red LEDs (except standard red power LED).
2. Only two PWM outputs are used (fan and blue LED)
3. No audio codec.
4. Two USB3 ports in host mode (no micro USB3 connector for OTG).
5. Realtek RTL8153-CG gigabit network adapter (instead of SMSC9514).
6. Additional connector with IO ports (I2S_0, I2C_5).
7. No DisplayPort (like XU3-Lite).
8. No TI INA231 power measurement sensors (like XU3-Lite).
Signed-off-by: default avatarKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: default avatarJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: default avatarKukjin Kim <kgene@kernel.org>
parent 8cec7349
...@@ -123,6 +123,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ ...@@ -123,6 +123,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
exynos5420-smdk5420.dtb \ exynos5420-smdk5420.dtb \
exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3.dtb \
exynos5422-odroidxu3-lite.dtb \ exynos5422-odroidxu3-lite.dtb \
exynos5422-odroidxu4.dtb \
exynos5440-sd5v1.dtb \ exynos5440-sd5v1.dtb \
exynos5440-ssdk5440.dtb \ exynos5440-ssdk5440.dtb \
exynos5800-peach-pi.dtb exynos5800-peach-pi.dtb
......
...@@ -46,40 +46,6 @@ emmc_pwrseq: pwrseq { ...@@ -46,40 +46,6 @@ emmc_pwrseq: pwrseq {
reset-gpios = <&gpd1 0 1>; reset-gpios = <&gpd1 0 1>;
}; };
pwmleds {
compatible = "pwm-leds";
greenled {
label = "green:mmc0";
pwms = <&pwm 1 2000000 0>;
pwm-names = "pwm1";
/*
* Green LED is much brighter than the others
* so limit its max brightness
*/
max_brightness = <127>;
linux,default-trigger = "mmc0";
};
blueled {
label = "blue:heartbeat";
pwms = <&pwm 2 2000000 0>;
pwm-names = "pwm2";
max_brightness = <255>;
linux,default-trigger = "heartbeat";
};
};
gpioleds {
compatible = "gpio-leds";
redled {
label = "red:microSD";
gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "mmc1";
};
};
fan0: pwm-fan { fan0: pwm-fan {
compatible = "pwm-fan"; compatible = "pwm-fan";
pwms = <&pwm 0 20972 0>; pwms = <&pwm 0 20972 0>;
...@@ -417,18 +383,6 @@ emmc_nrst_pin: emmc-nrst { ...@@ -417,18 +383,6 @@ emmc_nrst_pin: emmc-nrst {
}; };
}; };
&pwm {
/*
* PWM 0 -- fan
* PWM 1 -- Green LED
* PWM 2 -- Blue LED
* PWM 3 -- on MIPI connector for backlight
*/
pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>;
pinctrl-names = "default";
status = "okay";
};
&tmu_cpu0 { &tmu_cpu0 {
vtmu-supply = <&ldo7_reg>; vtmu-supply = <&ldo7_reg>;
status = "okay"; status = "okay";
...@@ -464,9 +418,7 @@ &usbdrd_dwc3_0 { ...@@ -464,9 +418,7 @@ &usbdrd_dwc3_0 {
dr_mode = "host"; dr_mode = "host";
}; };
&usbdrd_dwc3_1 { /* usbdrd_dwc3_1 mode customized in each board */
dr_mode = "otg";
};
&usbdrd3_0 { &usbdrd3_0 {
vdd33-supply = <&ldo9_reg>; vdd33-supply = <&ldo9_reg>;
......
...@@ -18,4 +18,54 @@ ...@@ -18,4 +18,54 @@
/ { / {
model = "Hardkernel Odroid XU3 Lite"; model = "Hardkernel Odroid XU3 Lite";
compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5"; compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5";
pwmleds {
compatible = "pwm-leds";
greenled {
label = "green:mmc0";
pwms = <&pwm 1 2000000 0>;
pwm-names = "pwm1";
/*
* Green LED is much brighter than the others
* so limit its max brightness
*/
max_brightness = <127>;
linux,default-trigger = "mmc0";
};
blueled {
label = "blue:heartbeat";
pwms = <&pwm 2 2000000 0>;
pwm-names = "pwm2";
max_brightness = <255>;
linux,default-trigger = "heartbeat";
};
};
gpioleds {
compatible = "gpio-leds";
redled {
label = "red:microSD";
gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "mmc1";
};
};
};
&pwm {
/*
* PWM 0 -- fan
* PWM 1 -- Green LED
* PWM 2 -- Blue LED
* PWM 3 -- on MIPI connector for backlight
*/
pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>;
pinctrl-names = "default";
status = "okay";
};
&usbdrd_dwc3_1 {
dr_mode = "otg";
}; };
...@@ -17,6 +17,40 @@ ...@@ -17,6 +17,40 @@
/ { / {
model = "Hardkernel Odroid XU3"; model = "Hardkernel Odroid XU3";
compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5"; compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5";
pwmleds {
compatible = "pwm-leds";
greenled {
label = "green:mmc0";
pwms = <&pwm 1 2000000 0>;
pwm-names = "pwm1";
/*
* Green LED is much brighter than the others
* so limit its max brightness
*/
max_brightness = <127>;
linux,default-trigger = "mmc0";
};
blueled {
label = "blue:heartbeat";
pwms = <&pwm 2 2000000 0>;
pwm-names = "pwm2";
max_brightness = <255>;
linux,default-trigger = "heartbeat";
};
};
gpioleds {
compatible = "gpio-leds";
redled {
label = "red:microSD";
gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "mmc1";
};
};
}; };
&i2c_0 { &i2c_0 {
...@@ -50,3 +84,19 @@ ina231@45 { ...@@ -50,3 +84,19 @@ ina231@45 {
shunt-resistor = <10000>; shunt-resistor = <10000>;
}; };
}; };
&pwm {
/*
* PWM 0 -- fan
* PWM 1 -- Green LED
* PWM 2 -- Blue LED
* PWM 3 -- on MIPI connector for backlight
*/
pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>;
pinctrl-names = "default";
status = "okay";
};
&usbdrd_dwc3_1 {
dr_mode = "otg";
};
/*
* Hardkernel Odroid XU4 board device tree source
*
* Copyright (c) 2015 Krzysztof Kozlowski
* Copyright (c) 2014 Collabora Ltd.
* Copyright (c) 2013-2015 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
#include "exynos5422-odroidxu3-common.dtsi"
/ {
model = "Hardkernel Odroid XU4";
compatible = "hardkernel,odroid-xu4", "samsung,exynos5800", \
"samsung,exynos5";
pwmleds {
compatible = "pwm-leds";
blueled {
label = "blue:heartbeat";
pwms = <&pwm 2 2000000 0>;
pwm-names = "pwm2";
max_brightness = <255>;
linux,default-trigger = "heartbeat";
};
};
};
&pwm {
/*
* PWM 0 -- fan
* PWM 2 -- Blue LED
*/
pinctrl-0 = <&pwm0_out &pwm2_out>;
pinctrl-names = "default";
samsung,pwm-outputs = <0>, <2>;
status = "okay";
};
&usbdrd_dwc3_1 {
dr_mode = "host";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment